summaryrefslogtreecommitdiff
diff options
context:
space:
mode:
-rw-r--r--CREDITS2
-rw-r--r--MAINTAINERS5
-rwxr-xr-xMAKEALL2
-rw-r--r--Makefile6
-rw-r--r--board/freescale/mpc8313erdb/Makefile2
-rw-r--r--board/freescale/mpc8315erdb/Makefile50
-rw-r--r--board/freescale/mpc8315erdb/config.mk1
-rw-r--r--board/freescale/mpc8315erdb/mpc8315erdb.c132
-rw-r--r--board/freescale/mpc8315erdb/sdram.c120
-rw-r--r--board/freescale/mpc8349itx/Makefile2
-rw-r--r--board/freescale/mpc8360emds/mpc8360emds.c34
-rw-r--r--board/freescale/mpc837xerdb/Makefile50
-rw-r--r--board/freescale/mpc837xerdb/config.mk28
-rw-r--r--board/freescale/mpc837xerdb/mpc837xerdb.c150
-rw-r--r--board/freescale/mpc837xerdb/pci.c59
-rw-r--r--cpu/mpc83xx/cpu_init.c78
-rw-r--r--cpu/mpc83xx/speed.c12
-rw-r--r--doc/README.mpc8315erdb80
-rw-r--r--doc/README.mpc837xerdb98
-rw-r--r--include/configs/MPC8313ERDB.h32
-rw-r--r--include/configs/MPC8315ERDB.h547
-rw-r--r--include/configs/MPC8323ERDB.h2
-rw-r--r--include/configs/MPC832XEMDS.h2
-rw-r--r--include/configs/MPC8360EMDS.h3
-rw-r--r--include/configs/MPC8360ERDK.h11
-rw-r--r--include/configs/MPC837XERDB.h596
-rw-r--r--include/mpc83xx.h13
27 files changed, 2040 insertions, 77 deletions
diff --git a/CREDITS b/CREDITS
index 1130c9e..edf825c 100644
--- a/CREDITS
+++ b/CREDITS
@@ -305,7 +305,7 @@ W: http://www.li-pro.net
N: Dave Liu
E: daveliu@freescale.com
-D: Support for MPC832x, MPC8360, MPC837x
+D: Support for MPC8315, MPC832x, MPC8360, MPC837x
W: www.freescale.com
N: Raymond Lo
diff --git a/MAINTAINERS b/MAINTAINERS
index 40b2b51..fed45f7 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -58,6 +58,10 @@ Conn Clark <clark@esteem.com>
ESTEEM192E MPC8xx
+Joe D'Abbraccio <ljd015@freescale.com>
+
+ MPC837xERDB MPC837x
+
Kári Davíđsson <kd@flaga.is>
FLAGADM MPC823
@@ -232,6 +236,7 @@ The LEOX team <team@leox.org>
Dave Liu <daveliu@freescale.com>
+ MPC8315ERDB MPC8315
MPC832XEMDS MPC832x
MPC8360EMDS MPC8360
MPC837XEMDS MPC837x
diff --git a/MAKEALL b/MAKEALL
index bec3541..8e6713e 100755
--- a/MAKEALL
+++ b/MAKEALL
@@ -309,6 +309,7 @@ LIST_8260=" \
LIST_83xx=" \
MPC8313ERDB_33 \
MPC8313ERDB_66 \
+ MPC8315ERDB \
MPC8323ERDB \
MPC832XEMDS \
MPC832XEMDS_ATM \
@@ -320,6 +321,7 @@ LIST_83xx=" \
MPC8360ERDK_33 \
MPC8360ERDK_66 \
MPC837XEMDS \
+ MPC837XERDB \
sbc8349 \
TQM834x \
"
diff --git a/Makefile b/Makefile
index 8a888b9..1b3d2e6 100644
--- a/Makefile
+++ b/Makefile
@@ -1861,6 +1861,9 @@ MPC8313ERDB_66_config: unconfig
fi ;
@$(MKCONFIG) -a MPC8313ERDB ppc mpc83xx mpc8313erdb freescale
+MPC8315ERDB_config: unconfig
+ @$(MKCONFIG) -a MPC8315ERDB ppc mpc83xx mpc8315erdb freescale
+
MPC8323ERDB_config: unconfig
@$(MKCONFIG) -a MPC8323ERDB ppc mpc83xx mpc8323erdb freescale
@@ -1968,6 +1971,9 @@ MPC837XEMDS_HOST_config: unconfig
fi ;
@$(MKCONFIG) -a MPC837XEMDS ppc mpc83xx mpc837xemds freescale
+MPC837XERDB_config: unconfig
+ @$(MKCONFIG) -a MPC837XERDB ppc mpc83xx mpc837xerdb freescale
+
sbc8349_config: unconfig
@$(MKCONFIG) $(@:_config=) ppc mpc83xx sbc8349
diff --git a/board/freescale/mpc8313erdb/Makefile b/board/freescale/mpc8313erdb/Makefile
index a987e510..e97ba81 100644
--- a/board/freescale/mpc8313erdb/Makefile
+++ b/board/freescale/mpc8313erdb/Makefile
@@ -32,7 +32,7 @@ OBJS := $(addprefix $(obj),$(COBJS))
SOBJS := $(addprefix $(obj),$(SOBJS))
$(LIB): $(obj).depend $(OBJS)
- $(AR) crv $@ $(OBJS)
+ $(AR) $(ARFLAGS) $@ $(OBJS)
clean:
rm -f $(SOBJS) $(OBJS)
diff --git a/board/freescale/mpc8315erdb/Makefile b/board/freescale/mpc8315erdb/Makefile
new file mode 100644
index 0000000..e97ba81
--- /dev/null
+++ b/board/freescale/mpc8315erdb/Makefile
@@ -0,0 +1,50 @@
+#
+# (C) Copyright 2006
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = $(obj)lib$(BOARD).a
+
+COBJS := $(BOARD).o sdram.o
+
+SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS))
+SOBJS := $(addprefix $(obj),$(SOBJS))
+
+$(LIB): $(obj).depend $(OBJS)
+ $(AR) $(ARFLAGS) $@ $(OBJS)
+
+clean:
+ rm -f $(SOBJS) $(OBJS)
+
+distclean: clean
+ rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/freescale/mpc8315erdb/config.mk b/board/freescale/mpc8315erdb/config.mk
new file mode 100644
index 0000000..f768264
--- /dev/null
+++ b/board/freescale/mpc8315erdb/config.mk
@@ -0,0 +1 @@
+TEXT_BASE = 0xFE000000
diff --git a/board/freescale/mpc8315erdb/mpc8315erdb.c b/board/freescale/mpc8315erdb/mpc8315erdb.c
new file mode 100644
index 0000000..7af36dd
--- /dev/null
+++ b/board/freescale/mpc8315erdb/mpc8315erdb.c
@@ -0,0 +1,132 @@
+/*
+ * Copyright (C) 2007 Freescale Semiconductor, Inc.
+ *
+ * Author: Scott Wood <scottwood@freescale.com>
+ * Dave Liu <daveliu@freescale.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS for A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <i2c.h>
+#if defined(CONFIG_OF_LIBFDT)
+#include <libfdt.h>
+#endif
+#include <pci.h>
+#include <mpc83xx.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int board_early_init_f(void)
+{
+ volatile immap_t *im = (immap_t *)CFG_IMMR;
+
+ if (im->pmc.pmccr1 & PMCCR1_POWER_OFF)
+ gd->flags |= GD_FLG_SILENT;
+
+ return 0;
+}
+
+static u8 read_board_info(void)
+{
+ u8 val8;
+ i2c_set_bus_num(0);
+
+ if (i2c_read(CFG_I2C_PCF8574A_ADDR, 0, 0, &val8, 1) == 0)
+ return val8;
+ else
+ return 0;
+}
+
+int checkboard(void)
+{
+ static const char * const rev_str[] = {
+ "0.0",
+ "0.1",
+ "1.0",
+ "1.1",
+ "<unknown>",
+ };
+ u8 info;
+ int i;
+
+ info = read_board_info();
+ i = (!info) ? 4: info & 0x03;
+
+ printf("Board: Freescale MPC8315ERDB Rev %s\n", rev_str[i]);
+
+ return 0;
+}
+
+static struct pci_region pci_regions[] = {
+ {
+ bus_start: CFG_PCI_MEM_BASE,
+ phys_start: CFG_PCI_MEM_PHYS,
+ size: CFG_PCI_MEM_SIZE,
+ flags: PCI_REGION_MEM | PCI_REGION_PREFETCH
+ },
+ {
+ bus_start: CFG_PCI_MMIO_BASE,
+ phys_start: CFG_PCI_MMIO_PHYS,
+ size: CFG_PCI_MMIO_SIZE,
+ flags: PCI_REGION_MEM
+ },
+ {
+ bus_start: CFG_PCI_IO_BASE,
+ phys_start: CFG_PCI_IO_PHYS,
+ size: CFG_PCI_IO_SIZE,
+ flags: PCI_REGION_IO
+ }
+};
+
+void pci_init_board(void)
+{
+ volatile immap_t *immr = (volatile immap_t *)CFG_IMMR;
+ volatile clk83xx_t *clk = (volatile clk83xx_t *)&immr->clk;
+ volatile law83xx_t *pci_law = immr->sysconf.pcilaw;
+ struct pci_region *reg[] = { pci_regions };
+ int warmboot;
+
+ /* Enable all 3 PCI_CLK_OUTPUTs. */
+ clk->occr |= 0xe0000000;
+
+ /*
+ * Configure PCI Local Access Windows
+ */
+ pci_law[0].bar = CFG_PCI_MEM_PHYS & LAWBAR_BAR;
+ pci_law[0].ar = LBLAWAR_EN | LBLAWAR_512MB;
+
+ pci_law[1].bar = CFG_PCI_IO_PHYS & LAWBAR_BAR;
+ pci_law[1].ar = LBLAWAR_EN | LBLAWAR_1MB;
+
+ warmboot = gd->bd->bi_bootflags & BOOTFLAG_WARM;
+ warmboot |= immr->pmc.pmccr1 & PMCCR1_POWER_OFF;
+
+ mpc83xx_pci_init(1, reg, warmboot);
+}
+
+#if defined(CONFIG_OF_BOARD_SETUP)
+void ft_board_setup(void *blob, bd_t *bd)
+{
+ ft_cpu_setup(blob, bd);
+#ifdef CONFIG_PCI
+ ft_pci_setup(blob, bd);
+#endif
+}
+#endif
diff --git a/board/freescale/mpc8315erdb/sdram.c b/board/freescale/mpc8315erdb/sdram.c
new file mode 100644
index 0000000..f97e3c7
--- /dev/null
+++ b/board/freescale/mpc8315erdb/sdram.c
@@ -0,0 +1,120 @@
+/*
+ * Copyright (C) 2007 Freescale Semiconductor, Inc.
+ *
+ * Authors: Nick.Spence@freescale.com
+ * Wilson.Lo@freescale.com
+ * scottwood@freescale.com
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS for A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <mpc83xx.h>
+#include <spd_sdram.h>
+
+#include <asm/bitops.h>
+#include <asm/io.h>
+
+#include <asm/processor.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+static void resume_from_sleep(void)
+{
+ u32 magic = *(u32 *)0;
+
+ typedef void (*func_t)(void);
+ func_t resume = *(func_t *)4;
+
+ if (magic == 0xf5153ae5)
+ resume();
+
+ gd->flags &= ~GD_FLG_SILENT;
+ puts("\nResume from sleep failed: bad magic word\n");
+}
+
+/* Fixed sdram init -- doesn't use serial presence detect.
+ *
+ * This is useful for faster booting in configs where the RAM is unlikely
+ * to be changed, or for things like NAND booting where space is tight.
+ */
+static long fixed_sdram(void)
+{
+ volatile immap_t *im = (volatile immap_t *)CFG_IMMR;
+ u32 msize = CFG_DDR_SIZE * 1024 * 1024;
+ u32 msize_log2 = __ilog2(msize);
+
+ im->sysconf.ddrlaw[0].bar = CFG_DDR_SDRAM_BASE >> 12;
+ im->sysconf.ddrlaw[0].ar = LBLAWAR_EN | (msize_log2 - 1);
+ im->sysconf.ddrcdr = CFG_DDRCDR_VALUE;
+
+ /*
+ * Erratum DDR3 requires a 50ms delay after clearing DDRCDR[DDR_cfg],
+ * or the DDR2 controller may fail to initialize correctly.
+ */
+ udelay(50000);
+
+ im->ddr.csbnds[0].csbnds = (msize - 1) >> 24;
+ im->ddr.cs_config[0] = CFG_DDR_CS0_CONFIG;
+
+ /* Currently we use only one CS, so disable the other bank. */
+ im->ddr.cs_config[1] = 0;
+
+ im->ddr.sdram_clk_cntl = CFG_DDR_SDRAM_CLK_CNTL;
+ im->ddr.timing_cfg_3 = CFG_DDR_TIMING_3;
+ im->ddr.timing_cfg_1 = CFG_DDR_TIMING_1;
+ im->ddr.timing_cfg_2 = CFG_DDR_TIMING_2;
+ im->ddr.timing_cfg_0 = CFG_DDR_TIMING_0;
+
+ if (im->pmc.pmccr1 & PMCCR1_POWER_OFF)
+ im->ddr.sdram_cfg = CFG_DDR_SDRAM_CFG | SDRAM_CFG_BI;
+ else
+ im->ddr.sdram_cfg = CFG_DDR_SDRAM_CFG;
+
+ im->ddr.sdram_cfg2 = CFG_DDR_SDRAM_CFG2;
+ im->ddr.sdram_mode = CFG_DDR_MODE;
+ im->ddr.sdram_mode2 = CFG_DDR_MODE2;
+
+ im->ddr.sdram_interval = CFG_DDR_INTERVAL;
+ sync();
+
+ /* enable DDR controller */
+ im->ddr.sdram_cfg |= SDRAM_CFG_MEM_EN;
+ sync();
+
+ return msize;
+}
+
+long int initdram(int board_type)
+{
+ volatile immap_t *im = (volatile immap_t *)CFG_IMMR;
+ u32 msize;
+
+ if ((im->sysconf.immrbar & IMMRBAR_BASE_ADDR) != (u32)im)
+ return -1;
+
+ /* DDR SDRAM */
+ msize = fixed_sdram();
+
+ if (im->pmc.pmccr1 & PMCCR1_POWER_OFF)
+ resume_from_sleep();
+
+ /* return total bus SDRAM size(bytes) -- DDR */
+ return msize;
+}
diff --git a/board/freescale/mpc8349itx/Makefile b/board/freescale/mpc8349itx/Makefile
index 31bcdb8..265e341 100644
--- a/board/freescale/mpc8349itx/Makefile
+++ b/board/freescale/mpc8349itx/Makefile
@@ -31,7 +31,7 @@ OBJS := $(addprefix $(obj),$(COBJS))
SOBJS := $(addprefix $(obj),$(SOBJS))
$(LIB): $(obj).depend $(OBJS)
- $(AR) crv $@ $(OBJS)
+ $(AR) $(ARFLAGS) $@ $(OBJS)
clean:
rm -f $(SOBJS) $(OBJS)
diff --git a/board/freescale/mpc8360emds/mpc8360emds.c b/board/freescale/mpc8360emds/mpc8360emds.c
index 2fcef8b..f909a33 100644
--- a/board/freescale/mpc8360emds/mpc8360emds.c
+++ b/board/freescale/mpc8360emds/mpc8360emds.c
@@ -316,30 +316,36 @@ void ft_board_setup(void *blob, bd_t *bd)
immr->sysconf.spridr == SPR_8360E_REV21) {
int nodeoffset;
const char *prop;
- const char *path;
+ int path;
- nodeoffset = fdt_path_offset(fdt, "/aliases");
+ nodeoffset = fdt_path_offset(blob, "/aliases");
if (nodeoffset >= 0) {
#if defined(CONFIG_HAS_ETH0)
/* fixup UCC 1 if using rgmii-id mode */
- path = fdt_getprop(blob, nodeoffset, "ethernet0", NULL);
- if (path) {
- prop = fdt_getprop(blob, nodeoffset,
- "phy-connection-type", 0);
+ prop = fdt_getprop(blob, nodeoffset, "ethernet0", NULL);
+ if (prop) {
+ path = fdt_path_offset(blob, prop);
+ prop = fdt_getprop(blob, path,
+ "phy-connection-type", 0);
if (prop && (strcmp(prop, "rgmii-id") == 0))
- fdt_setprop(blob, nodeoffset, "phy-connection-type",
- "rgmii-rxid", sizeof("rgmii-rxid"));
+ fdt_setprop(blob, path,
+ "phy-connection-type",
+ "rgmii-rxid",
+ sizeof("rgmii-rxid"));
}
#endif
#if defined(CONFIG_HAS_ETH1)
/* fixup UCC 2 if using rgmii-id mode */
- path = fdt_getprop(blob, nodeoffset, "ethernet1", NULL);
- if (path) {
- prop = fdt_getprop(blob, nodeoffset,
- "phy-connection-type", 0);
+ prop = fdt_getprop(blob, nodeoffset, "ethernet1", NULL);
+ if (prop) {
+ path = fdt_path_offset(blob, prop);
+ prop = fdt_getprop(blob, path,
+ "phy-connection-type", 0);
if (prop && (strcmp(prop, "rgmii-id") == 0))
- fdt_setprop(blob, nodeoffset, "phy-connection-type",
- "rgmii-rxid", sizeof("rgmii-rxid"));
+ fdt_setprop(blob, path,
+ "phy-connection-type",
+ "rgmii-rxid",
+ sizeof("rgmii-rxid"));
}
#endif
}
diff --git a/board/freescale/mpc837xerdb/Makefile b/board/freescale/mpc837xerdb/Makefile
new file mode 100644
index 0000000..5ec7a87
--- /dev/null
+++ b/board/freescale/mpc837xerdb/Makefile
@@ -0,0 +1,50 @@
+#
+# (C) Copyright 2006
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = $(obj)lib$(BOARD).a
+
+COBJS := $(BOARD).o pci.o
+
+SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS))
+SOBJS := $(addprefix $(obj),$(SOBJS))
+
+$(LIB): $(obj).depend $(OBJS)
+ $(AR) $(ARFLAGS) $@ $(OBJS)
+
+clean:
+ rm -f $(SOBJS) $(OBJS)
+
+distclean: clean
+ rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/freescale/mpc837xerdb/config.mk b/board/freescale/mpc837xerdb/config.mk
new file mode 100644
index 0000000..5675f81
--- /dev/null
+++ b/board/freescale/mpc837xerdb/config.mk
@@ -0,0 +1,28 @@
+#
+# (C) Copyright 2006
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+#
+# MPC837xERDB
+#
+
+TEXT_BASE = 0xFE000000
diff --git a/board/freescale/mpc837xerdb/mpc837xerdb.c b/board/freescale/mpc837xerdb/mpc837xerdb.c
new file mode 100644
index 0000000..2d42595
--- /dev/null
+++ b/board/freescale/mpc837xerdb/mpc837xerdb.c
@@ -0,0 +1,150 @@
+/*
+ * Copyright (C) 2007 Freescale Semiconductor, Inc.
+ * Kevin Lam <kevin.lam@freescale.com>
+ * Joe D'Abbraccio <joe.d'abbraccio@freescale.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ */
+
+#include <common.h>
+#include <i2c.h>
+#include <spd.h>
+#include <asm/io.h>
+#if defined(CONFIG_SPD_EEPROM)
+#include <spd_sdram.h>
+#endif
+
+#if defined(CFG_DRAM_TEST)
+int
+testdram(void)
+{
+ uint *pstart = (uint *) CFG_MEMTEST_START;
+ uint *pend = (uint *) CFG_MEMTEST_END;
+ uint *p;
+
+ printf("Testing DRAM from 0x%08x to 0x%08x\n",
+ CFG_MEMTEST_START,
+ CFG_MEMTEST_END);
+
+ printf("DRAM test phase 1:\n");
+ for (p = pstart; p < pend; p++)
+ *p = 0xaaaaaaaa;
+
+ for (p = pstart; p < pend; p++) {
+ if (*p != 0xaaaaaaaa) {
+ printf("DRAM test fails at: %08x\n", (uint) p);
+ return 1;
+ }
+ }
+
+ printf("DRAM test phase 2:\n");
+ for (p = pstart; p < pend; p++)
+ *p = 0x55555555;
+
+ for (p = pstart; p < pend; p++) {
+ if (*p != 0x55555555) {
+ printf("DRAM test fails at: %08x\n", (uint) p);
+ return 1;
+ }
+ }
+
+ printf("DRAM test passed.\n");
+ return 0;
+}
+#endif
+
+int board_early_init_f(void)
+{
+ return 0;
+}
+
+#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRC)
+void ddr_enable_ecc(unsigned int dram_size);
+#endif
+int fixed_sdram(void);
+
+long int initdram(int board_type)
+{
+ immap_t *im = (immap_t *) CFG_IMMR;
+ u32 msize = 0;
+
+ if ((im->sysconf.immrbar & IMMRBAR_BASE_ADDR) != (u32) im)
+ return -1;
+
+#if defined(CONFIG_SPD_EEPROM)
+ msize = spd_sdram();
+#else
+ msize = fixed_sdram();
+#endif
+
+#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRC)
+ /* Initialize DDR ECC byte */
+ ddr_enable_ecc(msize * 1024 * 1024);
+#endif
+ /* return total bus DDR size(bytes) */
+ return (msize * 1024 * 1024);
+}
+
+#if !defined(CONFIG_SPD_EEPROM)
+/*************************************************************************
+ * fixed sdram init -- doesn't use serial presence detect.
+ ************************************************************************/
+int fixed_sdram(void)
+{
+ immap_t *im = (immap_t *) CFG_IMMR;
+ u32 msize = CFG_DDR_SIZE * 1024 * 1024;
+ u32 msize_log2 = __ilog2(msize);
+
+ im->sysconf.ddrlaw[0].bar = CFG_DDR_SDRAM_BASE >> 12;
+ im->sysconf.ddrlaw[0].ar = LBLAWAR_EN | (msize_log2 - 1);
+
+ im->sysconf.ddrcdr = CFG_DDRCDR_VALUE;
+ udelay(50000);
+
+ im->ddr.sdram_clk_cntl = CFG_DDR_SDRAM_CLK_CNTL;
+ udelay(1000);
+
+ im->ddr.csbnds[0].csbnds = CFG_DDR_CS0_BNDS;
+ im->ddr.cs_config[0] = CFG_DDR_CS0_CONFIG;
+ udelay(1000);
+
+ im->ddr.timing_cfg_0 = CFG_DDR_TIMING_0;
+ im->ddr.timing_cfg_1 = CFG_DDR_TIMING_1;
+ im->ddr.timing_cfg_2 = CFG_DDR_TIMING_2;
+ im->ddr.timing_cfg_3 = CFG_DDR_TIMING_3;
+ im->ddr.sdram_cfg = CFG_DDR_SDRAM_CFG;
+ im->ddr.sdram_cfg2 = CFG_DDR_SDRAM_CFG2;
+ im->ddr.sdram_mode = CFG_DDR_MODE;
+ im->ddr.sdram_mode2 = CFG_DDR_MODE2;
+ im->ddr.sdram_interval = CFG_DDR_INTERVAL;
+ sync();
+ udelay(1000);
+
+ im->ddr.sdram_cfg |= SDRAM_CFG_MEM_EN;
+ udelay(2000);
+ return CFG_DDR_SIZE;
+}
+#endif /*!CFG_SPD_EEPROM */
+
+int checkboard(void)
+{
+ puts("Board: Freescale MPC837xERDB\n");
+ return 0;
+}
+
+#if defined(CONFIG_OF_BOARD_SETUP)
+
+void ft_board_setup(void *blob, bd_t *bd)
+{
+#ifdef CONFIG_PCI
+ ft_pci_setup(blob, bd);
+#endif
+ ft_cpu_setup(blob, bd);
+}
+#endif /* CONFIG_OF_BOARD_SETUP */
diff --git a/board/freescale/mpc837xerdb/pci.c b/board/freescale/mpc837xerdb/pci.c
new file mode 100644
index 0000000..26e7320
--- /dev/null
+++ b/board/freescale/mpc837xerdb/pci.c
@@ -0,0 +1,59 @@
+/*
+ * Copyright (C) 2007 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ */
+
+#include <common.h>
+#include <mpc83xx.h>
+#include <pci.h>
+
+#if defined(CONFIG_PCI)
+static struct pci_region pci_regions[] = {
+ {
+ bus_start: CFG_PCI_MEM_BASE,
+ phys_start: CFG_PCI_MEM_PHYS,
+ size: CFG_PCI_MEM_SIZE,
+ flags: PCI_REGION_MEM | PCI_REGION_PREFETCH
+ },
+ {
+ bus_start: CFG_PCI_MMIO_BASE,
+ phys_start: CFG_PCI_MMIO_PHYS,
+ size: CFG_PCI_MMIO_SIZE,
+ flags: PCI_REGION_MEM
+ },
+ {
+ bus_start: CFG_PCI_IO_BASE,
+ phys_start: CFG_PCI_IO_PHYS,
+ size: CFG_PCI_IO_SIZE,
+ flags: PCI_REGION_IO
+ }
+};
+
+void pci_init_board(void)
+{
+ volatile immap_t *immr = (volatile immap_t *)CFG_IMMR;
+ volatile clk83xx_t *clk = (volatile clk83xx_t *)&immr->clk;
+ volatile law83xx_t *pci_law = immr->sysconf.pcilaw;
+ struct pci_region *reg[] = { pci_regions };
+
+ /* Enable all 5 PCI_CLK_OUTPUTS */
+ clk->occr |= 0xf8000000;
+ udelay(2000);
+
+ /* Configure PCI Local Access Windows */
+ pci_law[0].bar = CFG_PCI_MEM_PHYS & LAWBAR_BAR;
+ pci_law[0].ar = LBLAWAR_EN | LBLAWAR_512MB;
+
+ pci_law[1].bar = CFG_PCI_IO_PHYS & LAWBAR_BAR;
+ pci_law[1].ar = LBLAWAR_EN | LBLAWAR_1MB;
+
+ mpc83xx_pci_init(1, reg, 0);
+}
+#endif /* CONFIG_PCI */
diff --git a/cpu/mpc83xx/cpu_init.c b/cpu/mpc83xx/cpu_init.c
index 2b92be0..3337d8c 100644
--- a/cpu/mpc83xx/cpu_init.c
+++ b/cpu/mpc83xx/cpu_init.c
@@ -73,59 +73,93 @@ void cpu_init_f (volatile immap_t * im)
(CFG_ACR_PIPE_DEP << ACR_PIPE_DEP_SHIFT);
#endif
+#ifdef CFG_SPCR_TSECEP
+ /* eTSEC Emergency priority */
+ im->sysconf.spcr = (im->sysconf.spcr & ~SPCR_TSECEP) | (CFG_SPCR_TSECEP << SPCR_TSECEP_SHIFT);
+#endif
+
+#ifdef CFG_ACR_RPTCNT
+ /* Arbiter repeat count */
+ im->arbiter.acr = (im->arbiter.acr & ~(ACR_RPTCNT)) |
+ (CFG_ACR_RPTCNT << ACR_RPTCNT_SHIFT);
+#endif
+
+#ifdef CFG_SPCR_TSECEP
+ /* all TSEC's Emergency priority */
+ im->sysconf.spcr = (im->sysconf.spcr & ~SPCR_TSECEP) |
+ (CFG_SPCR_TSECEP << SPCR_TSECEP_SHIFT);
+#endif
+
#ifdef CFG_SPCR_TSEC1EP
/* TSEC1 Emergency priority */
- im->sysconf.spcr = (im->sysconf.spcr & ~SPCR_TSEC1EP) | (CFG_SPCR_TSEC1EP << SPCR_TSEC1EP_SHIFT);
+ im->sysconf.spcr = (im->sysconf.spcr & ~SPCR_TSEC1EP) |
+ (CFG_SPCR_TSEC1EP << SPCR_TSEC1EP_SHIFT);
#endif
#ifdef CFG_SPCR_TSEC2EP
/* TSEC2 Emergency priority */
- im->sysconf.spcr = (im->sysconf.spcr & ~SPCR_TSEC2EP) | (CFG_SPCR_TSEC2EP << SPCR_TSEC2EP_SHIFT);
+ im->sysconf.spcr = (im->sysconf.spcr & ~SPCR_TSEC2EP) |
+ (CFG_SPCR_TSEC2EP << SPCR_TSEC2EP_SHIFT);
+#endif
+
+#ifdef CFG_SCCR_ENCCM
+ /* Encryption clock mode */
+ im->clk.sccr = (im->clk.sccr & ~SCCR_ENCCM) |
+ (CFG_SCCR_ENCCM << SCCR_PCICM_SHIFT);
+#endif
+
+#ifdef CFG_SCCR_PCICM
+ /* PCI & DMA clock mode */
+ im->clk.sccr = (im->clk.sccr & ~SCCR_PCICM) |
+ (CFG_SCCR_PCICM << SCCR_PCICM_SHIFT);
+#endif
+
+#ifdef CFG_SCCR_TSECCM
+ /* all TSEC's clock mode */
+ im->clk.sccr = (im->clk.sccr & ~SCCR_TSECCM) |
+ (CFG_SCCR_TSECCM << SCCR_TSECCM_SHIFT);
#endif
#ifdef CFG_SCCR_TSEC1CM
/* TSEC1 clock mode */
- im->clk.sccr = (im->clk.sccr & ~SCCR_TSEC1CM) | (CFG_SCCR_TSEC1CM << SCCR_TSEC1CM_SHIFT);
+ im->clk.sccr = (im->clk.sccr & ~SCCR_TSEC1CM) |
+ (CFG_SCCR_TSEC1CM << SCCR_TSEC1CM_SHIFT);
#endif
#ifdef CFG_SCCR_TSEC2CM
- /* TSEC2 & I2C1 clock mode */
- im->clk.sccr = (im->clk.sccr & ~SCCR_TSEC2CM) | (CFG_SCCR_TSEC2CM << SCCR_TSEC2CM_SHIFT);
+ /* TSEC2 clock mode */
+ im->clk.sccr = (im->clk.sccr & ~SCCR_TSEC2CM) |
+ (CFG_SCCR_TSEC2CM << SCCR_TSEC2CM_SHIFT);
#endif
#ifdef CFG_SCCR_TSEC1ON
/* TSEC1 clock switch */
- im->clk.sccr = (im->clk.sccr & ~SCCR_TSEC1ON) | (CFG_SCCR_TSEC1ON << SCCR_TSEC1ON_SHIFT);
+ im->clk.sccr = (im->clk.sccr & ~SCCR_TSEC1ON) |
+ (CFG_SCCR_TSEC1ON << SCCR_TSEC1ON_SHIFT);
#endif
#ifdef CFG_SCCR_TSEC2ON
/* TSEC2 clock switch */
- im->clk.sccr = (im->clk.sccr & ~SCCR_TSEC2ON) | (CFG_SCCR_TSEC2ON << SCCR_TSEC2ON_SHIFT);
+ im->clk.sccr = (im->clk.sccr & ~SCCR_TSEC2ON) |
+ (CFG_SCCR_TSEC2ON << SCCR_TSEC2ON_SHIFT);
#endif
#ifdef CFG_SCCR_USBMPHCM
/* USB MPH clock mode */
- im->clk.sccr = (im->clk.sccr & ~SCCR_USBMPHCM) | (CFG_SCCR_USBMPHCM << SCCR_USBMPHCM_SHIFT);
-#endif
-
-#ifdef CFG_SCCR_PCICM
- /* PCI & DMA clock mode */
- im->clk.sccr = (im->clk.sccr & ~SCCR_PCICM) | (CFG_SCCR_PCICM << SCCR_PCICM_SHIFT);
+ im->clk.sccr = (im->clk.sccr & ~SCCR_USBMPHCM) |
+ (CFG_SCCR_USBMPHCM << SCCR_USBMPHCM_SHIFT);
#endif
#ifdef CFG_SCCR_USBDRCM
/* USB DR clock mode */
- im->clk.sccr = (im->clk.sccr & ~SCCR_USBDRCM) | (CFG_SCCR_USBDRCM << SCCR_USBDRCM_SHIFT);
+ im->clk.sccr = (im->clk.sccr & ~SCCR_USBDRCM) |
+ (CFG_SCCR_USBDRCM << SCCR_USBDRCM_SHIFT);
#endif
-#ifdef CFG_SCCR_ENCCM
- /* Encryption clock mode */
- im->clk.sccr = (im->clk.sccr & ~SCCR_ENCCM) | (CFG_SCCR_ENCCM << SCCR_PCICM_SHIFT);
-#endif
-
-#ifdef CFG_ACR_RPTCNT
- /* Arbiter repeat count */
- im->arbiter.acr = ((im->arbiter.acr & ~(ACR_RPTCNT)) | (CFG_ACR_RPTCNT << ACR_RPTCNT_SHIFT));
+#ifdef CFG_SCCR_SATACM
+ /* SATA controller clock mode */
+ im->clk.sccr = (im->clk.sccr & ~SCCR_SATACM) |
+ (CFG_SCCR_SATACM << SCCR_SATACM_SHIFT);
#endif
/* RSR - Reset Status Register - clear all status (4.6.1.3) */
diff --git a/cpu/mpc83xx/speed.c b/cpu/mpc83xx/speed.c
index 4f5a866..61c9379 100644
--- a/cpu/mpc83xx/speed.c
+++ b/cpu/mpc83xx/speed.c
@@ -367,21 +367,21 @@ int get_clocks(void)
#endif
#if defined(CONFIG_MPC837X) || defined(CONFIG_MPC8315)
- switch ((sccr & SCCR_SATA1CM) >> SCCR_SATA1CM_SHIFT) {
- case 0:
+ switch ((sccr & SCCR_SATACM) >> SCCR_SATACM_SHIFT) {
+ case SCCR_SATACM_0:
sata_clk = 0;
break;
- case 1:
+ case SCCR_SATACM_1:
sata_clk = csb_clk;
break;
- case 2:
+ case SCCR_SATACM_2:
sata_clk = csb_clk / 2;
break;
- case 3:
+ case SCCR_SATACM_3:
sata_clk = csb_clk / 3;
break;
default:
- /* unkown SCCR_SATA1CM value */
+ /* unkown SCCR_SATACM value */
return -11;
}
#endif
diff --git a/doc/README.mpc8315erdb b/doc/README.mpc8315erdb
new file mode 100644
index 0000000..c630cf8
--- /dev/null
+++ b/doc/README.mpc8315erdb
@@ -0,0 +1,80 @@
+Freescale MPC8315ERDB Board
+-----------------------------------------
+
+1. Board Switches and Jumpers
+
+ S3 is used to set CFG_RESET_SOURCE.
+
+ To boot the image at 0xFE000000 in NOR flash, use these DIP
+ switche settings for S3 S4:
+
+ +------+ +------+
+ | | | **** |
+ | **** | | |
+ +------+ ON +------+ ON
+ 4321 4321
+ (where the '*' indicates the position of the tab of the switch.)
+
+2. Memory Map
+ The memory map looks like this:
+
+ 0x0000_0000 0x07ff_ffff DDR 128M
+ 0x8000_0000 0x8fff_ffff PCI MEM 256M
+ 0x9000_0000 0x9fff_ffff PCI_MMIO 256M
+ 0xe000_0000 0xe00f_ffff IMMR 1M
+ 0xe030_0000 0xe03f_ffff PCI IO 1M
+ 0xe060_0000 0xe060_7fff NAND FLASH (CS1) 32K
+ 0xfe00_0000 0xfe7f_ffff NOR FLASH (CS0) 8M
+
+3. Definitions
+
+3.1 Explanation of NEW definitions in:
+
+ include/configs/MPC8315ERDB.h
+
+ CONFIG_MPC83xx MPC83xx family
+ CONFIG_MPC831x MPC831x specific
+ CONFIG_MPC8315 MPC8315 specific
+ CONFIG_MPC8315ERDB MPC8315ERDB board specific
+
+4. Compilation
+
+ Assuming you're using BASH (or similar) as your shell:
+
+ export CROSS_COMPILE=your-cross-compiler-prefix-
+ make distclean
+ make MPC8315ERDB_config
+ make all
+
+5. Downloading and Flashing Images
+
+5.1 Reflash U-boot Image using U-boot
+
+ tftp 40000 u-boot.bin
+ protect off all
+ erase fe000000 fe1fffff
+
+ cp.b 40000 fe000000 xxxx
+ protect on all
+
+ You have to supply the correct byte count with 'xxxx'
+ from the TFTP result log.
+
+5.2 Downloading and Booting Linux Kernel
+
+ Ensure that all networking-related environment variables are set
+ properly (including ipaddr, serverip, gatewayip (if needed),
+ netmask, ethaddr, eth1addr, rootpath (if using NFS root),
+ fdtfile, and bootfile).
+
+ Then, do one of the following, depending on whether you
+ want an NFS root or a ramdisk root:
+
+ =>run nfsboot
+ or
+ =>run ramboot
+
+6 Notes
+
+ Booting from NAND flash is not yet supported.
+ The console baudrate for MPC8315ERDB is 115200bps.
diff --git a/doc/README.mpc837xerdb b/doc/README.mpc837xerdb
new file mode 100644
index 0000000..8f0192a
--- /dev/null
+++ b/doc/README.mpc837xerdb
@@ -0,0 +1,98 @@
+Freescale MPC837xEMDS Board
+-----------------------------------------
+
+1. Board Description
+
+ The MPC837xE-RDB are reference boards featuring the Freescale MPC8377E,
+ MPC8378E, and the MPC8379E processors in a Mini-ITX form factor.
+
+ The MPC837xE-RDB's have the following common features:
+
+ A) 256-MBytes on-board DDR2 unbuffered SDRAM
+ B) 8-Mbytes NOR Flash
+ C) 32-MBytes NAND Flash
+ D) 1 Secure Digital High Speed Card (SDHC) Interface
+ E) 1 Gigabit Ethernet
+ F) 5-port Ethernet switch (Vitesse 7385)
+ G) 1 32-bit, 3.3 V, PCI slot
+ H) 1 32-bit, 3.3 V, Mini-PCI slot
+ I) 4-port USB 2.0 Hub
+ J) 1-port OTG USB
+ K) 2 serial ports (top main console)
+ L) on board Oscillator: 66M
+
+ The MPC837xE-RDB's have the following differences:
+
+ MPC8377E-RDB MPC8378E-RDB MPC8379E-RDB
+ SATA controllers 2 0 4
+ PCI-Express (mini) 2 2 0
+ SGMII Ports 0 2 0
+
+
+2. Memory Map
+
+2.1. The memory map should look pretty much like this:
+
+ Address Range Device Size Port Size
+ (Bytes) (Bits)
+ =========================== ================= ======= =========
+ 0x0000_0000 0x0fff_ffff DDR 256M 64
+ 0x1000_0000 0x7fff_ffff Empty 1.75G -
+ 0x8000_0000 0x9fff_ffff PCI1 memory space 512M 32
+ 0xa000_0000 0xbfff_ffff PCI2 memory space 512M 32
+ 0xc200_0000 0xc2ff_ffff PCI1 I/O space 16M 32
+ 0xc300_0000 0xc3ff_ffff PCI2 I/O space 16M 32
+ 0xe000_0000 0xe00f_ffff Int Mem Reg Space 1M -
+ 0xe280_0000 0xe47f_ffff NAND Flash 32M 8
+ 0xfe00_0000 0xfe7f_ffff NOR Flash on CS0 8M 16
+
+
+3. Definitions
+
+3.1 Explanation of NEW definitions in:
+
+ include/configs/MPC837XERDB.h
+
+ CONFIG_MPC83XX MPC83xx family for both MPC8349 and MPC8360
+ CONFIG_MPC837X MPC837x specific
+ CONFIG_MPC837XERDB MPC837XEMDS board specific
+
+
+4. Compilation
+
+ Assuming you're using BASH shell:
+
+ export CROSS_COMPILE=your-cross-compile-prefix
+ cd u-boot
+ make distclean
+ make MPC837XERDB_config
+ make
+
+
+5. Downloading and Flashing Images
+
+5.0 Download over serial line using Kermit:
+
+ loadb $loadaddr
+ [Drop to kermit:
+ ^\c
+ send <u-boot-bin-image>
+ c
+ ]
+
+
+ Or via tftp:
+
+ tftp $loadaddr u-boot.bin
+
+5.1 Reflash U-boot Image using U-boot
+
+ tftp $loadaddr u-boot.bin
+ protect off fe000000 fe0fffff
+ erase fe000000 fe0fffff
+ cp.b $loadaddr fe000000 $filesize
+
+
+6. Additional Notes:
+ 1) The console is connected to the top RS-232 connector and the
+ baudrate for MPC837XE-RDB is 115200bps.
diff --git a/include/configs/MPC8313ERDB.h b/include/configs/MPC8313ERDB.h
index 455bbe0..f12a3e6 100644
--- a/include/configs/MPC8313ERDB.h
+++ b/include/configs/MPC8313ERDB.h
@@ -76,10 +76,10 @@
* seem to have the SPD connected to I2C.
*/
#define CFG_DDR_SIZE 128 /* MB */
-#define CFG_DDR_CONFIG ( CSCONFIG_EN | CSCONFIG_AP \
- | 0x00040000 /* TODO */ \
+#define CFG_DDR_CONFIG ( CSCONFIG_EN \
+ | 0x00010000 /* TODO */ \
| CSCONFIG_ROW_BIT_13 | CSCONFIG_COL_BIT_10 )
- /* 0x80840102 */
+ /* 0x80010102 */
#define CFG_DDR_TIMING_3 0x00000000
#define CFG_DDR_TIMING_0 ( ( 0 << TIMING_CFG0_RWT_SHIFT ) \
@@ -92,25 +92,25 @@
| ( 2 << TIMING_CFG0_MRS_CYC_SHIFT ) )
/* 0x00220802 */
#define CFG_DDR_TIMING_1 ( ( 3 << TIMING_CFG1_PRETOACT_SHIFT ) \
- | ( 9 << TIMING_CFG1_ACTTOPRE_SHIFT ) \
+ | ( 8 << TIMING_CFG1_ACTTOPRE_SHIFT ) \
| ( 3 << TIMING_CFG1_ACTTORW_SHIFT ) \
| ( 5 << TIMING_CFG1_CASLAT_SHIFT ) \
- | (13 << TIMING_CFG1_REFREC_SHIFT ) \
+ | (10 << TIMING_CFG1_REFREC_SHIFT ) \
| ( 3 << TIMING_CFG1_WRREC_SHIFT ) \
| ( 2 << TIMING_CFG1_ACTTOACT_SHIFT ) \
| ( 2 << TIMING_CFG1_WRTORD_SHIFT ) )
- /* 0x3935d322 */
-#define CFG_DDR_TIMING_2 ( ( 0 << TIMING_CFG2_ADD_LAT_SHIFT ) \
- | (31 << TIMING_CFG2_CPO_SHIFT ) \
+ /* 0x3835a322 */
+#define CFG_DDR_TIMING_2 ( ( 1 << TIMING_CFG2_ADD_LAT_SHIFT ) \
+ | ( 5 << TIMING_CFG2_CPO_SHIFT ) \
| ( 2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT ) \
| ( 2 << TIMING_CFG2_RD_TO_PRE_SHIFT ) \
| ( 2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT ) \
| ( 3 << TIMING_CFG2_CKE_PLS_SHIFT ) \
- | (10 << TIMING_CFG2_FOUR_ACT_SHIFT) )
- /* 0x0f9048ca */ /* P9-45,may need tuning */
-#define CFG_DDR_INTERVAL ( ( 800 << SDRAM_INTERVAL_REFINT_SHIFT ) \
- | ( 100 << SDRAM_INTERVAL_BSTOPRE_SHIFT ) )
- /* 0x03200064 */
+ | ( 6 << TIMING_CFG2_FOUR_ACT_SHIFT) )
+ /* 0x129048c6 */ /* P9-45,may need tuning */
+#define CFG_DDR_INTERVAL ( ( 1296 << SDRAM_INTERVAL_REFINT_SHIFT ) \
+ | ( 1280 << SDRAM_INTERVAL_BSTOPRE_SHIFT ) )
+ /* 0x05100500 */
#if defined(CONFIG_DDR_2T_TIMING)
#define CFG_SDRAM_CFG ( SDRAM_CFG_SREN \
| SDRAM_CFG_SDRAM_TYPE_DDR2 \
@@ -124,9 +124,9 @@
#endif
#define CFG_SDRAM_CFG2 0x00401000;
/* set burst length to 8 for 32-bit data path */
-#define CFG_DDR_MODE ( ( 0x4440 << SDRAM_MODE_ESD_SHIFT ) \
- | ( 0x0232 << SDRAM_MODE_SD_SHIFT ) )
- /* 0x44400232 */
+#define CFG_DDR_MODE ( ( 0x4448 << SDRAM_MODE_ESD_SHIFT ) \
+ | ( 0x0632 << SDRAM_MODE_SD_SHIFT ) )
+ /* 0x44480632 */
#define CFG_DDR_MODE_2 0x8000C000;
#define CFG_DDR_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
diff --git a/include/configs/MPC8315ERDB.h b/include/configs/MPC8315ERDB.h
new file mode 100644
index 0000000..ad2305c
--- /dev/null
+++ b/include/configs/MPC8315ERDB.h
@@ -0,0 +1,547 @@
+/*
+ * Copyright (C) 2007 Freescale Semiconductor, Inc.
+ *
+ * Dave Liu <daveliu@freescale.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#undef DEBUG
+
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_E300 1 /* E300 family */
+#define CONFIG_MPC83XX 1 /* MPC83xx family */
+#define CONFIG_MPC831X 1 /* MPC831x CPU family */
+#define CONFIG_MPC8315 1 /* MPC8315 CPU specific */
+#define CONFIG_MPC8315ERDB 1 /* MPC8315ERDB board specific */
+
+/*
+ * System Clock Setup
+ */
+#define CONFIG_83XX_CLKIN 66666667 /* in Hz */
+#define CONFIG_SYS_CLK_FREQ CONFIG_83XX_CLKIN
+
+/*
+ * Hardware Reset Configuration Word
+ * if CLKIN is 66.66MHz, then
+ * CSB = 133MHz, CORE = 400MHz, DDRC = 266MHz, LBC = 133MHz
+ */
+#define CFG_HRCW_LOW (\
+ HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
+ HRCWL_DDR_TO_SCB_CLK_2X1 |\
+ HRCWL_SVCOD_DIV_2 |\
+ HRCWL_CSB_TO_CLKIN_2X1 |\
+ HRCWL_CORE_TO_CSB_3X1)
+#define CFG_HRCW_HIGH (\
+ HRCWH_PCI_HOST |\
+ HRCWH_PCI1_ARBITER_ENABLE |\
+ HRCWH_CORE_ENABLE |\
+ HRCWH_FROM_0X00000100 |\
+ HRCWH_BOOTSEQ_DISABLE |\
+ HRCWH_SW_WATCHDOG_DISABLE |\
+ HRCWH_ROM_LOC_LOCAL_16BIT |\
+ HRCWH_RL_EXT_LEGACY |\
+ HRCWH_TSEC1M_IN_RGMII |\
+ HRCWH_TSEC2M_IN_RGMII |\
+ HRCWH_BIG_ENDIAN |\
+ HRCWH_LALE_NORMAL)
+
+/*
+ * System IO Config
+ */
+#define CFG_SICRH 0x00000000
+#define CFG_SICRL 0x00000000 /* 3.3V, no delay */
+
+#define CONFIG_BOARD_EARLY_INIT_F /* call board_pre_init */
+
+/*
+ * IMMR new address
+ */
+#define CFG_IMMR 0xE0000000
+
+/*
+ * Arbiter Setup
+ */
+#define CFG_ACR_PIPE_DEP 3 /* Arbiter pipeline depth is 4 */
+#define CFG_ACR_RPTCNT 3 /* Arbiter repeat count is 4 */
+#define CFG_SPCR_TSECEP 3 /* eTSEC emergency priority is highest */
+
+/*
+ * DDR Setup
+ */
+#define CFG_DDR_BASE 0x00000000 /* DDR is system memory */
+#define CFG_SDRAM_BASE CFG_DDR_BASE
+#define CFG_DDR_SDRAM_BASE CFG_DDR_BASE
+#define CFG_DDR_SDRAM_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
+#define CFG_DDRCDR_VALUE ( DDRCDR_EN \
+ | DDRCDR_PZ_LOZ \
+ | DDRCDR_NZ_LOZ \
+ | DDRCDR_ODT \
+ | DDRCDR_Q_DRN )
+ /* 0x7b880001 */
+/*
+ * Manually set up DDR parameters
+ * consist of two chips HY5PS12621BFP-C4 from HYNIX
+ */
+#define CFG_DDR_SIZE 128 /* MB */
+#define CFG_DDR_CS0_BNDS 0x00000007
+#define CFG_DDR_CS0_CONFIG ( CSCONFIG_EN \
+ | 0x00010000 /* ODT_WR to CSn */ \
+ | CSCONFIG_ROW_BIT_13 | CSCONFIG_COL_BIT_10 )
+ /* 0x80010102 */
+#define CFG_DDR_TIMING_3 0x00000000
+#define CFG_DDR_TIMING_0 ( ( 0 << TIMING_CFG0_RWT_SHIFT ) \
+ | ( 0 << TIMING_CFG0_WRT_SHIFT ) \
+ | ( 0 << TIMING_CFG0_RRT_SHIFT ) \
+ | ( 0 << TIMING_CFG0_WWT_SHIFT ) \
+ | ( 2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT ) \
+ | ( 2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT ) \
+ | ( 8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT ) \
+ | ( 2 << TIMING_CFG0_MRS_CYC_SHIFT ) )
+ /* 0x00220802 */
+#define CFG_DDR_TIMING_1 ( ( 3 << TIMING_CFG1_PRETOACT_SHIFT ) \
+ | ( 9 << TIMING_CFG1_ACTTOPRE_SHIFT ) \
+ | ( 3 << TIMING_CFG1_ACTTORW_SHIFT ) \
+ | ( 5 << TIMING_CFG1_CASLAT_SHIFT ) \
+ | ( 6 << TIMING_CFG1_REFREC_SHIFT ) \
+ | ( 2 << TIMING_CFG1_WRREC_SHIFT ) \
+ | ( 2 << TIMING_CFG1_ACTTOACT_SHIFT ) \
+ | ( 2 << TIMING_CFG1_WRTORD_SHIFT ) )
+ /* 0x39356222 */
+#define CFG_DDR_TIMING_2 ( ( 1 << TIMING_CFG2_ADD_LAT_SHIFT ) \
+ | ( 4 << TIMING_CFG2_CPO_SHIFT ) \
+ | ( 2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT ) \
+ | ( 2 << TIMING_CFG2_RD_TO_PRE_SHIFT ) \
+ | ( 2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT ) \
+ | ( 3 << TIMING_CFG2_CKE_PLS_SHIFT ) \
+ | ( 7 << TIMING_CFG2_FOUR_ACT_SHIFT) )
+ /* 0x121048c7 */
+#define CFG_DDR_INTERVAL ( ( 0x0360 << SDRAM_INTERVAL_REFINT_SHIFT ) \
+ | ( 0x0100 << SDRAM_INTERVAL_BSTOPRE_SHIFT ) )
+ /* 0x03600100 */
+#define CFG_DDR_SDRAM_CFG ( SDRAM_CFG_SREN \
+ | SDRAM_CFG_SDRAM_TYPE_DDR2 \
+ | SDRAM_CFG_32_BE )
+ /* 0x43080000 */
+#define CFG_DDR_SDRAM_CFG2 0x00401000 /* 1 posted refresh */
+#define CFG_DDR_MODE ( ( 0x0448 << SDRAM_MODE_ESD_SHIFT ) \
+ | ( 0x0232 << SDRAM_MODE_SD_SHIFT ) )
+ /* ODT 150ohm CL=3, AL=1 on SDRAM */
+#define CFG_DDR_MODE2 0x00000000
+
+/*
+ * Memory test
+ */
+#undef CFG_DRAM_TEST /* memory test, takes time */
+#define CFG_MEMTEST_START 0x00040000 /* memtest region */
+#define CFG_MEMTEST_END 0x00140000
+
+/*
+ * The reserved memory
+ */
+#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */
+
+#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
+#define CFG_RAMBOOT
+#else
+#undef CFG_RAMBOOT
+#endif
+
+#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
+#define CFG_MALLOC_LEN (512 * 1024) /* Reserved for malloc */
+
+/*
+ * Initial RAM Base Address Setup
+ */
+#define CFG_INIT_RAM_LOCK 1
+#define CFG_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */
+#define CFG_INIT_RAM_END 0x1000 /* End of used area in RAM */
+#define CFG_GBL_DATA_SIZE 0x100 /* num bytes initial data */
+#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+
+/*
+ * Local Bus Configuration & Clock Setup
+ */
+#define CFG_LCRR (LCRR_DBYP | LCRR_CLKDIV_2)
+#define CFG_LBC_LBCR 0x00040000
+
+/*
+ * FLASH on the Local Bus
+ */
+#define CFG_FLASH_CFI /* use the Common Flash Interface */
+#define CFG_FLASH_CFI_DRIVER /* use the CFI driver */
+#define CFG_FLASH_CFI_WIDTH FLASH_CFI_16BIT
+
+#define CFG_FLASH_BASE 0xFE000000 /* FLASH base address */
+#define CFG_FLASH_SIZE 8 /* FLASH size is 8M */
+
+#define CFG_LBLAWBAR0_PRELIM CFG_FLASH_BASE /* Window base at flash base */
+#define CFG_LBLAWAR0_PRELIM 0x80000016 /* 8MB window size */
+
+#define CFG_BR0_PRELIM ( CFG_FLASH_BASE /* Flash Base address */ \
+ | (2 << BR_PS_SHIFT) /* 16 bit port size */ \
+ | BR_V ) /* valid */
+#define CFG_OR0_PRELIM ( (~(CFG_FLASH_SIZE - 1) << 20) \
+ | OR_UPM_XAM \
+ | OR_GPCM_CSNT \
+ | OR_GPCM_ACS_0b11 \
+ | OR_GPCM_XACS \
+ | OR_GPCM_SCY_15 \
+ | OR_GPCM_TRLX \
+ | OR_GPCM_EHTR \
+ | OR_GPCM_EAD )
+
+#define CFG_MAX_FLASH_BANKS 1 /* number of banks */
+#define CFG_MAX_FLASH_SECT 135 /* 127 64KB sectors and 8 8KB top sectors per device */
+
+#undef CFG_FLASH_CHECKSUM
+#define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
+#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
+
+/*
+ * NAND Flash on the Local Bus
+ */
+#define CFG_NAND_BASE 0xE0600000 /* 0xE0600000 */
+#define CFG_MAX_NAND_DEVICE 1
+#define NAND_MAX_CHIPS 1
+#define CONFIG_MTD_NAND_VERIFY_WRITE
+
+#define CFG_BR1_PRELIM ( CFG_NAND_BASE \
+ | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \
+ | BR_PS_8 /* Port Size = 8 bit */ \
+ | BR_MS_FCM /* MSEL = FCM */ \
+ | BR_V ) /* valid */
+#define CFG_OR1_PRELIM ( 0xFFFF8000 /* length 32K */ \
+ | OR_FCM_CSCT \
+ | OR_FCM_CST \
+ | OR_FCM_CHT \
+ | OR_FCM_SCY_1 \
+ | OR_FCM_TRLX \
+ | OR_FCM_EHTR )
+ /* 0xFFFF8396 */
+
+#define CFG_LBLAWBAR1_PRELIM CFG_NAND_BASE
+#define CFG_LBLAWAR1_PRELIM 0x8000000E /* 32KB */
+
+/*
+ * Serial Port
+ */
+#define CONFIG_CONS_INDEX 1
+#undef CONFIG_SERIAL_SOFTWARE_FIFO
+#define CFG_NS16550
+#define CFG_NS16550_SERIAL
+#define CFG_NS16550_REG_SIZE 1
+#define CFG_NS16550_CLK get_bus_freq(0)
+
+#define CFG_BAUDRATE_TABLE \
+ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
+
+#define CFG_NS16550_COM1 (CFG_IMMR+0x4500)
+#define CFG_NS16550_COM2 (CFG_IMMR+0x4600)
+
+/* Use the HUSH parser */
+#define CFG_HUSH_PARSER
+#ifdef CFG_HUSH_PARSER
+#define CFG_PROMPT_HUSH_PS2 "> "
+#endif
+
+/* Pass open firmware flat tree */
+#define CONFIG_OF_LIBFDT 1
+#define CONFIG_OF_BOARD_SETUP 1
+#define CONFIG_OF_STDOUT_VIA_ALIAS 1
+
+/* I2C */
+#define CONFIG_HARD_I2C /* I2C with hardware support */
+#define CONFIG_FSL_I2C
+#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
+#define CFG_I2C_SLAVE 0x7F
+#define CFG_I2C_NOPROBES {0x51} /* Don't probe these addrs */
+#define CFG_I2C_OFFSET 0x3000
+#define CFG_I2C2_OFFSET 0x3100
+
+/*
+ * Board info - revision and where boot from
+ */
+#define CFG_I2C_PCF8574A_ADDR 0x39
+
+/*
+ * Config on-board RTC
+ */
+#define CONFIG_RTC_DS1337 /* ds1339 on board, use ds1337 rtc via i2c */
+#define CFG_I2C_RTC_ADDR 0x68 /* at address 0x68 */
+
+/*
+ * General PCI
+ * Addresses are mapped 1-1.
+ */
+#define CFG_PCI_MEM_BASE 0x80000000
+#define CFG_PCI_MEM_PHYS CFG_PCI_MEM_BASE
+#define CFG_PCI_MEM_SIZE 0x10000000 /* 256M */
+#define CFG_PCI_MMIO_BASE 0x90000000
+#define CFG_PCI_MMIO_PHYS CFG_PCI_MMIO_BASE
+#define CFG_PCI_MMIO_SIZE 0x10000000 /* 256M */
+#define CFG_PCI_IO_BASE 0xE0300000
+#define CFG_PCI_IO_PHYS 0xE0300000
+#define CFG_PCI_IO_SIZE 0x100000 /* 1M */
+
+#define CFG_PCI_SLV_MEM_LOCAL CFG_SDRAM_BASE
+#define CFG_PCI_SLV_MEM_BUS 0x00000000
+#define CFG_PCI_SLV_MEM_SIZE 0x80000000
+
+#define CONFIG_PCI
+#define CONFIG_83XX_GENERIC_PCI 1 /* Use generic PCI setup */
+
+#define CONFIG_NET_MULTI
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
+
+#define CONFIG_EEPRO100
+#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
+#define CFG_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */
+
+#ifndef CONFIG_NET_MULTI
+#define CONFIG_NET_MULTI 1
+#endif
+
+/*
+ * TSEC
+ */
+#define CONFIG_TSEC_ENET /* TSEC ethernet support */
+#define CFG_TSEC1_OFFSET 0x24000
+#define CFG_TSEC1 (CFG_IMMR+CFG_TSEC1_OFFSET)
+#define CFG_TSEC2_OFFSET 0x25000
+#define CFG_TSEC2 (CFG_IMMR+CFG_TSEC2_OFFSET)
+
+/*
+ * TSEC ethernet configuration
+ */
+#define CONFIG_MII 1 /* MII PHY management */
+#define CONFIG_TSEC1 1
+#define CONFIG_TSEC1_NAME "eTSEC0"
+#define CONFIG_TSEC2 1
+#define CONFIG_TSEC2_NAME "eTSEC1"
+#define TSEC1_PHY_ADDR 0
+#define TSEC2_PHY_ADDR 1
+#define TSEC1_PHYIDX 0
+#define TSEC2_PHYIDX 0
+#define TSEC1_FLAGS TSEC_GIGABIT
+#define TSEC2_FLAGS TSEC_GIGABIT
+
+/* Options are: eTSEC[0-1] */
+#define CONFIG_ETHPRIME "eTSEC1"
+
+/*
+ * Environment
+ */
+#ifndef CFG_RAMBOOT
+ #define CFG_ENV_IS_IN_FLASH 1
+ #define CFG_ENV_ADDR (CFG_MONITOR_BASE + CFG_MONITOR_LEN)
+ #define CFG_ENV_SECT_SIZE 0x10000 /* 64K(one sector) for env */
+ #define CFG_ENV_SIZE 0x2000
+#else
+ #define CFG_NO_FLASH 1 /* Flash is not usable now */
+ #define CFG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
+ #define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000)
+ #define CFG_ENV_SIZE 0x2000
+#endif
+
+#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
+#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_PCI
+
+#if defined(CFG_RAMBOOT)
+ #undef CONFIG_CMD_ENV
+ #undef CONFIG_CMD_LOADS
+#endif
+
+#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
+
+#undef CONFIG_WATCHDOG /* watchdog disabled */
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP /* undef to save memory */
+#define CFG_LOAD_ADDR 0x2000000 /* default load address */
+#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+
+#if defined(CONFIG_CMD_KGDB)
+ #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+ #define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+#define CFG_HZ 1000 /* decrementer freq: 1ms ticks */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+
+/*
+ * Core HID Setup
+ */
+#define CFG_HID0_INIT 0x000000000
+#define CFG_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \
+ HID0_ENABLE_DYNAMIC_POWER_MANAGMENT)
+#define CFG_HID2 HID2_HBE
+
+/*
+ * MMU Setup
+ */
+
+/* DDR: cache cacheable */
+#define CFG_IBAT0L (CFG_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CFG_IBAT0U (CFG_SDRAM_BASE | BATU_BL_128M | BATU_VS | BATU_VP)
+#define CFG_DBAT0L CFG_IBAT0L
+#define CFG_DBAT0U CFG_IBAT0U
+
+/* IMMRBAR, PCI IO and NAND: cache-inhibit and guarded */
+#define CFG_IBAT1L (CFG_IMMR | BATL_PP_10 | \
+ BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_IBAT1U (CFG_IMMR | BATU_BL_8M | BATU_VS | BATU_VP)
+#define CFG_DBAT1L CFG_IBAT1L
+#define CFG_DBAT1U CFG_IBAT1U
+
+/* FLASH: icache cacheable, but dcache-inhibit and guarded */
+#define CFG_IBAT2L (CFG_FLASH_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CFG_IBAT2U (CFG_FLASH_BASE | BATU_BL_8M | BATU_VS | BATU_VP)
+#define CFG_DBAT2L (CFG_FLASH_BASE | BATL_PP_10 | \
+ BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_DBAT2U CFG_IBAT2U
+
+/* Stack in dcache: cacheable, no memory coherence */
+#define CFG_IBAT3L (CFG_INIT_RAM_ADDR | BATL_PP_10)
+#define CFG_IBAT3U (CFG_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
+#define CFG_DBAT3L CFG_IBAT3L
+#define CFG_DBAT3U CFG_IBAT3U
+
+/* PCI MEM space: cacheable */
+#define CFG_IBAT4L (CFG_PCI_MEM_PHYS | BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CFG_IBAT4U (CFG_PCI_MEM_PHYS | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CFG_DBAT4L CFG_IBAT4L
+#define CFG_DBAT4U CFG_IBAT4U
+
+/* PCI MMIO space: cache-inhibit and guarded */
+#define CFG_IBAT5L (CFG_PCI_MMIO_PHYS | BATL_PP_10 | \
+ BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_IBAT5U (CFG_PCI_MMIO_PHYS | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CFG_DBAT5L CFG_IBAT5L
+#define CFG_DBAT5U CFG_IBAT5U
+
+#define CFG_IBAT6L 0
+#define CFG_IBAT6U 0
+#define CFG_DBAT6L CFG_IBAT6L
+#define CFG_DBAT6U CFG_IBAT6U
+
+#define CFG_IBAT7L 0
+#define CFG_IBAT7U 0
+#define CFG_DBAT7L CFG_IBAT7L
+#define CFG_DBAT7U CFG_IBAT7U
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
+
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
+#endif
+
+/*
+ * Environment Configuration
+ */
+
+#define CONFIG_ENV_OVERWRITE
+
+#if defined(CONFIG_TSEC_ENET)
+#define CONFIG_HAS_ETH0
+#define CONFIG_ETHADDR 04:00:00:00:00:0A
+#define CONFIG_HAS_ETH1
+#define CONFIG_ETH1ADDR 04:00:00:00:00:0B
+#endif
+
+#define CONFIG_BAUDRATE 115200
+
+#define CONFIG_LOADADDR 200000 /* default location for tftp and bootm */
+
+#define CONFIG_BOOTDELAY 6 /* -1 disables auto-boot */
+#undef CONFIG_BOOTARGS /* the boot command will set bootargs */
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "netdev=eth0\0" \
+ "consoledev=ttyS0\0" \
+ "ramdiskaddr=1000000\0" \
+ "ramdiskfile=ramfs.83xx\0" \
+ "fdtaddr=400000\0" \
+ "fdtfile=mpc8315erdb.dtb\0" \
+ ""
+
+#define CONFIG_NFSBOOTCOMMAND \
+ "setenv bootargs root=/dev/nfs rw " \
+ "nfsroot=$serverip:$rootpath " \
+ "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr - $fdtaddr"
+
+#define CONFIG_RAMBOOTCOMMAND \
+ "setenv bootargs root=/dev/ram rw " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "tftp $ramdiskaddr $ramdiskfile;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr $ramdiskaddr $fdtaddr"
+
+
+#define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND
+
+#endif /* __CONFIG_H */
diff --git a/include/configs/MPC8323ERDB.h b/include/configs/MPC8323ERDB.h
index 4ea8709..295e785 100644
--- a/include/configs/MPC8323ERDB.h
+++ b/include/configs/MPC8323ERDB.h
@@ -321,7 +321,7 @@
* QE UEC ethernet configuration
*/
#define CONFIG_UEC_ETH
-#define CONFIG_ETHPRIME "Freescale GETH"
+#define CONFIG_ETHPRIME "FSL UEC0"
#define CONFIG_UEC_ETH1 /* ETH3 */
diff --git a/include/configs/MPC832XEMDS.h b/include/configs/MPC832XEMDS.h
index 25ac58c..6c0e68a 100644
--- a/include/configs/MPC832XEMDS.h
+++ b/include/configs/MPC832XEMDS.h
@@ -377,7 +377,7 @@
* QE UEC ethernet configuration
*/
#define CONFIG_UEC_ETH
-#define CONFIG_ETHPRIME "Freescale GETH"
+#define CONFIG_ETHPRIME "FSL UEC0"
#define CONFIG_UEC_ETH1 /* ETH3 */
diff --git a/include/configs/MPC8360EMDS.h b/include/configs/MPC8360EMDS.h
index fdacb90..168ca2a 100644
--- a/include/configs/MPC8360EMDS.h
+++ b/include/configs/MPC8360EMDS.h
@@ -405,7 +405,7 @@
* QE UEC ethernet configuration
*/
#define CONFIG_UEC_ETH
-#define CONFIG_ETHPRIME "Freescale GETH"
+#define CONFIG_ETHPRIME "FSL UEC0"
#define CONFIG_PHY_MODE_NEED_CHANGE
#define CONFIG_UEC_ETH1 /* GETH1 */
@@ -466,6 +466,7 @@
#define CONFIG_CMD_PING
#define CONFIG_CMD_I2C
#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_SDRAM
#if defined(CONFIG_PCI)
#define CONFIG_CMD_PCI
diff --git a/include/configs/MPC8360ERDK.h b/include/configs/MPC8360ERDK.h
index 0f6f8f1..83a4b1e 100644
--- a/include/configs/MPC8360ERDK.h
+++ b/include/configs/MPC8360ERDK.h
@@ -282,7 +282,7 @@
* QE UEC ethernet configuration
*/
#define CONFIG_UEC_ETH
-#define CONFIG_ETHPRIME "Freescale GETH"
+#define CONFIG_ETHPRIME "FSL UEC0"
#define CONFIG_UEC_ETH1 /* GETH1 */
@@ -387,15 +387,6 @@
#define CFG_HID2 HID2_HBE
/*
- * Cache Config
- */
-#define CFG_DCACHE_SIZE 32768
-#define CFG_CACHELINE_SIZE 32
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value */
-#endif
-
-/*
* MMU Setup
*/
diff --git a/include/configs/MPC837XERDB.h b/include/configs/MPC837XERDB.h
new file mode 100644
index 0000000..2da4f29
--- /dev/null
+++ b/include/configs/MPC837XERDB.h
@@ -0,0 +1,596 @@
+/*
+ * Copyright (C) 2007 Freescale Semiconductor, Inc.
+ * Kevin Lam <kevin.lam@freescale.com>
+ * Joe D'Abbraccio <joe.d'abbraccio@freescale.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_E300 1 /* E300 family */
+#define CONFIG_MPC83XX 1 /* MPC83XX family */
+#define CONFIG_MPC837X 1 /* MPC837X CPU specific */
+#define CONFIG_MPC837XERDB 1
+
+#define CONFIG_PCI 1
+
+/*
+ * System Clock Setup
+ */
+#ifdef CONFIG_PCISLAVE
+#define CONFIG_83XX_PCICLK 66666667 /* in HZ */
+#else
+#define CONFIG_83XX_CLKIN 66666667 /* in Hz */
+#define CONFIG_83XX_GENERIC_PCI 1
+#endif
+
+#ifndef CONFIG_SYS_CLK_FREQ
+#define CONFIG_SYS_CLK_FREQ CONFIG_83XX_CLKIN
+#endif
+
+/*
+ * Hardware Reset Configuration Word
+ */
+#define CFG_HRCW_LOW (\
+ HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
+ HRCWL_DDR_TO_SCB_CLK_1X1 |\
+ HRCWL_SVCOD_DIV_2 |\
+ HRCWL_CSB_TO_CLKIN_5X1 |\
+ HRCWL_CORE_TO_CSB_2X1)
+
+#ifdef CONFIG_PCISLAVE
+#define CFG_HRCW_HIGH (\
+ HRCWH_PCI_AGENT |\
+ HRCWH_PCI1_ARBITER_DISABLE |\
+ HRCWH_CORE_ENABLE |\
+ HRCWH_FROM_0XFFF00100 |\
+ HRCWH_BOOTSEQ_DISABLE |\
+ HRCWH_SW_WATCHDOG_DISABLE |\
+ HRCWH_ROM_LOC_LOCAL_16BIT |\
+ HRCWH_RL_EXT_LEGACY |\
+ HRCWH_TSEC1M_IN_RGMII |\
+ HRCWH_TSEC2M_IN_RGMII |\
+ HRCWH_BIG_ENDIAN |\
+ HRCWH_LDP_CLEAR)
+#else
+#define CFG_HRCW_HIGH (\
+ HRCWH_PCI_HOST |\
+ HRCWH_PCI1_ARBITER_ENABLE |\
+ HRCWH_CORE_ENABLE |\
+ HRCWH_FROM_0X00000100 |\
+ HRCWH_BOOTSEQ_DISABLE |\
+ HRCWH_SW_WATCHDOG_DISABLE |\
+ HRCWH_ROM_LOC_LOCAL_16BIT |\
+ HRCWH_RL_EXT_LEGACY |\
+ HRCWH_TSEC1M_IN_RGMII |\
+ HRCWH_TSEC2M_IN_RGMII |\
+ HRCWH_BIG_ENDIAN |\
+ HRCWH_LDP_CLEAR)
+#endif
+
+/* System performance - define the value i.e. CFG_XXX
+*/
+
+/* Arbiter Configuration Register */
+#define CFG_ACR_PIPE_DEP 3 /* Arbiter pipeline depth (0-3) */
+#define CFG_ACR_RPTCNT 3 /* Arbiter repeat count (0-7) */
+
+/* System Priority Control Regsiter */
+#define CFG_SPCR_TSECEP 3 /* eTSEC1&2 emergency priority (0-3) */
+
+/* System Clock Configuration Register */
+#define CFG_SCCR_TSEC1CM 1 /* eTSEC1 clock mode (0-3) */
+#define CFG_SCCR_TSEC2CM 1 /* eTSEC2 clock mode (0-3) */
+#define CFG_SCCR_SATACM SCCR_SATACM_1 /* SATA1-4 clock mode (0-3) */
+
+/*
+ * System IO Config
+ */
+#define CFG_SICRH 0x08200000
+#define CFG_SICRL 0x00000000
+
+/*
+ * Output Buffer Impedance
+ */
+#define CFG_OBIR 0x30100000
+
+/*
+ * IMMR new address
+ */
+#define CFG_IMMR 0xE0000000
+
+/*
+ * DDR Setup
+ */
+#define CFG_DDR_BASE 0x00000000 /* DDR is system memory */
+#define CFG_SDRAM_BASE CFG_DDR_BASE
+#define CFG_DDR_SDRAM_BASE CFG_DDR_BASE
+#define CFG_DDR_SDRAM_CLK_CNTL 0x03000000
+#define CFG_83XX_DDR_USES_CS0
+
+#define CFG_DDRCDR_VALUE (DDRCDR_DHC_EN | DDRCDR_ODT | DDRCDR_Q_DRN)
+
+#undef CONFIG_DDR_ECC /* support DDR ECC function */
+#undef CONFIG_DDR_ECC_CMD /* Use DDR ECC user commands */
+
+#undef CONFIG_NEVER_ASSERT_ODT_TO_CPU /* Never assert ODT to internal IOs */
+
+/*
+ * Manually set up DDR parameters
+ */
+#define CFG_DDR_SIZE 256 /* MB */
+#define CFG_DDR_CS0_BNDS 0x0000000f
+#define CFG_DDR_CS0_CONFIG (CSCONFIG_EN | CSCONFIG_ODT_WR_ACS \
+ | CSCONFIG_ROW_BIT_13 | CSCONFIG_COL_BIT_10)
+
+#define CFG_DDR_TIMING_3 0x00000000
+#define CFG_DDR_TIMING_0 ((0 << TIMING_CFG0_RWT_SHIFT) \
+ | (0 << TIMING_CFG0_WRT_SHIFT) \
+ | (0 << TIMING_CFG0_RRT_SHIFT) \
+ | (0 << TIMING_CFG0_WWT_SHIFT) \
+ | (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \
+ | (6 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \
+ | (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \
+ | (2 << TIMING_CFG0_MRS_CYC_SHIFT))
+ /* 0x00220802 */
+ /* 0x00260802 */ /* DDR400 */
+#define CFG_DDR_TIMING_1 ((3 << TIMING_CFG1_PRETOACT_SHIFT) \
+ | (9 << TIMING_CFG1_ACTTOPRE_SHIFT) \
+ | (3 << TIMING_CFG1_ACTTORW_SHIFT) \
+ | (7 << TIMING_CFG1_CASLAT_SHIFT) \
+ | (13 << TIMING_CFG1_REFREC_SHIFT) \
+ | (3 << TIMING_CFG1_WRREC_SHIFT) \
+ | (2 << TIMING_CFG1_ACTTOACT_SHIFT) \
+ | (2 << TIMING_CFG1_WRTORD_SHIFT))
+ /* 0x3935d322 */
+ /* 0x3937d322 */
+#define CFG_DDR_TIMING_2 0x02984cc8
+
+#define CFG_DDR_INTERVAL ((1545 << SDRAM_INTERVAL_REFINT_SHIFT) \
+ | (256 << SDRAM_INTERVAL_BSTOPRE_SHIFT))
+ /* 0x06090100 */
+
+#if defined(CONFIG_DDR_2T_TIMING)
+#define CFG_DDR_SDRAM_CFG (SDRAM_CFG_SREN \
+ | 3 << SDRAM_CFG_SDRAM_TYPE_SHIFT \
+ | SDRAM_CFG_2T_EN \
+ | SDRAM_CFG_DBW_32)
+#else
+#define CFG_DDR_SDRAM_CFG (SDRAM_CFG_SREN \
+ | 3 << SDRAM_CFG_SDRAM_TYPE_SHIFT)
+ /* 0x43000000 */
+#endif
+#define CFG_DDR_SDRAM_CFG2 0x00001000 /* 1 posted refresh */
+#define CFG_DDR_MODE ((0x0440 << SDRAM_MODE_ESD_SHIFT) \
+ | (0x0442 << SDRAM_MODE_SD_SHIFT))
+ /* 0x04400442 */ /* DDR400 */
+#define CFG_DDR_MODE2 0x00000000;
+
+/*
+ * Memory test
+ */
+#undef CFG_DRAM_TEST /* memory test, takes time */
+#define CFG_MEMTEST_START 0x00040000 /* memtest region */
+#define CFG_MEMTEST_END 0x0ef70010
+
+/*
+ * The reserved memory
+ */
+#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */
+
+#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
+#define CFG_RAMBOOT
+#else
+#undef CFG_RAMBOOT
+#endif
+
+#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
+#define CFG_MALLOC_LEN (512 * 1024) /* Reserved for malloc */
+
+/*
+ * Initial RAM Base Address Setup
+ */
+#define CFG_INIT_RAM_LOCK 1
+#define CFG_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */
+#define CFG_INIT_RAM_END 0x1000 /* End of used area in RAM */
+#define CFG_GBL_DATA_SIZE 0x100 /* num bytes initial data */
+#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+
+/*
+ * Local Bus Configuration & Clock Setup
+ */
+#define CFG_LCRR (LCRR_DBYP | LCRR_CLKDIV_8)
+#define CFG_LBC_LBCR 0x00000000
+
+/*
+ * FLASH on the Local Bus
+ */
+#define CFG_FLASH_CFI /* use the Common Flash Interface */
+#define CFG_FLASH_CFI_DRIVER /* use the CFI driver */
+#define CFG_FLASH_BASE 0xFE000000 /* FLASH base address */
+#define CFG_FLASH_SIZE 8 /* max FLASH size is 32M */
+
+#define CFG_FLASH_EMPTY_INFO /* display empty sectors */
+#define CFG_FLASH_USE_BUFFER_WRITE /* buffer up multiple bytes */
+
+#define CFG_LBLAWBAR0_PRELIM CFG_FLASH_BASE /* Window base at flash base */
+#define CFG_LBLAWAR0_PRELIM 0x80000016 /* 8 MB window size */
+
+#define CFG_BR0_PRELIM (CFG_FLASH_BASE | /* Flash Base address */ \
+ (2 << BR_PS_SHIFT) | /* 16 bit port size */ \
+ BR_V) /* valid */
+#define CFG_OR0_PRELIM (0xFF800000 /* 8 MByte */ \
+ | OR_GPCM_XACS \
+ | OR_GPCM_SCY_9 \
+ | OR_GPCM_EHTR \
+ | OR_GPCM_EAD)
+ /* 0xFF806FF7 TODO SLOW 8 MB flash size */
+
+#define CFG_MAX_FLASH_BANKS 1 /* number of banks */
+#define CFG_MAX_FLASH_SECT 256 /* max sectors per device */
+
+#undef CFG_FLASH_CHECKSUM
+#define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
+#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
+
+#define CFG_VSC7385_BASE 0xF0000000
+
+/* VSC7385 Gigabit Switch support */
+#define CONFIG_VSC7385_ENET
+#define CFG_BR2_PRELIM 0xf0000801 /* Base address */
+#define CFG_OR2_PRELIM 0xfffe09ff /* 128K bytes*/
+#define CFG_LBLAWBAR2_PRELIM CFG_VSC7385_BASE /* Access Base */
+#define CFG_LBLAWAR2_PRELIM 0x80000010 /* Access Size 128K */
+
+/*
+ * Serial Port
+ */
+#define CONFIG_CONS_INDEX 1
+#undef CONFIG_SERIAL_SOFTWARE_FIFO
+#define CFG_NS16550
+#define CFG_NS16550_SERIAL
+#define CFG_NS16550_REG_SIZE 1
+#define CFG_NS16550_CLK get_bus_freq(0)
+
+#define CFG_BAUDRATE_TABLE \
+ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
+
+#define CFG_NS16550_COM1 (CFG_IMMR+0x4500)
+#define CFG_NS16550_COM2 (CFG_IMMR+0x4600)
+
+/* Use the HUSH parser */
+#define CFG_HUSH_PARSER
+#ifdef CFG_HUSH_PARSER
+#define CFG_PROMPT_HUSH_PS2 "> "
+#endif
+
+/* Pass open firmware flat tree */
+#define CONFIG_OF_LIBFDT 1
+#define CONFIG_OF_BOARD_SETUP 1
+
+/* I2C */
+#define CONFIG_HARD_I2C /* I2C with hardware support */
+#undef CONFIG_SOFT_I2C /* I2C bit-banged */
+#define CONFIG_FSL_I2C
+#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
+#define CFG_I2C_SLAVE 0x7F
+#define CFG_I2C_NOPROBES {0x51} /* Don't probe these addrs */
+#define CFG_I2C_OFFSET 0x3000
+#define CFG_I2C2_OFFSET 0x3100
+
+/*
+ * Config on-board RTC
+ */
+#define CONFIG_RTC_DS1374 /* use ds1374 rtc via i2c */
+#define CFG_I2C_RTC_ADDR 0x68 /* at address 0x68 */
+
+/*
+ * General PCI
+ * Addresses are mapped 1-1.
+ */
+#define CFG_PCI_MEM_BASE 0x80000000
+#define CFG_PCI_MEM_PHYS CFG_PCI_MEM_BASE
+#define CFG_PCI_MEM_SIZE 0x10000000 /* 256M */
+#define CFG_PCI_MMIO_BASE 0x90000000
+#define CFG_PCI_MMIO_PHYS CFG_PCI_MMIO_BASE
+#define CFG_PCI_MMIO_SIZE 0x10000000 /* 256M */
+#define CFG_PCI_IO_BASE 0xE0300000
+#define CFG_PCI_IO_PHYS 0xE0300000
+#define CFG_PCI_IO_SIZE 0x100000 /* 1M */
+
+#define CFG_PCI_SLV_MEM_LOCAL CFG_SDRAM_BASE
+#define CFG_PCI_SLV_MEM_BUS 0x00000000
+#define CFG_PCI_SLV_MEM_SIZE 0x80000000
+
+#ifdef CONFIG_PCI
+#define CONFIG_NET_MULTI
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
+
+#undef CONFIG_EEPRO100
+#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
+#define CFG_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */
+#endif /* CONFIG_PCI */
+
+#ifndef CONFIG_NET_MULTI
+#define CONFIG_NET_MULTI 1
+#endif
+
+/*
+ * TSEC
+ */
+#define CONFIG_TSEC_ENET /* TSEC ethernet support */
+#define CFG_TSEC1_OFFSET 0x24000
+#define CFG_TSEC1 (CFG_IMMR+CFG_TSEC1_OFFSET)
+#define CFG_TSEC2_OFFSET 0x25000
+#define CFG_TSEC2 (CFG_IMMR+CFG_TSEC2_OFFSET)
+
+/*
+ * TSEC ethernet configuration
+ */
+#define CONFIG_GMII 1 /* MII PHY management */
+#define CONFIG_TSEC1 1
+#define CONFIG_TSEC1_NAME "TSEC0"
+#define CONFIG_TSEC2 1
+#define CONFIG_TSEC2_NAME "TSEC1"
+#define TSEC1_PHY_ADDR 2
+#define TSEC2_PHY_ADDR 0x1c
+#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
+#define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
+#define TSEC1_PHYIDX 0
+#define TSEC2_PHYIDX 0
+
+
+/* Options are: TSEC[0-1] */
+#define CONFIG_ETHPRIME "TSEC0"
+
+/*
+ * Environment
+ */
+#ifndef CFG_RAMBOOT
+ #define CFG_ENV_IS_IN_FLASH 1
+ #define CFG_ENV_ADDR (CFG_MONITOR_BASE+CFG_MONITOR_LEN)
+ #define CFG_ENV_SECT_SIZE 0x10000 /* 64K (one sector) for env */
+ #define CFG_ENV_SIZE 0x4000
+#else
+ #define CFG_NO_FLASH 1 /* Flash is not usable now */
+ #define CFG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
+ #define CFG_ENV_ADDR (CFG_MONITOR_BASE-0x1000)
+ #define CFG_ENV_SIZE 0x2000
+#endif
+
+#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
+#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_DATE
+
+#if defined(CONFIG_PCI)
+#define CONFIG_CMD_PCI
+#endif
+
+#if defined(CFG_RAMBOOT)
+#undef CONFIG_CMD_ENV
+#undef CONFIG_CMD_LOADS
+#endif
+
+#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
+
+#undef CONFIG_WATCHDOG /* watchdog disabled */
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP /* undef to save memory */
+#define CFG_LOAD_ADDR 0x2000000 /* default load address */
+#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+
+#if defined(CONFIG_CMD_KGDB)
+ #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+ #define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+#define CFG_HZ 1000 /* decrementer freq: 1ms ticks */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+
+/*
+ * Core HID Setup
+ */
+#define CFG_HID0_INIT 0x000000000
+#define CFG_HID0_FINAL HID0_ENABLE_MACHINE_CHECK
+#define CFG_HID2 HID2_HBE
+
+/*
+ * MMU Setup
+ */
+
+/* DDR: cache cacheable */
+#define CFG_SDRAM_LOWER CFG_SDRAM_BASE
+#define CFG_SDRAM_UPPER (CFG_SDRAM_BASE + 0x10000000)
+
+#define CFG_IBAT0L (CFG_SDRAM_LOWER | BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CFG_IBAT0U (CFG_SDRAM_LOWER | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CFG_DBAT0L CFG_IBAT0L
+#define CFG_DBAT0U CFG_IBAT0U
+
+#define CFG_IBAT1L (CFG_SDRAM_UPPER | BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CFG_IBAT1U (CFG_SDRAM_UPPER | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CFG_DBAT1L CFG_IBAT1L
+#define CFG_DBAT1U CFG_IBAT1U
+
+/* IMMRBAR, PCI IO and NAND: cache-inhibit and guarded */
+#define CFG_IBAT2L (CFG_IMMR | BATL_PP_10 | \
+ BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_IBAT2U (CFG_IMMR | BATU_BL_8M | BATU_VS | BATU_VP)
+#define CFG_DBAT2L CFG_IBAT2L
+#define CFG_DBAT2U CFG_IBAT2U
+
+/* L2 Switch: cache-inhibit and guarded */
+#define CFG_IBAT3L (CFG_VSC7385_BASE | BATL_PP_10 | \
+ BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_IBAT3U (CFG_VSC7385_BASE | BATU_BL_128K | BATU_VS | BATU_VP)
+#define CFG_DBAT3L CFG_IBAT3L
+#define CFG_DBAT3U CFG_IBAT3U
+
+/* FLASH: icache cacheable, but dcache-inhibit and guarded */
+#define CFG_IBAT4L (CFG_FLASH_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CFG_IBAT4U (CFG_FLASH_BASE | BATU_BL_32M | BATU_VS | BATU_VP)
+#define CFG_DBAT4L (CFG_FLASH_BASE | BATL_PP_10 | \
+ BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_DBAT4U CFG_IBAT4U
+
+/* Stack in dcache: cacheable, no memory coherence */
+#define CFG_IBAT5L (CFG_INIT_RAM_ADDR | BATL_PP_10)
+#define CFG_IBAT5U (CFG_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
+#define CFG_DBAT5L CFG_IBAT5L
+#define CFG_DBAT5U CFG_IBAT5U
+
+#ifdef CONFIG_PCI
+/* PCI MEM space: cacheable */
+#define CFG_IBAT6L (CFG_PCI_MEM_PHYS | BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CFG_IBAT6U (CFG_PCI_MEM_PHYS | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CFG_DBAT6L CFG_IBAT6L
+#define CFG_DBAT6U CFG_IBAT6U
+/* PCI MMIO space: cache-inhibit and guarded */
+#define CFG_IBAT7L (CFG_PCI_MMIO_PHYS | BATL_PP_10 | \
+ BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_IBAT7U (CFG_PCI_MMIO_PHYS | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CFG_DBAT7L CFG_IBAT7L
+#define CFG_DBAT7U CFG_IBAT7U
+#else
+#define CFG_IBAT6L (0)
+#define CFG_IBAT6U (0)
+#define CFG_IBAT7L (0)
+#define CFG_IBAT7U (0)
+#define CFG_DBAT6L CFG_IBAT6L
+#define CFG_DBAT6U CFG_IBAT6U
+#define CFG_DBAT7L CFG_IBAT7L
+#define CFG_DBAT7U CFG_IBAT7U
+#endif
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
+
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
+#endif
+
+/*
+ * Environment Configuration
+ */
+#define CONFIG_ENV_OVERWRITE
+
+#define CONFIG_HAS_ETH0 /* add support for "ethaddr" */
+#define CONFIG_ETHADDR 00:04:9f:ef:04:01
+#define CONFIG_HAS_ETH1 /* add support for "eth1addr" */
+#define CONFIG_ETH1ADDR 00:04:9f:ef:04:02
+
+#define CONFIG_IPADDR 10.0.0.2
+#define CONFIG_SERVERIP 10.0.0.1
+#define CONFIG_GATEWAYIP 10.0.0.1
+#define CONFIG_NETMASK 255.0.0.0
+#define CONFIG_NETDEV eth1
+
+#define CONFIG_HOSTNAME mpc837x_rdb
+#define CONFIG_ROOTPATH /nfsroot
+#define CONFIG_RAMDISKFILE rootfs.ext2.gz.uboot
+#define CONFIG_BOOTFILE uImage
+#define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */
+#define CONFIG_FDTFILE mpc837x_rdb.dtb
+
+#define CONFIG_LOADADDR 200000 /* default location for tftp and bootm */
+#define CONFIG_BOOTDELAY -1 /* -1 disables auto-boot */
+#define CONFIG_BAUDRATE 115200
+
+#define XMK_STR(x) #x
+#define MK_STR(x) XMK_STR(x)
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "netdev=" MK_STR(CONFIG_NETDEV) "\0" \
+ "uboot=" MK_STR(CONFIG_UBOOTPATH) "\0" \
+ "tftpflash=tftp $loadaddr $uboot;" \
+ "protect off " MK_STR(TEXT_BASE) " +$filesize; " \
+ "erase " MK_STR(TEXT_BASE) " +$filesize; " \
+ "cp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize; " \
+ "protect on " MK_STR(TEXT_BASE) " +$filesize; " \
+ "cmp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize\0" \
+ "fdtaddr=400000\0" \
+ "fdtfile=" MK_STR(CONFIG_FDTFILE) "\0" \
+ "ramdiskaddr=1000000\0" \
+ "ramdiskfile=" MK_STR(CONFIG_RAMDISKFILE) "\0" \
+ "console=ttyS0\0" \
+ "setbootargs=setenv bootargs " \
+ "root=$rootdev rw console=$console,$baudrate $othbootargs\0" \
+ "setipargs=setenv bootargs nfsroot=$serverip:$rootpath " \
+ "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
+ "root=$rootdev rw console=$console,$baudrate $othbootargs\0"
+
+#define CONFIG_NFSBOOTCOMMAND \
+ "setenv rootdev /dev/nfs;" \
+ "run setbootargs;" \
+ "run setipargs;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr - $fdtaddr"
+
+#define CONFIG_RAMBOOTCOMMAND \
+ "setenv rootdev /dev/ram;" \
+ "run setbootargs;" \
+ "tftp $ramdiskaddr $ramdiskfile;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr $ramdiskaddr $fdtaddr"
+
+#undef MK_STR
+#undef XMK_STR
+
+#endif /* __CONFIG_H */
diff --git a/include/mpc83xx.h b/include/mpc83xx.h
index 7299ca0..39cecf2 100644
--- a/include/mpc83xx.h
+++ b/include/mpc83xx.h
@@ -725,13 +725,20 @@
#define SCCR_USBCM_3 0x00F00000
#elif defined(CONFIG_MPC8313)
-/* TSEC1 bits are for TSEC2 as well */
#define SCCR_TSEC1CM 0xc0000000
#define SCCR_TSEC1CM_SHIFT 30
+#define SCCR_TSEC1CM_0 0x00000000
#define SCCR_TSEC1CM_1 0x40000000
#define SCCR_TSEC1CM_2 0x80000000
#define SCCR_TSEC1CM_3 0xC0000000
+#define SCCR_TSEC2CM 0x30000000
+#define SCCR_TSEC2CM_SHIFT 28
+#define SCCR_TSEC2CM_0 0x00000000
+#define SCCR_TSEC2CM_1 0x10000000
+#define SCCR_TSEC2CM_2 0x20000000
+#define SCCR_TSEC2CM_3 0x30000000
+
#define SCCR_TSEC1ON 0x20000000
#define SCCR_TSEC1ON_SHIFT 29
#define SCCR_TSEC2ON 0x10000000
@@ -831,8 +838,6 @@
#define SCCR_PCIEXP2CM_3 0x000c0000
/* All of the four SATA controllers must have the same clock ratio */
-#define SCCR_SATA1CM 0x000000c0
-#define SCCR_SATA1CM_SHIFT 6
#define SCCR_SATACM 0x000000ff
#define SCCR_SATACM_SHIFT 0
#define SCCR_SATACM_0 0x00000000
@@ -852,6 +857,7 @@
*/
#define CSCONFIG_EN 0x80000000
#define CSCONFIG_AP 0x00800000
+#define CSCONFIG_ODT_WR_ACS 0x00010000
#define CSCONFIG_ROW_BIT 0x00000700
#define CSCONFIG_ROW_BIT_12 0x00000000
#define CSCONFIG_ROW_BIT_13 0x00000100
@@ -1480,6 +1486,7 @@
/* DDRCDR - DDR Control Driver Register
*/
+#define DDRCDR_DHC_EN 0x80000000
#define DDRCDR_EN 0x40000000
#define DDRCDR_PZ 0x3C000000
#define DDRCDR_PZ_MAXZ 0x00000000