summaryrefslogtreecommitdiff
diff options
context:
space:
mode:
-rw-r--r--drivers/video/Kconfig4
-rw-r--r--drivers/video/ssd2828.c20
-rw-r--r--drivers/video/ssd2828.h11
3 files changed, 28 insertions, 7 deletions
diff --git a/drivers/video/Kconfig b/drivers/video/Kconfig
index ec14a37..d9d4afc 100644
--- a/drivers/video/Kconfig
+++ b/drivers/video/Kconfig
@@ -19,12 +19,14 @@ config VIDEO_LCD_SSD2828
config VIDEO_LCD_SSD2828_TX_CLK
int "SSD2828 TX_CLK frequency (in MHz)"
depends on VIDEO_LCD_SSD2828
+ default 0
---help---
The frequency of the crystal, which is clocking SSD2828. It may be
anything in the 8MHz-30MHz range and the exact value should be
retrieved from the board schematics. Or in the case of Allwinner
hardware, it can be usually found as 'lcd_xtal_freq' variable in
- FEX files.
+ FEX files. It can be also set to 0 for selecting PCLK from the
+ parallel LCD interface instead of TX_CLK as the PLL clock source.
config VIDEO_LCD_SSD2828_RESET
string "RESET pin of SSD2828"
diff --git a/drivers/video/ssd2828.c b/drivers/video/ssd2828.c
index be68d38..8b09082 100644
--- a/drivers/video/ssd2828.c
+++ b/drivers/video/ssd2828.c
@@ -340,7 +340,7 @@ static int ssd2828_configure_video_interface(const struct ssd2828_config *cfg,
int ssd2828_init(const struct ssd2828_config *cfg,
const struct ctfb_res_modes *mode)
{
- u32 lp_div, pll_freq_kbps, pll_config;
+ u32 lp_div, pll_freq_kbps, reference_freq_khz, pll_config;
/* The LP clock speed is limited by 10MHz */
const u32 mipi_dsi_low_power_clk_khz = 10000;
/*
@@ -374,6 +374,20 @@ int ssd2828_init(const struct ssd2828_config *cfg,
}
/*
+ * Pick the reference clock for PLL. If we know the exact 'tx_clk'
+ * clock speed, then everything is good. If not, then we can fallback
+ * to 'pclk' (pixel clock from the parallel LCD interface). In the
+ * case of using this fallback, it is necessary to have parallel LCD
+ * already initialized and running at this point.
+ */
+ reference_freq_khz = cfg->ssd2828_tx_clk_khz;
+ if (reference_freq_khz == 0) {
+ reference_freq_khz = mode->pixclock_khz;
+ /* Use 'pclk' as the reference clock for PLL */
+ cfgr_reg |= SSD2828_CFGR_CSS;
+ }
+
+ /*
* Setup the parallel LCD timings in the appropriate registers.
*/
if (ssd2828_configure_video_interface(cfg, mode) != 0) {
@@ -390,10 +404,10 @@ int ssd2828_init(const struct ssd2828_config *cfg,
/* PLL Configuration Register */
pll_config = construct_pll_config(
cfg->mipi_dsi_bitrate_per_data_lane_mbps * 1000,
- cfg->ssd2828_tx_clk_khz);
+ reference_freq_khz);
write_hw_register(cfg, SSD2828_PLCR, pll_config);
- pll_freq_kbps = decode_pll_config(pll_config, cfg->ssd2828_tx_clk_khz);
+ pll_freq_kbps = decode_pll_config(pll_config, reference_freq_khz);
lp_div = DIV_ROUND_UP(pll_freq_kbps, mipi_dsi_low_power_clk_khz * 8);
/* VC Control Register */
diff --git a/drivers/video/ssd2828.h b/drivers/video/ssd2828.h
index 14b96c5..1af6fa4 100644
--- a/drivers/video/ssd2828.h
+++ b/drivers/video/ssd2828.h
@@ -47,8 +47,12 @@ struct ssd2828_config {
* to TX_CLK_XIO/TX_CLK_XIN pins), which is necessary at least for
* clocking SPI after reset. The exact clock speed is not strictly,
* defined, but the datasheet says that it must be somewhere in the
- * 8MHz - 30MHz range (see "TX_CLK Timing" section). It is used as
- * a reference clock for PLL and must be set correctly.
+ * 8MHz - 30MHz range (see "TX_CLK Timing" section). It can be also
+ * used as a reference clock for PLL. If the exact clock frequency
+ * is known, then it can be specified here. If it is unknown, or the
+ * information is not trustworthy, then it can be set to 0.
+ *
+ * If unsure, set to 0.
*/
int ssd2828_tx_clk_khz;
@@ -115,7 +119,8 @@ struct ssd2828_config {
* The right place to insert this function call is after the parallel LCD
* interface is initialized and before turning on the backlight. This is
* advised in the "Example for system sleep in and out" section of the
- * SSD2828 datasheet.
+ * SSD2828 datasheet. And also SS2828 may use 'pclk' as the clock source
+ * for PLL, which means that the input signal must be already there.
*/
int ssd2828_init(const struct ssd2828_config *cfg,
const struct ctfb_res_modes *mode);