summaryrefslogtreecommitdiff
path: root/board/esd/hh405/hh405.c
diff options
context:
space:
mode:
Diffstat (limited to 'board/esd/hh405/hh405.c')
-rw-r--r--board/esd/hh405/hh405.c419
1 files changed, 406 insertions, 13 deletions
diff --git a/board/esd/hh405/hh405.c b/board/esd/hh405/hh405.c
index 64690ac..67a0c30 100644
--- a/board/esd/hh405/hh405.c
+++ b/board/esd/hh405/hh405.c
@@ -2,6 +2,9 @@
* (C) Copyright 2001-2004
* Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
*
+ * (C) Copyright 2005
+ * Stefan Roese, DENX Software Engineering, sr@denx.de.
+ *
* See file CREDITS for list of people who contributed to this
* project.
*
@@ -25,8 +28,176 @@
#include <asm/processor.h>
#include <command.h>
#include <malloc.h>
+#include <pci.h>
+#include <sm501.h>
+
+
+#ifdef CONFIG_VIDEO_SM501
+
+#define SWAP32(x) ((((x) & 0x000000ff) << 24) | (((x) & 0x0000ff00) << 8)|\
+ (((x) & 0x00ff0000) >> 8) | (((x) & 0xff000000) >> 24) )
+
+#ifdef CONFIG_VIDEO_SM501_8BPP
+#error CONFIG_VIDEO_SM501_8BPP not supported.
+#endif /* CONFIG_VIDEO_SM501_8BPP */
+
+#ifdef CONFIG_VIDEO_SM501_16BPP
+#define BPP 16
+
+/*
+ * 800x600 display B084SN03: PCLK = 40MHz
+ * => 2*PCLK = 80MHz
+ * 336/4 = 84MHz
+ * => PCLK = 84MHz
+ */
+static const SMI_REGS init_regs_800x600 [] =
+{
+#if 1 /* test-only */
+ {0x0005c, SWAP32(0xffffffff)}, /* set endianess to big endian */
+#else
+ {0x0005c, SWAP32(0x00000000)}, /* set endianess to little endian */
+#endif
+ {0x00004, SWAP32(0x00000000)},
+ /* clocks for pm1... */
+ {0x00048, SWAP32(0x00021807)},
+ {0x0004C, SWAP32(0x221a0a01)},
+ {0x00054, SWAP32(0x00000001)},
+ /* clocks for pm0... */
+ {0x00040, SWAP32(0x00021807)},
+ {0x00044, SWAP32(0x221a0a01)},
+ {0x00054, SWAP32(0x00000000)},
+ /* panel control regs... */
+ {0x80000, SWAP32(0x0f013105)}, /* panel display control: 16-bit RGB 5:6:5 mode */
+ {0x80004, SWAP32(0xc428bb17)}, /* panel panning control ??? */
+ {0x8000C, SWAP32(0x00000000)}, /* panel fb address */
+ {0x80010, SWAP32(0x06400640)}, /* panel fb offset/window width */
+ {0x80014, SWAP32(0x03200000)}, /* panel fb width (0x320=800) */
+ {0x80018, SWAP32(0x02580000)}, /* panel fb height (0x258=600) */
+ {0x8001C, SWAP32(0x00000000)}, /* panel plane tl location */
+ {0x80020, SWAP32(0x02580320)}, /* panel plane br location */
+ {0x80024, SWAP32(0x041f031f)}, /* panel horizontal total */
+ {0x80028, SWAP32(0x00800347)}, /* panel horizontal sync */
+ {0x8002C, SWAP32(0x02730257)}, /* panel vertical total */
+ {0x80030, SWAP32(0x00040258)}, /* panel vertical sync */
+ {0x80200, SWAP32(0x00010000)}, /* crt display control */
+ {0, 0}
+};
+
+/*
+ * 1024x768 display G150XG02: PCLK = 65MHz
+ * => 2*PCLK = 130MHz
+ * 288/2 = 144MHz
+ * => PCLK = 72MHz
+ */
+static const SMI_REGS init_regs_1024x768 [] =
+{
+ {0x00004, SWAP32(0x00000000)},
+ /* clocks for pm1... */
+ {0x00048, SWAP32(0x00021807)},
+ {0x0004C, SWAP32(0x011a0a01)},
+ {0x00054, SWAP32(0x00000001)},
+ /* clocks for pm0... */
+ {0x00040, SWAP32(0x00021807)},
+ {0x00044, SWAP32(0x011a0a01)},
+ {0x00054, SWAP32(0x00000000)},
+ /* panel control regs... */
+ {0x80000, SWAP32(0x0f013105)}, /* panel display control: 16-bit RGB 5:6:5 mode */
+ {0x80004, SWAP32(0xc428bb17)}, /* panel panning control ??? */
+ {0x8000C, SWAP32(0x00000000)}, /* panel fb address */
+ {0x80010, SWAP32(0x08000800)}, /* panel fb offset/window width */
+ {0x80014, SWAP32(0x04000000)}, /* panel fb width (0x400=1024) */
+ {0x80018, SWAP32(0x03000000)}, /* panel fb height (0x300=768) */
+ {0x8001C, SWAP32(0x00000000)}, /* panel plane tl location */
+ {0x80020, SWAP32(0x03000400)}, /* panel plane br location */
+ {0x80024, SWAP32(0x053f03ff)}, /* panel horizontal total */
+ {0x80028, SWAP32(0x0140040f)}, /* panel horizontal sync */
+ {0x8002C, SWAP32(0x032502ff)}, /* panel vertical total */
+ {0x80030, SWAP32(0x00260301)}, /* panel vertical sync */
+ {0x80200, SWAP32(0x00010000)}, /* crt display control */
+ {0, 0}
+};
-/* ------------------------------------------------------------------------- */
+#endif /* CONFIG_VIDEO_SM501_16BPP */
+
+#ifdef CONFIG_VIDEO_SM501_32BPP
+#define BPP 32
+
+/*
+ * 800x600 display B084SN03: PCLK = 40MHz
+ * => 2*PCLK = 80MHz
+ * 336/4 = 84MHz
+ * => PCLK = 84MHz
+ */
+static const SMI_REGS init_regs_800x600 [] =
+{
+#if 0 /* test-only */
+ {0x0005c, SWAP32(0xffffffff)}, /* set endianess to big endian */
+#else
+ {0x0005c, SWAP32(0x00000000)}, /* set endianess to little endian */
+#endif
+ {0x00004, SWAP32(0x00000000)},
+ /* clocks for pm1... */
+ {0x00048, SWAP32(0x00021807)},
+ {0x0004C, SWAP32(0x221a0a01)},
+ {0x00054, SWAP32(0x00000001)},
+ /* clocks for pm0... */
+ {0x00040, SWAP32(0x00021807)},
+ {0x00044, SWAP32(0x221a0a01)},
+ {0x00054, SWAP32(0x00000000)},
+ /* panel control regs... */
+ {0x80000, SWAP32(0x0f013106)}, /* panel display control: 32-bit RGB 8:8:8 mode */
+ {0x80004, SWAP32(0xc428bb17)}, /* panel panning control ??? */
+ {0x8000C, SWAP32(0x00000000)}, /* panel fb address */
+ {0x80010, SWAP32(0x0c800c80)}, /* panel fb offset/window width */
+ {0x80014, SWAP32(0x03200000)}, /* panel fb width (0x320=800) */
+ {0x80018, SWAP32(0x02580000)}, /* panel fb height (0x258=600) */
+ {0x8001C, SWAP32(0x00000000)}, /* panel plane tl location */
+ {0x80020, SWAP32(0x02580320)}, /* panel plane br location */
+ {0x80024, SWAP32(0x041f031f)}, /* panel horizontal total */
+ {0x80028, SWAP32(0x00800347)}, /* panel horizontal sync */
+ {0x8002C, SWAP32(0x02730257)}, /* panel vertical total */
+ {0x80030, SWAP32(0x00040258)}, /* panel vertical sync */
+ {0x80200, SWAP32(0x00010000)}, /* crt display control */
+ {0, 0}
+};
+
+/*
+ * 1024x768 display G150XG02: PCLK = 65MHz
+ * => 2*PCLK = 130MHz
+ * 288/2 = 144MHz
+ * => PCLK = 72MHz
+ */
+static const SMI_REGS init_regs_1024x768 [] =
+{
+ {0x00004, SWAP32(0x00000000)},
+ /* clocks for pm1... */
+ {0x00048, SWAP32(0x00021807)},
+ {0x0004C, SWAP32(0x011a0a01)},
+ {0x00054, SWAP32(0x00000001)},
+ /* clocks for pm0... */
+ {0x00040, SWAP32(0x00021807)},
+ {0x00044, SWAP32(0x011a0a01)},
+ {0x00054, SWAP32(0x00000000)},
+ /* panel control regs... */
+ {0x80000, SWAP32(0x0f013106)}, /* panel display control: 32-bit RGB 8:8:8 mode */
+ {0x80004, SWAP32(0xc428bb17)}, /* panel panning control ??? */
+ {0x8000C, SWAP32(0x00000000)}, /* panel fb address */
+ {0x80010, SWAP32(0x10001000)}, /* panel fb offset/window width */
+ {0x80014, SWAP32(0x04000000)}, /* panel fb width (0x400=1024) */
+ {0x80018, SWAP32(0x03000000)}, /* panel fb height (0x300=768) */
+ {0x8001C, SWAP32(0x00000000)}, /* panel plane tl location */
+ {0x80020, SWAP32(0x03000400)}, /* panel plane br location */
+ {0x80024, SWAP32(0x053f03ff)}, /* panel horizontal total */
+ {0x80028, SWAP32(0x0140040f)}, /* panel horizontal sync */
+ {0x8002C, SWAP32(0x032502ff)}, /* panel vertical total */
+ {0x80030, SWAP32(0x00260301)}, /* panel vertical sync */
+ {0x80200, SWAP32(0x00010000)}, /* crt display control */
+ {0, 0}
+};
+
+#endif /* CONFIG_VIDEO_SM501_32BPP */
+
+#endif /* CONFIG_VIDEO_SM501 */
#if 0
#define FPGA_DEBUG
@@ -134,14 +305,15 @@ int board_revision(void)
if (value & 0x80000000) {
/* Revision 1.0 or 1.1 detected */
- return 1;
+ return 0x0101;
} else {
if (value & 0x00400000) {
- /* Revision 1.3 detected */
- return 3;
+ /* unused */
+ return 0x0103;
} else {
- /* Revision 1.2 detected */
- return 2;
+ /* Revision >= 2.0 detected */
+ /* rev. 2.x uses four SM501 GPIOs for revision coding */
+ return 0x0200;
}
}
}
@@ -195,6 +367,7 @@ int misc_init_r (void)
int i;
char *str;
unsigned long contrast0 = 0xffffffff;
+ pci_dev_t devbusfn;
dst = malloc(CFG_FPGA_MAX_SIZE);
if (gunzip (dst, CFG_FPGA_MAX_SIZE, (uchar *)fpgadata, &len) != 0) {
@@ -261,10 +434,15 @@ int misc_init_r (void)
* Write Board revision into FPGA
*/
*fpga_ctrl |= gd->board_type & 0x0003;
- if (gd->board_type >= 2) {
+ if (gd->board_type >= 0x0200) {
*fpga_ctrl |= CFG_FPGA_CTRL_CF_BUS_EN;
}
+ /*
+ * Setup and enable EEPROM write protection
+ */
+ out32(GPIO0_OR, in32(GPIO0_OR) | CFG_EEPROM_WP);
+
/*
* Set NAND-FLASH GPIO signals to default
*/
@@ -301,6 +479,7 @@ int misc_init_r (void)
/*
* Init lcd interface and display logo
*/
+
str = getenv("bd_type");
if (strcmp(str, "ppc230") == 0) {
/*
@@ -376,8 +555,24 @@ int misc_init_r (void)
sizeof(regs_13704_320_240_4bpp)/sizeof(regs_13704_320_240_4bpp[0]),
logo_bmp_320, sizeof(logo_bmp_320));
} else {
- printf("Unsupported bd_type defined (%s) -> No display configured!\n", str);
- return 0;
+ /*
+ * Is SM501 connected (ppc221/ppc231)?
+ */
+ devbusfn = pci_find_device(PCI_VENDOR_SM, PCI_DEVICE_SM501, 0);
+ if (devbusfn != -1) {
+ puts("VGA: SM501 with 8 MB ");
+ if (strcmp(str, "ppc221") == 0) {
+ printf("(800*600, %dbpp)\n", BPP);
+ } else if (strcmp(str, "ppc231") == 0) {
+ printf("(1024*768, %dbpp)\n", BPP);
+ } else {
+ printf("Unsupported bd_type defined (%s) -> No display configured!\n", str);
+ return 0;
+ }
+ } else {
+ printf("Unsupported bd_type defined (%s) -> No display configured!\n", str);
+ return 0;
+ }
}
return (0);
@@ -410,7 +605,9 @@ int checkboard (void)
}
gd->board_type = board_revision();
- printf(", Rev 1.%ld)\n", gd->board_type);
+ printf(", Rev %ld.%ld)\n",
+ (gd->board_type >> 8) & 0xff,
+ gd->board_type & 0xff);
/*
* Disable sleep mode in LXT971
@@ -420,7 +617,6 @@ int checkboard (void)
return 0;
}
-/* ------------------------------------------------------------------------- */
long int initdram (int board_type)
{
@@ -437,7 +633,6 @@ long int initdram (int board_type)
return (4*1024*1024 << ((val & 0x000e0000) >> 17));
}
-/* ------------------------------------------------------------------------- */
int testdram (void)
{
@@ -447,7 +642,6 @@ int testdram (void)
return (0);
}
-/* ------------------------------------------------------------------------- */
#ifdef CONFIG_IDE_RESET
void ide_set_reset(int on)
@@ -479,3 +673,202 @@ void nand_init(void)
}
}
#endif
+
+
+#if defined(CFG_EEPROM_WREN)
+/* Input: <dev_addr> I2C address of EEPROM device to enable.
+ * <state> -1: deliver current state
+ * 0: disable write
+ * 1: enable write
+ * Returns: -1: wrong device address
+ * 0: dis-/en- able done
+ * 0/1: current state if <state> was -1.
+ */
+int eeprom_write_enable (unsigned dev_addr, int state)
+{
+ if (CFG_I2C_EEPROM_ADDR != dev_addr) {
+ return -1;
+ } else {
+ switch (state) {
+ case 1:
+ /* Enable write access, clear bit GPIO_SINT2. */
+ out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_EEPROM_WP);
+ state = 0;
+ break;
+ case 0:
+ /* Disable write access, set bit GPIO_SINT2. */
+ out32(GPIO0_OR, in32(GPIO0_OR) | CFG_EEPROM_WP);
+ state = 0;
+ break;
+ default:
+ /* Read current status back. */
+ state = (0 == (in32(GPIO0_OR) & CFG_EEPROM_WP));
+ break;
+ }
+ }
+ return state;
+}
+
+int do_eep_wren (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
+{
+ int query = argc == 1;
+ int state = 0;
+
+ if (query) {
+ /* Query write access state. */
+ state = eeprom_write_enable (CFG_I2C_EEPROM_ADDR, -1);
+ if (state < 0) {
+ puts ("Query of write access state failed.\n");
+ } else {
+ printf ("Write access for device 0x%0x is %sabled.\n",
+ CFG_I2C_EEPROM_ADDR, state ? "en" : "dis");
+ state = 0;
+ }
+ } else {
+ if ('0' == argv[1][0]) {
+ /* Disable write access. */
+ state = eeprom_write_enable (CFG_I2C_EEPROM_ADDR, 0);
+ } else {
+ /* Enable write access. */
+ state = eeprom_write_enable (CFG_I2C_EEPROM_ADDR, 1);
+ }
+ if (state < 0) {
+ puts ("Setup of write access state failed.\n");
+ }
+ }
+
+ return state;
+}
+
+U_BOOT_CMD(eepwren, 2, 0, do_eep_wren,
+ "eepwren - Enable / disable / query EEPROM write access\n",
+ NULL);
+#endif /* #if defined(CFG_EEPROM_WREN) */
+
+
+#ifdef CONFIG_VIDEO_SM501
+#ifdef CONFIG_CONSOLE_EXTRA_INFO
+/*
+ * Return text to be printed besides the logo.
+ */
+void video_get_info_str (int line_number, char *info)
+{
+ DECLARE_GLOBAL_DATA_PTR;
+
+ char str[64];
+ char str2[64];
+ int i = getenv_r("serial#", str2, sizeof(str));
+
+ if (line_number == 1) {
+ sprintf(str, " Board: ");
+
+ if (i == -1) {
+ strcat(str, "### No HW ID - assuming HH405");
+ } else {
+ strcat(str, str2);
+ }
+
+ if (getenv_r("bd_type", str2, sizeof(str2)) != -1) {
+ strcat(str, " (");
+ strcat(str, str2);
+ } else {
+ strcat(str, " (Missing bd_type!");
+ }
+
+ sprintf(str2, ", Rev %ld.%ld)",
+ (gd->board_type >> 8) & 0xff, gd->board_type & 0xff);
+ strcat(str, str2);
+ strcpy(info, str);
+ } else {
+ info [0] = '\0';
+ }
+}
+#endif /* CONFIG_CONSOLE_EXTRA_INFO */
+
+/*
+ * Returns SM501 register base address. First thing called in the driver.
+ */
+unsigned int board_video_init (void)
+{
+ pci_dev_t devbusfn;
+ u32 addr;
+
+ /*
+ * Is SM501 connected (ppc221/ppc231)?
+ */
+ devbusfn = pci_find_device(PCI_VENDOR_SM, PCI_DEVICE_SM501, 0);
+ if (devbusfn != -1) {
+ pci_read_config_dword(devbusfn, PCI_BASE_ADDRESS_1, (u32 *)&addr);
+ return (addr & 0xfffffffe);
+ }
+
+ return 0;
+}
+
+/*
+ * Returns SM501 framebuffer address
+ */
+unsigned int board_video_get_fb (void)
+{
+ pci_dev_t devbusfn;
+ u32 addr;
+
+ /*
+ * Is SM501 connected (ppc221/ppc231)?
+ */
+ devbusfn = pci_find_device(PCI_VENDOR_SM, PCI_DEVICE_SM501, 0);
+ if (devbusfn != -1) {
+ pci_read_config_dword(devbusfn, PCI_BASE_ADDRESS_0, (u32 *)&addr);
+ return (addr & 0xfffffffe);
+ }
+
+ return 0;
+}
+
+/*
+ * Called after initializing the SM501 and before clearing the screen.
+ */
+void board_validate_screen (unsigned int base)
+{
+}
+
+/*
+ * Return a pointer to the initialization sequence.
+ */
+const SMI_REGS *board_get_regs (void)
+{
+ char *str;
+
+ str = getenv("bd_type");
+ if (strcmp(str, "ppc221") == 0) {
+ return init_regs_800x600;
+ } else {
+ return init_regs_1024x768;
+ }
+}
+
+int board_get_width (void)
+{
+ char *str;
+
+ str = getenv("bd_type");
+ if (strcmp(str, "ppc221") == 0) {
+ return 800;
+ } else {
+ return 1024;
+ }
+}
+
+int board_get_height (void)
+{
+ char *str;
+
+ str = getenv("bd_type");
+ if (strcmp(str, "ppc221") == 0) {
+ return 600;
+ } else {
+ return 768;
+ }
+}
+
+#endif /* CONFIG_VIDEO_SM501 */