1 files changed, 0 insertions, 303 deletions
diff --git a/board/freescale/p1_p2_rdb/p1_p2_rdb.c b/board/freescale/p1_p2_rdb/p1_p2_rdb.c
deleted file mode 100644
index 61ed466..0000000
--- a/board/freescale/p1_p2_rdb/p1_p2_rdb.c
+++ /dev/null
@@ -1,303 +0,0 @@
-/*
- * Copyright 2009-2011 Freescale Semiconductor, Inc.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#include <common.h>
-#include <command.h>
-#include <asm/processor.h>
-#include <asm/mmu.h>
-#include <asm/cache.h>
-#include <asm/immap_85xx.h>
-#include <asm/fsl_serdes.h>
-#include <asm/io.h>
-#include <miiphy.h>
-#include <libfdt.h>
-#include <fdt_support.h>
-#include <fsl_mdio.h>
-#include <tsec.h>
-#include <vsc7385.h>
-#include <netdev.h>
-#include <rtc.h>
-#include <i2c.h>
-#include <hwconfig.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-#define VSC7385_RST_SET		0x00080000
-#define SLIC_RST_SET		0x00040000
-#define SGMII_PHY_RST_SET	0x00020000
-#define PCIE_RST_SET		0x00010000
-#define RGMII_PHY_RST_SET	0x02000000
-
-#define USB_RST_CLR		0x04000000
-#define USB2_PORT_OUT_EN        0x01000000
-
-#define GPIO_DIR		0x060f0000
-
-#define BOARD_PERI_RST_SET	VSC7385_RST_SET | SLIC_RST_SET | \
-				SGMII_PHY_RST_SET | PCIE_RST_SET | \
-				RGMII_PHY_RST_SET
-
-#define SYSCLK_MASK	0x00200000
-#define BOARDREV_MASK	0x10100000
-#define BOARDREV_C	0x00100000
-#define BOARDREV_D	0x00000000
-
-#define SYSCLK_66	66666666
-#define SYSCLK_100	100000000
-
-unsigned long get_board_sys_clk(ulong dummy)
-{
-	volatile ccsr_gpio_t *pgpio = (void *)(CONFIG_SYS_MPC85xx_GPIO_ADDR);
-	u32 val_gpdat, sysclk_gpio;
-
-	val_gpdat = in_be32(&pgpio->gpdat);
-	sysclk_gpio = val_gpdat & SYSCLK_MASK;
-
-	if(sysclk_gpio == 0)
-		return SYSCLK_66;
-	else
-		return SYSCLK_100;
-
-	return 0;
-}
-
-#ifdef CONFIG_MMC
-int board_early_init_f (void)
-{
-	volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
-
-	setbits_be32(&gur->pmuxcr,
-			(MPC85xx_PMUXCR_SDHC_CD |
-			 MPC85xx_PMUXCR_SDHC_WP));
-	return 0;
-}
-#endif
-
-int checkboard (void)
-{
-	u32 val_gpdat, board_rev_gpio;
-	volatile ccsr_gpio_t *pgpio = (void *)(CONFIG_SYS_MPC85xx_GPIO_ADDR);
-	char board_rev = 0;
-	struct cpu_type *cpu;
-
-	val_gpdat = in_be32(&pgpio->gpdat);
-	board_rev_gpio = val_gpdat & BOARDREV_MASK;
-	if (board_rev_gpio == BOARDREV_C)
-		board_rev = 'C';
-	else if (board_rev_gpio == BOARDREV_D)
-		board_rev = 'D';
-	else
-		panic ("Unexpected Board REV %x detected!!\n", board_rev_gpio);
-
-	cpu = gd->arch.cpu;
-	printf ("Board: %sRDB Rev%c\n", cpu->name, board_rev);
-
-	setbits_be32(&pgpio->gpdir, GPIO_DIR);
-
-/*
- * Bringing the following peripherals out of reset via GPIOs
- * 0 = reset and 1 = out of reset
- * GPIO12 - Reset to Ethernet Switch
- * GPIO13 - Reset to SLIC/SLAC devices
- * GPIO14 - Reset to SGMII_PHY_N
- * GPIO15 - Reset to PCIe slots
- * GPIO6  - Reset to RGMII PHY
- * GPIO5  - Reset to USB3300 devices 1 = reset and 0 = out of reset
- */
-	clrsetbits_be32(&pgpio->gpdat, USB_RST_CLR, BOARD_PERI_RST_SET);
-
-	return 0;
-}
-
-int misc_init_r(void)
-{
-#if defined(CONFIG_SDCARD) || defined(CONFIG_SPIFLASH)
-	ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR;
-	ccsr_gpio_t *gpio = (void *)CONFIG_SYS_MPC85xx_GPIO_ADDR;
-
-	setbits_be32(&gpio->gpdir, USB2_PORT_OUT_EN);
-	setbits_be32(&gpio->gpdat, USB2_PORT_OUT_EN);
-	setbits_be32(&gur->pmuxcr, MPC85xx_PMUXCR_ELBC_OFF_USB2_ON);
-#endif
-	return 0;
-}
-
-int board_early_init_r(void)
-{
-	const unsigned int flashbase = CONFIG_SYS_FLASH_BASE;
-	int flash_esel = find_tlb_idx((void *)flashbase, 1);
-	volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
-	unsigned int orig_bus = i2c_get_bus_num();
-	u8 i2c_data;
-
-	i2c_set_bus_num(1);
-	if (i2c_read(CONFIG_SYS_I2C_PCA9557_ADDR, 0,
-		1, &i2c_data, sizeof(i2c_data)) == 0) {
-		if (i2c_data & 0x2)
-			puts("NOR Flash Bank : Secondary\n");
-		else
-			puts("NOR Flash Bank : Primary\n");
-
-		if (i2c_data & 0x1) {
-			setbits_be32(&gur->pmuxcr, MPC85xx_PMUXCR_SD_DATA);
-			puts("SD/MMC : 8-bit Mode\n");
-			puts("eSPI : Disabled\n");
-		} else {
-			puts("SD/MMC : 4-bit Mode\n");
-			puts("eSPI : Enabled\n");
-		}
-	} else {
-		puts("Failed reading I2C Chip 0x18 on bus 1\n");
-	}
-	i2c_set_bus_num(orig_bus);
-
-	/*
-	 * Remap Boot flash region to caching-inhibited
-	 * so that flash can be erased properly.
-	 */
-
-	/* Flush d-cache and invalidate i-cache of any FLASH data */
-	flush_dcache();
-	invalidate_icache();
-
-	if (flash_esel == -1) {
-		/* very unlikely unless something is messed up */
-		puts("Error: Could not find TLB for FLASH BASE\n");
-		flash_esel = 2;	/* give our best effort to continue */
-	} else {
-		/* invalidate existing TLB entry for flash */
-		disable_tlb(flash_esel);
-	}
-
-	set_tlb(1, flashbase, CONFIG_SYS_FLASH_BASE_PHYS,
-			MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
-			0, flash_esel, BOOKE_PAGESZ_16M, 1);
-	rtc_reset();
-	return 0;
-}
-
-
-#ifdef CONFIG_TSEC_ENET
-int board_eth_init(bd_t *bis)
-{
-	struct fsl_pq_mdio_info mdio_info;
-	struct tsec_info_struct tsec_info[4];
-	int num = 0;
-	char *tmp;
-	unsigned int vscfw_addr;
-
-#ifdef CONFIG_TSEC1
-	SET_STD_TSEC_INFO(tsec_info[num], 1);
-	num++;
-#endif
-#ifdef CONFIG_TSEC2
-	SET_STD_TSEC_INFO(tsec_info[num], 2);
-	num++;
-#endif
-#ifdef CONFIG_TSEC3
-	SET_STD_TSEC_INFO(tsec_info[num], 3);
-	if (is_serdes_configured(SGMII_TSEC3)) {
-		puts("eTSEC3 is in sgmii mode.\n");
-		tsec_info[num].flags |= TSEC_SGMII;
-	}
-	num++;
-#endif
-	if (!num) {
-		printf("No TSECs initialized\n");
-		return 0;
-	}
-#ifdef CONFIG_VSC7385_ENET
-/* If a VSC7385 microcode image is present, then upload it. */
-	if ((tmp = getenv ("vscfw_addr")) != NULL) {
-		vscfw_addr = simple_strtoul (tmp, NULL, 16);
-		printf("uploading VSC7385 microcode from %x\n", vscfw_addr);
-		if (vsc7385_upload_firmware((void *) vscfw_addr,
-					CONFIG_VSC7385_IMAGE_SIZE))
-			puts("Failure uploading VSC7385 microcode.\n");
-	} else
-		puts("No address specified for VSC7385 microcode.\n");
-#endif
-
-	mdio_info.regs = (struct tsec_mii_mng *)CONFIG_SYS_MDIO_BASE_ADDR;
-	mdio_info.name = DEFAULT_MII_NAME;
-	fsl_pq_mdio_init(bis, &mdio_info);
-
-	tsec_eth_init(bis, tsec_info, num);
-
-	return pci_eth_init(bis);
-}
-#endif
-
-#if defined(CONFIG_OF_BOARD_SETUP)
-extern void ft_pci_board_setup(void *blob);
-
-int ft_board_setup(void *blob, bd_t *bd)
-{
-	const char *soc_usb_compat = "fsl-usb2-dr";
-	int err, usb1_off, usb2_off;
-	phys_addr_t base;
-	phys_size_t size;
-
-	ft_cpu_setup(blob, bd);
-
-	base = getenv_bootm_low();
-	size = getenv_bootm_size();
-
-#if defined(CONFIG_PCI)
-	ft_pci_board_setup(blob);
-#endif /* #if defined(CONFIG_PCI) */
-
-	fdt_fixup_memory(blob, (u64)base, (u64)size);
-
-#if defined(CONFIG_HAS_FSL_DR_USB)
-	fdt_fixup_dr_usb(blob, bd);
-#endif
-
-#if defined(CONFIG_SDCARD) || defined(CONFIG_SPIFLASH)
-	/* Delete eLBC node as it is muxed with USB2 controller */
-	if (hwconfig("usb2")) {
-		const char *soc_elbc_compat = "fsl,p1020-elbc";
-		int off = fdt_node_offset_by_compatible(blob, -1,
-			soc_elbc_compat);
-		if (off < 0) {
-			printf("WARNING: could not find compatible node %s\n",
-			       soc_elbc_compat);
-			return off;
-		}
-		err = fdt_del_node(blob, off);
-		if (err < 0) {
-			printf("WARNING: could not remove %s\n",
-			       soc_elbc_compat);
-			return err;
-		}
-		return 0;
-	}
-#endif
-	/* Delete USB2 node as it is muxed with eLBC */
-	usb1_off = fdt_node_offset_by_compatible(blob, -1,
-		soc_usb_compat);
-	if (usb1_off < 0) {
-		printf("WARNING: could not find compatible node %s\n",
-		       soc_usb_compat);
-		return usb1_off;
-	}
-	usb2_off = fdt_node_offset_by_compatible(blob, usb1_off,
-			soc_usb_compat);
-	if (usb2_off < 0) {
-		printf("WARNING: could not find compatible node %s\n",
-		       soc_usb_compat);
-		return usb2_off;
-	}
-	err = fdt_del_node(blob, usb2_off);
-	if (err < 0) {
-		printf("WARNING: could not remove %s\n", soc_usb_compat);
-		return err;
-	}
-
-	return 0;
-}
-
-#endif