5 files changed, 300 insertions, 0 deletions
diff --git a/board/engicam/isiotmx6ul/Kconfig b/board/engicam/isiotmx6ul/Kconfig
new file mode 100644
index 0000000..213ffad
--- /dev/null
+++ b/board/engicam/isiotmx6ul/Kconfig
@@ -0,0 +1,12 @@
+if TARGET_MX6UL_ISIOT
+
+config SYS_BOARD
+	default "isiotmx6ul"
+
+config SYS_VENDOR
+	default "engicam"
+
+config SYS_CONFIG_NAME
+	default "imx6ul_isiot"
+
+endif
diff --git a/board/engicam/isiotmx6ul/MAINTAINERS b/board/engicam/isiotmx6ul/MAINTAINERS
new file mode 100644
index 0000000..558e516
--- /dev/null
+++ b/board/engicam/isiotmx6ul/MAINTAINERS
@@ -0,0 +1,8 @@
+ISIOTMX6UL BOARD
+M:	Jagan Teki <jagan@amarulasolutions.com>
+S:	Maintained
+F:	board/engicam/isiotmx6ul
+F:	include/configs/imx6ul_isiot.h
+F:	configs/imx6ul_isiot_mmc_defconfig
+F:	arch/arm/dts/imx6ul-isiot.dtsi
+F:	arch/arm/dts/imx6ul-isiot-mmc.dts
diff --git a/board/engicam/isiotmx6ul/Makefile b/board/engicam/isiotmx6ul/Makefile
new file mode 100644
index 0000000..f4f8c78
--- /dev/null
+++ b/board/engicam/isiotmx6ul/Makefile
@@ -0,0 +1,6 @@
+# Copyright (C) 2016 Amarula Solutions B.V.
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+obj-y  := isiotmx6ul.o
diff --git a/board/engicam/isiotmx6ul/README b/board/engicam/isiotmx6ul/README
new file mode 100644
index 0000000..1d177ac
--- /dev/null
+++ b/board/engicam/isiotmx6ul/README
@@ -0,0 +1,28 @@
+How to use U-Boot on Engicam Is.IoT MX6UL Starter Kit:
+-----------------------------------------------------
+
+- Configure U-Boot for Engicam Is.IoT MX6UL
+
+$ make mrproper
+$ make imx6ul_isiot_mmc_defconfig
+$ make
+
+This will generate the SPL image called SPL and the u-boot-dtb.img.
+
+- Flash the SPL image into the micro SD card:
+
+sudo dd if=SPL of=/dev/mmcblk0 bs=1k seek=1; sync
+
+- Flash the u-boot-dtb.img image into the micro SD card:
+
+sudo dd if=u-boot-dtb.img of=/dev/mmcblk0 bs=1k seek=69; sync
+
+- Jumper settings:
+
+MMC Boot: JM3 Closed
+
+- Connect the Serial cable between the Starter Kit and the PC for the console.
+(J28 is the Linux Serial console connector)
+
+- Insert the micro SD card in the board, power it up and U-Boot messages should
+come up.
diff --git a/board/engicam/isiotmx6ul/isiotmx6ul.c b/board/engicam/isiotmx6ul/isiotmx6ul.c
new file mode 100644
index 0000000..b1372d0
--- /dev/null
+++ b/board/engicam/isiotmx6ul/isiotmx6ul.c
@@ -0,0 +1,246 @@
+/*
+ * Copyright (C) 2016 Amarula Solutions B.V.
+ * Copyright (C) 2016 Engicam S.r.l.
+ * Author: Jagan Teki <jagan@amarulasolutions.com>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+
+#include <asm/io.h>
+#include <asm/gpio.h>
+#include <linux/sizes.h>
+
+#include <asm/arch/clock.h>
+#include <asm/arch/crm_regs.h>
+#include <asm/arch/iomux.h>
+#include <asm/arch/mx6-pins.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/imx-common/iomux-v3.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define UART_PAD_CTRL  (PAD_CTL_PKE | PAD_CTL_PUE | \
+			PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
+			PAD_CTL_DSE_40ohm   | PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
+
+static iomux_v3_cfg_t const uart1_pads[] = {
+	MX6_PAD_UART1_TX_DATA__UART1_DCE_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_UART1_RX_DATA__UART1_DCE_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+int board_early_init_f(void)
+{
+	imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
+
+	return 0;
+}
+
+int board_init(void)
+{
+	/* Address of boot parameters */
+	gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
+
+	return 0;
+}
+
+int dram_init(void)
+{
+	gd->ram_size = imx_ddr_size();
+
+	return 0;
+}
+
+#ifdef CONFIG_SPL_BUILD
+#include <libfdt.h>
+#include <spl.h>
+
+#include <asm/arch/crm_regs.h>
+#include <asm/arch/mx6-ddr.h>
+
+/* MMC board initialization is needed till adding DM support in SPL */
+#if defined(CONFIG_FSL_ESDHC) && !defined(CONFIG_DM_MMC)
+#include <mmc.h>
+#include <fsl_esdhc.h>
+
+#define USDHC_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE |             \
+	PAD_CTL_PUS_22K_UP  | PAD_CTL_SPEED_LOW |               \
+	PAD_CTL_DSE_80ohm   | PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
+
+static iomux_v3_cfg_t const usdhc1_pads[] = {
+	MX6_PAD_SD1_CLK__USDHC1_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD1_CMD__USDHC1_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD1_DATA0__USDHC1_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD1_DATA1__USDHC1_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD1_DATA2__USDHC1_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD1_DATA3__USDHC1_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+
+	/* VSELECT */
+	MX6_PAD_GPIO1_IO05__USDHC1_VSELECT | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	/* CD */
+	MX6_PAD_UART1_RTS_B__GPIO1_IO19 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	/* RST_B */
+	MX6_PAD_GPIO1_IO09__GPIO1_IO09 | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+#define USDHC1_CD_GPIO	IMX_GPIO_NR(1, 19)
+
+struct fsl_esdhc_cfg usdhc_cfg[1] = {
+	{USDHC1_BASE_ADDR, 0, 4},
+};
+
+int board_mmc_getcd(struct mmc *mmc)
+{
+	struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
+	int ret = 0;
+
+	switch (cfg->esdhc_base) {
+	case USDHC1_BASE_ADDR:
+		ret = !gpio_get_value(USDHC1_CD_GPIO);
+		break;
+	}
+
+	return ret;
+}
+
+int board_mmc_init(bd_t *bis)
+{
+	int i, ret;
+
+	/*
+	* According to the board_mmc_init() the following map is done:
+	* (U-boot device node)    (Physical Port)
+	* mmc0				USDHC1
+	*/
+	for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
+		switch (i) {
+		case 0:
+			imx_iomux_v3_setup_multiple_pads(
+				usdhc1_pads, ARRAY_SIZE(usdhc1_pads));
+			gpio_direction_input(USDHC1_CD_GPIO);
+			usdhc_cfg[i].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
+			break;
+		default:
+			printf("Warning - USDHC%d controller not supporting\n",
+			       i + 1);
+			return 0;
+		}
+
+		ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]);
+		if (ret) {
+			printf("Warning: failed to initialize mmc dev %d\n", i);
+			return ret;
+		}
+	}
+
+	return 0;
+}
+#endif /* CONFIG_FSL_ESDHC */
+
+static struct mx6ul_iomux_grp_regs mx6_grp_ioregs = {
+	.grp_addds = 0x00000030,
+	.grp_ddrmode_ctl = 0x00020000,
+	.grp_b0ds = 0x00000030,
+	.grp_ctlds = 0x00000030,
+	.grp_b1ds = 0x00000030,
+	.grp_ddrpke = 0x00000000,
+	.grp_ddrmode = 0x00020000,
+	.grp_ddr_type = 0x000c0000,
+};
+
+static struct mx6ul_iomux_ddr_regs mx6_ddr_ioregs = {
+	.dram_dqm0 = 0x00000030,
+	.dram_dqm1 = 0x00000030,
+	.dram_ras = 0x00000030,
+	.dram_cas = 0x00000030,
+	.dram_odt0 = 0x00000030,
+	.dram_odt1 = 0x00000030,
+	.dram_sdba2 = 0x00000000,
+	.dram_sdclk_0 = 0x00000008,
+	.dram_sdqs0 = 0x00000038,
+	.dram_sdqs1 = 0x00000030,
+	.dram_reset = 0x00000030,
+};
+
+static struct mx6_mmdc_calibration mx6_mmcd_calib = {
+	.p0_mpwldectrl0 = 0x00070007,
+	.p0_mpdgctrl0 = 0x41490145,
+	.p0_mprddlctl = 0x40404546,
+	.p0_mpwrdlctl = 0x4040524D,
+};
+
+struct mx6_ddr_sysinfo ddr_sysinfo = {
+	.dsize = 0,
+	.cs_density = 20,
+	.ncs = 1,
+	.cs1_mirror = 0,
+	.rtt_wr = 2,
+	.rtt_nom = 1,		/* RTT_Nom = RZQ/2 */
+	.walat = 1,		/* Write additional latency */
+	.ralat = 5,		/* Read additional latency */
+	.mif3_mode = 3,		/* Command prediction working mode */
+	.bi_on = 1,		/* Bank interleaving enabled */
+	.sde_to_rst = 0x10,	/* 14 cycles, 200us (JEDEC default) */
+	.rst_to_cke = 0x23,	/* 33 cycles, 500us (JEDEC default) */
+	.ddr_type = DDR_TYPE_DDR3,
+};
+
+static struct mx6_ddr3_cfg mem_ddr = {
+	.mem_speed = 800,
+	.density = 4,
+	.width = 16,
+	.banks = 8,
+	.rowaddr = 15,
+	.coladdr = 10,
+	.pagesz = 2,
+	.trcd = 1375,
+	.trcmin = 4875,
+	.trasmin = 3500,
+};
+
+static void ccgr_init(void)
+{
+	struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+
+	writel(0x00c03f3f, &ccm->CCGR0);
+	writel(0xfcffff00, &ccm->CCGR1);
+	writel(0x0cffffcc, &ccm->CCGR2);
+	writel(0x3f3c3030, &ccm->CCGR3);
+	writel(0xff00fffc, &ccm->CCGR4);
+	writel(0x033f30ff, &ccm->CCGR5);
+	writel(0x00c00fff, &ccm->CCGR6);
+}
+
+static void spl_dram_init(void)
+{
+	mx6ul_dram_iocfg(mem_ddr.width, &mx6_ddr_ioregs, &mx6_grp_ioregs);
+	mx6_dram_cfg(&ddr_sysinfo, &mx6_mmcd_calib, &mem_ddr);
+}
+
+void board_init_f(ulong dummy)
+{
+	/* setup AIPS and disable watchdog */
+	arch_cpu_init();
+
+	ccgr_init();
+
+	/* iomux and setup of i2c */
+	board_early_init_f();
+
+	/* setup GP timer */
+	timer_init();
+
+	/* UART clocks enabled and gd valid - init serial console */
+	preloader_console_init();
+
+	/* DDR initialization */
+	spl_dram_init();
+
+	/* Clear the BSS. */
+	memset(__bss_start, 0, __bss_end - __bss_start);
+
+	/* load/boot image from boot device */
+	board_init_r(NULL, 0);
+}
+#endif /* CONFIG_SPL_BUILD */