summaryrefslogtreecommitdiff
diff options
context:
space:
mode:
-rw-r--r--board/sbc8548/law.c8
-rw-r--r--board/sbc8548/sbc8548.c2
-rw-r--r--board/sbc8548/tlb.c19
-rw-r--r--doc/README.sbc854834
-rw-r--r--include/configs/sbc8548.h106
5 files changed, 142 insertions, 27 deletions
diff --git a/board/sbc8548/law.c b/board/sbc8548/law.c
index febb682..c263191 100644
--- a/board/sbc8548/law.c
+++ b/board/sbc8548/law.c
@@ -41,13 +41,21 @@
* 0xf8b0_0000 0xf80f_ffff EEPROM 1M
* 0xff80_0000 0xffff_ffff FLASH (boot bank) 8M
*
+ * If swapped CS0/CS6 via JP12+SW2.8:
+ * 0xef80_0000 0xefff_ffff FLASH (2nd bank) 8M
+ * 0xfc00_0000 0xffff_ffff FLASH (boot bank) 64M
+ *
* Notes:
* CCSRBAR and L2-as-SRAM don't need a configured Local Access Window.
* If flash is 8M at default position (last 8M), no LAW needed.
*/
struct law_entry law_table[] = {
+#ifdef CONFIG_SYS_ALT_BOOT
+ SET_LAW(CONFIG_SYS_ALT_FLASH, LAW_SIZE_8M, LAW_TRGT_IF_LBC),
+#else
SET_LAW(CONFIG_SYS_ALT_FLASH, LAW_SIZE_64M, LAW_TRGT_IF_LBC),
+#endif
#ifndef CONFIG_SPD_EEPROM
SET_LAW(CONFIG_SYS_DDR_SDRAM_BASE, LAW_SIZE_256M, LAW_TRGT_IF_DDR),
#endif
diff --git a/board/sbc8548/sbc8548.c b/board/sbc8548/sbc8548.c
index 26095a5..63d504d 100644
--- a/board/sbc8548/sbc8548.c
+++ b/board/sbc8548/sbc8548.c
@@ -113,7 +113,7 @@ void lbc_sdram_init(void)
puts(" SDRAM: ");
- print_size (CONFIG_SYS_LBC_SDRAM_SIZE * 1024 * 1024, "\n");
+ print_size(CONFIG_SYS_LBC_SDRAM_SIZE * 1024 * 1024, "\n");
/*
* Setup SDRAM Base and Option Registers
diff --git a/board/sbc8548/tlb.c b/board/sbc8548/tlb.c
index e9cedc7..4bf7214 100644
--- a/board/sbc8548/tlb.c
+++ b/board/sbc8548/tlb.c
@@ -104,6 +104,7 @@ struct fsl_e_tlb_entry tlb_table[] = {
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
0, 5, BOOKE_PAGESZ_16M, 1),
+#ifndef CONFIG_SYS_ALT_BOOT
/*
* TLB 6: 64M Non-cacheable, guarded
* 0xec000000 64M 64MB user FLASH
@@ -111,6 +112,24 @@ struct fsl_e_tlb_entry tlb_table[] = {
SET_TLB_ENTRY(1, CONFIG_SYS_ALT_FLASH, CONFIG_SYS_ALT_FLASH,
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
0, 6, BOOKE_PAGESZ_64M, 1),
+#else
+ /*
+ * TLB 6: 4M Non-cacheable, guarded
+ * 0xef800000 4M 1st 1/2 8MB soldered FLASH
+ */
+ SET_TLB_ENTRY(1, CONFIG_SYS_ALT_FLASH, CONFIG_SYS_ALT_FLASH,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 6, BOOKE_PAGESZ_4M, 1),
+
+ /*
+ * TLB 7: 4M Non-cacheable, guarded
+ * 0xefc00000 4M 2nd half 8MB soldered FLASH
+ */
+ SET_TLB_ENTRY(1, CONFIG_SYS_ALT_FLASH + 0x400000,
+ CONFIG_SYS_ALT_FLASH + 0x400000,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 7, BOOKE_PAGESZ_4M, 1),
+#endif
};
diff --git a/doc/README.sbc8548 b/doc/README.sbc8548
index 5fa9c93..e6b8abe 100644
--- a/doc/README.sbc8548
+++ b/doc/README.sbc8548
@@ -86,6 +86,33 @@ The "md" steps in the above are just a precautionary step that allow
you to confirm the u-boot version that was downloaded, and then confirm
that it was copied to flash.
+The above assumes that you are using the default board settings which
+have u-boot in the 8MB flash, tied to /CS0.
+
+If you are running the default 8MB /CS0 settings but want to store an
+image in the SODIMM that is built with CONFIG_SYS_ALT_BOOT enabled,
+(as a backup, etc) then the steps will become:
+
+ tftp u-boot.bin
+ md 200000 10
+ protect off all
+ era eff00000 efffffff
+ cp.b 200000 eff00000 100000
+ md eff00000 10
+ protect on all
+
+Finally, if you are running the alternate 64MB /CS0 settings and want
+to update the in-use u-boot image, then (again with CONFIG_SYS_ALT_BOOT
+enabled) the steps will become:
+
+ tftp u-boot.bin
+ md 200000 10
+ protect off all
+ era fff00000 ffffffff
+ cp.b 200000 fff00000 100000
+ md fff00000 10
+ protect on all
+
Hardware Reference:
===================
@@ -127,10 +154,9 @@ JP19 PCI mode PCI PCI-X
onto /CS0 and the SODIMM flash on /CS6 (default). When JP12
is jumpered parallel to the LBC-SDRAM, then /CS0 is for the
SODIMM flash and /CS6 is for the boot flash. Note that in this
-alternate setting, you also need to switch SW2.8 to ON. Currently
-u-boot doesn't support booting off the SODIMM in this alternate
-setting without manually altering BR0/OR0 and BR6/OR6 in the
-board config file appropriately.
+alternate setting, you also need to switch SW2.8 to ON.
+See the setting CONFIG_SYS_ALT_BOOT if you want to use this setting
+and boot u-boot from the 64MB SODIMM
Switches:
diff --git a/include/configs/sbc8548.h b/include/configs/sbc8548.h
index cea0179..fb07d09 100644
--- a/include/configs/sbc8548.h
+++ b/include/configs/sbc8548.h
@@ -57,9 +57,19 @@
#define CONFIG_MPC8548 1 /* MPC8548 specific */
#define CONFIG_SBC8548 1 /* SBC8548 board specific */
+/*
+ * If you want to boot from the SODIMM flash, instead of the soldered
+ * on flash, set this, and change JP12, SW2:8 accordingly.
+ */
+#undef CONFIG_SYS_ALT_BOOT
+
#ifndef CONFIG_SYS_TEXT_BASE
+#ifdef CONFIG_SYS_ALT_BOOT
+#define CONFIG_SYS_TEXT_BASE 0xfff00000
+#else
#define CONFIG_SYS_TEXT_BASE 0xfffa0000
#endif
+#endif
#undef CONFIG_RIO
@@ -139,28 +149,54 @@
/*
* FLASH on the Local Bus
* Two banks, one 8MB the other 64MB, using the CFI driver.
- * Boot from BR0/OR0 bank at 0xff80_0000
- * Alternate BR6/OR6 bank at 0xec00_0000
+ * JP12+SW2.8 are used to swap CS0 and CS6, defaults are to have
+ * CS0 the 8MB boot flash, and CS6 the 64MB flash.
*
- * BR0:
+ * Default:
+ * ec00_0000 efff_ffff 64MB SODIMM
+ * ff80_0000 ffff_ffff 8MB soldered flash
+ *
+ * Alternate:
+ * ef80_0000 efff_ffff 8MB soldered flash
+ * fc00_0000 ffff_ffff 64MB SODIMM
+ *
+ * BR0_8M:
* Base address 0 = 0xff80_0000 = BR0[0:16] = 1111 1111 1000 0000 0
* Port Size = 8 bits = BRx[19:20] = 01
* Use GPCM = BRx[24:26] = 000
* Valid = BRx[31] = 1
*
- * 0 4 8 12 16 20 24 28
- * 1111 1111 1000 0000 0000 1000 0000 0001 = ff800801 BR0
- *
- * BR6:
- * Base address 6 = 0xec00_0000 = BR6[0:16] = 1110 1100 0000 0000 0
+ * BR0_64M:
+ * Base address 0 = 0xfc00_0000 = BR0[0:16] = 1111 1100 0000 0000 0
* Port Size = 32 bits = BRx[19:20] = 11
+ *
+ * 0 4 8 12 16 20 24 28
+ * 1111 1111 1000 0000 0000 1000 0000 0001 = ff800801 BR0_8M
+ * 1111 1100 0000 0000 0001 1000 0000 0001 = fc001801 BR0_64M
+ */
+#define CONFIG_SYS_BR0_8M 0xff800801
+#define CONFIG_SYS_BR0_64M 0xfc001801
+
+/*
+ * BR6_8M:
+ * Base address 6 = 0xef80_0000 = BR6[0:16] = 1110 1111 1000 0000 0
+ * Port Size = 8 bits = BRx[19:20] = 01
* Use GPCM = BRx[24:26] = 000
* Valid = BRx[31] = 1
+
+ * BR6_64M:
+ * Base address 6 = 0xec00_0000 = BR6[0:16] = 1110 1100 0000 0000 0
+ * Port Size = 32 bits = BRx[19:20] = 11
*
* 0 4 8 12 16 20 24 28
- * 1110 1100 0000 0000 0001 1000 0000 0001 = ec001801 BR6
- *
- * OR0:
+ * 1110 1111 1000 0000 0000 1000 0000 0001 = ef800801 BR6_8M
+ * 1110 1100 0000 0000 0001 1000 0000 0001 = ec001801 BR6_64M
+ */
+#define CONFIG_SYS_BR6_8M 0xef800801
+#define CONFIG_SYS_BR6_64M 0xec001801
+
+/*
+ * OR0_8M:
* Addr Mask = 8M = OR1[0:16] = 1111 1111 1000 0000 0
* XAM = OR0[17:18] = 11
* CSNT = OR0[20] = 1
@@ -169,11 +205,20 @@
* TRLX = use relaxed timing = OR0[29] = 1
* EAD = use external address latch delay = OR0[31] = 1
*
- * 0 4 8 12 16 20 24 28
- * 1111 1111 1000 0000 0110 1110 0110 0101 = ff806e65 OR0
+ * OR0_64M:
+ * Addr Mask = 64M = OR1[0:16] = 1111 1100 0000 0000 0
*
- * OR6:
- * Addr Mask = 64M = OR6[0:16] = 1111 1100 0000 0000 0
+ *
+ * 0 4 8 12 16 20 24 28
+ * 1111 1111 1000 0000 0110 1110 0110 0101 = ff806e65 OR0_8M
+ * 1111 1100 0000 0000 0110 1110 0110 0101 = fc006e65 OR0_64M
+ */
+#define CONFIG_SYS_OR0_8M 0xff806e65
+#define CONFIG_SYS_OR0_64M 0xfc006e65
+
+/*
+ * OR6_8M:
+ * Addr Mask = 8M = OR6[0:16] = 1111 1111 1000 0000 0
* XAM = OR6[17:18] = 11
* CSNT = OR6[20] = 1
* ACS = half cycle delay = OR6[21:22] = 11
@@ -181,20 +226,37 @@
* TRLX = use relaxed timing = OR6[29] = 1
* EAD = use external address latch delay = OR6[31] = 1
*
+ * OR6_64M:
+ * Addr Mask = 64M = OR6[0:16] = 1111 1100 0000 0000 0
+ *
* 0 4 8 12 16 20 24 28
- * 1111 1100 0000 0000 0110 1110 0110 0101 = fc006e65 OR6
+ * 1111 1111 1000 0000 0110 1110 0110 0101 = ff806e65 OR6_8M
+ * 1111 1100 0000 0000 0110 1110 0110 0101 = fc006e65 OR6_64M
*/
+#define CONFIG_SYS_OR6_8M 0xff806e65
+#define CONFIG_SYS_OR6_64M 0xfc006e65
+#ifndef CONFIG_SYS_ALT_BOOT /* JP12 in default position */
#define CONFIG_SYS_BOOT_BLOCK 0xff800000 /* start of 8MB Flash */
#define CONFIG_SYS_ALT_FLASH 0xec000000 /* 64MB "user" flash */
-#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_BOOT_BLOCK /* start of FLASH 16M */
-#define CONFIG_SYS_BR0_PRELIM 0xff800801
-#define CONFIG_SYS_BR6_PRELIM 0xec001801
+#define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_BR0_8M
+#define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_OR0_8M
+
+#define CONFIG_SYS_BR6_PRELIM CONFIG_SYS_BR6_64M
+#define CONFIG_SYS_OR6_PRELIM CONFIG_SYS_OR6_64M
+#else /* JP12 in alternate position */
+#define CONFIG_SYS_BOOT_BLOCK 0xfc000000 /* start 64MB Flash */
+#define CONFIG_SYS_ALT_FLASH 0xef800000 /* 8MB soldered flash */
-#define CONFIG_SYS_OR0_PRELIM 0xff806e65
-#define CONFIG_SYS_OR6_PRELIM 0xfc006e65
+#define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_BR0_64M
+#define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_OR0_64M
+
+#define CONFIG_SYS_BR6_PRELIM CONFIG_SYS_BR6_8M
+#define CONFIG_SYS_OR6_PRELIM CONFIG_SYS_OR6_8M
+#endif
+#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_BOOT_BLOCK
#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE, \
CONFIG_SYS_ALT_FLASH}
#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */
@@ -330,7 +392,7 @@
* thing for MONITOR_LEN in both cases.
*/
#define CONFIG_SYS_MONITOR_LEN (~CONFIG_SYS_TEXT_BASE + 1)
-#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
+#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */
/* Serial Port */
#define CONFIG_CONS_INDEX 1