diff options
| -rw-r--r-- | arch/arm/dts/Makefile | 3 | ||||
| -rw-r--r-- | arch/arm/dts/armada-xp-synology-ds414.dts | 337 | ||||
| -rw-r--r-- | arch/arm/mach-mvebu/Kconfig | 7 | ||||
| -rw-r--r-- | arch/arm/mach-mvebu/serdes/axp/board_env_spec.h | 2 | ||||
| -rw-r--r-- | board/Synology/ds414/Makefile | 7 | ||||
| -rw-r--r-- | board/Synology/ds414/ds414.c | 185 | ||||
| -rw-r--r-- | board/Synology/ds414/kwbimage.cfg | 12 | ||||
| -rw-r--r-- | configs/ds414_defconfig | 18 | ||||
| -rw-r--r-- | include/configs/ds414.h | 162 |
9 files changed, 731 insertions, 2 deletions
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index 084f113..64b8371 100644 --- a/arch/arm/dts/Makefile +++ b/arch/arm/dts/Makefile @@ -51,7 +51,8 @@ dtb-$(CONFIG_ARCH_MVEBU) += \ armada-388-clearfog.dtb \ armada-388-gp.dtb \ armada-xp-gp.dtb \ - armada-xp-maxbcm.dtb + armada-xp-maxbcm.dtb \ + armada-xp-synology-ds414.dtb dtb-$(CONFIG_ARCH_UNIPHIER) += \ uniphier-ph1-ld4-ref.dtb \ diff --git a/arch/arm/dts/armada-xp-synology-ds414.dts b/arch/arm/dts/armada-xp-synology-ds414.dts new file mode 100644 index 0000000..0a60ddf --- /dev/null +++ b/arch/arm/dts/armada-xp-synology-ds414.dts @@ -0,0 +1,337 @@ +/* + * Device Tree file for Synology DS414 + * + * Copyright (C) 2014, Arnaud EBALARD <arno@natisbad.org> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; either version + * 2 of the License, or (at your option) any later version. + * + * Note: this Device Tree assumes that the bootloader has remapped the + * internal registers to 0xf1000000 (instead of the old 0xd0000000). + * The 0xf1000000 is the default used by the recent, DT-capable, U-Boot + * bootloaders provided by Marvell. It is used in recent versions of + * DSM software provided by Synology. Nonetheless, some earlier boards + * were delivered with an older version of u-boot that left internal + * registers mapped at 0xd0000000. If you have such a device you will + * not be able to directly boot a kernel based on this Device Tree. In + * that case, the preferred solution is to update your bootloader (e.g. + * by upgrading to latest version of DSM, or building a new one and + * installing it from u-boot prompt) or adjust the Devive Tree + * (s/0xf1000000/0xd0000000/ in 'ranges' below). + */ + +/dts-v1/; + +#include <dt-bindings/input/input.h> +#include <dt-bindings/gpio/gpio.h> +#include "armada-xp-mv78230.dtsi" + +/ { + model = "Synology DS414"; + compatible = "synology,ds414", "marvell,armadaxp-mv78230", + "marvell,armadaxp", "marvell,armada-370-xp"; + + chosen { + bootargs = "console=ttyS0,115200 earlyprintk"; + stdout-path = &uart0; + }; + + aliases { + spi0 = &spi0; + }; + + memory { + device_type = "memory"; + reg = <0 0x00000000 0 0x40000000>; /* 1GB */ + }; + + soc { + ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xf1000000 0x100000 + MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000>; + + pcie-controller { + status = "okay"; + + /* + * Connected to Marvell 88SX7042 SATA-II controller + * handling the four disks. + */ + pcie@1,0 { + /* Port 0, Lane 0 */ + status = "okay"; + }; + + /* + * Connected to EtronTech EJ168A XHCI controller + * providing the two rear USB 3.0 ports. + */ + pcie@5,0 { + /* Port 1, Lane 0 */ + status = "okay"; + }; + }; + + internal-regs { + + /* RTC is provided by Seiko S-35390A below */ + rtc@10300 { + status = "disabled"; + }; + + spi0: spi@10600 { + status = "okay"; + u-boot,dm-pre-reloc; + + spi-flash@0 { + u-boot,dm-pre-reloc; + #address-cells = <1>; + #size-cells = <1>; + compatible = "micron,n25q064"; + reg = <0>; /* Chip select 0 */ + spi-max-frequency = <20000000>; + + /* + * Warning! + * + * Synology u-boot uses its compiled-in environment + * and it seems Synology did not care to change u-boot + * default configuration in order to allow saving a + * modified environment at a sensible location. So, + * if you do a 'saveenv' under u-boot, your modified + * environment will be saved at 1MB after the start + * of the flash, i.e. in the middle of the uImage. + * For that reason, it is strongly advised not to + * change the default environment, unless you know + * what you are doing. + */ + partition@00000000 { /* u-boot */ + label = "RedBoot"; + reg = <0x00000000 0x000d0000>; /* 832KB */ + }; + + partition@000c0000 { /* uImage */ + label = "zImage"; + reg = <0x000d0000 0x002d0000>; /* 2880KB */ + }; + + partition@003a0000 { /* uInitramfs */ + label = "rd.gz"; + reg = <0x003a0000 0x00430000>; /* 4250KB */ + }; + + partition@007d0000 { /* MAC address and serial number */ + label = "vendor"; + reg = <0x007d0000 0x00010000>; /* 64KB */ + }; + + partition@007e0000 { + label = "RedBoot config"; + reg = <0x007e0000 0x00010000>; /* 64KB */ + }; + + partition@007f0000 { + label = "FIS directory"; + reg = <0x007f0000 0x00010000>; /* 64KB */ + }; + }; + }; + + i2c@11000 { + clock-frequency = <400000>; + status = "okay"; + + s35390a: s35390a@30 { + compatible = "sii,s35390a"; + reg = <0x30>; + }; + }; + + /* Connected to a header on device's PCB. This + * provides the main console for the device. + * + * Warning: the device may not boot with a 3.3V + * USB-serial converter connected when the power + * button is pressed. The converter needs to be + * connected a few seconds after pressing the + * power button. This is possibly due to UART0_TXD + * pin being sampled at reset (bit 0 of SAR). + */ + serial@12000 { + status = "okay"; + u-boot,dm-pre-reloc; + }; + + /* Connected to a Microchip PIC16F883 for power control */ + serial@12100 { + status = "okay"; + }; + + poweroff@12100 { + compatible = "synology,power-off"; + reg = <0x12100 0x100>; + clocks = <&coreclk 0>; + }; + + /* Front USB 2.0 port */ + usb@50000 { + status = "okay"; + }; + + mdio { + phy0: ethernet-phy@0 { /* Marvell 88E1512 */ + reg = <0>; + }; + + phy1: ethernet-phy@1 { /* Marvell 88E1512 */ + reg = <1>; + }; + }; + + ethernet@70000 { + status = "okay"; + pinctrl-0 = <&ge0_rgmii_pins>; + pinctrl-names = "default"; + phy = <&phy1>; + phy-mode = "rgmii-id"; + }; + + ethernet@74000 { + pinctrl-0 = <&ge1_rgmii_pins>; + pinctrl-names = "default"; + status = "okay"; + phy = <&phy0>; + phy-mode = "rgmii-id"; + }; + }; + }; + + regulators { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + pinctrl-0 = <&sata1_pwr_pin &sata2_pwr_pin + &sata3_pwr_pin &sata4_pwr_pin>; + pinctrl-names = "default"; + + sata1_regulator: sata1-regulator { + compatible = "regulator-fixed"; + reg = <1>; + regulator-name = "SATA1 Power"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + startup-delay-us = <2000000>; + enable-active-high; + regulator-always-on; + regulator-boot-on; + gpio = <&gpio1 10 GPIO_ACTIVE_HIGH>; + }; + + sata2_regulator: sata2-regulator { + compatible = "regulator-fixed"; + reg = <2>; + regulator-name = "SATA2 Power"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + startup-delay-us = <4000000>; + enable-active-high; + regulator-always-on; + regulator-boot-on; + gpio = <&gpio1 12 GPIO_ACTIVE_HIGH>; + }; + + sata3_regulator: sata3-regulator { + compatible = "regulator-fixed"; + reg = <3>; + regulator-name = "SATA3 Power"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + startup-delay-us = <6000000>; + enable-active-high; + regulator-always-on; + regulator-boot-on; + gpio = <&gpio1 13 GPIO_ACTIVE_HIGH>; + }; + + sata4_regulator: sata4-regulator { + compatible = "regulator-fixed"; + reg = <4>; + regulator-name = "SATA4 Power"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + startup-delay-us = <8000000>; + enable-active-high; + regulator-always-on; + regulator-boot-on; + gpio = <&gpio1 14 GPIO_ACTIVE_HIGH>; + }; + }; +}; + +&pinctrl { + sata1_pwr_pin: sata1-pwr-pin { + marvell,pins = "mpp42"; + marvell,function = "gpio"; + }; + + sata2_pwr_pin: sata2-pwr-pin { + marvell,pins = "mpp44"; + marvell,function = "gpio"; + }; + + sata3_pwr_pin: sata3-pwr-pin { + marvell,pins = "mpp45"; + marvell,function = "gpio"; + }; + + sata4_pwr_pin: sata4-pwr-pin { + marvell,pins = "mpp46"; + marvell,function = "gpio"; + }; + + sata1_pres_pin: sata1-pres-pin { + marvell,pins = "mpp34"; + marvell,function = "gpio"; + }; + + sata2_pres_pin: sata2-pres-pin { + marvell,pins = "mpp35"; + marvell,function = "gpio"; + }; + + sata3_pres_pin: sata3-pres-pin { + marvell,pins = "mpp40"; + marvell,function = "gpio"; + }; + + sata4_pres_pin: sata4-pres-pin { + marvell,pins = "mpp41"; + marvell,function = "gpio"; + }; + + syno_id_bit0_pin: syno-id-bit0-pin { + marvell,pins = "mpp26"; + marvell,function = "gpio"; + }; + + syno_id_bit1_pin: syno-id-bit1-pin { + marvell,pins = "mpp28"; + marvell,function = "gpio"; + }; + + syno_id_bit2_pin: syno-id-bit2-pin { + marvell,pins = "mpp29"; + marvell,function = "gpio"; + }; + + fan1_alarm_pin: fan1-alarm-pin { + marvell,pins = "mpp33"; + marvell,function = "gpio"; + }; + + fan2_alarm_pin: fan2-alarm-pin { + marvell,pins = "mpp32"; + marvell,function = "gpio"; + }; +}; diff --git a/arch/arm/mach-mvebu/Kconfig b/arch/arm/mach-mvebu/Kconfig index 35d44f6..b962846 100644 --- a/arch/arm/mach-mvebu/Kconfig +++ b/arch/arm/mach-mvebu/Kconfig @@ -38,6 +38,10 @@ config TARGET_DB_MV784MP_GP bool "Support db-mv784mp-gp" select MV78460 +config TARGET_DS414 + bool "Support Synology DS414" + select MV78230 + config TARGET_MAXBCM bool "Support maxbcm" select MV78460 @@ -48,18 +52,21 @@ config SYS_BOARD default "clearfog" if TARGET_CLEARFOG default "db-88f6820-gp" if TARGET_DB_88F6820_GP default "db-mv784mp-gp" if TARGET_DB_MV784MP_GP + default "ds414" if TARGET_DS414 default "maxbcm" if TARGET_MAXBCM config SYS_CONFIG_NAME default "clearfog" if TARGET_CLEARFOG default "db-88f6820-gp" if TARGET_DB_88F6820_GP default "db-mv784mp-gp" if TARGET_DB_MV784MP_GP + default "ds414" if TARGET_DS414 default "maxbcm" if TARGET_MAXBCM config SYS_VENDOR default "Marvell" if TARGET_DB_MV784MP_GP default "Marvell" if TARGET_DB_88F6820_GP default "solidrun" if TARGET_CLEARFOG + default "Synology" if TARGET_DS414 config SYS_SOC default "mvebu" diff --git a/arch/arm/mach-mvebu/serdes/axp/board_env_spec.h b/arch/arm/mach-mvebu/serdes/axp/board_env_spec.h index f00f327..c8d9485 100644 --- a/arch/arm/mach-mvebu/serdes/axp/board_env_spec.h +++ b/arch/arm/mach-mvebu/serdes/axp/board_env_spec.h @@ -44,7 +44,7 @@ #define DB_784MP_GP_ID (RD_78460_SERVER_REV2_ID + 1) #define RD_78460_CUSTOMER_ID (DB_784MP_GP_ID + 1) #define MV_MAX_BOARD_ID (RD_78460_CUSTOMER_ID + 1) -#define INVALID_BAORD_ID 0xFFFFFFFF +#define INVALID_BOARD_ID 0xFFFFFFFF /* Sample at Reset */ #define MPP_SAMPLE_AT_RESET(id) (0x18230 + (id * 4)) diff --git a/board/Synology/ds414/Makefile b/board/Synology/ds414/Makefile new file mode 100644 index 0000000..0f4c32d --- /dev/null +++ b/board/Synology/ds414/Makefile @@ -0,0 +1,7 @@ +# +# Copyright (C) 2015 Phil Sutter <phil@nwl.cc> +# +# SPDX-License-Identifier: GPL-2.0+ +# + +obj-y := ds414.o diff --git a/board/Synology/ds414/ds414.c b/board/Synology/ds414/ds414.c new file mode 100644 index 0000000..d563e89 --- /dev/null +++ b/board/Synology/ds414/ds414.c @@ -0,0 +1,185 @@ +/* + * + * Copyright (C) 2015 Phil Sutter <phil@nwl.cc> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <miiphy.h> +#include <asm/io.h> +#include <asm/arch/cpu.h> +#include <asm/arch/soc.h> +#include <linux/mbus.h> + +#include "../drivers/ddr/marvell/axp/ddr3_hw_training.h" +#include "../arch/arm/mach-mvebu/serdes/axp/high_speed_env_spec.h" +#include "../arch/arm/mach-mvebu/serdes/axp/board_env_spec.h" + +DECLARE_GLOBAL_DATA_PTR; + +/* GPP and MPP settings as found in mvBoardEnvSpec.c of Synology's U-Boot */ + +#define DS414_GPP_OUT_VAL_LOW (BIT(25) | BIT(30)) +#define DS414_GPP_OUT_VAL_MID (BIT(10) | BIT(15)) +#define DS414_GPP_OUT_VAL_HIGH (0) + +#define DS414_GPP_OUT_POL_LOW (0) +#define DS414_GPP_OUT_POL_MID (0) +#define DS414_GPP_OUT_POL_HIGH (0) + +#define DS414_GPP_OUT_ENA_LOW (~(BIT(25) | BIT(30))) +#define DS414_GPP_OUT_ENA_MID (~(BIT(10) | BIT(12) | \ + BIT(13) | BIT(14) | BIT(15))) +#define DS414_GPP_OUT_ENA_HIGH (~0) + +static const u32 ds414_mpp_control[] = { + 0x11111111, + 0x22221111, + 0x22222222, + 0x00000000, + 0x11110000, + 0x00004000, + 0x00000000, + 0x00000000, + 0x00000000 +}; + +/* DDR3 static MC configuration */ + +/* 1G_v1 (4x2Gbits) adapted by DS414 */ +MV_DRAM_MC_INIT syno_ddr3_b0_667_1g_v1[MV_MAX_DDR3_STATIC_SIZE] = { + {0x00001400, 0x73014A28}, /*DDR SDRAM Configuration Register */ + {0x00001404, 0x30000800}, /*Dunit Control Low Register */ + {0x00001408, 0x44148887}, /*DDR SDRAM Timing (Low) Register */ + {0x0000140C, 0x3AD83FEA}, /*DDR SDRAM Timing (High) Register */ + + {0x00001410, 0x14000000}, /*DDR SDRAM Address Control Register */ + + {0x00001414, 0x00000000}, /*DDR SDRAM Open Pages Control Register */ + {0x00001418, 0x00000e00}, /*DDR SDRAM Operation Register */ + {0x00001420, 0x00000004}, /*DDR SDRAM Extended Mode Register */ + {0x00001424, 0x0000F3FF}, /*Dunit Control High Register */ + {0x00001428, 0x000F8830}, /*Dunit Control High Register */ + {0x0000142C, 0x054C36F4}, /*Dunit Control High Register */ + {0x0000147C, 0x0000C671}, + + {0x000014a0, 0x00000001}, + {0x000014a8, 0x00000100}, /*2:1 */ + {0x00020220, 0x00000006}, + + {0x00001494, 0x00010000}, /*DDR SDRAM ODT Control (Low) Register */ + {0x00001498, 0x00000000}, /*DDR SDRAM ODT Control (High) Register */ + {0x0000149C, 0x00000001}, /*DDR Dunit ODT Control Register */ + + {0x000014C0, 0x192424C9}, /* DRAM address and Control Driving Strenght */ + {0x000014C4, 0x0AAA24C9}, /* DRAM Data and DQS Driving Strenght */ + + {0x000200e8, 0x3FFF0E01}, /* DO NOT Modify - Open Mbus Window - 2G - Mbus is required for the training sequence*/ + {0x00020184, 0x3FFFFFE0}, /* DO NOT Modify - Close fast path Window to - 2G */ + + {0x0001504, 0x3FFFFFE1}, /* CS0 Size */ + {0x000150C, 0x00000000}, /* CS1 Size */ + {0x0001514, 0x00000000}, /* CS2 Size */ + {0x000151C, 0x00000000}, /* CS3 Size */ + + {0x00001538, 0x00000009}, /*Read Data Sample Delays Register */ + {0x0000153C, 0x00000009}, /*Read Data Ready Delay Register */ + + {0x000015D0, 0x00000650}, /*MR0 */ + {0x000015D4, 0x00000044}, /*MR1 */ + {0x000015D8, 0x00000010}, /*MR2 */ + {0x000015DC, 0x00000000}, /*MR3 */ + + {0x000015E4, 0x00203c18}, /*ZQC Configuration Register */ + {0x000015EC, 0xF800A225}, /*DDR PHY */ + + {0x0, 0x0} +}; + +MV_DRAM_MODES ds414_ddr_modes[MV_DDR3_MODES_NUMBER] = { + {"ds414_1333-667", 0x3, 0x5, 0x0, A0, syno_ddr3_b0_667_1g_v1, NULL}, +}; + +extern MV_SERDES_CHANGE_M_PHY serdes_change_m_phy[]; + +MV_BIN_SERDES_CFG ds414_serdes_cfg[] = { + { MV_PEX_ROOT_COMPLEX, 0x02011111, 0x00000000, + { PEX_BUS_MODE_X4, PEX_BUS_MODE_X1, PEX_BUS_DISABLED, + PEX_BUS_DISABLED }, + 0x0040, serdes_change_m_phy + } +}; + +MV_DRAM_MODES *ddr3_get_static_ddr_mode(void) +{ + return &ds414_ddr_modes[0]; +} + +MV_BIN_SERDES_CFG *board_serdes_cfg_get(u8 pex_mode) +{ + return &ds414_serdes_cfg[0]; +} + +u8 board_sat_r_get(u8 dev_num, u8 reg) +{ + return (0x1 << 1 | 1); +} + +int board_early_init_f(void) +{ + int i; + + /* Set GPP Out value */ + reg_write(GPP_DATA_OUT_REG(0), DS414_GPP_OUT_VAL_LOW); + reg_write(GPP_DATA_OUT_REG(1), DS414_GPP_OUT_VAL_MID); + reg_write(GPP_DATA_OUT_REG(2), DS414_GPP_OUT_VAL_HIGH); + + /* set GPP polarity */ + reg_write(GPP_DATA_IN_POL_REG(0), DS414_GPP_OUT_POL_LOW); + reg_write(GPP_DATA_IN_POL_REG(1), DS414_GPP_OUT_POL_MID); + reg_write(GPP_DATA_IN_POL_REG(2), DS414_GPP_OUT_POL_HIGH); + + /* Set GPP Out Enable */ + reg_write(GPP_DATA_OUT_EN_REG(0), DS414_GPP_OUT_ENA_LOW); + reg_write(GPP_DATA_OUT_EN_REG(1), DS414_GPP_OUT_ENA_MID); + reg_write(GPP_DATA_OUT_EN_REG(2), DS414_GPP_OUT_ENA_HIGH); + + for (i = 0; i < ARRAY_SIZE(ds414_mpp_control); i++) + reg_write(MPP_CONTROL_REG(i), ds414_mpp_control[i]); + + return 0; +} + +int board_init(void) +{ + u32 pwr_mng_ctrl_reg; + + /* Adress of boot parameters */ + gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100; + + /* Gate unused clocks + * + * Note: Disabling unused PCIe lanes will hang PCI bus scan. + * Once this is resolved, bits 10-12, 26 and 27 can be + * unset here as well. + */ + pwr_mng_ctrl_reg = reg_read(POWER_MNG_CTRL_REG); + pwr_mng_ctrl_reg &= ~(BIT(0)); /* Audio */ + pwr_mng_ctrl_reg &= ~(BIT(1) | BIT(2)); /* GE3, GE2 */ + pwr_mng_ctrl_reg &= ~(BIT(14) | BIT(15)); /* SATA0 link and core */ + pwr_mng_ctrl_reg &= ~(BIT(16)); /* LCD */ + pwr_mng_ctrl_reg &= ~(BIT(17)); /* SDIO */ + pwr_mng_ctrl_reg &= ~(BIT(19) | BIT(20)); /* USB1 and USB2 */ + pwr_mng_ctrl_reg &= ~(BIT(29) | BIT(30)); /* SATA1 link and core */ + reg_write(POWER_MNG_CTRL_REG, pwr_mng_ctrl_reg); + + return 0; +} + +int checkboard(void) +{ + puts("Board: DS414\n"); + + return 0; +} diff --git a/board/Synology/ds414/kwbimage.cfg b/board/Synology/ds414/kwbimage.cfg new file mode 100644 index 0000000..1f748db --- /dev/null +++ b/board/Synology/ds414/kwbimage.cfg @@ -0,0 +1,12 @@ +# +# Copyright (C) 2014 Stefan Roese <sr@denx.de> +# + +# Armada XP uses version 1 image format +VERSION 1 + +# Boot Media configurations +BOOT_FROM spi + +# Binary Header (bin_hdr) with DDR3 training code +BINARY spl/u-boot-spl-dtb.bin 0000005b 00000068 diff --git a/configs/ds414_defconfig b/configs/ds414_defconfig new file mode 100644 index 0000000..4c3c1df --- /dev/null +++ b/configs/ds414_defconfig @@ -0,0 +1,18 @@ +CONFIG_ARM=y +CONFIG_ARCH_MVEBU=y +CONFIG_SYS_MALLOC_F_LEN=0x2000 +CONFIG_TARGET_DS414=y +CONFIG_DEFAULT_DEVICE_TREE="armada-xp-synology-ds414" +CONFIG_SPL=y +# CONFIG_CMD_IMLS is not set +# CONFIG_CMD_FLASH is not set +# CONFIG_CMD_SETEXPR is not set +CONFIG_SPL_OF_TRANSLATE=y +CONFIG_SPI_FLASH=y +CONFIG_SPI_FLASH_BAR=y +CONFIG_SPI_FLASH_STMICRO=y +CONFIG_DEBUG_UART=y +CONFIG_DEBUG_UART_BASE=0xd0012000 +CONFIG_DEBUG_UART_CLOCK=250000000 +CONFIG_DEBUG_UART_SHIFT=2 +CONFIG_SYS_NS16550=y diff --git a/include/configs/ds414.h b/include/configs/ds414.h new file mode 100644 index 0000000..e3c7087 --- /dev/null +++ b/include/configs/ds414.h @@ -0,0 +1,162 @@ +/* + * Copyright (C) 2014 Stefan Roese <sr@denx.de> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef _CONFIG_SYNOLOGY_DS414_H +#define _CONFIG_SYNOLOGY_DS414_H + +/* + * High Level Configuration Options (easy to change) + */ +#define CONFIG_DISPLAY_BOARDINFO_LATE + +/* + * TEXT_BASE needs to be below 16MiB, since this area is scrubbed + * for DDR ECC byte filling in the SPL before loading the main + * U-Boot into it. + */ +#define CONFIG_SYS_TEXT_BASE 0x00800000 +#define CONFIG_SYS_TCLK 250000000 /* 250MHz */ + +/* + * Commands configuration + */ +#define CONFIG_SYS_NO_FLASH /* Declare no flash (NOR/SPI) */ +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_ENV +#define CONFIG_CMD_I2C +#define CONFIG_CMD_PING +#define CONFIG_CMD_SF +#define CONFIG_CMD_SPI +#define CONFIG_CMD_TFTPPUT +#define CONFIG_CMD_TIME +#define CONFIG_CMD_USB + +/* I2C */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_MVTWSI +#define CONFIG_I2C_MVTWSI_BASE0 MVEBU_TWSI_BASE +#define CONFIG_SYS_I2C_SLAVE 0x0 +#define CONFIG_SYS_I2C_SPEED 100000 + +/* SPI NOR flash default params, used by sf commands */ +#define CONFIG_SF_DEFAULT_SPEED 1000000 +#define CONFIG_SF_DEFAULT_MODE SPI_MODE_3 + +/* Environment in SPI NOR flash */ +#define CONFIG_ENV_IS_IN_SPI_FLASH +#define CONFIG_ENV_OFFSET 0x7E0000 /* RedBoot config partition in DTS */ +#define CONFIG_ENV_SIZE (64 << 10) /* 64KiB */ +#define CONFIG_ENV_SECT_SIZE (64 << 10) /* 64KiB sectors */ + +#define CONFIG_PHY_MARVELL /* there is a marvell phy */ +#define CONFIG_PHY_ADDR { 0x1, 0x0 } +#define CONFIG_SYS_NETA_INTERFACE_TYPE PHY_INTERFACE_MODE_RGMII + +#define CONFIG_SYS_ALT_MEMTEST + +/* PCIe support */ +#ifndef CONFIG_SPL_BUILD +#define CONFIG_PCI +#define CONFIG_CMD_PCI +#define CONFIG_CMD_PCI_ENUM +#define CONFIG_PCI_MVEBU +#define CONFIG_PCI_SCAN_SHOW +#endif + +/* USB/EHCI/XHCI configuration */ + +#define CONFIG_DM_USB +#define CONFIG_USB_MAX_CONTROLLER_COUNT 2 + +/* FIXME: broken XHCI support + * Below defines should enable support for the two rear USB3 ports. Sadly, this + * does not work because: + * - xhci-pci seems to not support DM_USB, so with that enabled it is not + * found. + * - USB init fails, controller does not respond in time */ +#if 0 +#undef CONFIG_DM_USB +#define CONFIG_USB_XHCI +#define CONFIG_USB_XHCI_PCI +#define CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS 2 +#endif + +#if !defined(CONFIG_USB_XHCI) +#define CONFIG_USB_EHCI +#define CONFIG_USB_EHCI_MARVELL +#define CONFIG_EHCI_IS_TDI +#endif + +/* why is this only defined in mv-common.h if CONFIG_DM is undefined? */ +#define CONFIG_USB_STORAGE +#define CONFIG_DOS_PARTITION +#define CONFIG_ISO_PARTITION +#define CONFIG_SUPPORT_VFAT +#define CONFIG_SYS_MVFS + +/* + * mv-common.h should be defined after CMD configs since it used them + * to enable certain macros + */ +#include "mv-common.h" + +/* + * Memory layout while starting into the bin_hdr via the + * BootROM: + * + * 0x4000.4000 - 0x4003.4000 headers space (192KiB) + * 0x4000.4030 bin_hdr start address + * 0x4003.4000 - 0x4004.7c00 BootROM memory allocations (15KiB) + * 0x4007.fffc BootROM stack top + * + * The address space between 0x4007.fffc and 0x400f.fff is not locked in + * L2 cache thus cannot be used. + */ + +/* SPL */ +/* Defines for SPL */ +#define CONFIG_SPL_FRAMEWORK +#define CONFIG_SPL_TEXT_BASE 0x40004030 +#define CONFIG_SPL_MAX_SIZE ((128 << 10) - 0x4030) + +#define CONFIG_SPL_BSS_START_ADDR (0x40000000 + (128 << 10)) +#define CONFIG_SPL_BSS_MAX_SIZE (16 << 10) + +#ifdef CONFIG_SPL_BUILD +#define CONFIG_SYS_MALLOC_SIMPLE +#endif + +#define CONFIG_SPL_STACK (0x40000000 + ((192 - 16) << 10)) +#define CONFIG_SPL_BOOTROM_SAVE (CONFIG_SPL_STACK + 4) + +#define CONFIG_SPL_LIBCOMMON_SUPPORT +#define CONFIG_SPL_LIBGENERIC_SUPPORT +#define CONFIG_SPL_SERIAL_SUPPORT +#define CONFIG_SPL_I2C_SUPPORT + +/* SPL related SPI defines */ +#define CONFIG_SPL_SPI_SUPPORT +#define CONFIG_SPL_SPI_FLASH_SUPPORT +#define CONFIG_SPL_SPI_LOAD +#define CONFIG_SPL_SPI_BUS 0 +#define CONFIG_SPL_SPI_CS 0 +#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x24000 + +/* DS414 bus width is 32bits */ +#define CONFIG_DDR_32BIT + +/* Use random ethernet address if not configured */ +#define CONFIG_LIB_RAND +#define CONFIG_NET_RANDOM_ETHADDR + +/* Default Environment */ +#define CONFIG_BOOTCOMMAND "sf read ${loadaddr} 0xd0000 0x700000; bootm" +#define CONFIG_BOOTARGS "console=ttyS0,115200" +#define CONFIG_LOADADDR 0x80000 +#undef CONFIG_PREBOOT /* override preboot for USB and SPI flash init */ +#define CONFIG_PREBOOT "usb start; sf probe" + +#endif /* _CONFIG_SYNOLOGY_DS414_H */ |