diff options
Diffstat (limited to 'arch/arm')
39 files changed, 1197 insertions, 40 deletions
diff --git a/arch/arm/cpu/armv7/sunxi/clock_sun4i.c b/arch/arm/cpu/armv7/sunxi/clock_sun4i.c index c3e04af..7c8eff9 100644 --- a/arch/arm/cpu/armv7/sunxi/clock_sun4i.c +++ b/arch/arm/cpu/armv7/sunxi/clock_sun4i.c @@ -198,6 +198,15 @@ void clock_set_pll3(unsigned int clk) CCM_PLL3_CTRL_M(clk / 3000000), &ccm->pll3_cfg); } +unsigned int clock_get_pll3(void) +{ + struct sunxi_ccm_reg *const ccm = + (struct sunxi_ccm_reg *)SUNXI_CCM_BASE; + uint32_t rval = readl(&ccm->pll3_cfg); + int m = ((rval & CCM_PLL3_CTRL_M_MASK) >> CCM_PLL3_CTRL_M_SHIFT); + return 3000000 * m; +} + unsigned int clock_get_pll5p(void) { struct sunxi_ccm_reg *const ccm = diff --git a/arch/arm/cpu/armv7/sunxi/clock_sun6i.c b/arch/arm/cpu/armv7/sunxi/clock_sun6i.c index 3bfa122..3ab3b31 100644 --- a/arch/arm/cpu/armv7/sunxi/clock_sun6i.c +++ b/arch/arm/cpu/armv7/sunxi/clock_sun6i.c @@ -170,6 +170,47 @@ void clock_set_pll5(unsigned int clk, bool sigma_delta_enable) udelay(5500); } +#ifdef CONFIG_MACH_SUN6I +void clock_set_mipi_pll(unsigned int clk) +{ + struct sunxi_ccm_reg * const ccm = + (struct sunxi_ccm_reg *)SUNXI_CCM_BASE; + unsigned int k, m, n, value, diff; + unsigned best_k = 0, best_m = 0, best_n = 0, best_diff = 0xffffffff; + unsigned int src = clock_get_pll3(); + + /* All calculations are in KHz to avoid overflows */ + clk /= 1000; + src /= 1000; + + /* Pick the closest lower clock */ + for (k = 1; k <= 4; k++) { + for (m = 1; m <= 16; m++) { + for (n = 1; n <= 16; n++) { + value = src * n * k / m; + if (value > clk) + continue; + + diff = clk - value; + if (diff < best_diff) { + best_diff = diff; + best_k = k; + best_m = m; + best_n = n; + } + if (diff == 0) + goto done; + } + } + } + +done: + writel(CCM_MIPI_PLL_CTRL_EN | CCM_MIPI_PLL_CTRL_LDO_EN | + CCM_MIPI_PLL_CTRL_N(best_n) | CCM_MIPI_PLL_CTRL_K(best_k) | + CCM_MIPI_PLL_CTRL_M(best_m), &ccm->mipi_pll_cfg); +} +#endif + #ifdef CONFIG_MACH_SUN8I_A33 void clock_set_pll11(unsigned int clk, bool sigma_delta_enable) { @@ -188,6 +229,18 @@ void clock_set_pll11(unsigned int clk, bool sigma_delta_enable) } #endif +unsigned int clock_get_pll3(void) +{ + struct sunxi_ccm_reg *const ccm = + (struct sunxi_ccm_reg *)SUNXI_CCM_BASE; + uint32_t rval = readl(&ccm->pll3_cfg); + int n = ((rval & CCM_PLL3_CTRL_N_MASK) >> CCM_PLL3_CTRL_N_SHIFT) + 1; + int m = ((rval & CCM_PLL3_CTRL_M_MASK) >> CCM_PLL3_CTRL_M_SHIFT) + 1; + + /* Multiply by 1000 after dividing by m to avoid integer overflows */ + return (24000 * n / m) * 1000; +} + unsigned int clock_get_pll6(void) { struct sunxi_ccm_reg *const ccm = @@ -198,6 +251,20 @@ unsigned int clock_get_pll6(void) return 24000000 * n * k / 2; } +unsigned int clock_get_mipi_pll(void) +{ + struct sunxi_ccm_reg *const ccm = + (struct sunxi_ccm_reg *)SUNXI_CCM_BASE; + uint32_t rval = readl(&ccm->mipi_pll_cfg); + unsigned int n = ((rval & CCM_MIPI_PLL_CTRL_N_MASK) >> CCM_MIPI_PLL_CTRL_N_SHIFT) + 1; + unsigned int k = ((rval & CCM_MIPI_PLL_CTRL_K_MASK) >> CCM_MIPI_PLL_CTRL_K_SHIFT) + 1; + unsigned int m = ((rval & CCM_MIPI_PLL_CTRL_M_MASK) >> CCM_MIPI_PLL_CTRL_M_SHIFT) + 1; + unsigned int src = clock_get_pll3(); + + /* Multiply by 1000 after dividing by m to avoid integer overflows */ + return ((src / 1000) * n * k / m) * 1000; +} + void clock_set_de_mod_clock(u32 *clk_cfg, unsigned int hz) { int pll = clock_get_pll6() * 2; diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index ff86891..d9a2f5f 100644 --- a/arch/arm/dts/Makefile +++ b/arch/arm/dts/Makefile @@ -77,6 +77,7 @@ dtb-$(CONFIG_MACH_SUN4I) += \ sun4i-a10-inet-3f.dtb \ sun4i-a10-inet-3w.dtb \ sun4i-a10-inet97fv2.dtb \ + sun4i-a10-itead-iteaduino-plus.dtb \ sun4i-a10-jesurun-q5.dtb \ sun4i-a10-marsboard.dtb \ sun4i-a10-mini-xplus.dtb \ @@ -85,6 +86,7 @@ dtb-$(CONFIG_MACH_SUN4I) += \ sun4i-a10-olinuxino-lime.dtb \ sun4i-a10-pcduino.dtb dtb-$(CONFIG_MACH_SUN5I) += \ + sun5i-a10s-auxtek-t003.dtb \ sun5i-a10s-auxtek-t004.dtb \ sun5i-a10s-mk802.dtb \ sun5i-a10s-olinuxino-micro.dtb \ diff --git a/arch/arm/dts/axp152.dtsi b/arch/arm/dts/axp152.dtsi new file mode 100644 index 0000000..f90ad6c --- /dev/null +++ b/arch/arm/dts/axp152.dtsi @@ -0,0 +1,49 @@ +/* + * Copyright 2015 Chen-Yu Tsai + * + * Chen-Yu Tsai <wens@csie.org> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +&axp152 { + compatible = "x-powers,axp152"; + interrupt-controller; + #interrupt-cells = <1>; +}; diff --git a/arch/arm/dts/axp209.dtsi b/arch/arm/dts/axp209.dtsi index c20cf53..24c935c 100644 --- a/arch/arm/dts/axp209.dtsi +++ b/arch/arm/dts/axp209.dtsi @@ -18,11 +18,6 @@ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * - * You should have received a copy of the GNU General Public - * License along with this file; if not, write to the Free - * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, - * MA 02110-1301 USA - * * Or, alternatively, * * b) Permission is hereby granted, free of charge, to any person diff --git a/arch/arm/dts/sun4i-a10-ba10-tvbox.dts b/arch/arm/dts/sun4i-a10-ba10-tvbox.dts index 93d4356..f3cb297 100644 --- a/arch/arm/dts/sun4i-a10-ba10-tvbox.dts +++ b/arch/arm/dts/sun4i-a10-ba10-tvbox.dts @@ -125,12 +125,21 @@ status = "okay"; }; +&otg_sram { + status = "okay"; +}; + &pio { usb2_vbus_pin_a: usb2_vbus_pin@0 { allwinner,pins = "PH12"; }; }; +®_usb0_vbus { + regulator-boot-on; + status = "okay"; +}; + ®_usb1_vbus { status = "okay"; }; @@ -146,7 +155,13 @@ status = "okay"; }; +&usb_otg { + dr_mode = "host"; + status = "okay"; +}; + &usbphy { + usb0_vbus-supply = <®_usb0_vbus>; usb1_vbus-supply = <®_usb1_vbus>; usb2_vbus-supply = <®_usb2_vbus>; status = "okay"; diff --git a/arch/arm/dts/sun4i-a10-chuwi-v7-cw0825.dts b/arch/arm/dts/sun4i-a10-chuwi-v7-cw0825.dts index 5878a0b..1430568 100644 --- a/arch/arm/dts/sun4i-a10-chuwi-v7-cw0825.dts +++ b/arch/arm/dts/sun4i-a10-chuwi-v7-cw0825.dts @@ -114,6 +114,30 @@ status = "okay"; }; +&otg_sram { + status = "okay"; +}; + +&pio { + usb0_id_detect_pin: usb0_id_detect_pin@0 { + allwinner,pins = "PH4"; + allwinner,function = "gpio_in"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_PULL_UP>; + }; + + usb0_vbus_detect_pin: usb0_vbus_detect_pin@0 { + allwinner,pins = "PH5"; + allwinner,function = "gpio_in"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_PULL_DOWN>; + }; +}; + +®_usb0_vbus { + status = "okay"; +}; + ®_usb2_vbus { status = "okay"; }; @@ -124,7 +148,17 @@ status = "okay"; }; +&usb_otg { + dr_mode = "otg"; + status = "okay"; +}; + &usbphy { + pinctrl-names = "default"; + pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>; + usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */ + usb0_vbus_det-gpio = <&pio 7 5 GPIO_ACTIVE_HIGH>; /* PH5 */ + usb0_vbus-supply = <®_usb0_vbus>; usb2_vbus-supply = <®_usb2_vbus>; status = "okay"; }; diff --git a/arch/arm/dts/sun4i-a10-cubieboard.dts b/arch/arm/dts/sun4i-a10-cubieboard.dts index 9afb4e0..046a84d 100644 --- a/arch/arm/dts/sun4i-a10-cubieboard.dts +++ b/arch/arm/dts/sun4i-a10-cubieboard.dts @@ -155,6 +155,10 @@ status = "okay"; }; +&otg_sram { + status = "okay"; +}; + &pio { led_pins_cubieboard: led_pins@0 { allwinner,pins = "PH20", "PH21"; @@ -162,6 +166,13 @@ allwinner,drive = <SUN4I_PINCTRL_20_MA>; allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; }; + + usb0_id_detect_pin: usb0_id_detect_pin@0 { + allwinner,pins = "PH4"; + allwinner,function = "gpio_in"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_PULL_UP>; + }; }; ®_ahci_5v { @@ -216,7 +227,15 @@ status = "okay"; }; +&usb_otg { + dr_mode = "otg"; + status = "okay"; +}; + &usbphy { + pinctrl-names = "default"; + pinctrl-0 = <&usb0_id_detect_pin>; + usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */ usb1_vbus-supply = <®_usb1_vbus>; usb2_vbus-supply = <®_usb2_vbus>; status = "okay"; diff --git a/arch/arm/dts/sun4i-a10-itead-iteaduino-plus.dts b/arch/arm/dts/sun4i-a10-itead-iteaduino-plus.dts new file mode 100644 index 0000000..985e155 --- /dev/null +++ b/arch/arm/dts/sun4i-a10-itead-iteaduino-plus.dts @@ -0,0 +1,202 @@ +/* + * Copyright 2015 Josef Gajdusek <atx@atx.name> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; +#include "sun4i-a10.dtsi" +#include "sunxi-common-regulators.dtsi" + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/pinctrl/sun4i-a10.h> + +/ { + model = "Iteaduino Plus A10"; + compatible = "itead,iteaduino-plus-a10", "allwinner,sun4i-a10"; + + aliases { + serial0 = &uart0; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; +}; + +&ahci { + target-supply = <®_ahci_5v>; + status = "okay"; +}; + +&cpu0 { + cpu-supply = <®_dcdc2>; +}; + +&ehci0 { + status = "okay"; +}; + +&ehci1 { + status = "okay"; +}; + +&emac { + pinctrl-names = "default"; + pinctrl-0 = <&emac_pins_a>; + phy = <&phy1>; + status = "okay"; +}; + +&emac_sram { + status = "okay"; +}; + +&i2c0 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins_a>; + status = "okay"; + + axp209: pmic@34 { + reg = <0x34>; + interrupts = <0>; + }; +}; + +&i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins_a>; + status = "okay"; +}; + +&i2c2 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_pins_a>; + status = "okay"; +}; + +&ir0 { + pinctrl-names = "default"; + pinctrl-0 = <&ir0_rx_pins_a>; + status = "okay"; +}; + +&mdio { + status = "okay"; + + phy1: ethernet-phy@1 { + reg = <1>; + }; +}; + +&mmc0 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>; + vmmc-supply = <®_vcc3v3>; + bus-width = <4>; + cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */ + cd-inverted; + status = "okay"; +}; + +&ohci0 { + status = "okay"; +}; + +&ohci1 { + status = "okay"; +}; + +®_ahci_5v { + status = "okay"; +}; + +#include "axp209.dtsi" + +®_dcdc2 { + regulator-always-on; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1450000>; + regulator-name = "vdd-cpu"; +}; + +®_dcdc3 { + regulator-always-on; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1400000>; + regulator-name = "vdd-int-dll"; +}; + +®_ldo1 { + regulator-name = "vdd-rtc"; +}; + +®_ldo2 { + regulator-always-on; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-name = "avcc"; +}; + +®_usb1_vbus { + status = "okay"; +}; + +®_usb2_vbus { + status = "okay"; +}; + +&spi0 { + pinctrl-names = "default"; + pinctrl-0 = <&spi0_pins_a>, + <&spi0_cs0_pins_a>; + status = "okay"; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pins_a>; + status = "okay"; +}; + +&usbphy { + usb1_vbus-supply = <®_usb1_vbus>; + usb2_vbus-supply = <®_usb2_vbus>; + status = "okay"; +}; diff --git a/arch/arm/dts/sun4i-a10-mini-xplus.dts b/arch/arm/dts/sun4i-a10-mini-xplus.dts index ebe2a04..a7dd86d 100644 --- a/arch/arm/dts/sun4i-a10-mini-xplus.dts +++ b/arch/arm/dts/sun4i-a10-mini-xplus.dts @@ -114,6 +114,15 @@ status = "okay"; }; +&otg_sram { + status = "okay"; +}; + +®_usb0_vbus { + regulator-boot-on; + status = "okay"; +}; + ®_usb1_vbus { status = "okay"; }; @@ -128,7 +137,13 @@ status = "okay"; }; +&usb_otg { + dr_mode = "host"; + status = "okay"; +}; + &usbphy { + usb0_vbus-supply = <®_usb0_vbus>; usb1_vbus-supply = <®_usb1_vbus>; usb2_vbus-supply = <®_usb2_vbus>; status = "okay"; diff --git a/arch/arm/dts/sun4i-a10-olinuxino-lime.dts b/arch/arm/dts/sun4i-a10-olinuxino-lime.dts index b64aa4e..28e32ad 100644 --- a/arch/arm/dts/sun4i-a10-olinuxino-lime.dts +++ b/arch/arm/dts/sun4i-a10-olinuxino-lime.dts @@ -150,6 +150,10 @@ status = "okay"; }; +&otg_sram { + status = "okay"; +}; + &pio { ahci_pwr_pin_olinuxinolime: ahci_pwr_pin@1 { allwinner,pins = "PC3"; @@ -164,6 +168,20 @@ allwinner,drive = <SUN4I_PINCTRL_20_MA>; allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; }; + + usb0_id_detect_pin: usb0_id_detect_pin@0 { + allwinner,pins = "PH4"; + allwinner,function = "gpio_in"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_PULL_UP>; + }; + + usb0_vbus_detect_pin: usb0_vbus_detect_pin@0 { + allwinner,pins = "PH5"; + allwinner,function = "gpio_in"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_PULL_DOWN>; + }; }; ®_ahci_5v { @@ -172,6 +190,10 @@ status = "okay"; }; +®_usb0_vbus { + status = "okay"; +}; + ®_usb1_vbus { status = "okay"; }; @@ -186,7 +208,17 @@ status = "okay"; }; +&usb_otg { + dr_mode = "otg"; + status = "okay"; +}; + &usbphy { + pinctrl-names = "default"; + pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>; + usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */ + usb0_vbus_det-gpio = <&pio 7 5 GPIO_ACTIVE_HIGH>; /* PH5 */ + usb0_vbus-supply = <®_usb0_vbus>; usb1_vbus-supply = <®_usb1_vbus>; usb2_vbus-supply = <®_usb2_vbus>; status = "okay"; diff --git a/arch/arm/dts/sun4i-a10.dtsi b/arch/arm/dts/sun4i-a10.dtsi index 61c03d1..463bacd 100644 --- a/arch/arm/dts/sun4i-a10.dtsi +++ b/arch/arm/dts/sun4i-a10.dtsi @@ -611,6 +611,19 @@ #size-cells = <0>; }; + usb_otg: usb@01c13000 { + compatible = "allwinner,sun4i-a10-musb"; + reg = <0x01c13000 0x0400>; + clocks = <&ahb_gates 0>; + interrupts = <38>; + interrupt-names = "mc"; + phys = <&usbphy 0>; + phy-names = "usb"; + extcon = <&usbphy 0>; + allwinner,sram = <&otg_sram 1>; + status = "disabled"; + }; + usbphy: phy@01c13400 { #phy-cells = <1>; compatible = "allwinner,sun4i-a10-usb-phy"; @@ -713,8 +726,7 @@ clocks = <&apb0_gates 5>; gpio-controller; interrupt-controller; - #interrupt-cells = <2>; - #size-cells = <0>; + #interrupt-cells = <3>; #gpio-cells = <3>; pwm0_pins_a: pwm0@0 { diff --git a/arch/arm/dts/sun5i-a10s-auxtek-t003.dts b/arch/arm/dts/sun5i-a10s-auxtek-t003.dts new file mode 100644 index 0000000..d4ad021 --- /dev/null +++ b/arch/arm/dts/sun5i-a10s-auxtek-t003.dts @@ -0,0 +1,159 @@ +/* + * Copyright 2015 Hans de Goede <hdegoede@redhat.com> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; +#include "sun5i-a10s.dtsi" +#include "sunxi-common-regulators.dtsi" +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/pinctrl/sun4i-a10.h> + +/ { + model = "Auxtek t003 A10s hdmi tv-stick"; + compatible = "allwinner,auxtek-t003", "allwinner,sun5i-a10s"; + + aliases { + serial0 = &uart0; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&led_pins_t003>; + + red { + label = "t003-tv-dongle:red:usr"; + gpios = <&pio 1 2 GPIO_ACTIVE_HIGH>; /* PB2 */ + default-state = "on"; + }; + }; +}; + +&ehci0 { + status = "okay"; +}; + +&i2c0 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins_a>; + status = "okay"; + + axp152: pmic@30 { + compatible = "x-powers,axp152"; + reg = <0x30>; + interrupts = <0>; + interrupt-controller; + #interrupt-cells = <1>; + }; +}; + +&mmc0 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_t003>; + vmmc-supply = <®_vcc3v3>; + bus-width = <4>; + cd-gpios = <&pio 6 1 GPIO_ACTIVE_HIGH>; /* PG1 */ + cd-inverted; + status = "okay"; +}; + +&ohci0 { + status = "okay"; +}; + +&otg_sram { + status = "okay"; +}; + +&pio { + mmc0_cd_pin_t003: mmc0_cd_pin@0 { + allwinner,pins = "PG1"; + allwinner,function = "gpio_in"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_PULL_UP>; + }; + + led_pins_t003: led_pins@0 { + allwinner,pins = "PB2"; + allwinner,function = "gpio_out"; + allwinner,drive = <SUN4I_PINCTRL_20_MA>; + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; + }; +}; + +®_usb0_vbus { + gpio = <&pio 6 13 GPIO_ACTIVE_HIGH>; /* PG13 */ + status = "okay"; +}; + +®_usb1_vbus { + gpio = <&pio 1 10 GPIO_ACTIVE_HIGH>; /* PB10 */ + status = "okay"; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pins_a>; + status = "okay"; +}; + +&usb0_vbus_pin_a { + allwinner,pins = "PG13"; +}; + +&usb1_vbus_pin_a { + allwinner,pins = "PB10"; +}; + +&usb_otg { + dr_mode = "host"; + status = "okay"; +}; + +&usbphy { + usb0_vbus-supply = <®_usb0_vbus>; + usb1_vbus-supply = <®_usb1_vbus>; + status = "okay"; +}; diff --git a/arch/arm/dts/sun5i-a10s-olinuxino-micro.dts b/arch/arm/dts/sun5i-a10s-olinuxino-micro.dts index a7e19e4..5a422c1 100644 --- a/arch/arm/dts/sun5i-a10s-olinuxino-micro.dts +++ b/arch/arm/dts/sun5i-a10s-olinuxino-micro.dts @@ -96,8 +96,15 @@ pinctrl-names = "default"; pinctrl-0 = <&i2c0_pins_a>; status = "okay"; + + axp152: pmic@30 { + reg = <0x30>; + interrupts = <0>; + }; }; +#include "axp152.dtsi" + &i2c1 { pinctrl-names = "default"; pinctrl-0 = <&i2c1_pins_a>; @@ -189,6 +196,10 @@ status = "okay"; }; +&otg_sram { + status = "okay"; +}; + &pio { mmc0_cd_pin_olinuxino_micro: mmc0_cd_pin@0 { allwinner,pins = "PG1"; @@ -217,6 +228,18 @@ allwinner,drive = <SUN4I_PINCTRL_10_MA>; allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; }; + + usb0_id_detect_pin: usb0_id_detect_pin@0 { + allwinner,pins = "PG12"; + allwinner,function = "gpio_in"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_PULL_UP>; + }; +}; + +®_usb0_vbus { + gpio = <&pio 6 11 GPIO_ACTIVE_HIGH>; /* PG11 */ + status = "okay"; }; ®_usb1_vbus { @@ -243,8 +266,20 @@ status = "okay"; }; +&usb_otg { + dr_mode = "otg"; + status = "okay"; +}; + +&usb0_vbus_pin_a { + allwinner,pins = "PG11"; +}; + &usbphy { + pinctrl-names = "default"; + pinctrl-0 = <&usb0_id_detect_pin>; + usb0_id_det-gpio = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */ + usb0_vbus-supply = <®_usb0_vbus>; usb1_vbus-supply = <®_usb1_vbus>; status = "okay"; }; - diff --git a/arch/arm/dts/sun5i-a13-hsg-h702.dts b/arch/arm/dts/sun5i-a13-hsg-h702.dts index 990f9d6..3724b98 100644 --- a/arch/arm/dts/sun5i-a13-hsg-h702.dts +++ b/arch/arm/dts/sun5i-a13-hsg-h702.dts @@ -45,6 +45,7 @@ #include "sunxi-common-regulators.dtsi" #include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> #include <dt-bindings/pinctrl/sun4i-a10.h> / { @@ -96,6 +97,25 @@ status = "okay"; }; +&lradc { + vref-supply = <®_ldo2>; + status = "okay"; + + button@200 { + label = "Volume Up"; + linux,code = <KEY_VOLUMEUP>; + channel = <0>; + voltage = <200000>; + }; + + button@400 { + label = "Volume Down"; + linux,code = <KEY_VOLUMEDOWN>; + channel = <0>; + voltage = <400000>; + }; +}; + &mmc0 { pinctrl-names = "default"; pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_h702>; @@ -110,6 +130,10 @@ status = "okay"; }; +&otg_sram { + status = "okay"; +}; + &pio { mmc0_cd_pin_h702: mmc0_cd_pin@0 { allwinner,pins = "PG0"; @@ -117,6 +141,20 @@ allwinner,drive = <SUN4I_PINCTRL_10_MA>; allwinner,pull = <SUN4I_PINCTRL_PULL_UP>; }; + + usb0_id_detect_pin: usb0_id_detect_pin@0 { + allwinner,pins = "PG2"; + allwinner,function = "gpio_in"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_PULL_UP>; + }; + + usb0_vbus_detect_pin: usb0_vbus_detect_pin@0 { + allwinner,pins = "PG1"; + allwinner,function = "gpio_in"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; + }; }; #include "axp209.dtsi" @@ -152,13 +190,33 @@ regulator-name = "vcc-wifi"; }; +®_usb0_vbus { + pinctrl-0 = <&usb0_vbus_pin_a>; + gpio = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */ + status = "okay"; +}; + &uart1 { pinctrl-names = "default"; pinctrl-0 = <&uart1_pins_b>; status = "okay"; }; +&usb_otg { + dr_mode = "otg"; + status = "okay"; +}; + +&usb0_vbus_pin_a { + allwinner,pins = "PG12"; +}; + &usbphy { + pinctrl-names = "default"; + pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>; + usb0_id_det-gpios = <&pio 6 2 GPIO_ACTIVE_HIGH>; /* PG2 */ + usb0_vbus_det-gpios = <&pio 6 1 GPIO_ACTIVE_HIGH>; /* PG1 */ + usb0_vbus-supply = <®_usb0_vbus>; usb1_vbus-supply = <®_ldo3>; status = "okay"; }; diff --git a/arch/arm/dts/sun5i-a13-olinuxino.dts b/arch/arm/dts/sun5i-a13-olinuxino.dts index 4232400..b3c234c 100644 --- a/arch/arm/dts/sun5i-a13-olinuxino.dts +++ b/arch/arm/dts/sun5i-a13-olinuxino.dts @@ -159,6 +159,10 @@ status = "okay"; }; +&otg_sram { + status = "okay"; +}; + &pio { mmc0_cd_pin_olinuxino: mmc0_cd_pin@0 { allwinner,pins = "PG0"; @@ -174,6 +178,20 @@ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; }; + usb0_id_detect_pin: usb0_id_detect_pin@0 { + allwinner,pins = "PG2"; + allwinner,function = "gpio_in"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_PULL_UP>; + }; + + usb0_vbus_detect_pin: usb0_vbus_detect_pin@0 { + allwinner,pins = "PG1"; + allwinner,function = "gpio_in"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_PULL_DOWN>; + }; + usb1_vbus_pin_olinuxino: usb1_vbus_pin@0 { allwinner,pins = "PG11"; allwinner,function = "gpio_out"; @@ -182,6 +200,11 @@ }; }; +®_usb0_vbus { + status = "okay"; + gpio = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */ +}; + ®_usb1_vbus { pinctrl-0 = <&usb1_vbus_pin_olinuxino>; gpio = <&pio 6 11 GPIO_ACTIVE_HIGH>; @@ -194,7 +217,21 @@ status = "okay"; }; +&usb_otg { + dr_mode = "otg"; + status = "okay"; +}; + +&usb0_vbus_pin_a { + allwinner,pins = "PG12"; +}; + &usbphy { + pinctrl-names = "default"; + pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>; + usb0_id_det-gpio = <&pio 6 2 GPIO_ACTIVE_HIGH>; /* PG2 */ + usb0_vbus_det-gpio = <&pio 6 1 GPIO_ACTIVE_HIGH>; /* PG1 */ + usb0_vbus-supply = <®_usb0_vbus>; usb1_vbus-supply = <®_usb1_vbus>; status = "okay"; }; diff --git a/arch/arm/dts/sun5i-a13-utoo-p66.dts b/arch/arm/dts/sun5i-a13-utoo-p66.dts index 514f159..eb793d5 100644 --- a/arch/arm/dts/sun5i-a13-utoo-p66.dts +++ b/arch/arm/dts/sun5i-a13-utoo-p66.dts @@ -93,7 +93,7 @@ compatible = "chipone,icn8318"; reg = <0x40>; interrupt-parent = <&pio>; - interrupts = <9 IRQ_TYPE_EDGE_FALLING>; /* EINT9 (PG9) */ + interrupts = <6 9 IRQ_TYPE_EDGE_FALLING>; /* EINT9 (PG9) */ pinctrl-names = "default"; pinctrl-0 = <&ts_wake_pin_p66>; wake-gpios = <&pio 1 3 GPIO_ACTIVE_HIGH>; /* PB3 */ @@ -153,6 +153,10 @@ }; }; +&otg_sram { + status = "okay"; +}; + &pio { mmc0_cd_pin_p66: mmc0_cd_pin@0 { allwinner,pins = "PG0"; @@ -161,6 +165,20 @@ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>; }; + usb0_vbus_detect_pin: usb0_vbus_detect_pin@0 { + allwinner,pins = "PG1"; + allwinner,function = "gpio_in"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_PULL_DOWN>; + }; + + usb0_id_detect_pin: usb0_id_detect_pin@0 { + allwinner,pins = "PG2"; + allwinner,function = "gpio_in"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_PULL_UP>; + }; + i2c_lcd_pins: i2c_lcd_pin@0 { allwinner,pins = "PG10", "PG12"; allwinner,function = "gpio_out"; @@ -219,7 +237,16 @@ status = "okay"; }; +&usb_otg { + dr_mode = "otg"; + status = "okay"; +}; + &usbphy { + pinctrl-names = "default"; + pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>; + usb0_id_det-gpio = <&pio 6 2 GPIO_ACTIVE_HIGH>; /* PG2 */ + usb0_vbus_det-gpio = <&pio 6 1 GPIO_ACTIVE_HIGH>; /* PG1 */ usb0_vbus-supply = <®_usb0_vbus>; usb1_vbus-supply = <®_ldo3>; status = "okay"; diff --git a/arch/arm/dts/sun5i.dtsi b/arch/arm/dts/sun5i.dtsi index 54b0978..759117d 100644 --- a/arch/arm/dts/sun5i.dtsi +++ b/arch/arm/dts/sun5i.dtsi @@ -416,6 +416,19 @@ #size-cells = <0>; }; + usb_otg: usb@01c13000 { + compatible = "allwinner,sun4i-a10-musb"; + reg = <0x01c13000 0x0400>; + clocks = <&ahb_gates 0>; + interrupts = <38>; + interrupt-names = "mc"; + phys = <&usbphy 0>; + phy-names = "usb"; + extcon = <&usbphy 0>; + allwinner,sram = <&otg_sram 1>; + status = "disabled"; + }; + usbphy: phy@01c13400 { #phy-cells = <1>; compatible = "allwinner,sun5i-a13-usb-phy"; @@ -475,8 +488,7 @@ clocks = <&apb0_gates 5>; gpio-controller; interrupt-controller; - #interrupt-cells = <2>; - #size-cells = <0>; + #interrupt-cells = <3>; #gpio-cells = <3>; i2c0_pins_a: i2c0@0 { diff --git a/arch/arm/dts/sun6i-a31-colombus.dts b/arch/arm/dts/sun6i-a31-colombus.dts index 0cf9926..0d0b6f2 100644 --- a/arch/arm/dts/sun6i-a31-colombus.dts +++ b/arch/arm/dts/sun6i-a31-colombus.dts @@ -66,6 +66,18 @@ status = "okay"; }; +&gmac { + pinctrl-names = "default"; + pinctrl-0 = <&gmac_pins_rgmii_a>; + phy = <&phy1>; + phy-mode = "rgmii"; + status = "okay"; + + phy1: ethernet-phy@1 { + reg = <1>; + }; +}; + &i2c0 { pinctrl-names = "default"; pinctrl-0 = <&i2c0_pins_a>; diff --git a/arch/arm/dts/sun6i-a31-m9.dts b/arch/arm/dts/sun6i-a31-m9.dts index a5660d6..6e0e568 100644 --- a/arch/arm/dts/sun6i-a31-m9.dts +++ b/arch/arm/dts/sun6i-a31-m9.dts @@ -48,7 +48,7 @@ #include <dt-bindings/pinctrl/sun4i-a10.h> / { - model = "Mele M9 / A1000G Quad top set box"; + model = "Mele M9 top set box"; compatible = "mele,m9", "allwinner,sun6i-a31"; aliases { diff --git a/arch/arm/dts/sun6i-a31-mele-a1000g-quad.dts b/arch/arm/dts/sun6i-a31-mele-a1000g-quad.dts index 4404f37..4dd70cc 100644 --- a/arch/arm/dts/sun6i-a31-mele-a1000g-quad.dts +++ b/arch/arm/dts/sun6i-a31-mele-a1000g-quad.dts @@ -143,6 +143,11 @@ status = "okay"; }; +&usb_otg { + dr_mode = "host"; + status = "okay"; +}; + &usbphy { usb1_vbus-supply = <®_usb1_vbus>; status = "okay"; diff --git a/arch/arm/dts/sun6i-a31.dtsi b/arch/arm/dts/sun6i-a31.dtsi index 008047a..39953e7 100644 --- a/arch/arm/dts/sun6i-a31.dtsi +++ b/arch/arm/dts/sun6i-a31.dtsi @@ -512,6 +512,19 @@ #size-cells = <0>; }; + usb_otg: usb@01c19000 { + compatible = "allwinner,sun6i-a31-musb"; + reg = <0x01c19000 0x0400>; + clocks = <&ahb1_gates 24>; + resets = <&ahb1_rst 24>; + interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "mc"; + phys = <&usbphy 0>; + phy-names = "usb"; + extcon = <&usbphy 0>; + status = "disabled"; + }; + usbphy: phy@01c19400 { compatible = "allwinner,sun6i-a31-usb-phy"; reg = <0x01c19400 0x10>, @@ -599,8 +612,7 @@ clocks = <&apb1_gates 5>; gpio-controller; interrupt-controller; - #interrupt-cells = <2>; - #size-cells = <0>; + #interrupt-cells = <3>; #gpio-cells = <3>; uart0_pins_a: uart0@0 { diff --git a/arch/arm/dts/sun6i-a31s-cs908.dts b/arch/arm/dts/sun6i-a31s-cs908.dts index 1e2411a..5e8f8c4 100644 --- a/arch/arm/dts/sun6i-a31s-cs908.dts +++ b/arch/arm/dts/sun6i-a31s-cs908.dts @@ -93,6 +93,11 @@ status = "okay"; }; +&usb_otg { + dr_mode = "host"; + status = "okay"; +}; + &usbphy { status = "okay"; }; diff --git a/arch/arm/dts/sun7i-a20-cubietruck.dts b/arch/arm/dts/sun7i-a20-cubietruck.dts index 4611e2f..e6b0192 100644 --- a/arch/arm/dts/sun7i-a20-cubietruck.dts +++ b/arch/arm/dts/sun7i-a20-cubietruck.dts @@ -88,15 +88,11 @@ }; }; - reg_vmmc3: vmmc3 { - compatible = "regulator-fixed"; + mmc3_pwrseq: mmc3_pwrseq { + compatible = "mmc-pwrseq-simple"; pinctrl-names = "default"; - pinctrl-0 = <&vmmc3_pin_cubietruck>; - regulator-name = "vmmc3"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - enable-active-high; - gpio = <&pio 7 9 GPIO_ACTIVE_HIGH>; + pinctrl-0 = <&mmc3_pwrseq_pin_cubietruck>; + reset-gpios = <&pio 7 9 GPIO_ACTIVE_LOW>; /* PH9 WIFI_EN */ }; }; @@ -172,7 +168,8 @@ &mmc3 { pinctrl-names = "default"; pinctrl-0 = <&mmc3_pins_a>; - vmmc-supply = <®_vmmc3>; + vmmc-supply = <®_vcc3v3>; + mmc-pwrseq = <&mmc3_pwrseq>; bus-width = <4>; non-removable; status = "okay"; @@ -181,7 +178,7 @@ reg = <1>; compatible = "brcm,bcm4329-fmac"; interrupt-parent = <&pio>; - interrupts = <10 IRQ_TYPE_LEVEL_LOW>; /* PH10 / EINT10 */ + interrupts = <7 10 IRQ_TYPE_LEVEL_LOW>; /* PH10 / EINT10 */ interrupt-names = "host-wake"; }; }; @@ -199,23 +196,27 @@ status = "okay"; }; +&otg_sram { + status = "okay"; +}; + &pio { - vmmc3_pin_cubietruck: vmmc3_pin@0 { - allwinner,pins = "PH9"; + ahci_pwr_pin_cubietruck: ahci_pwr_pin@1 { + allwinner,pins = "PH12"; allwinner,function = "gpio_out"; allwinner,drive = <SUN4I_PINCTRL_10_MA>; allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; }; - ahci_pwr_pin_cubietruck: ahci_pwr_pin@1 { - allwinner,pins = "PH12"; + led_pins_cubietruck: led_pins@0 { + allwinner,pins = "PH7", "PH11", "PH20", "PH21"; allwinner,function = "gpio_out"; allwinner,drive = <SUN4I_PINCTRL_10_MA>; allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; }; - led_pins_cubietruck: led_pins@0 { - allwinner,pins = "PH7", "PH11", "PH20", "PH21"; + mmc3_pwrseq_pin_cubietruck: mmc3_pwrseq_pin@0 { + allwinner,pins = "PH9"; allwinner,function = "gpio_out"; allwinner,drive = <SUN4I_PINCTRL_10_MA>; allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; @@ -227,6 +228,20 @@ allwinner,drive = <SUN4I_PINCTRL_10_MA>; allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; }; + + usb0_id_detect_pin: usb0_id_detect_pin@0 { + allwinner,pins = "PH19"; + allwinner,function = "gpio_in"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; + }; + + usb0_vbus_detect_pin: usb0_vbus_detect_pin@0 { + allwinner,pins = "PH22"; + allwinner,function = "gpio_in"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; + }; }; &pwm { @@ -288,7 +303,16 @@ status = "okay"; }; +&usb_otg { + dr_mode = "otg"; + status = "okay"; +}; + &usbphy { + pinctrl-names = "default"; + pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>; + usb0_id_det-gpios = <&pio 7 19 GPIO_ACTIVE_HIGH>; /* PH19 */ + usb0_vbus_det-gpios = <&pio 7 22 GPIO_ACTIVE_HIGH>; /* PH22 */ usb0_vbus-supply = <®_usb0_vbus>; usb1_vbus-supply = <®_usb1_vbus>; usb2_vbus-supply = <®_usb2_vbus>; diff --git a/arch/arm/dts/sun7i-a20-i12-tvbox.dts b/arch/arm/dts/sun7i-a20-i12-tvbox.dts index f32f6f2..1e6bd36 100644 --- a/arch/arm/dts/sun7i-a20-i12-tvbox.dts +++ b/arch/arm/dts/sun7i-a20-i12-tvbox.dts @@ -178,7 +178,7 @@ reg = <1>; compatible = "brcm,bcm4329-fmac"; interrupt-parent = <&pio>; - interrupts = <10 IRQ_TYPE_LEVEL_LOW>; /* PH10 / EINT10 */ + interrupts = <7 10 IRQ_TYPE_LEVEL_LOW>; /* PH10 / EINT10 */ interrupt-names = "host-wake"; }; }; diff --git a/arch/arm/dts/sun7i-a20-olinuxino-lime.dts b/arch/arm/dts/sun7i-a20-olinuxino-lime.dts index 769726d..0423708 100644 --- a/arch/arm/dts/sun7i-a20-olinuxino-lime.dts +++ b/arch/arm/dts/sun7i-a20-olinuxino-lime.dts @@ -135,6 +135,10 @@ status = "okay"; }; +&otg_sram { + status = "okay"; +}; + &pio { ahci_pwr_pin_olinuxinolime: ahci_pwr_pin@1 { allwinner,pins = "PC3"; @@ -149,6 +153,20 @@ allwinner,drive = <SUN4I_PINCTRL_20_MA>; allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; }; + + usb0_id_detect_pin: usb0_id_detect_pin@0 { + allwinner,pins = "PH4"; + allwinner,function = "gpio_in"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_PULL_UP>; + }; + + usb0_vbus_detect_pin: usb0_vbus_detect_pin@0 { + allwinner,pins = "PH5"; + allwinner,function = "gpio_in"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_PULL_DOWN>; + }; }; ®_ahci_5v { @@ -157,6 +175,10 @@ status = "okay"; }; +®_usb0_vbus { + status = "okay"; +}; + ®_usb1_vbus { status = "okay"; }; @@ -171,7 +193,17 @@ status = "okay"; }; +&usb_otg { + dr_mode = "otg"; + status = "okay"; +}; + &usbphy { + pinctrl-names = "default"; + pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>; + usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */ + usb0_vbus_det-gpio = <&pio 7 5 GPIO_ACTIVE_HIGH>; /* PH5 */ + usb0_vbus-supply = <®_usb0_vbus>; usb1_vbus-supply = <®_usb1_vbus>; usb2_vbus-supply = <®_usb2_vbus>; status = "okay"; diff --git a/arch/arm/dts/sun7i-a20-olinuxino-micro.dts b/arch/arm/dts/sun7i-a20-olinuxino-micro.dts index 00f8f25..c5d70ca 100644 --- a/arch/arm/dts/sun7i-a20-olinuxino-micro.dts +++ b/arch/arm/dts/sun7i-a20-olinuxino-micro.dts @@ -215,6 +215,10 @@ status = "okay"; }; +&otg_sram { + status = "okay"; +}; + &pio { mmc3_cd_pin_olinuxinom: mmc3_cd_pin@0 { allwinner,pins = "PH11"; @@ -229,12 +233,30 @@ allwinner,drive = <SUN4I_PINCTRL_20_MA>; allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; }; + + usb0_id_detect_pin: usb0_id_detect_pin@0 { + allwinner,pins = "PH4"; + allwinner,function = "gpio_in"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_PULL_UP>; + }; + + usb0_vbus_detect_pin: usb0_vbus_detect_pin@0 { + allwinner,pins = "PH5"; + allwinner,function = "gpio_in"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_PULL_DOWN>; + }; }; ®_ahci_5v { status = "okay"; }; +®_usb0_vbus { + status = "okay"; +}; + ®_usb1_vbus { status = "okay"; }; @@ -275,7 +297,17 @@ status = "okay"; }; +&usb_otg { + dr_mode = "otg"; + status = "okay"; +}; + &usbphy { + pinctrl-names = "default"; + pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>; + usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */ + usb0_vbus_det-gpio = <&pio 7 5 GPIO_ACTIVE_HIGH>; /* PH5 */ + usb0_vbus-supply = <®_usb0_vbus>; usb1_vbus-supply = <®_usb1_vbus>; usb2_vbus-supply = <®_usb2_vbus>; status = "okay"; diff --git a/arch/arm/dts/sun7i-a20.dtsi b/arch/arm/dts/sun7i-a20.dtsi index 6a63f30..71ab6b8 100644 --- a/arch/arm/dts/sun7i-a20.dtsi +++ b/arch/arm/dts/sun7i-a20.dtsi @@ -699,6 +699,19 @@ #size-cells = <0>; }; + usb_otg: usb@01c13000 { + compatible = "allwinner,sun4i-a10-musb"; + reg = <0x01c13000 0x0400>; + clocks = <&ahb_gates 0>; + interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "mc"; + phys = <&usbphy 0>; + phy-names = "usb"; + extcon = <&usbphy 0>; + allwinner,sram = <&otg_sram 1>; + status = "disabled"; + }; + usbphy: phy@01c13400 { #phy-cells = <1>; compatible = "allwinner,sun7i-a20-usb-phy"; @@ -794,8 +807,7 @@ clocks = <&apb0_gates 5>; gpio-controller; interrupt-controller; - #interrupt-cells = <2>; - #size-cells = <0>; + #interrupt-cells = <3>; #gpio-cells = <3>; pwm0_pins_a: pwm0@0 { diff --git a/arch/arm/dts/sun8i-a23-a33.dtsi b/arch/arm/dts/sun8i-a23-a33.dtsi index 5cd2e92..9c4a55c 100644 --- a/arch/arm/dts/sun8i-a23-a33.dtsi +++ b/arch/arm/dts/sun8i-a23-a33.dtsi @@ -338,6 +338,8 @@ interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>; clocks = <&ahb1_gates 26>; resets = <&ahb1_rst 26>; + phys = <&usbphy 1>; + phy-names = "usb"; status = "disabled"; }; @@ -347,6 +349,8 @@ interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>; clocks = <&ahb1_gates 29>, <&usb_clk 16>; resets = <&ahb1_rst 29>; + phys = <&usbphy 1>; + phy-names = "usb"; status = "disabled"; }; @@ -357,8 +361,7 @@ clocks = <&apb1_gates 5>; gpio-controller; interrupt-controller; - #address-cells = <1>; - #size-cells = <0>; + #interrupt-cells = <3>; #gpio-cells = <3>; uart0_pins_a: uart0@0 { diff --git a/arch/arm/dts/sun8i-a23-ippo-q8h-v5.dts b/arch/arm/dts/sun8i-a23-ippo-q8h-v5.dts index 95134c6..8d9da68 100644 --- a/arch/arm/dts/sun8i-a23-ippo-q8h-v5.dts +++ b/arch/arm/dts/sun8i-a23-ippo-q8h-v5.dts @@ -125,3 +125,12 @@ pinctrl-0 = <&r_uart_pins_a>; status = "okay"; }; + +&usb_otg { + dr_mode = "host"; + status = "okay"; +}; + +&usbphy { + status = "okay"; +}; diff --git a/arch/arm/dts/sun8i-a23.dtsi b/arch/arm/dts/sun8i-a23.dtsi index 8698f7a..2cc27c7 100644 --- a/arch/arm/dts/sun8i-a23.dtsi +++ b/arch/arm/dts/sun8i-a23.dtsi @@ -58,6 +58,39 @@ clock-output-names = "mbus"; }; }; + + soc@01c00000 { + usb_otg: usb@01c19000 { + compatible = "allwinner,sun6i-a31-musb"; + reg = <0x01c19000 0x0400>; + clocks = <&ahb1_gates 24>; + resets = <&ahb1_rst 24>; + interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "mc"; + phys = <&usbphy 0>; + phy-names = "usb"; + extcon = <&usbphy 0>; + status = "disabled"; + }; + + usbphy: phy@01c19400 { + compatible = "allwinner,sun8i-a23-usb-phy"; + reg = <0x01c19400 0x10>, + <0x01c1a800 0x4>; + reg-names = "phy_ctrl", + "pmu1"; + clocks = <&usb_clk 8>, + <&usb_clk 9>; + clock-names = "usb0_phy", + "usb1_phy"; + resets = <&usb_clk 0>, + <&usb_clk 1>; + reset-names = "usb0_reset", + "usb1_reset"; + status = "disabled"; + #phy-cells = <1>; + }; + }; }; &pio { diff --git a/arch/arm/dts/sun8i-a33-ga10h-v1.1.dts b/arch/arm/dts/sun8i-a33-ga10h-v1.1.dts index da16343..1aefc67 100644 --- a/arch/arm/dts/sun8i-a33-ga10h-v1.1.dts +++ b/arch/arm/dts/sun8i-a33-ga10h-v1.1.dts @@ -131,3 +131,12 @@ pinctrl-0 = <&r_uart_pins_a>; status = "okay"; }; + +&usb_otg { + dr_mode = "host"; + status = "okay"; +}; + +&usbphy { + status = "okay"; +}; diff --git a/arch/arm/dts/sun8i-a33-ippo-q8h-v1.2.dts b/arch/arm/dts/sun8i-a33-ippo-q8h-v1.2.dts index 9777149..a438975 100644 --- a/arch/arm/dts/sun8i-a33-ippo-q8h-v1.2.dts +++ b/arch/arm/dts/sun8i-a33-ippo-q8h-v1.2.dts @@ -1,17 +1,56 @@ /* * Copyright 2015 Hans de Goede <hdegoede@redhat.com> * - * Minimal dts file for the Ippo Q8H V1.2 (A33, 1024x600) for u-boot only + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. * - * SPDX-License-Identifier: GPL-2.0+ or X11 + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. */ /dts-v1/; #include "sun8i-a33.dtsi" +#include "sunxi-common-regulators.dtsi" + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/pinctrl/sun4i-a10.h> / { - model = "Ippo Q8H V1.2 (A33, 1024x600)"; - compatible = "ippo,q8h-v1.2-a33-lcd1024x600", "allwinner,sun8i-a23"; + model = "Ippo Q8H Quad Core Tablet (v1.2)"; + compatible = "ippo,a33-q8h-v1.2", "allwinner,sun8i-a33"; aliases { serial0 = &r_uart; @@ -22,8 +61,73 @@ }; }; +&i2c0 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins_a>; + status = "okay"; +}; + +&i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins_a>; + status = "okay"; +}; + +&lradc { + vref-supply = <®_vcc3v0>; + status = "okay"; + + button@200 { + label = "Volume Up"; + linux,code = <KEY_VOLUMEUP>; + channel = <0>; + voltage = <200000>; + }; + + button@400 { + label = "Volume Down"; + linux,code = <KEY_VOLUMEDOWN>; + channel = <0>; + voltage = <400000>; + }; +}; + +&mmc0 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_q8h>; + vmmc-supply = <®_vcc3v0>; + bus-width = <4>; + cd-gpios = <&pio 1 4 GPIO_ACTIVE_HIGH>; /* PB4 */ + cd-inverted; + status = "okay"; +}; + +&pio { + mmc0_cd_pin_q8h: mmc0_cd_pin@0 { + allwinner,pins = "PB4"; + allwinner,function = "gpio_in"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_PULL_UP>; + }; +}; + &r_uart { pinctrl-names = "default"; pinctrl-0 = <&r_uart_pins_a>; status = "okay"; }; + +/* + * FIXME for now we only support host mode and rely on u-boot to have + * turned on Vbus which is controlled by the axp223 pmic on the board. + * + * Once we have axp223 support we should switch to fully supporting otg. + */ +&usb_otg { + dr_mode = "host"; + status = "okay"; +}; + +&usbphy { + status = "okay"; +}; diff --git a/arch/arm/dts/sun8i-a33-sinlinx-sina33.dts b/arch/arm/dts/sun8i-a33-sinlinx-sina33.dts index 5788c29..1d5390d 100644 --- a/arch/arm/dts/sun8i-a33-sinlinx-sina33.dts +++ b/arch/arm/dts/sun8i-a33-sinlinx-sina33.dts @@ -63,6 +63,10 @@ }; }; +&ehci0 { + status = "okay"; +}; + &lradc { vref-supply = <®_vcc3v0>; status = "okay"; @@ -113,6 +117,10 @@ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>; }; +&ohci0 { + status = "okay"; +}; + &pio { mmc0_cd_pin_sina33: mmc0_cd_pin@0 { allwinner,pins = "PB4"; @@ -127,3 +135,8 @@ pinctrl-0 = <&uart0_pins_b>; status = "okay"; }; + +&usbphy { + status = "okay"; + usb1_vbus-supply = <®_vcc5v0>; /* USB1 VBUS is always on */ +}; diff --git a/arch/arm/dts/sun8i-a33.dtsi b/arch/arm/dts/sun8i-a33.dtsi index 85ee080..faa7d3c 100644 --- a/arch/arm/dts/sun8i-a33.dtsi +++ b/arch/arm/dts/sun8i-a33.dtsi @@ -80,6 +80,39 @@ clock-output-names = "mbus"; }; }; + + soc@01c00000 { + usb_otg: usb@01c19000 { + compatible = "allwinner,sun8i-a33-musb"; + reg = <0x01c19000 0x0400>; + clocks = <&ahb1_gates 24>; + resets = <&ahb1_rst 24>; + interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "mc"; + phys = <&usbphy 0>; + phy-names = "usb"; + extcon = <&usbphy 0>; + status = "disabled"; + }; + + usbphy: phy@01c19400 { + compatible = "allwinner,sun8i-a33-usb-phy"; + reg = <0x01c19400 0x14>, + <0x01c1a800 0x4>; + reg-names = "phy_ctrl", + "pmu1"; + clocks = <&usb_clk 8>, + <&usb_clk 9>; + clock-names = "usb0_phy", + "usb1_phy"; + resets = <&usb_clk 0>, + <&usb_clk 1>; + reset-names = "usb0_reset", + "usb1_reset"; + status = "disabled"; + #phy-cells = <1>; + }; + }; }; &pio { diff --git a/arch/arm/dts/sunxi-common-regulators.dtsi b/arch/arm/dts/sunxi-common-regulators.dtsi index 51cc838..f1953b0 100644 --- a/arch/arm/dts/sunxi-common-regulators.dtsi +++ b/arch/arm/dts/sunxi-common-regulators.dtsi @@ -108,6 +108,7 @@ regulator-name = "usb1-vbus"; regulator-min-microvolt = <5000000>; regulator-max-microvolt = <5000000>; + regulator-boot-on; enable-active-high; gpio = <&pio 7 6 GPIO_ACTIVE_HIGH>; status = "disabled"; @@ -120,6 +121,7 @@ regulator-name = "usb2-vbus"; regulator-min-microvolt = <5000000>; regulator-max-microvolt = <5000000>; + regulator-boot-on; enable-active-high; gpio = <&pio 7 3 GPIO_ACTIVE_HIGH>; status = "disabled"; diff --git a/arch/arm/include/asm/arch-sunxi/clock_sun4i.h b/arch/arm/include/asm/arch-sunxi/clock_sun4i.h index a7e25f4..0088bb9 100644 --- a/arch/arm/include/asm/arch-sunxi/clock_sun4i.h +++ b/arch/arm/include/asm/arch-sunxi/clock_sun4i.h @@ -208,6 +208,8 @@ struct sunxi_ccm_reg { #define CCM_AHB_GATE_DLL (0x1 << 15) #define CCM_AHB_GATE_ACE (0x1 << 16) +#define CCM_PLL3_CTRL_M_SHIFT 0 +#define CCM_PLL3_CTRL_M_MASK (0x7f << CCM_PLL3_CTRL_M_SHIFT) #define CCM_PLL3_CTRL_M(n) (((n) & 0x7f) << 0) #define CCM_PLL3_CTRL_INTEGER_MODE (0x1 << 15) #define CCM_PLL3_CTRL_EN (0x1 << 31) @@ -287,6 +289,12 @@ struct sunxi_ccm_reg { #define CCM_LCD_CH0_CTRL_PLL7 (1 << 24) #define CCM_LCD_CH0_CTRL_PLL3_2X (2 << 24) #define CCM_LCD_CH0_CTRL_PLL7_2X (3 << 24) +#define CCM_LCD_CH0_CTRL_MIPI_PLL 0 /* No mipi pll on sun4i/5i/7i */ +#ifdef CONFIG_MACH_SUN5I +#define CCM_LCD_CH0_CTRL_TVE_RST (0x1 << 29) +#else +#define CCM_LCD_CH0_CTRL_TVE_RST 0 /* No separate tve-rst on sun4i/7i */ +#endif #define CCM_LCD_CH0_CTRL_RST (0x1 << 30) #define CCM_LCD_CH0_CTRL_GATE (0x1 << 31) @@ -342,6 +350,7 @@ struct sunxi_ccm_reg { #ifndef __ASSEMBLY__ void clock_set_pll1(unsigned int hz); void clock_set_pll3(unsigned int hz); +unsigned int clock_get_pll3(void); unsigned int clock_get_pll5p(void); unsigned int clock_get_pll6(void); #endif diff --git a/arch/arm/include/asm/arch-sunxi/clock_sun6i.h b/arch/arm/include/asm/arch-sunxi/clock_sun6i.h index 06c6feb..9b7b90c 100644 --- a/arch/arm/include/asm/arch-sunxi/clock_sun6i.h +++ b/arch/arm/include/asm/arch-sunxi/clock_sun6i.h @@ -179,7 +179,11 @@ struct sunxi_ccm_reg { #define CCM_PLL1_CTRL_P(n) (((n) & 0x3) << 16) #define CCM_PLL1_CTRL_EN (0x1 << 31) +#define CCM_PLL3_CTRL_M_SHIFT 0 +#define CCM_PLL3_CTRL_M_MASK (0xf << CCM_PLL3_CTRL_M_SHIFT) #define CCM_PLL3_CTRL_M(n) ((((n) - 1) & 0xf) << 0) +#define CCM_PLL3_CTRL_N_SHIFT 8 +#define CCM_PLL3_CTRL_N_MASK (0x7f << CCM_PLL3_CTRL_N_SHIFT) #define CCM_PLL3_CTRL_N(n) ((((n) - 1) & 0x7f) << 8) #define CCM_PLL3_CTRL_INTEGER_MODE (0x1 << 24) #define CCM_PLL3_CTRL_EN (0x1 << 31) @@ -198,6 +202,18 @@ struct sunxi_ccm_reg { #define CCM_PLL6_CTRL_K_SHIFT 4 #define CCM_PLL6_CTRL_K_MASK (0x3 << CCM_PLL6_CTRL_K_SHIFT) +#define CCM_MIPI_PLL_CTRL_M_SHIFT 0 +#define CCM_MIPI_PLL_CTRL_M_MASK (0xf << CCM_MIPI_PLL_CTRL_M_SHIFT) +#define CCM_MIPI_PLL_CTRL_M(n) ((((n) - 1) & 0xf) << 0) +#define CCM_MIPI_PLL_CTRL_K_SHIFT 4 +#define CCM_MIPI_PLL_CTRL_K_MASK (0x3 << CCM_MIPI_PLL_CTRL_K_SHIFT) +#define CCM_MIPI_PLL_CTRL_K(n) ((((n) - 1) & 0x3) << 4) +#define CCM_MIPI_PLL_CTRL_N_SHIFT 8 +#define CCM_MIPI_PLL_CTRL_N_MASK (0xf << CCM_MIPI_PLL_CTRL_N_SHIFT) +#define CCM_MIPI_PLL_CTRL_N(n) ((((n) - 1) & 0xf) << 8) +#define CCM_MIPI_PLL_CTRL_LDO_EN (0x3 << 22) +#define CCM_MIPI_PLL_CTRL_EN (0x1 << 31) + #define CCM_PLL11_CTRL_N(n) ((((n) - 1) & 0x3f) << 8) #define CCM_PLL11_CTRL_SIGMA_DELTA_EN (0x1 << 24) #define CCM_PLL11_CTRL_UPD (0x1 << 30) @@ -360,7 +376,10 @@ void clock_set_pll1(unsigned int hz); void clock_set_pll3(unsigned int hz); void clock_set_pll5(unsigned int clk, bool sigma_delta_enable); void clock_set_pll11(unsigned int clk, bool sigma_delta_enable); +void clock_set_mipi_pll(unsigned int hz); +unsigned int clock_get_pll3(void); unsigned int clock_get_pll6(void); +unsigned int clock_get_mipi_pll(void); #endif #endif /* _SUNXI_CLOCK_SUN6I_H */ diff --git a/arch/arm/include/asm/arch-sunxi/display.h b/arch/arm/include/asm/arch-sunxi/display.h index 2cc3916..b64f310 100644 --- a/arch/arm/include/asm/arch-sunxi/display.h +++ b/arch/arm/include/asm/arch-sunxi/display.h @@ -196,7 +196,9 @@ struct sunxi_lcdc_reg { u8 res3[0x44]; /* 0xac */ u32 tcon1_io_polarity; /* 0xf0 */ u32 tcon1_io_tristate; /* 0xf4 */ - u8 res4[0x128]; /* 0xf8 */ + u8 res4[0x108]; /* 0xf8 */ + u32 mux_ctrl; /* 0x200 */ + u8 res5[0x1c]; /* 0x204 */ u32 lvds_ana0; /* 0x220 */ u32 lvds_ana1; /* 0x224 */ }; @@ -385,6 +387,10 @@ struct sunxi_tve_reg { #define SUNXI_LCDC_TCON1_TIMING_H_TOTAL(n) (((n) - 1) << 16) #define SUNXI_LCDC_TCON1_TIMING_V_BP(n) (((n) - 1) << 0) #define SUNXI_LCDC_TCON1_TIMING_V_TOTAL(n) ((n) << 16) +#define SUNXI_LCDC_MUX_CTRL_SRC0_MASK (0xf << 0) +#define SUNXI_LCDC_MUX_CTRL_SRC0(x) ((x) << 0) +#define SUNXI_LCDC_MUX_CTRL_SRC1_MASK (0xf << 4) +#define SUNXI_LCDC_MUX_CTRL_SRC1(x) ((x) << 4) #ifdef CONFIG_SUNXI_GEN_SUN6I #define SUNXI_LCDC_LVDS_ANA0 0x40040320 #define SUNXI_LCDC_LVDS_ANA0_EN_MB (1 << 31) @@ -506,7 +512,11 @@ struct sunxi_tve_reg { #define SUNXI_TVE_CFG0_PAL 0x07030001 #define SUNXI_TVE_CFG0_NTSC 0x07030000 #define SUNXI_TVE_DAC_CFG0_VGA 0x403e1ac7 +#ifdef CONFIG_MACH_SUN5I +#define SUNXI_TVE_DAC_CFG0_COMPOSITE 0x433f0009 +#else #define SUNXI_TVE_DAC_CFG0_COMPOSITE 0x403f0008 +#endif #define SUNXI_TVE_FILTER_COMPOSITE 0x00000120 #define SUNXI_TVE_CHROMA_FREQ_PAL_M 0x21e6efe3 #define SUNXI_TVE_CHROMA_FREQ_PAL_NC 0x21f69446 |