diff options
Diffstat (limited to 'README')
| -rw-r--r-- | README | 66 |
1 files changed, 66 insertions, 0 deletions
@@ -264,6 +264,17 @@ e.g. "make cogent_mpc8xx_config". And also configure the cogent directory according to the instructions in cogent/README. +Sandbox Environment: +-------------------- + +U-Boot can be built natively to run on a Linux host using the 'sandbox' +board. This allows feature development which is not board- or architecture- +specific to be undertaken on a native platform. The sandbox is also used to +run some of U-Boot's tests. + +See board/sandbox/sandbox/README.sandbox for more details. + + Configuration Options: ---------------------- @@ -440,6 +451,12 @@ The following options need to be configured: supported, core will start to execute uboot when wakes up. - Generic CPU options: + CONFIG_SYS_GENERIC_GLOBAL_DATA + Defines global data is initialized in generic board board_init_f(). + If this macro is defined, global data is created and cleared in + generic board board_init_f(). Without this macro, architecture/board + should initialize global data before calling board_init_f(). + CONFIG_SYS_BIG_ENDIAN, CONFIG_SYS_LITTLE_ENDIAN Defines the endianess of the CPU. Implementation of those @@ -740,6 +757,10 @@ The following options need to be configured: boot loader that has already initialized the UART. Define this variable to flush the UART at init time. + CONFIG_SERIAL_HW_FLOW_CONTROL + + Define this variable to enable hw flow control in serial driver. + Current user of this option is drivers/serial/nsl16550.c driver - Console Interface: Depending on board, define exactly one serial port @@ -1513,6 +1534,16 @@ The following options need to be configured: CONFIG_SH_MMCIF_CLK Define the clock frequency for MMCIF + CONFIG_GENERIC_MMC + Enable the generic MMC driver + + CONFIG_SUPPORT_EMMC_BOOT + Enable some additional features of the eMMC boot partitions. + + CONFIG_SUPPORT_EMMC_RPMB + Enable the commands for reading, writing and programming the + key for the Replay Protection Memory Block partition in eMMC. + - USB Device Firmware Update (DFU) class support: CONFIG_DFU_FUNCTION This enables the USB portion of the DFU USB class @@ -1558,6 +1589,28 @@ The following options need to be configured: entering dfuMANIFEST state. Host waits this timeout, before sending again an USB request to the device. +- USB Device Android Fastboot support: + CONFIG_CMD_FASTBOOT + This enables the command "fastboot" which enables the Android + fastboot mode for the platform's USB device. Fastboot is a USB + protocol for downloading images, flashing and device control + used on Android devices. + See doc/README.android-fastboot for more information. + + CONFIG_ANDROID_BOOT_IMAGE + This enables support for booting images which use the Android + image format header. + + CONFIG_USB_FASTBOOT_BUF_ADDR + The fastboot protocol requires a large memory buffer for + downloads. Define this to the starting RAM address to use for + downloaded images. + + CONFIG_USB_FASTBOOT_BUF_SIZE + The fastboot protocol requires a large memory buffer for + downloads. This buffer should be as large as possible for a + platform. Define this to the size available RAM for fastboot. + - Journaling Flash filesystem support: CONFIG_JFFS2_NAND, CONFIG_JFFS2_NAND_OFF, CONFIG_JFFS2_NAND_SIZE, CONFIG_JFFS2_NAND_DEV @@ -2529,6 +2582,19 @@ CBFS (Coreboot Filesystem) support Specify the number of FPGA devices to support. + CONFIG_CMD_FPGA_LOADMK + + Enable support for fpga loadmk command + + CONFIG_CMD_FPGA_LOADP + + Enable support for fpga loadp command - load partial bitstream + + CONFIG_CMD_FPGA_LOADBP + + Enable support for fpga loadbp command - load partial bitstream + (Xilinx only) + CONFIG_SYS_FPGA_PROG_FEEDBACK Enable printing of hash marks during FPGA configuration. |