diff options
-rw-r--r-- | arch/arm/mach-at91/include/mach/at91_pio.h | 6 | ||||
-rw-r--r-- | drivers/pinctrl/Kconfig | 14 | ||||
-rw-r--r-- | drivers/pinctrl/Makefile | 1 | ||||
-rw-r--r-- | drivers/pinctrl/pinctrl-at91.c | 453 | ||||
-rw-r--r-- | include/dt-bindings/pinctrl/at91.h | 2 |
5 files changed, 475 insertions, 1 deletions
diff --git a/arch/arm/mach-at91/include/mach/at91_pio.h b/arch/arm/mach-at91/include/mach/at91_pio.h index 946f076..4840a2b 100644 --- a/arch/arm/mach-at91/include/mach/at91_pio.h +++ b/arch/arm/mach-at91/include/mach/at91_pio.h @@ -109,7 +109,11 @@ typedef struct at91_port { u32 wpsr; /* 0xE8 Write Protect Status Register */ u32 reserved11[5]; /* */ u32 schmitt; /* 0x100 Schmitt Trigger Register */ - u32 reserved12[63]; + u32 reserved12[4]; /* 0x104 ~ 0x110 */ + u32 driver1; /* 0x114 I/O Driver Register1(AT91SAM9x5's driver1) */ + u32 driver12; /* 0x118 I/O Driver Register12(AT91SAM9x5's driver2 or SAMA5D3x's driver1 ) */ + u32 driver2; /* 0x11C I/O Driver Register2(SAMA5D3x's driver2) */ + u32 reserved13[12]; /* 0x120 ~ 0x14C */ } at91_port_t; typedef union at91_pio { diff --git a/drivers/pinctrl/Kconfig b/drivers/pinctrl/Kconfig index 9d0f501..355aeae 100644 --- a/drivers/pinctrl/Kconfig +++ b/drivers/pinctrl/Kconfig @@ -150,6 +150,20 @@ config ROCKCHIP_RK3288_PINCTRL definitions and pin control functions for each available multiplex function. +config PINCTRL_AT91 + bool "AT91 pinctrl driver" + depends on DM + help + This option is to enable the AT91 pinctrl driver for AT91 PIO + controller. AT91 PIO controller is a combined gpio-controller, + pin-mux and pin-config module. Each I/O pin may be dedicated as + a general-purpose I/O or be assigned to a function of an embedded + peripheral. Each I/O pin has a glitch filter providing rejection of + glitches lower than one-half of peripheral clock cycle and + a debouncing filter providing rejection of unwanted pulses from key + or push button operations. You can also control the multi-driver + capability, pull-up and pull-down feature on each I/O pin. + config PINCTRL_AT91PIO4 bool "AT91 PIO4 pinctrl driver" depends on DM diff --git a/drivers/pinctrl/Makefile b/drivers/pinctrl/Makefile index 2ac9c19..bbb2480 100644 --- a/drivers/pinctrl/Makefile +++ b/drivers/pinctrl/Makefile @@ -5,6 +5,7 @@ obj-y += pinctrl-uclass.o obj-$(CONFIG_$(SPL_)PINCTRL_GENERIC) += pinctrl-generic.o +obj-$(CONFIG_PINCTRL_AT91) += pinctrl-at91.o obj-$(CONFIG_PINCTRL_AT91PIO4) += pinctrl-at91-pio4.o obj-y += nxp/ obj-$(CONFIG_ARCH_ATH79) += ath79/ diff --git a/drivers/pinctrl/pinctrl-at91.c b/drivers/pinctrl/pinctrl-at91.c new file mode 100644 index 0000000..904e1bd --- /dev/null +++ b/drivers/pinctrl/pinctrl-at91.c @@ -0,0 +1,453 @@ +/* + * Atmel PIO pinctrl driver + * + * Copyright (C) 2016 Atmel Corporation + * Wenyou.Yang <wenyou.yang@atmel.com> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <dm/device.h> +#include <dm/pinctrl.h> +#include <linux/io.h> +#include <linux/err.h> +#include <mach/at91_pio.h> + +DECLARE_GLOBAL_DATA_PTR; + +#define MAX_GPIO_BANKS 5 +#define MAX_NB_GPIO_PER_BANK 32 + +#define MAX_PINMUX_ENTRIES 200 + +struct at91_pinctrl_priv { + struct at91_port *reg_base[MAX_GPIO_BANKS]; + u32 nbanks; +}; + +#define PULL_UP BIT(0) +#define MULTI_DRIVE BIT(1) +#define DEGLITCH BIT(2) +#define PULL_DOWN BIT(3) +#define DIS_SCHMIT BIT(4) +#define DRIVE_STRENGTH_SHIFT 5 +#define DRIVE_STRENGTH_MASK 0x3 +#define DRIVE_STRENGTH (DRIVE_STRENGTH_MASK << DRIVE_STRENGTH_SHIFT) +#define OUTPUT BIT(7) +#define OUTPUT_VAL_SHIFT 8 +#define OUTPUT_VAL (0x1 << OUTPUT_VAL_SHIFT) +#define DEBOUNCE BIT(16) +#define DEBOUNCE_VAL_SHIFT 17 +#define DEBOUNCE_VAL (0x3fff << DEBOUNCE_VAL_SHIFT) + +/** + * These defines will translated the dt binding settings to our internal + * settings. They are not necessarily the same value as the register setting. + * The actual drive strength current of low, medium and high must be looked up + * from the corresponding device datasheet. This value is different for pins + * that are even in the same banks. It is also dependent on VCC. + * DRIVE_STRENGTH_DEFAULT is just a placeholder to avoid changing the drive + * strength when there is no dt config for it. + */ +#define DRIVE_STRENGTH_DEFAULT (0 << DRIVE_STRENGTH_SHIFT) +#define DRIVE_STRENGTH_LOW (1 << DRIVE_STRENGTH_SHIFT) +#define DRIVE_STRENGTH_MED (2 << DRIVE_STRENGTH_SHIFT) +#define DRIVE_STRENGTH_HI (3 << DRIVE_STRENGTH_SHIFT) + +enum at91_mux { + AT91_MUX_GPIO = 0, + AT91_MUX_PERIPH_A = 1, + AT91_MUX_PERIPH_B = 2, + AT91_MUX_PERIPH_C = 3, + AT91_MUX_PERIPH_D = 4, +}; + +/** + * struct at91_pinctrl_mux_ops - describes an AT91 mux ops group + * on new IP with support for periph C and D the way to mux in + * periph A and B has changed + * So provide the right callbacks + * if not present means the IP does not support it + * @mux_A_periph: assign the corresponding pin to the peripheral A function. + * @mux_B_periph: assign the corresponding pin to the peripheral B function. + * @mux_C_periph: assign the corresponding pin to the peripheral C function. + * @mux_D_periph: assign the corresponding pin to the peripheral D function. + * @set_deglitch: enable/disable the deglitch feature. + * @set_debounce: enable/disable the debounce feature. + * @set_pulldown: enable/disable the pulldown feature. + * @disable_schmitt_trig: disable schmitt trigger + */ +struct at91_pinctrl_mux_ops { + void (*mux_A_periph)(struct at91_port *pio, u32 mask); + void (*mux_B_periph)(struct at91_port *pio, u32 mask); + void (*mux_C_periph)(struct at91_port *pio, u32 mask); + void (*mux_D_periph)(struct at91_port *pio, u32 mask); + void (*set_deglitch)(struct at91_port *pio, u32 mask, bool is_on); + void (*set_debounce)(struct at91_port *pio, u32 mask, bool is_on, + u32 div); + void (*set_pulldown)(struct at91_port *pio, u32 mask, bool is_on); + void (*disable_schmitt_trig)(struct at91_port *pio, u32 mask); + void (*set_drivestrength)(struct at91_port *pio, u32 pin, + u32 strength); +}; + +static u32 two_bit_pin_value_shift_amount(u32 pin) +{ + /* return the shift value for a pin for "two bit" per pin registers, + * i.e. drive strength */ + return 2 * ((pin >= MAX_NB_GPIO_PER_BANK/2) + ? pin - MAX_NB_GPIO_PER_BANK/2 : pin); +} + +static void at91_mux_disable_interrupt(struct at91_port *pio, u32 mask) +{ + writel(mask, &pio->idr); +} + +static void at91_mux_set_pullup(struct at91_port *pio, u32 mask, bool on) +{ + if (on) + writel(mask, &pio->mux.pio3.ppddr); + + writel(mask, (on ? &pio->puer : &pio->pudr)); +} + +static void at91_mux_set_output(struct at91_port *pio, unsigned mask, + bool is_on, bool val) +{ + writel(mask, (val ? &pio->sodr : &pio->codr)); + writel(mask, (is_on ? &pio->oer : &pio->odr)); +} + +static void at91_mux_set_multidrive(struct at91_port *pio, u32 mask, bool on) +{ + writel(mask, (on ? &pio->mder : &pio->mddr)); +} + +static void at91_mux_set_A_periph(struct at91_port *pio, u32 mask) +{ + writel(mask, &pio->mux.pio2.asr); +} + +static void at91_mux_set_B_periph(struct at91_port *pio, u32 mask) +{ + writel(mask, &pio->mux.pio2.bsr); +} + +static void at91_mux_pio3_set_A_periph(struct at91_port *pio, u32 mask) +{ + writel(readl(&pio->mux.pio3.abcdsr1) & ~mask, &pio->mux.pio3.abcdsr1); + writel(readl(&pio->mux.pio3.abcdsr2) & ~mask, &pio->mux.pio3.abcdsr2); +} + +static void at91_mux_pio3_set_B_periph(struct at91_port *pio, u32 mask) +{ + writel(readl(&pio->mux.pio3.abcdsr1) | mask, &pio->mux.pio3.abcdsr1); + writel(readl(&pio->mux.pio3.abcdsr2) & ~mask, &pio->mux.pio3.abcdsr2); +} + +static void at91_mux_pio3_set_C_periph(struct at91_port *pio, u32 mask) +{ + writel(readl(&pio->mux.pio3.abcdsr1) & ~mask, &pio->mux.pio3.abcdsr1); + writel(readl(&pio->mux.pio3.abcdsr2) | mask, &pio->mux.pio3.abcdsr2); +} + +static void at91_mux_pio3_set_D_periph(struct at91_port *pio, u32 mask) +{ + writel(readl(&pio->mux.pio3.abcdsr1) | mask, &pio->mux.pio3.abcdsr1); + writel(readl(&pio->mux.pio3.abcdsr2) | mask, &pio->mux.pio3.abcdsr2); +} + +static void at91_mux_set_deglitch(struct at91_port *pio, u32 mask, bool is_on) +{ + writel(mask, (is_on ? &pio->ifer : &pio->ifdr)); +} + +static void at91_mux_pio3_set_deglitch(struct at91_port *pio, + u32 mask, bool is_on) +{ + if (is_on) + writel(mask, &pio->mux.pio3.ifscdr); + at91_mux_set_deglitch(pio, mask, is_on); +} + +static void at91_mux_pio3_set_debounce(struct at91_port *pio, u32 mask, + bool is_on, u32 div) +{ + if (is_on) { + writel(mask, &pio->mux.pio3.ifscer); + writel(div & PIO_SCDR_DIV, &pio->mux.pio3.scdr); + writel(mask, &pio->ifer); + } else { + writel(mask, &pio->mux.pio3.ifscdr); + } +} + +static void at91_mux_pio3_set_pulldown(struct at91_port *pio, + u32 mask, bool is_on) +{ + if (is_on) + writel(mask, &pio->pudr); + + writel(mask, (is_on ? &pio->mux.pio3.ppder : &pio->mux.pio3.ppddr)); +} + +static void at91_mux_pio3_disable_schmitt_trig(struct at91_port *pio, + u32 mask) +{ + writel(readl(&pio->schmitt) | mask, &pio->schmitt); +} + +static void set_drive_strength(void *reg, u32 pin, u32 strength) +{ + u32 shift = two_bit_pin_value_shift_amount(pin); + + clrsetbits_le32(reg, DRIVE_STRENGTH_MASK << shift, strength << shift); +} + +static void at91_mux_sama5d3_set_drivestrength(struct at91_port *pio, + u32 pin, u32 setting) +{ + void *reg; + + reg = &pio->driver12; + if (pin >= MAX_NB_GPIO_PER_BANK / 2) + reg = &pio->driver2; + + /* do nothing if setting is zero */ + if (!setting) + return; + + /* strength is 1 to 1 with setting for SAMA5 */ + set_drive_strength(reg, pin, setting); +} + +static void at91_mux_sam9x5_set_drivestrength(struct at91_port *pio, + u32 pin, u32 setting) +{ + void *reg; + + reg = &pio->driver1; + if (pin >= MAX_NB_GPIO_PER_BANK / 2) + reg = &pio->driver12; + + /* do nothing if setting is zero */ + if (!setting) + return; + + /* strength is inverse on SAM9x5s with our defines + * 0 = hi, 1 = med, 2 = low, 3 = rsvd */ + setting = DRIVE_STRENGTH_HI - setting; + + set_drive_strength(reg, pin, setting); +} + +static struct at91_pinctrl_mux_ops at91rm9200_ops = { + .mux_A_periph = at91_mux_set_A_periph, + .mux_B_periph = at91_mux_set_B_periph, + .set_deglitch = at91_mux_set_deglitch, +}; + +static struct at91_pinctrl_mux_ops at91sam9x5_ops = { + .mux_A_periph = at91_mux_pio3_set_A_periph, + .mux_B_periph = at91_mux_pio3_set_B_periph, + .mux_C_periph = at91_mux_pio3_set_C_periph, + .mux_D_periph = at91_mux_pio3_set_D_periph, + .set_deglitch = at91_mux_pio3_set_deglitch, + .set_debounce = at91_mux_pio3_set_debounce, + .set_pulldown = at91_mux_pio3_set_pulldown, + .disable_schmitt_trig = at91_mux_pio3_disable_schmitt_trig, + .set_drivestrength = at91_mux_sam9x5_set_drivestrength, +}; + +static struct at91_pinctrl_mux_ops sama5d3_ops = { + .mux_A_periph = at91_mux_pio3_set_A_periph, + .mux_B_periph = at91_mux_pio3_set_B_periph, + .mux_C_periph = at91_mux_pio3_set_C_periph, + .mux_D_periph = at91_mux_pio3_set_D_periph, + .set_deglitch = at91_mux_pio3_set_deglitch, + .set_debounce = at91_mux_pio3_set_debounce, + .set_pulldown = at91_mux_pio3_set_pulldown, + .disable_schmitt_trig = at91_mux_pio3_disable_schmitt_trig, + .set_drivestrength = at91_mux_sama5d3_set_drivestrength, +}; + +static void at91_mux_gpio_disable(struct at91_port *pio, u32 mask) +{ + writel(mask, &pio->pdr); +} + +static void at91_mux_gpio_enable(struct at91_port *pio, u32 mask, bool input) +{ + writel(mask, &pio->per); + writel(mask, (input ? &pio->odr : &pio->oer)); +} + +static int at91_pmx_set(struct at91_pinctrl_mux_ops *ops, + struct at91_port *pio, u32 mask, enum at91_mux mux) +{ + at91_mux_disable_interrupt(pio, mask); + switch (mux) { + case AT91_MUX_GPIO: + at91_mux_gpio_enable(pio, mask, 1); + break; + case AT91_MUX_PERIPH_A: + ops->mux_A_periph(pio, mask); + break; + case AT91_MUX_PERIPH_B: + ops->mux_B_periph(pio, mask); + break; + case AT91_MUX_PERIPH_C: + if (!ops->mux_C_periph) + return -EINVAL; + ops->mux_C_periph(pio, mask); + break; + case AT91_MUX_PERIPH_D: + if (!ops->mux_D_periph) + return -EINVAL; + ops->mux_D_periph(pio, mask); + break; + } + if (mux) + at91_mux_gpio_disable(pio, mask); + + return 0; +} + +static int at91_pinconf_set(struct at91_pinctrl_mux_ops *ops, + struct at91_port *pio, u32 pin, u32 config) +{ + u32 mask = BIT(pin); + + if ((config & PULL_UP) && (config & PULL_DOWN)) + return -EINVAL; + + at91_mux_set_output(pio, mask, config & OUTPUT, + (config & OUTPUT_VAL) >> OUTPUT_VAL_SHIFT); + at91_mux_set_pullup(pio, mask, config & PULL_UP); + at91_mux_set_multidrive(pio, mask, config & MULTI_DRIVE); + if (ops->set_deglitch) + ops->set_deglitch(pio, mask, config & DEGLITCH); + if (ops->set_debounce) + ops->set_debounce(pio, mask, config & DEBOUNCE, + (config & DEBOUNCE_VAL) >> DEBOUNCE_VAL_SHIFT); + if (ops->set_pulldown) + ops->set_pulldown(pio, mask, config & PULL_DOWN); + if (ops->disable_schmitt_trig && config & DIS_SCHMIT) + ops->disable_schmitt_trig(pio, mask); + if (ops->set_drivestrength) + ops->set_drivestrength(pio, pin, + (config & DRIVE_STRENGTH) >> DRIVE_STRENGTH_SHIFT); + + return 0; +} + +static int at91_pin_check_config(struct udevice *dev, u32 bank, u32 pin) +{ + struct at91_pinctrl_priv *priv = dev_get_priv(dev); + + if (bank >= priv->nbanks) { + debug("pin conf bank %d >= nbanks %d\n", bank, priv->nbanks); + return -EINVAL; + } + + if (pin >= MAX_NB_GPIO_PER_BANK) { + debug("pin conf pin %d >= %d\n", pin, MAX_NB_GPIO_PER_BANK); + return -EINVAL; + } + + return 0; +} + +static int at91_pinctrl_set_state(struct udevice *dev, struct udevice *config) +{ + struct at91_pinctrl_priv *priv = dev_get_priv(dev); + const void *blob = gd->fdt_blob; + int node = config->of_offset; + u32 cells[MAX_PINMUX_ENTRIES]; + const u32 *list = cells; + u32 bank, pin; + u32 conf, mask, count, i; + int size; + int ret; + enum at91_mux mux; + struct at91_port *pio; + struct at91_pinctrl_mux_ops *ops = + (struct at91_pinctrl_mux_ops *)dev_get_driver_data(dev); + + /* + * the binding format is atmel,pins = <bank pin mux CONFIG ...>, + * do sanity check and calculate pins number + */ + size = fdtdec_get_int_array_count(blob, node, "atmel,pins", + cells, ARRAY_SIZE(cells)); + + /* we do not check return since it's safe node passed down */ + count = size >> 2; + if (!count) + return -EINVAL; + + for (i = 0; i < count; i++) { + bank = *list++; + pin = *list++; + mux = *list++; + conf = *list++; + + ret = at91_pin_check_config(dev, bank, pin); + if (ret) + return ret; + + pio = priv->reg_base[bank]; + mask = BIT(pin); + + ret = at91_pmx_set(ops, pio, mask, mux); + if (ret) + return ret; + + ret = at91_pinconf_set(ops, pio, pin, conf); + if (ret) + return ret; + } + + return 0; +} + +const struct pinctrl_ops at91_pinctrl_ops = { + .set_state = at91_pinctrl_set_state, +}; + +static int at91_pinctrl_probe(struct udevice *dev) +{ + struct at91_pinctrl_priv *priv = dev_get_priv(dev); + fdt_addr_t addr_base; + int index; + + for (index = 0; index < MAX_GPIO_BANKS; index++) { + addr_base = dev_get_addr_index(dev, index); + if (addr_base == FDT_ADDR_T_NONE) + break; + + priv->reg_base[index] = (struct at91_port *)addr_base; + } + + priv->nbanks = index; + + return 0; +} + +static const struct udevice_id at91_pinctrl_match[] = { + { .compatible = "atmel,sama5d3-pinctrl", .data = (ulong)&sama5d3_ops }, + { .compatible = "atmel,at91sam9x5-pinctrl", .data = (ulong)&at91sam9x5_ops }, + { .compatible = "atmel,at91rm9200-pinctrl", .data = (ulong)&at91rm9200_ops }, + {} +}; + +U_BOOT_DRIVER(at91_pinctrl) = { + .name = "pinctrl_at91", + .id = UCLASS_PINCTRL, + .of_match = at91_pinctrl_match, + .probe = at91_pinctrl_probe, + .priv_auto_alloc_size = sizeof(struct at91_pinctrl_priv), + .ops = &at91_pinctrl_ops, +}; diff --git a/include/dt-bindings/pinctrl/at91.h b/include/dt-bindings/pinctrl/at91.h index bbca3d0..2732d6c 100644 --- a/include/dt-bindings/pinctrl/at91.h +++ b/include/dt-bindings/pinctrl/at91.h @@ -15,6 +15,8 @@ #define AT91_PINCTRL_DEGLITCH (1 << 2) #define AT91_PINCTRL_PULL_DOWN (1 << 3) #define AT91_PINCTRL_DIS_SCHMIT (1 << 4) +#define AT91_PINCTRL_OUTPUT (1 << 7) +#define AT91_PINCTRL_OUTPUT_VAL(x) ((x & 0x1) << 8) #define AT91_PINCTRL_DEBOUNCE (1 << 16) #define AT91_PINCTRL_DEBOUNCE_VAL(x) (x << 17) |