summaryrefslogtreecommitdiff
diff options
context:
space:
mode:
-rw-r--r--board/freescale/mx28evk/README22
-rw-r--r--doc/README.mxs26
2 files changed, 45 insertions, 3 deletions
diff --git a/board/freescale/mx28evk/README b/board/freescale/mx28evk/README
index 0389a1d..958ebc6 100644
--- a/board/freescale/mx28evk/README
+++ b/board/freescale/mx28evk/README
@@ -23,11 +23,19 @@ To boot MX28EVK from an SD card, set the boot mode DIP switches as:
* VDD 5V: To the left (off)
* Hold Button: Down (off)
+To boot MX28EVK from SPI NOR flash, set the boot mode DIP switches as:
+
+ * Boot Mode Select: 0 0 1 0 (Boot from SSP2)
+ * JTAG PSWITCH RESET: To the right (reset disabled)
+ * Battery Source: Down
+ * Wall 5V: Up
+ * VDD 5V: To the left (off)
+ * Hold Button: Down (off)
Environment Storage
-------------------
-There are two targets for mx28evk:
+There are three targets for mx28evk:
"make mx28evk_config" - store environment variables into MMC
@@ -35,12 +43,20 @@ or
"make mx28evk_nand_config" - store environment variables into NAND flash
+or
+
+"make mx28evk_spi_config" - store enviroment variables into SPI NOR flash
+
Choose the target accordingly.
Note: The mx28evk board does not come with a NAND flash populated from the
factory. It comes with an empty slot (U23), which allows the insertion of a
48-pin TSOP flash device.
-Follow the instructions from doc/README.mxs to generate a bootable SD card.
+mx28evk does not come with SPI NOR flash populated from the factory either.
+It is possible to solder a SOIC memory on U49 or use a DIP8 on J89.
+To get SPI communication to work R320, R321,R322 and C178 need to be populated.
+Look in the schematics for the proper component values.
-Insert the SD card in slot 0, power up the board and U-boot will boot.
+Follow the instructions from doc/README.mxs to generate a bootable SD card or
+to generate a binary to be flashed into SPI NOR.
diff --git a/doc/README.mxs b/doc/README.mxs
index 0235a5a..ed2e568 100644
--- a/doc/README.mxs
+++ b/doc/README.mxs
@@ -23,6 +23,7 @@ Contents
2) Compiling U-Boot for a MXS based board
3) Installation of U-Boot for a MXS based board to SD card
4) Installation of U-Boot into NAND flash on a MX28 based board
+5) Installation of U-boot into SPI NOR flash on a MX28 based board
1) Prerequisites
----------------
@@ -262,3 +263,28 @@ There are two possibilities when preparing an image writable to NAND flash.
In case the user needs to boot a firmware image bigger than 1Mb, the
user has to adjust the "update_nand_firmware_maxsz" variable for the
update scripts to work properly.
+
+5) Installation of U-Boot into SPI NOR flash on a MX28 based board
+------------------------------------------------------------------
+
+The u-boot.sb file can be directly written to SPI NOR from U-boot prompt.
+
+Load u-boot.sb into RAM, this can be done in several ways and one way is to use
+tftp:
+ => tftp u-boot.sb 0x42000000
+
+Probe the SPI NOR flash:
+ => sf probe
+
+(SPI NOR should be succesfully detected in this step)
+
+Erase the blocks where U-boot binary will be written to:
+ => sf erase 0x0 0x80000
+
+Write u-boot.sb to SPI NOR:
+ => sf write 0x42000000 0 0x80000
+
+Power off the board and set the boot mode DIP switches to boot from the SPI NOR
+according to MX28 manual section 12.2.1 (Table 12-2)
+
+Last step is to power up the board and U-boot should start from SPI NOR.