diff options
Diffstat (limited to 'README')
| -rw-r--r-- | README | 33 |
1 files changed, 30 insertions, 3 deletions
@@ -201,7 +201,6 @@ Directory Hierarchy: /mpc5xx Files specific to Freescale MPC5xx CPUs /mpc5xxx Files specific to Freescale MPC5xxx CPUs /mpc8xx Files specific to Freescale MPC8xx CPUs - /mpc8220 Files specific to Freescale MPC8220 CPUs /mpc824x Files specific to Freescale MPC824x CPUs /mpc8260 Files specific to Freescale MPC8260 CPUs /mpc85xx Files specific to Freescale MPC85xx CPUs @@ -844,6 +843,7 @@ The following options need to be configured: CONFIG_CMD_FDOS * Dos diskette Support CONFIG_CMD_FLASH flinfo, erase, protect CONFIG_CMD_FPGA FPGA device initialization support + CONFIG_CMD_FUSE Device fuse support CONFIG_CMD_GETTIME * Get time since boot CONFIG_CMD_GO * the 'go' command (exec code) CONFIG_CMD_GREPENV * search environment @@ -898,6 +898,7 @@ The following options need to be configured: CONFIG_CMD_SF * Read/write/erase SPI NOR flash CONFIG_CMD_SHA1SUM print sha1 memory digest (requires CONFIG_CMD_MEMORY) + CONFIG_CMD_SOFTSWITCH * Soft switch setting command for BF60x CONFIG_CMD_SOURCE "source" command Support CONFIG_CMD_SPI * SPI serial bus support CONFIG_CMD_TFTPSRV * TFTP transfer in server mode @@ -1208,7 +1209,23 @@ The following options need to be configured: If this option is set, the driver enables cache flush. - TPM Support: - CONFIG_GENERIC_LPC_TPM + CONFIG_TPM + Support TPM devices. + + CONFIG_TPM_TIS_I2C + Support for i2c bus TPM devices. Only one device + per system is supported at this time. + + CONFIG_TPM_TIS_I2C_BUS_NUMBER + Define the the i2c bus number for the TPM device + + CONFIG_TPM_TIS_I2C_SLAVE_ADDRESS + Define the TPM's address on the i2c bus + + CONFIG_TPM_TIS_I2C_BURST_LIMITATION + Define the burst count bytes upper limit + + CONFIG_TPM_TIS_LPC Support for generic parallel port TPM devices. Only one device per system is supported at this time. @@ -2996,6 +3013,12 @@ FIT uImage format: use an arch-specific makefile fragment instead, for example if more than one image needs to be produced. + CONFIG_FIT_SPL_PRINT + Printing information about a FIT image adds quite a bit of + code to SPL. So this is normally disabled in SPL. Use this + option to re-enable it. This will affect the output of the + bootm command when booting a FIT image. + Modem Support: -------------- @@ -3339,6 +3362,10 @@ Configuration Settings: offset _bss_start_ofs from CONFIG_SYS_TEXT_BASE, rather than directly. You should not need to touch this setting. +- CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC (OMAP only) + This is set by OMAP boards for the max time that reset should + be asserted. See doc/README.omap-reset-time for details on how + the value can be calulated on a given board. The following definitions that deal with the placement and management of environment data (variable area); in general, we support the @@ -5057,7 +5084,7 @@ On some platforms, it's possible to boot Linux zImage. This is done using the "bootz" command. The syntax of "bootz" command is the same as the syntax of "bootm" command. -Note, defining the CONFIG_SUPPORT_INITRD_RAW allows user to supply +Note, defining the CONFIG_SUPPORT_RAW_INITRD allows user to supply kernel with raw initrd images. The syntax is slightly different, the address of the initrd must be augmented by it's size, in the following format: "<initrd addres>:<initrd size>". |