diff options
Diffstat (limited to 'arch/arm/dts/meson-gxbb.dtsi')
-rw-r--r-- | arch/arm/dts/meson-gxbb.dtsi | 718 |
1 files changed, 444 insertions, 274 deletions
diff --git a/arch/arm/dts/meson-gxbb.dtsi b/arch/arm/dts/meson-gxbb.dtsi index e502c24..39a774a 100644 --- a/arch/arm/dts/meson-gxbb.dtsi +++ b/arch/arm/dts/meson-gxbb.dtsi @@ -40,307 +40,477 @@ * OTHER DEALINGS IN THE SOFTWARE. */ -#include <dt-bindings/gpio/gpio.h> -#include <dt-bindings/interrupt-controller/irq.h> -#include <dt-bindings/interrupt-controller/arm-gic.h> +#include "meson-gx.dtsi" #include <dt-bindings/gpio/meson-gxbb-gpio.h> #include <dt-bindings/reset/amlogic,meson-gxbb-reset.h> +#include <dt-bindings/clock/gxbb-clkc.h> +#include <dt-bindings/clock/gxbb-aoclkc.h> +#include <dt-bindings/reset/gxbb-aoclkc.h> / { compatible = "amlogic,meson-gxbb"; - interrupt-parent = <&gic>; - #address-cells = <2>; - #size-cells = <2>; - cpus { - #address-cells = <0x2>; - #size-cells = <0x0>; - - cpu0: cpu@0 { - device_type = "cpu"; - compatible = "arm,cortex-a53", "arm,armv8"; - reg = <0x0 0x0>; - enable-method = "psci"; + soc { + usb0_phy: phy@c0000000 { + compatible = "amlogic,meson-gxbb-usb2-phy"; + #phy-cells = <0>; + reg = <0x0 0xc0000000 0x0 0x20>; + resets = <&reset RESET_USB_OTG>; + clocks = <&clkc CLKID_USB>, <&clkc CLKID_USB0>; + clock-names = "usb_general", "usb"; + status = "disabled"; }; - cpu1: cpu@1 { - device_type = "cpu"; - compatible = "arm,cortex-a53", "arm,armv8"; - reg = <0x0 0x1>; - enable-method = "psci"; + usb1_phy: phy@c0000020 { + compatible = "amlogic,meson-gxbb-usb2-phy"; + #phy-cells = <0>; + reg = <0x0 0xc0000020 0x0 0x20>; + resets = <&reset RESET_USB_OTG>; + clocks = <&clkc CLKID_USB>, <&clkc CLKID_USB1>; + clock-names = "usb_general", "usb"; + status = "disabled"; }; - cpu2: cpu@2 { - device_type = "cpu"; - compatible = "arm,cortex-a53", "arm,armv8"; - reg = <0x0 0x2>; - enable-method = "psci"; + usb0: usb@c9000000 { + compatible = "amlogic,meson-gxbb-usb", "snps,dwc2"; + reg = <0x0 0xc9000000 0x0 0x40000>; + interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clkc CLKID_USB0_DDR_BRIDGE>; + clock-names = "otg"; + phys = <&usb0_phy>; + phy-names = "usb2-phy"; + dr_mode = "host"; + status = "disabled"; }; - cpu3: cpu@3 { - device_type = "cpu"; - compatible = "arm,cortex-a53", "arm,armv8"; - reg = <0x0 0x3>; - enable-method = "psci"; + usb1: usb@c9100000 { + compatible = "amlogic,meson-gxbb-usb", "snps,dwc2"; + reg = <0x0 0xc9100000 0x0 0x40000>; + interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clkc CLKID_USB1_DDR_BRIDGE>; + clock-names = "otg"; + phys = <&usb1_phy>; + phy-names = "usb2-phy"; + dr_mode = "host"; + status = "disabled"; }; }; +}; - arm-pmu { - compatible = "arm,cortex-a53-pmu"; - interrupts = <GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>; - interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>; +&cbus { + spifc: spi@8c80 { + compatible = "amlogic,meson-gxbb-spifc"; + reg = <0x0 0x08c80 0x0 0x80>; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&clkc CLKID_SPI>; + status = "disabled"; }; +}; + +ðmac { + clocks = <&clkc CLKID_ETH>, + <&clkc CLKID_FCLK_DIV2>, + <&clkc CLKID_MPLL2>; + clock-names = "stmmaceth", "clkin0", "clkin1"; +}; + +&aobus { + pinctrl_aobus: pinctrl@14 { + compatible = "amlogic,meson-gxbb-aobus-pinctrl"; + #address-cells = <2>; + #size-cells = <2>; + ranges; + + gpio_ao: bank@14 { + reg = <0x0 0x00014 0x0 0x8>, + <0x0 0x0002c 0x0 0x4>, + <0x0 0x00024 0x0 0x8>; + reg-names = "mux", "pull", "gpio"; + gpio-controller; + #gpio-cells = <2>; + }; + + uart_ao_a_pins: uart_ao_a { + mux { + groups = "uart_tx_ao_a", "uart_rx_ao_a"; + function = "uart_ao"; + }; + }; + + uart_ao_a_cts_rts_pins: uart_ao_a_cts_rts { + mux { + groups = "uart_cts_ao_a", + "uart_rts_ao_a"; + function = "uart_ao"; + }; + }; + + uart_ao_b_pins: uart_ao_b { + mux { + groups = "uart_tx_ao_b", "uart_rx_ao_b"; + function = "uart_ao_b"; + }; + }; + + uart_ao_b_cts_rts_pins: uart_ao_b_cts_rts { + mux { + groups = "uart_cts_ao_b", + "uart_rts_ao_b"; + function = "uart_ao_b"; + }; + }; - psci { - compatible = "arm,psci-0.2"; - method = "smc"; + remote_input_ao_pins: remote_input_ao { + mux { + groups = "remote_input_ao"; + function = "remote_input_ao"; + }; + }; + + i2c_ao_pins: i2c_ao { + mux { + groups = "i2c_sck_ao", + "i2c_sda_ao"; + function = "i2c_ao"; + }; + }; + + pwm_ao_a_3_pins: pwm_ao_a_3 { + mux { + groups = "pwm_ao_a_3"; + function = "pwm_ao_a_3"; + }; + }; + + pwm_ao_a_6_pins: pwm_ao_a_6 { + mux { + groups = "pwm_ao_a_6"; + function = "pwm_ao_a_6"; + }; + }; + + pwm_ao_a_12_pins: pwm_ao_a_12 { + mux { + groups = "pwm_ao_a_12"; + function = "pwm_ao_a_12"; + }; + }; + + pwm_ao_b_pins: pwm_ao_b { + mux { + groups = "pwm_ao_b"; + function = "pwm_ao_b"; + }; + }; }; - timer { - compatible = "arm,armv8-timer"; - interrupts = <GIC_PPI 13 - (GIC_CPU_MASK_RAW(0xff) | IRQ_TYPE_EDGE_RISING)>, - <GIC_PPI 14 - (GIC_CPU_MASK_RAW(0xff) | IRQ_TYPE_EDGE_RISING)>, - <GIC_PPI 11 - (GIC_CPU_MASK_RAW(0xff) | IRQ_TYPE_EDGE_RISING)>, - <GIC_PPI 10 - (GIC_CPU_MASK_RAW(0xff) | IRQ_TYPE_EDGE_RISING)>; + clkc_AO: clock-controller@040 { + compatible = "amlogic,gxbb-aoclkc"; + reg = <0x0 0x00040 0x0 0x4>; + #clock-cells = <1>; + #reset-cells = <1>; }; - xtal: xtal-clk { - compatible = "fixed-clock"; - clock-frequency = <24000000>; - clock-output-names = "xtal"; - #clock-cells = <0>; + pwm_ab_AO: pwm@550 { + compatible = "amlogic,meson-gxbb-pwm"; + reg = <0x0 0x0550 0x0 0x10>; + #pwm-cells = <3>; + status = "disabled"; }; - soc { - compatible = "simple-bus"; + i2c_AO: i2c@500 { + compatible = "amlogic,meson-gxbb-i2c"; + reg = <0x0 0x500 0x0 0x20>; + interrupts = <GIC_SPI 195 IRQ_TYPE_EDGE_RISING>; + clocks = <&clkc CLKID_AO_I2C>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; +}; + +&periphs { + pinctrl_periphs: pinctrl@4b0 { + compatible = "amlogic,meson-gxbb-periphs-pinctrl"; #address-cells = <2>; #size-cells = <2>; ranges; - cbus: cbus@c1100000 { - compatible = "simple-bus"; - reg = <0x0 0xc1100000 0x0 0x100000>; - #address-cells = <2>; - #size-cells = <2>; - ranges = <0x0 0x0 0x0 0xc1100000 0x0 0x100000>; - - reset: reset-controller@4404 { - compatible = "amlogic,meson-gxbb-reset"; - reg = <0x0 0x04404 0x0 0x20>; - #reset-cells = <1>; - }; - - uart_A: serial@84c0 { - compatible = "amlogic,meson-uart"; - reg = <0x0 0x84c0 0x0 0x14>; - interrupts = <GIC_SPI 26 IRQ_TYPE_EDGE_RISING>; - clocks = <&xtal>; - status = "disabled"; - }; - - uart_B: serial@84dc { - compatible = "amlogic,meson-uart"; - reg = <0x0 0x84dc 0x0 0x14>; - interrupts = <GIC_SPI 75 IRQ_TYPE_EDGE_RISING>; - clocks = <&xtal>; - status = "disabled"; - }; - - uart_C: serial@8700 { - compatible = "amlogic,meson-uart"; - reg = <0x0 0x8700 0x0 0x14>; - interrupts = <GIC_SPI 93 IRQ_TYPE_EDGE_RISING>; - clocks = <&xtal>; - status = "disabled"; - }; - }; - - gic: interrupt-controller@c4301000 { - compatible = "arm,gic-400"; - reg = <0x0 0xc4301000 0 0x1000>, - <0x0 0xc4302000 0 0x2000>, - <0x0 0xc4304000 0 0x2000>, - <0x0 0xc4306000 0 0x2000>; - interrupt-controller; - interrupts = <GIC_PPI 9 - (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_HIGH)>; - #interrupt-cells = <3>; - #address-cells = <0>; - }; - - aobus: aobus@c8100000 { - compatible = "simple-bus"; - reg = <0x0 0xc8100000 0x0 0x100000>; - #address-cells = <2>; - #size-cells = <2>; - ranges = <0x0 0x0 0x0 0xc8100000 0x0 0x100000>; - - pinctrl_aobus: pinctrl@14 { - compatible = "amlogic,meson-gxbb-aobus-pinctrl"; - #address-cells = <2>; - #size-cells = <2>; - ranges; - - gpio_ao: bank@14 { - reg = <0x0 0x00014 0x0 0x8>, - <0x0 0x0002c 0x0 0x4>, - <0x0 0x00024 0x0 0x8>; - reg-names = "mux", "pull", "gpio"; - gpio-controller; - #gpio-cells = <2>; - }; - - uart_ao_a_pins: uart_ao_a { - mux { - groups = "uart_tx_ao_a", "uart_rx_ao_a"; - function = "uart_ao"; - }; - }; - }; - - uart_AO: serial@4c0 { - compatible = "amlogic,meson-uart"; - reg = <0x0 0x004c0 0x0 0x14>; - interrupts = <GIC_SPI 193 IRQ_TYPE_EDGE_RISING>; - clocks = <&xtal>; - status = "disabled"; - }; - }; - - periphs: periphs@c8834000 { - compatible = "simple-bus"; - reg = <0x0 0xc8834000 0x0 0x2000>; - #address-cells = <2>; - #size-cells = <2>; - ranges = <0x0 0x0 0x0 0xc8834000 0x0 0x2000>; - - rng { - compatible = "amlogic,meson-rng"; - reg = <0x0 0x0 0x0 0x4>; - }; - - pinctrl_periphs: pinctrl@4b0 { - compatible = "amlogic,meson-gxbb-periphs-pinctrl"; - #address-cells = <2>; - #size-cells = <2>; - ranges; - - gpio: bank@4b0 { - reg = <0x0 0x004b0 0x0 0x28>, - <0x0 0x004e8 0x0 0x14>, - <0x0 0x00120 0x0 0x14>, - <0x0 0x00430 0x0 0x40>; - reg-names = "mux", "pull", "pull-enable", "gpio"; - gpio-controller; - #gpio-cells = <2>; - }; - - emmc_pins: emmc { - mux { - groups = "emmc_nand_d07", - "emmc_cmd", - "emmc_clk"; - function = "emmc"; - }; - }; - - sdcard_pins: sdcard { - mux { - groups = "sdcard_d0", - "sdcard_d1", - "sdcard_d2", - "sdcard_d3", - "sdcard_cmd", - "sdcard_clk"; - function = "sdcard"; - }; - }; - - uart_a_pins: uart_a { - mux { - groups = "uart_tx_a", - "uart_rx_a"; - function = "uart_a"; - }; - }; - - uart_b_pins: uart_b { - mux { - groups = "uart_tx_b", - "uart_rx_b"; - function = "uart_b"; - }; - }; - - uart_c_pins: uart_c { - mux { - groups = "uart_tx_c", - "uart_rx_c"; - function = "uart_c"; - }; - }; - - eth_pins: eth_c { - mux { - groups = "eth_mdio", - "eth_mdc", - "eth_clk_rx_clk", - "eth_rx_dv", - "eth_rxd0", - "eth_rxd1", - "eth_rxd2", - "eth_rxd3", - "eth_rgmii_tx_clk", - "eth_tx_en", - "eth_txd0", - "eth_txd1", - "eth_txd2", - "eth_txd3"; - function = "eth"; - }; - }; - }; - }; - - hiubus: hiubus@c883c000 { - compatible = "simple-bus"; - reg = <0x0 0xc883c000 0x0 0x2000>; - #address-cells = <2>; - #size-cells = <2>; - ranges = <0x0 0x0 0x0 0xc883c000 0x0 0x2000>; - - clkc: clock-controller@0 { - compatible = "amlogic,gxbb-clkc"; - #clock-cells = <1>; - reg = <0x0 0x0 0x0 0x3db>; - }; - }; - - apb: apb@d0000000 { - compatible = "simple-bus"; - reg = <0x0 0xd0000000 0x0 0x200000>; - #address-cells = <2>; - #size-cells = <2>; - ranges = <0x0 0x0 0x0 0xd0000000 0x0 0x200000>; - }; - - ethmac: ethernet@c9410000 { - compatible = "amlogic,meson6-dwmac", "snps,dwmac"; - reg = <0x0 0xc9410000 0x0 0x10000 - 0x0 0xc8834540 0x0 0x4>; - interrupts = <0 8 1>; - interrupt-names = "macirq"; - clocks = <&xtal>; - clock-names = "stmmaceth"; - phy-mode = "rgmii"; - status = "disabled"; + gpio: bank@4b0 { + reg = <0x0 0x004b0 0x0 0x28>, + <0x0 0x004e8 0x0 0x14>, + <0x0 0x00120 0x0 0x14>, + <0x0 0x00430 0x0 0x40>; + reg-names = "mux", "pull", "pull-enable", "gpio"; + gpio-controller; + #gpio-cells = <2>; + }; + + emmc_pins: emmc { + mux { + groups = "emmc_nand_d07", + "emmc_cmd", + "emmc_clk", + "emmc_ds"; + function = "emmc"; + }; + }; + + nor_pins: nor { + mux { + groups = "nor_d", + "nor_q", + "nor_c", + "nor_cs"; + function = "nor"; + }; + }; + + sdcard_pins: sdcard { + mux { + groups = "sdcard_d0", + "sdcard_d1", + "sdcard_d2", + "sdcard_d3", + "sdcard_cmd", + "sdcard_clk"; + function = "sdcard"; + }; + }; + + sdio_pins: sdio { + mux { + groups = "sdio_d0", + "sdio_d1", + "sdio_d2", + "sdio_d3", + "sdio_cmd", + "sdio_clk"; + function = "sdio"; + }; + }; + + sdio_irq_pins: sdio_irq { + mux { + groups = "sdio_irq"; + function = "sdio"; + }; + }; + + uart_a_pins: uart_a { + mux { + groups = "uart_tx_a", + "uart_rx_a"; + function = "uart_a"; + }; + }; + + uart_a_cts_rts_pins: uart_a_cts_rts { + mux { + groups = "uart_cts_a", + "uart_rts_a"; + function = "uart_a"; + }; + }; + + uart_b_pins: uart_b { + mux { + groups = "uart_tx_b", + "uart_rx_b"; + function = "uart_b"; + }; + }; + + uart_b_cts_rts_pins: uart_b_cts_rts { + mux { + groups = "uart_cts_b", + "uart_rts_b"; + function = "uart_b"; + }; + }; + + uart_c_pins: uart_c { + mux { + groups = "uart_tx_c", + "uart_rx_c"; + function = "uart_c"; + }; + }; + + uart_c_cts_rts_pins: uart_c_cts_rts { + mux { + groups = "uart_cts_c", + "uart_rts_c"; + function = "uart_c"; + }; + }; + + i2c_a_pins: i2c_a { + mux { + groups = "i2c_sck_a", + "i2c_sda_a"; + function = "i2c_a"; + }; + }; + + i2c_b_pins: i2c_b { + mux { + groups = "i2c_sck_b", + "i2c_sda_b"; + function = "i2c_b"; + }; + }; + + i2c_c_pins: i2c_c { + mux { + groups = "i2c_sck_c", + "i2c_sda_c"; + function = "i2c_c"; + }; + }; + + eth_rgmii_pins: eth-rgmii { + mux { + groups = "eth_mdio", + "eth_mdc", + "eth_clk_rx_clk", + "eth_rx_dv", + "eth_rxd0", + "eth_rxd1", + "eth_rxd2", + "eth_rxd3", + "eth_rgmii_tx_clk", + "eth_tx_en", + "eth_txd0", + "eth_txd1", + "eth_txd2", + "eth_txd3"; + function = "eth"; + }; + }; + + eth_rmii_pins: eth-rmii { + mux { + groups = "eth_mdio", + "eth_mdc", + "eth_clk_rx_clk", + "eth_rx_dv", + "eth_rxd0", + "eth_rxd1", + "eth_tx_en", + "eth_txd0", + "eth_txd1"; + function = "eth"; + }; + }; + + pwm_a_x_pins: pwm_a_x { + mux { + groups = "pwm_a_x"; + function = "pwm_a_x"; + }; + }; + + pwm_a_y_pins: pwm_a_y { + mux { + groups = "pwm_a_y"; + function = "pwm_a_y"; + }; + }; + + pwm_b_pins: pwm_b { + mux { + groups = "pwm_b"; + function = "pwm_b"; + }; + }; + + pwm_d_pins: pwm_d { + mux { + groups = "pwm_d"; + function = "pwm_d"; + }; + }; + + pwm_e_pins: pwm_e { + mux { + groups = "pwm_e"; + function = "pwm_e"; + }; + }; + + pwm_f_x_pins: pwm_f_x { + mux { + groups = "pwm_f_x"; + function = "pwm_f_x"; + }; + }; + + pwm_f_y_pins: pwm_f_y { + mux { + groups = "pwm_f_y"; + function = "pwm_f_y"; + }; + }; + + hdmi_hpd_pins: hdmi_hpd { + mux { + groups = "hdmi_hpd"; + function = "hdmi_hpd"; + }; + }; + + hdmi_i2c_pins: hdmi_i2c { + mux { + groups = "hdmi_sda", "hdmi_scl"; + function = "hdmi_i2c"; + }; }; }; }; + +&hiubus { + clkc: clock-controller@0 { + compatible = "amlogic,gxbb-clkc"; + #clock-cells = <1>; + reg = <0x0 0x0 0x0 0x3db>; + }; +}; + +&i2c_A { + clocks = <&clkc CLKID_I2C>; +}; + +&i2c_B { + clocks = <&clkc CLKID_I2C>; +}; + +&i2c_C { + clocks = <&clkc CLKID_I2C>; +}; + +&sd_emmc_a { + clocks = <&clkc CLKID_SD_EMMC_A>, + <&xtal>, + <&clkc CLKID_FCLK_DIV2>; + clock-names = "core", "clkin0", "clkin1"; +}; + +&sd_emmc_b { + clocks = <&clkc CLKID_SD_EMMC_B>, + <&xtal>, + <&clkc CLKID_FCLK_DIV2>; + clock-names = "core", "clkin0", "clkin1"; +}; + +&sd_emmc_c { + clocks = <&clkc CLKID_SD_EMMC_C>, + <&xtal>, + <&clkc CLKID_FCLK_DIV2>; + clock-names = "core", "clkin0", "clkin1"; +}; + +&vpu { + compatible = "amlogic,meson-gxbb-vpu", "amlogic,meson-gx-vpu"; +}; |