diff options
Diffstat (limited to 'board/engicam/isiotmx6ul/isiotmx6ul.c')
| -rw-r--r-- | board/engicam/isiotmx6ul/isiotmx6ul.c | 119 |
1 files changed, 0 insertions, 119 deletions
diff --git a/board/engicam/isiotmx6ul/isiotmx6ul.c b/board/engicam/isiotmx6ul/isiotmx6ul.c index d6a63d2..fa36519 100644 --- a/board/engicam/isiotmx6ul/isiotmx6ul.c +++ b/board/engicam/isiotmx6ul/isiotmx6ul.c @@ -163,21 +163,8 @@ int dram_init(void) } #ifdef CONFIG_SPL_BUILD -#include <libfdt.h> #include <spl.h> -#include <asm/arch/crm_regs.h> -#include <asm/arch/mx6-ddr.h> - -#define UART_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \ - PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \ - PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS) - -static iomux_v3_cfg_t const uart1_pads[] = { - IOMUX_PADS(PAD_UART1_TX_DATA__UART1_DCE_TX | MUX_PAD_CTRL(UART_PAD_CTRL)), - IOMUX_PADS(PAD_UART1_RX_DATA__UART1_DCE_RX | MUX_PAD_CTRL(UART_PAD_CTRL)), -}; - /* MMC board initialization is needed till adding DM support in SPL */ #if defined(CONFIG_FSL_ESDHC) && !defined(CONFIG_DM_MMC) #include <mmc.h> @@ -304,110 +291,4 @@ void board_boot_order(u32 *spl_boot_list) } #endif #endif /* CONFIG_FSL_ESDHC */ - -static struct mx6ul_iomux_grp_regs mx6_grp_ioregs = { - .grp_addds = 0x00000030, - .grp_ddrmode_ctl = 0x00020000, - .grp_b0ds = 0x00000030, - .grp_ctlds = 0x00000030, - .grp_b1ds = 0x00000030, - .grp_ddrpke = 0x00000000, - .grp_ddrmode = 0x00020000, - .grp_ddr_type = 0x000c0000, -}; - -static struct mx6ul_iomux_ddr_regs mx6_ddr_ioregs = { - .dram_dqm0 = 0x00000030, - .dram_dqm1 = 0x00000030, - .dram_ras = 0x00000030, - .dram_cas = 0x00000030, - .dram_odt0 = 0x00000030, - .dram_odt1 = 0x00000030, - .dram_sdba2 = 0x00000000, - .dram_sdclk_0 = 0x00000008, - .dram_sdqs0 = 0x00000038, - .dram_sdqs1 = 0x00000030, - .dram_reset = 0x00000030, -}; - -static struct mx6_mmdc_calibration mx6_mmcd_calib = { - .p0_mpwldectrl0 = 0x00070007, - .p0_mpdgctrl0 = 0x41490145, - .p0_mprddlctl = 0x40404546, - .p0_mpwrdlctl = 0x4040524D, -}; - -struct mx6_ddr_sysinfo ddr_sysinfo = { - .dsize = 0, - .cs_density = 20, - .ncs = 1, - .cs1_mirror = 0, - .rtt_wr = 2, - .rtt_nom = 1, /* RTT_Nom = RZQ/2 */ - .walat = 1, /* Write additional latency */ - .ralat = 5, /* Read additional latency */ - .mif3_mode = 3, /* Command prediction working mode */ - .bi_on = 1, /* Bank interleaving enabled */ - .sde_to_rst = 0x10, /* 14 cycles, 200us (JEDEC default) */ - .rst_to_cke = 0x23, /* 33 cycles, 500us (JEDEC default) */ - .ddr_type = DDR_TYPE_DDR3, -}; - -static struct mx6_ddr3_cfg mem_ddr = { - .mem_speed = 800, - .density = 4, - .width = 16, - .banks = 8, - .rowaddr = 15, - .coladdr = 10, - .pagesz = 2, - .trcd = 1375, - .trcmin = 4875, - .trasmin = 3500, -}; - -static void ccgr_init(void) -{ - struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR; - - writel(0x00c03f3f, &ccm->CCGR0); - writel(0xfcffff00, &ccm->CCGR1); - writel(0x0cffffcc, &ccm->CCGR2); - writel(0x3f3c3030, &ccm->CCGR3); - writel(0xff00fffc, &ccm->CCGR4); - writel(0x033f30ff, &ccm->CCGR5); - writel(0x00c00fff, &ccm->CCGR6); -} - -static void spl_dram_init(void) -{ - mx6ul_dram_iocfg(mem_ddr.width, &mx6_ddr_ioregs, &mx6_grp_ioregs); - mx6_dram_cfg(&ddr_sysinfo, &mx6_mmcd_calib, &mem_ddr); -} - -void board_init_f(ulong dummy) -{ - /* setup AIPS and disable watchdog */ - arch_cpu_init(); - - ccgr_init(); - - /* iomux and setup of i2c */ - SETUP_IOMUX_PADS(uart1_pads); - - /* setup GP timer */ - timer_init(); - - /* UART clocks enabled and gd valid - init serial console */ - preloader_console_init(); - - /* DDR initialization */ - spl_dram_init(); - - /* Clear the BSS. */ - memset(__bss_start, 0, __bss_end - __bss_start); - - /* load/boot image from boot device */ - board_init_r(NULL, 0); -} #endif /* CONFIG_SPL_BUILD */ |