diff options
Diffstat (limited to 'board/gateworks')
-rw-r--r-- | board/gateworks/gw_ventana/Makefile | 10 | ||||
-rw-r--r-- | board/gateworks/gw_ventana/README | 55 | ||||
-rw-r--r-- | board/gateworks/gw_ventana/clocks.cfg | 42 | ||||
-rw-r--r-- | board/gateworks/gw_ventana/gsc.c | 129 | ||||
-rw-r--r-- | board/gateworks/gw_ventana/gsc.h | 64 | ||||
-rw-r--r-- | board/gateworks/gw_ventana/gw_ventana.c | 1263 | ||||
-rw-r--r-- | board/gateworks/gw_ventana/gw_ventana.cfg | 44 | ||||
-rw-r--r-- | board/gateworks/gw_ventana/ventana_eeprom.h | 106 |
8 files changed, 1713 insertions, 0 deletions
diff --git a/board/gateworks/gw_ventana/Makefile b/board/gateworks/gw_ventana/Makefile new file mode 100644 index 0000000..e8dab89 --- /dev/null +++ b/board/gateworks/gw_ventana/Makefile @@ -0,0 +1,10 @@ +# +# Copyright (C) 2012-2013, Guennadi Liakhovetski <lg@denx.de> +# (C) Copyright 2012-2013 Freescale Semiconductor, Inc. +# Copyright (C) 2013, Gateworks Corporation +# +# SPDX-License-Identifier: GPL-2.0+ +# + +obj-y := gw_ventana.o gsc.o + diff --git a/board/gateworks/gw_ventana/README b/board/gateworks/gw_ventana/README new file mode 100644 index 0000000..9e697d6 --- /dev/null +++ b/board/gateworks/gw_ventana/README @@ -0,0 +1,55 @@ +U-Boot for the Gateworks Ventana Product Family boards + +This file contains information for the port of U-Boot to the Gateworks +Ventana Product family boards. + +1. Boot source, boot from NAND +------------------------------ + +The i.MX6 BOOT ROM expects some structures that provide details of NAND layout +and bad block information (referred to as 'bootstreams') which are replicated +multiple times in NAND. The number of replications is configurable through +board strapping options and eFUSE settings. The Freescale 'kobs-ng' +application from the Freescale LTIB BSP, which runs under Linux, must be used +to program the bootstream in order to setup the replicated headers correctly. + +The Gateworks Ventana boards with NAND flash have been factory programmed +such that their eFUSE settings expect 2 copies of the boostream (this is +specified by providing kobs-ng with the --search_exponent=1 argument). Once in +Linux with MTD support for the NAND on /dev/mtd0 you can program the boostream +with: + +kobs-ng init -v -x --search_exponent=1 u-boot.imx + +The kobs-ng application uses an imximage (u-boot.imx) which contains the +Image Vector Table (IVT) and Device Configuration Data (DCD) structures that +the i.MX6 BOOT ROM requires to boot. The kobs-ng adds the Firmware +Configuration Block (FCB) and Discovered Bad Block Table (DBBT). + +This information is taken from: + http://trac.gateworks.com/wiki/ventana/bootloader#NANDFLASH + +More details about the i.MX6 BOOT ROM can be found in the IMX6 reference manual. + +2. Build +-------- + +There are several Gateworks Ventana boards that share a simliar design but +vary based on CPU, Memory configuration, and subloaded devices. Although +the subloaded devices are handled dynamically in the bootloader using +factory configured EEPROM data to modify the device-tree, the CPU choice +(IMX6Q vs IMX6DL) and memory configurations are currently compile-time +options. + +The following Gateworks Ventana configurations exist: + gwventanaq1gspi: MX6Q,1GB,SPI FLASH + gwventanaq : MX6Q,512MB,NAND FLASH + gwventanaq1g : MX6Q,1GB,NAND FLASH + gwventanadl : MX6DL,512MB,NAND FLASH + gwventanadl1g : MX6DL,1GB,NAND FLASH + +To build U-Boot for the MX6Q,1GB,NAND FLASH for example: + + make gwventanaq1g_config + make + diff --git a/board/gateworks/gw_ventana/clocks.cfg b/board/gateworks/gw_ventana/clocks.cfg new file mode 100644 index 0000000..a8118a2 --- /dev/null +++ b/board/gateworks/gw_ventana/clocks.cfg @@ -0,0 +1,42 @@ +/* + * Copyright (C) 2013 Boundary Devices + * Copyright (C) 2013 Gateworks Corporation + * + * SPDX-License-Identifier: GPL-2.0+ + * + * Device Configuration Data (DCD) + * + * Each entry must have the format: + * Addr-type Address Value + * + * where: + * Addr-type register length (1,2 or 4 bytes) + * Address absolute address of the register + * value value to be stored in the register + */ + +/* set the default clock gate to save power */ +DATA 4, CCM_CCGR0, 0x00C03F3F +DATA 4, CCM_CCGR1, 0x0030FC03 +DATA 4, CCM_CCGR2, 0x0FFFC000 +DATA 4, CCM_CCGR3, 0x3FF00000 +DATA 4, CCM_CCGR4, 0xFFFFF300 /* enable NAND/GPMI/BCH clocks */ +DATA 4, CCM_CCGR5, 0x0F0000C3 +DATA 4, CCM_CCGR6, 0x000003FF + +/* enable AXI cache for VDOA/VPU/IPU */ +DATA 4, MX6_IOMUXC_GPR4, 0xF00000CF +/* set IPU AXI-id0 Qos=0xf(bypass) AXI-id1 Qos=0x7 */ +DATA 4, MX6_IOMUXC_GPR6, 0x007F007F +DATA 4, MX6_IOMUXC_GPR7, 0x007F007F + +/* + * Setup CCM_CCOSR register as follows: + * + * cko1_en = 1 --> CKO1 enabled + * cko1_div = 111 --> divide by 8 + * cko1_sel = 1011 --> ahb_clk_root + * + * This sets CKO1 at ahb_clk_root/8 = 132/8 = 16.5 MHz + */ +DATA 4, CCM_CCOSR, 0x000000fb diff --git a/board/gateworks/gw_ventana/gsc.c b/board/gateworks/gw_ventana/gsc.c new file mode 100644 index 0000000..37966ab --- /dev/null +++ b/board/gateworks/gw_ventana/gsc.c @@ -0,0 +1,129 @@ +/* + * Copyright (C) 2013 Gateworks Corporation + * + * Author: Tim Harvey <tharvey@gateworks.com> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <asm/errno.h> +#include <common.h> +#include <i2c.h> +#include <linux/ctype.h> + +#include "gsc.h" + +#define MINMAX(n, percent) ((n)*(100-percent)/100), ((n)*(100+percent)/100) + +/* + * The Gateworks System Controller will fail to ACK a master transaction if + * it is busy, which can occur during its 1HZ timer tick while reading ADC's. + * When this does occur, it will never be busy long enough to fail more than + * 2 back-to-back transfers. Thus we wrap i2c_read and i2c_write with + * 3 retries. + */ +int gsc_i2c_read(uchar chip, uint addr, int alen, uchar *buf, int len) +{ + int retry = 3; + int n = 0; + int ret; + + while (n++ < retry) { + ret = i2c_read(chip, addr, alen, buf, len); + if (!ret) + break; + debug("%s: 0x%02x 0x%02x retry%d: %d\n", __func__, chip, addr, + n, ret); + if (ret != -ENODEV) + break; + mdelay(10); + } + return ret; +} + +int gsc_i2c_write(uchar chip, uint addr, int alen, uchar *buf, int len) +{ + int retry = 3; + int n = 0; + int ret; + + while (n++ < retry) { + ret = i2c_write(chip, addr, alen, buf, len); + if (!ret) + break; + debug("%s: 0x%02x 0x%02x retry%d: %d\n", __func__, chip, addr, + n, ret); + if (ret != -ENODEV) + break; + mdelay(10); + } + mdelay(1); + return ret; +} + +#ifdef CONFIG_CMD_GSC +static void read_hwmon(const char *name, uint reg, uint size, uint low, + uint high) +{ + unsigned char buf[3]; + uint ui; + + printf("%-8s:", name); + memset(buf, 0, sizeof(buf)); + if (gsc_i2c_read(GSC_HWMON_ADDR, reg, 1, buf, size)) { + puts("fRD\n"); + } else { + ui = buf[0] | (buf[1]<<8) | (buf[2]<<16); + if (ui == 0xffffff) + printf("invalid"); + else if (ui < low) + printf("%d Failed - Low", ui); + else if (ui > high) + printf("%d Failed - High", ui); + else + printf("%d", ui); + } + puts("\n"); +} + +int do_gsc(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) +{ + const char *model = getenv("model"); + + i2c_set_bus_num(0); + read_hwmon("Temp", GSC_HWMON_TEMP, 2, 0, 9000); + read_hwmon("VIN", GSC_HWMON_VIN, 3, 8000, 60000); + read_hwmon("VBATT", GSC_HWMON_VBATT, 3, 1800, 3500); + read_hwmon("VDD_3P3", GSC_HWMON_VDD_3P3, 3, MINMAX(3300, 10)); + read_hwmon("VDD_HIGH", GSC_HWMON_VDD_HIGH, 3, MINMAX(3000, 10)); + read_hwmon("VDD_DDR", GSC_HWMON_VDD_DDR, 3, MINMAX(1500, 10)); + read_hwmon("VDD_5P0", GSC_HWMON_VDD_5P0, 3, MINMAX(5000, 10)); + read_hwmon("VDD_2P5", GSC_HWMON_VDD_2P5, 3, MINMAX(2500, 10)); + read_hwmon("VDD_1P8", GSC_HWMON_VDD_1P8, 3, MINMAX(1800, 10)); + + switch (model[3]) { + case '1': /* GW51xx */ + read_hwmon("VDD_CORE", GSC_HWMON_VDD_CORE, 3, MINMAX(1175, 10)); + read_hwmon("VDD_SOC", GSC_HWMON_VDD_SOC, 3, MINMAX(1175, 10)); + break; + case '2': /* GW52xx */ + case '3': /* GW53xx */ + read_hwmon("VDD_CORE", GSC_HWMON_VDD_CORE, 3, MINMAX(1175, 10)); + read_hwmon("VDD_SOC", GSC_HWMON_VDD_SOC, 3, MINMAX(1175, 10)); + read_hwmon("VDD_1P0", GSC_HWMON_VDD_1P0, 3, MINMAX(1000, 10)); + break; + case '4': /* GW54xx */ + read_hwmon("VDD_CORE", GSC_HWMON_VDD_CORE, 3, MINMAX(1375, 10)); + read_hwmon("VDD_SOC", GSC_HWMON_VDD_SOC, 3, MINMAX(1375, 10)); + read_hwmon("VDD_1P0", GSC_HWMON_VDD_1P0, 3, MINMAX(1000, 10)); + break; + } + return 0; +} + +U_BOOT_CMD(gsc, 1, 1, do_gsc, + "GSC test", + "" +); + +#endif /* CONFIG_CMD_GSC */ diff --git a/board/gateworks/gw_ventana/gsc.h b/board/gateworks/gw_ventana/gsc.h new file mode 100644 index 0000000..da970c3 --- /dev/null +++ b/board/gateworks/gw_ventana/gsc.h @@ -0,0 +1,64 @@ +/* + * Copyright (C) 2013 Gateworks Corporation + * + * Author: Tim Harvey <tharvey@gateworks.com> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __ASSEMBLY__ + +/* i2c slave addresses */ +#define GSC_SC_ADDR 0x20 +#define GSC_RTC_ADDR 0x68 +#define GSC_HWMON_ADDR 0x29 +#define GSC_EEPROM_ADDR 0x51 + +/* System Controller registers */ +enum { + GSC_SC_CTRL0 = 0x00, + GSC_SC_CTRL1 = 0x01, + GSC_SC_STATUS = 0x0a, + GSC_SC_FWVER = 0x0e, +}; + +/* System Controller Control1 bits */ +enum { + GSC_SC_CTRL1_WDDIS = 7, /* 1 = disable watchdog */ +}; + +/* System Controller Interrupt bits */ +enum { + GSC_SC_IRQ_PB = 0, /* Pushbutton switch */ + GSC_SC_IRQ_SECURE = 1, /* Secure Key erase operation complete */ + GSC_SC_IRQ_EEPROM_WP = 2, /* EEPROM write violation */ + GSC_SC_IRQ_GPIO = 4, /* GPIO change */ + GSC_SC_IRQ_TAMPER = 5, /* Tamper detect */ + GSC_SC_IRQ_WATCHDOG = 6, /* Watchdog trip */ + GSC_SC_IRQ_PBLONG = 7, /* Pushbutton long hold */ +}; + +/* Hardware Monitor registers */ +enum { + GSC_HWMON_TEMP = 0x00, + GSC_HWMON_VIN = 0x02, + GSC_HWMON_VDD_3P3 = 0x05, + GSC_HWMON_VBATT = 0x08, + GSC_HWMON_VDD_5P0 = 0x0b, + GSC_HWMON_VDD_CORE = 0x0e, + GSC_HWMON_VDD_HIGH = 0x14, + GSC_HWMON_VDD_DDR = 0x17, + GSC_HWMON_VDD_SOC = 0x11, + GSC_HWMON_VDD_1P8 = 0x1d, + GSC_HWMON_VDD_2P5 = 0x23, + GSC_HWMON_VDD_1P0 = 0x20, +}; + +/* + * I2C transactions to the GSC are done via these functions which + * perform retries in the case of a busy GSC NAK'ing the transaction + */ +int gsc_i2c_read(uchar chip, uint addr, int alen, uchar *buf, int len); +int gsc_i2c_write(uchar chip, uint addr, int alen, uchar *buf, int len); +#endif + diff --git a/board/gateworks/gw_ventana/gw_ventana.c b/board/gateworks/gw_ventana/gw_ventana.c new file mode 100644 index 0000000..c130e2c --- /dev/null +++ b/board/gateworks/gw_ventana/gw_ventana.c @@ -0,0 +1,1263 @@ +/* + * Copyright (C) 2013 Gateworks Corporation + * + * Author: Tim Harvey <tharvey@gateworks.com> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <asm/io.h> +#include <asm/arch/clock.h> +#include <asm/arch/imx-regs.h> +#include <asm/arch/iomux.h> +#include <asm/arch/mx6-pins.h> +#include <asm/arch/crm_regs.h> +#include <asm/arch/sys_proto.h> +#include <asm/gpio.h> +#include <asm/imx-common/iomux-v3.h> +#include <asm/imx-common/mxc_i2c.h> +#include <asm/imx-common/boot_mode.h> +#include <asm/imx-common/sata.h> +#include <jffs2/load_kernel.h> +#include <hwconfig.h> +#include <i2c.h> +#include <linux/ctype.h> +#include <fdt_support.h> +#include <fsl_esdhc.h> +#include <miiphy.h> +#include <mmc.h> +#include <mtd_node.h> +#include <netdev.h> +#include <power/pmic.h> +#include <power/pfuze100_pmic.h> +#include <i2c.h> +#include <fdt_support.h> +#include <jffs2/load_kernel.h> +#include <spi_flash.h> + +#include "gsc.h" +#include "ventana_eeprom.h" + +DECLARE_GLOBAL_DATA_PTR; + +/* GPIO's common to all baseboards */ +#define GP_PHY_RST IMX_GPIO_NR(1, 30) +#define GP_USB_OTG_PWR IMX_GPIO_NR(3, 22) +#define GP_SD3_CD IMX_GPIO_NR(7, 0) +#define GP_RS232_EN IMX_GPIO_NR(2, 11) +#define GP_MSATA_SEL IMX_GPIO_NR(2, 8) + +/* I2C bus numbers */ +#define I2C_GSC 0 +#define I2C_PMIC 1 + +#define UART_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \ + PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \ + PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS) + +#define USDHC_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \ + PAD_CTL_PUS_47K_UP | PAD_CTL_SPEED_LOW | \ + PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS) + +#define ENET_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \ + PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \ + PAD_CTL_DSE_40ohm | PAD_CTL_HYS) + +#define SPI_PAD_CTRL (PAD_CTL_HYS | \ + PAD_CTL_PUS_100K_DOWN | PAD_CTL_SPEED_MED | \ + PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST) + +#define DIO_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \ + PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \ + PAD_CTL_DSE_34ohm | PAD_CTL_HYS | PAD_CTL_SRE_FAST) + +#define I2C_PAD_CTRL (PAD_CTL_PUS_100K_UP | \ + PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \ + PAD_CTL_ODE | PAD_CTL_SRE_FAST) + +/* + * EEPROM board info struct populated by read_eeprom so that we only have to + * read it once. + */ +static struct ventana_board_info ventana_info; + +enum { + GW54proto, /* original GW5400-A prototype */ + GW51xx, + GW52xx, + GW53xx, + GW54xx, + GW_UNKNOWN, +}; + +int board_type; + +/* UART1: Function varies per baseboard */ +iomux_v3_cfg_t const uart1_pads[] = { + MX6_PAD_SD3_DAT6__UART1_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL), + MX6_PAD_SD3_DAT7__UART1_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL), +}; + +/* UART2: Serial Console */ +iomux_v3_cfg_t const uart2_pads[] = { + MX6_PAD_SD4_DAT7__UART2_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL), + MX6_PAD_SD4_DAT4__UART2_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL), +}; + +#define PC MUX_PAD_CTRL(I2C_PAD_CTRL) + +/* I2C1: GSC */ +struct i2c_pads_info i2c_pad_info0 = { + .scl = { + .i2c_mode = MX6_PAD_EIM_D21__I2C1_SCL | PC, + .gpio_mode = MX6_PAD_EIM_D21__GPIO3_IO21 | PC, + .gp = IMX_GPIO_NR(3, 21) + }, + .sda = { + .i2c_mode = MX6_PAD_EIM_D28__I2C1_SDA | PC, + .gpio_mode = MX6_PAD_EIM_D28__GPIO3_IO28 | PC, + .gp = IMX_GPIO_NR(3, 28) + } +}; + +/* I2C2: PMIC/PCIe Switch/PCIe Clock/Mezz */ +struct i2c_pads_info i2c_pad_info1 = { + .scl = { + .i2c_mode = MX6_PAD_KEY_COL3__I2C2_SCL | PC, + .gpio_mode = MX6_PAD_KEY_COL3__GPIO4_IO12 | PC, + .gp = IMX_GPIO_NR(4, 12) + }, + .sda = { + .i2c_mode = MX6_PAD_KEY_ROW3__I2C2_SDA | PC, + .gpio_mode = MX6_PAD_KEY_ROW3__GPIO4_IO13 | PC, + .gp = IMX_GPIO_NR(4, 13) + } +}; + +/* I2C3: Misc/Expansion */ +struct i2c_pads_info i2c_pad_info2 = { + .scl = { + .i2c_mode = MX6_PAD_GPIO_3__I2C3_SCL | PC, + .gpio_mode = MX6_PAD_GPIO_3__GPIO1_IO03 | PC, + .gp = IMX_GPIO_NR(1, 3) + }, + .sda = { + .i2c_mode = MX6_PAD_GPIO_6__I2C3_SDA | PC, + .gpio_mode = MX6_PAD_GPIO_6__GPIO1_IO06 | PC, + .gp = IMX_GPIO_NR(1, 6) + } +}; + +/* MMC */ +iomux_v3_cfg_t const usdhc3_pads[] = { + MX6_PAD_SD3_CLK__SD3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD3_CMD__SD3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD3_DAT0__SD3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD3_DAT1__SD3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD3_DAT2__SD3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD3_DAT3__SD3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD3_DAT5__GPIO7_IO00 | MUX_PAD_CTRL(NO_PAD_CTRL), /* CD */ +}; + +/* ENET */ +iomux_v3_cfg_t const enet_pads[] = { + MX6_PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6_PAD_ENET_MDC__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6_PAD_RGMII_TXC__RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6_PAD_RGMII_TD0__RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6_PAD_RGMII_TD1__RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6_PAD_RGMII_TD2__RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6_PAD_RGMII_TD3__RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6_PAD_RGMII_TX_CTL__RGMII_TX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6_PAD_ENET_REF_CLK__ENET_TX_CLK | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6_PAD_RGMII_RXC__RGMII_RXC | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6_PAD_RGMII_RD0__RGMII_RD0 | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6_PAD_RGMII_RD1__RGMII_RD1 | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6_PAD_RGMII_RD2__RGMII_RD2 | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6_PAD_RGMII_RD3__RGMII_RD3 | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6_PAD_RGMII_RX_CTL__RGMII_RX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL), + /* PHY nRST */ + MX6_PAD_ENET_TXD0__GPIO1_IO30 | MUX_PAD_CTRL(NO_PAD_CTRL), +}; + +/* NAND */ +iomux_v3_cfg_t const nfc_pads[] = { + MX6_PAD_NANDF_CLE__NAND_CLE | MUX_PAD_CTRL(NO_PAD_CTRL), + MX6_PAD_NANDF_ALE__NAND_ALE | MUX_PAD_CTRL(NO_PAD_CTRL), + MX6_PAD_NANDF_WP_B__NAND_WP_B | MUX_PAD_CTRL(NO_PAD_CTRL), + MX6_PAD_NANDF_RB0__NAND_READY_B | MUX_PAD_CTRL(NO_PAD_CTRL), + MX6_PAD_NANDF_CS0__NAND_CE0_B | MUX_PAD_CTRL(NO_PAD_CTRL), + MX6_PAD_SD4_CMD__NAND_RE_B | MUX_PAD_CTRL(NO_PAD_CTRL), + MX6_PAD_SD4_CLK__NAND_WE_B | MUX_PAD_CTRL(NO_PAD_CTRL), + MX6_PAD_NANDF_D0__NAND_DATA00 | MUX_PAD_CTRL(NO_PAD_CTRL), + MX6_PAD_NANDF_D1__NAND_DATA01 | MUX_PAD_CTRL(NO_PAD_CTRL), + MX6_PAD_NANDF_D2__NAND_DATA02 | MUX_PAD_CTRL(NO_PAD_CTRL), + MX6_PAD_NANDF_D3__NAND_DATA03 | MUX_PAD_CTRL(NO_PAD_CTRL), + MX6_PAD_NANDF_D4__NAND_DATA04 | MUX_PAD_CTRL(NO_PAD_CTRL), + MX6_PAD_NANDF_D5__NAND_DATA05 | MUX_PAD_CTRL(NO_PAD_CTRL), + MX6_PAD_NANDF_D6__NAND_DATA06 | MUX_PAD_CTRL(NO_PAD_CTRL), + MX6_PAD_NANDF_D7__NAND_DATA07 | MUX_PAD_CTRL(NO_PAD_CTRL), +}; + +#ifdef CONFIG_CMD_NAND +static void setup_gpmi_nand(void) +{ + struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR; + + /* config gpmi nand iomux */ + imx_iomux_v3_setup_multiple_pads(nfc_pads, ARRAY_SIZE(nfc_pads)); + + /* config gpmi and bch clock to 100 MHz */ + clrsetbits_le32(&mxc_ccm->cs2cdr, + MXC_CCM_CS2CDR_ENFC_CLK_PODF_MASK | + MXC_CCM_CS2CDR_ENFC_CLK_PRED_MASK | + MXC_CCM_CS2CDR_ENFC_CLK_SEL_MASK, + MXC_CCM_CS2CDR_ENFC_CLK_PODF(0) | + MXC_CCM_CS2CDR_ENFC_CLK_PRED(3) | + MXC_CCM_CS2CDR_ENFC_CLK_SEL(3)); + + /* enable gpmi and bch clock gating */ + setbits_le32(&mxc_ccm->CCGR4, + MXC_CCM_CCGR4_RAWNAND_U_BCH_INPUT_APB_MASK | + MXC_CCM_CCGR4_RAWNAND_U_GPMI_BCH_INPUT_BCH_MASK | + MXC_CCM_CCGR4_RAWNAND_U_GPMI_BCH_INPUT_GPMI_IO_MASK | + MXC_CCM_CCGR4_RAWNAND_U_GPMI_INPUT_APB_MASK | + MXC_CCM_CCGR4_PL301_MX6QPER1_BCH_OFFSET); + + /* enable apbh clock gating */ + setbits_le32(&mxc_ccm->CCGR0, MXC_CCM_CCGR0_APBHDMA_MASK); +} +#endif + +static void setup_iomux_enet(void) +{ + imx_iomux_v3_setup_multiple_pads(enet_pads, ARRAY_SIZE(enet_pads)); + + /* toggle PHY_RST# */ + gpio_direction_output(GP_PHY_RST, 0); + mdelay(2); + gpio_set_value(GP_PHY_RST, 1); +} + +static void setup_iomux_uart(void) +{ + imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads)); + imx_iomux_v3_setup_multiple_pads(uart2_pads, ARRAY_SIZE(uart2_pads)); +} + +#ifdef CONFIG_USB_EHCI_MX6 +iomux_v3_cfg_t const usb_pads[] = { + MX6_PAD_GPIO_1__USB_OTG_ID | MUX_PAD_CTRL(DIO_PAD_CTRL), + MX6_PAD_KEY_COL4__USB_OTG_OC | MUX_PAD_CTRL(DIO_PAD_CTRL), + MX6_PAD_EIM_D22__GPIO3_IO22 | MUX_PAD_CTRL(DIO_PAD_CTRL), /* OTG PWR */ +}; + +int board_ehci_hcd_init(int port) +{ + struct ventana_board_info *info = &ventana_info; + + imx_iomux_v3_setup_multiple_pads(usb_pads, ARRAY_SIZE(usb_pads)); + + /* Reset USB HUB (present on GW54xx/GW53xx) */ + switch (info->model[3]) { + case '3': /* GW53xx */ + imx_iomux_v3_setup_pad(MX6_PAD_GPIO_9__GPIO1_IO09| + MUX_PAD_CTRL(NO_PAD_CTRL)); + gpio_direction_output(IMX_GPIO_NR(1, 9), 0); + mdelay(2); + gpio_set_value(IMX_GPIO_NR(1, 9), 1); + break; + case '4': /* GW54xx */ + imx_iomux_v3_setup_pad(MX6_PAD_SD1_DAT0__GPIO1_IO16 | + MUX_PAD_CTRL(NO_PAD_CTRL)); + gpio_direction_output(IMX_GPIO_NR(1, 16), 0); + mdelay(2); + gpio_set_value(IMX_GPIO_NR(1, 16), 1); + break; + } + + return 0; +} + +int board_ehci_power(int port, int on) +{ + if (port) + return 0; + gpio_set_value(GP_USB_OTG_PWR, on); + return 0; +} +#endif /* CONFIG_USB_EHCI_MX6 */ + +#ifdef CONFIG_FSL_ESDHC +struct fsl_esdhc_cfg usdhc_cfg = { USDHC3_BASE_ADDR }; + +int board_mmc_getcd(struct mmc *mmc) +{ + /* Card Detect */ + gpio_direction_input(GP_SD3_CD); + return !gpio_get_value(GP_SD3_CD); +} + +int board_mmc_init(bd_t *bis) +{ + /* Only one USDHC controller on Ventana */ + imx_iomux_v3_setup_multiple_pads(usdhc3_pads, ARRAY_SIZE(usdhc3_pads)); + usdhc_cfg.sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK); + usdhc_cfg.max_bus_width = 4; + + return fsl_esdhc_initialize(bis, &usdhc_cfg); +} +#endif /* CONFIG_FSL_ESDHC */ + +#ifdef CONFIG_MXC_SPI +iomux_v3_cfg_t const ecspi1_pads[] = { + /* SS1 */ + MX6_PAD_EIM_D19__GPIO3_IO19 | MUX_PAD_CTRL(SPI_PAD_CTRL), + MX6_PAD_EIM_D17__ECSPI1_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL), + MX6_PAD_EIM_D18__ECSPI1_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL), + MX6_PAD_EIM_D16__ECSPI1_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL), +}; + +static void setup_spi(void) +{ + gpio_direction_output(CONFIG_SF_DEFAULT_CS, 1); + imx_iomux_v3_setup_multiple_pads(ecspi1_pads, + ARRAY_SIZE(ecspi1_pads)); +} +#endif + +/* configure eth0 PHY board-specific LED behavior */ +int board_phy_config(struct phy_device *phydev) +{ + unsigned short val; + + /* Marvel 88E1510 */ + if (phydev->phy_id == 0x1410dd1) { + /* + * Page 3, Register 16: LED[2:0] Function Control Register + * LED[0] (SPD:Amber) R16_3.3:0 to 0111: on-GbE link + * LED[1] (LNK:Green) R16_3.7:4 to 0001: on-link, blink-activity + */ + phy_write(phydev, MDIO_DEVAD_NONE, 22, 3); + val = phy_read(phydev, MDIO_DEVAD_NONE, 16); + val &= 0xff00; + val |= 0x0017; + phy_write(phydev, MDIO_DEVAD_NONE, 16, val); + phy_write(phydev, MDIO_DEVAD_NONE, 22, 0); + } + + if (phydev->drv->config) + phydev->drv->config(phydev); + + return 0; +} + +int board_eth_init(bd_t *bis) +{ + setup_iomux_enet(); + +#ifdef CONFIG_FEC_MXC + cpu_eth_init(bis); +#endif + +#ifdef CONFIG_CI_UDC + /* For otg ethernet*/ + usb_eth_initialize(bis); +#endif + + return 0; +} + +/* read ventana EEPROM, check for validity, and return baseboard type */ +static int +read_eeprom(void) +{ + int i; + int chksum; + char baseboard; + int type; + struct ventana_board_info *info = &ventana_info; + unsigned char *buf = (unsigned char *)&ventana_info; + + memset(info, 0, sizeof(ventana_info)); + + /* + * On a board with a missing/depleted backup battery for GSC, the + * board may be ready to probe the GSC before its firmware is + * running. We will wait here indefinately for the GSC/EEPROM. + */ + while (1) { + if (0 == i2c_set_bus_num(I2C_GSC) && + 0 == i2c_probe(GSC_EEPROM_ADDR)) + break; + mdelay(1); + } + + /* read eeprom config section */ + if (gsc_i2c_read(GSC_EEPROM_ADDR, 0x00, 1, buf, sizeof(ventana_info))) { + puts("EEPROM: Failed to read EEPROM\n"); + info->model[0] = 0; + return GW_UNKNOWN; + } + + /* sanity checks */ + if (info->model[0] != 'G' || info->model[1] != 'W') { + puts("EEPROM: Invalid Model in EEPROM\n"); + info->model[0] = 0; + return GW_UNKNOWN; + } + + /* validate checksum */ + for (chksum = 0, i = 0; i < sizeof(*info)-2; i++) + chksum += buf[i]; + if ((info->chksum[0] != chksum>>8) || + (info->chksum[1] != (chksum&0xff))) { + puts("EEPROM: Failed EEPROM checksum\n"); + info->model[0] = 0; + return GW_UNKNOWN; + } + + /* original GW5400-A prototype */ + baseboard = info->model[3]; + if (strncasecmp((const char *)info->model, "GW5400-A", 8) == 0) + baseboard = '0'; + + switch (baseboard) { + case '0': /* original GW5400-A prototype */ + type = GW54proto; + break; + case '1': + type = GW51xx; + break; + case '2': + type = GW52xx; + break; + case '3': + type = GW53xx; + break; + case '4': + type = GW54xx; + break; + default: + printf("EEPROM: Unknown model in EEPROM: %s\n", info->model); + type = GW_UNKNOWN; + break; + } + return type; +} + +/* + * Baseboard specific GPIO + */ + +/* common to add baseboards */ +static iomux_v3_cfg_t const gw_gpio_pads[] = { + /* MSATA_EN */ + MX6_PAD_SD4_DAT0__GPIO2_IO08 | MUX_PAD_CTRL(NO_PAD_CTRL), + /* RS232_EN# */ + MX6_PAD_SD4_DAT3__GPIO2_IO11 | MUX_PAD_CTRL(NO_PAD_CTRL), +}; + +/* prototype */ +static iomux_v3_cfg_t const gwproto_gpio_pads[] = { + /* PANLEDG# */ + MX6_PAD_KEY_COL0__GPIO4_IO06 | MUX_PAD_CTRL(NO_PAD_CTRL), + /* PANLEDR# */ + MX6_PAD_KEY_ROW0__GPIO4_IO07 | MUX_PAD_CTRL(NO_PAD_CTRL), + /* LOCLED# */ + MX6_PAD_KEY_ROW4__GPIO4_IO15 | MUX_PAD_CTRL(NO_PAD_CTRL), + /* RS485_EN */ + MX6_PAD_SD3_DAT4__GPIO7_IO01 | MUX_PAD_CTRL(NO_PAD_CTRL), + /* IOEXP_PWREN# */ + MX6_PAD_EIM_A19__GPIO2_IO19 | MUX_PAD_CTRL(NO_PAD_CTRL), + /* IOEXP_IRQ# */ + MX6_PAD_EIM_A20__GPIO2_IO18 | MUX_PAD_CTRL(NO_PAD_CTRL), + /* VID_EN */ + MX6_PAD_EIM_D31__GPIO3_IO31 | MUX_PAD_CTRL(NO_PAD_CTRL), + /* DIOI2C_DIS# */ + MX6_PAD_GPIO_19__GPIO4_IO05 | MUX_PAD_CTRL(NO_PAD_CTRL), + /* PCICK_SSON */ + MX6_PAD_SD1_CLK__GPIO1_IO20 | MUX_PAD_CTRL(NO_PAD_CTRL), + /* PCI_RST# */ + MX6_PAD_ENET_TXD1__GPIO1_IO29 | MUX_PAD_CTRL(NO_PAD_CTRL), +}; + +static iomux_v3_cfg_t const gw51xx_gpio_pads[] = { + /* PANLEDG# */ + MX6_PAD_KEY_COL0__GPIO4_IO06 | MUX_PAD_CTRL(NO_PAD_CTRL), + /* PANLEDR# */ + MX6_PAD_KEY_ROW0__GPIO4_IO07 | MUX_PAD_CTRL(NO_PAD_CTRL), + /* IOEXP_PWREN# */ + MX6_PAD_EIM_A19__GPIO2_IO19 | MUX_PAD_CTRL(NO_PAD_CTRL), + /* IOEXP_IRQ# */ + MX6_PAD_EIM_A20__GPIO2_IO18 | MUX_PAD_CTRL(NO_PAD_CTRL), + + /* GPS_SHDN */ + MX6_PAD_GPIO_2__GPIO1_IO02 | MUX_PAD_CTRL(NO_PAD_CTRL), + /* VID_PWR */ + MX6_PAD_CSI0_DATA_EN__GPIO5_IO20 | MUX_PAD_CTRL(NO_PAD_CTRL), + /* PCI_RST# */ + MX6_PAD_GPIO_0__GPIO1_IO00 | MUX_PAD_CTRL(NO_PAD_CTRL), +}; + +static iomux_v3_cfg_t const gw52xx_gpio_pads[] = { + /* PANLEDG# */ + MX6_PAD_KEY_COL0__GPIO4_IO06 | MUX_PAD_CTRL(NO_PAD_CTRL), + /* PANLEDR# */ + MX6_PAD_KEY_ROW0__GPIO4_IO07 | MUX_PAD_CTRL(NO_PAD_CTRL), + /* IOEXP_PWREN# */ + MX6_PAD_EIM_A19__GPIO2_IO19 | MUX_PAD_CTRL(NO_PAD_CTRL), + /* IOEXP_IRQ# */ + MX6_PAD_EIM_A20__GPIO2_IO18 | MUX_PAD_CTRL(NO_PAD_CTRL), + + /* MX6_LOCLED# */ + MX6_PAD_KEY_ROW4__GPIO4_IO15 | MUX_PAD_CTRL(NO_PAD_CTRL), + /* GPS_SHDN */ + MX6_PAD_ENET_RXD0__GPIO1_IO27 | MUX_PAD_CTRL(NO_PAD_CTRL), + /* USBOTG_SEL */ + MX6_PAD_GPIO_2__GPIO1_IO02 | MUX_PAD_CTRL(NO_PAD_CTRL), + /* VID_PWR */ + MX6_PAD_EIM_D31__GPIO3_IO31 | MUX_PAD_CTRL(NO_PAD_CTRL), + /* PCI_RST# */ + MX6_PAD_ENET_TXD1__GPIO1_IO29 | MUX_PAD_CTRL(NO_PAD_CTRL), +}; + +static iomux_v3_cfg_t const gw53xx_gpio_pads[] = { + /* PANLEDG# */ + MX6_PAD_KEY_COL0__GPIO4_IO06 | MUX_PAD_CTRL(NO_PAD_CTRL), + /* PANLEDR# */ + MX6_PAD_KEY_ROW0__GPIO4_IO07 | MUX_PAD_CTRL(NO_PAD_CTRL), + /* IOEXP_PWREN# */ + MX6_PAD_EIM_A19__GPIO2_IO19 | MUX_PAD_CTRL(NO_PAD_CTRL), + /* IOEXP_IRQ# */ + MX6_PAD_EIM_A20__GPIO2_IO18 | MUX_PAD_CTRL(NO_PAD_CTRL), + + /* MX6_LOCLED# */ + MX6_PAD_KEY_ROW4__GPIO4_IO15 | MUX_PAD_CTRL(NO_PAD_CTRL), + /* GPS_SHDN */ + MX6_PAD_ENET_RXD0__GPIO1_IO27 | MUX_PAD_CTRL(NO_PAD_CTRL), + /* VID_EN */ + MX6_PAD_EIM_D31__GPIO3_IO31 | MUX_PAD_CTRL(NO_PAD_CTRL), + /* PCI_RST# */ + MX6_PAD_ENET_TXD1__GPIO1_IO29 | MUX_PAD_CTRL(NO_PAD_CTRL), +}; + +static iomux_v3_cfg_t const gw54xx_gpio_pads[] = { + /* PANLEDG# */ + MX6_PAD_KEY_COL0__GPIO4_IO06 | MUX_PAD_CTRL(NO_PAD_CTRL), + /* PANLEDR# */ + MX6_PAD_KEY_COL2__GPIO4_IO10 | MUX_PAD_CTRL(NO_PAD_CTRL), + /* MX6_LOCLED# */ + MX6_PAD_KEY_ROW4__GPIO4_IO15 | MUX_PAD_CTRL(NO_PAD_CTRL), + /* MIPI_DIO */ + MX6_PAD_SD1_DAT3__GPIO1_IO21 | MUX_PAD_CTRL(NO_PAD_CTRL), + /* RS485_EN */ + MX6_PAD_EIM_D24__GPIO3_IO24 | MUX_PAD_CTRL(NO_PAD_CTRL), + /* IOEXP_PWREN# */ + MX6_PAD_KEY_ROW0__GPIO4_IO07 | MUX_PAD_CTRL(NO_PAD_CTRL), + /* IOEXP_IRQ# */ + MX6_PAD_KEY_ROW1__GPIO4_IO09 | MUX_PAD_CTRL(NO_PAD_CTRL), + /* DIOI2C_DIS# */ + MX6_PAD_GPIO_19__GPIO4_IO05 | MUX_PAD_CTRL(NO_PAD_CTRL), + /* DIOI2C_DIS# */ + MX6_PAD_GPIO_19__GPIO4_IO05 | MUX_PAD_CTRL(NO_PAD_CTRL), + /* PCICK_SSON */ + MX6_PAD_SD1_CLK__GPIO1_IO20 | MUX_PAD_CTRL(NO_PAD_CTRL), + /* PCI_RST# */ + MX6_PAD_ENET_TXD1__GPIO1_IO29 | MUX_PAD_CTRL(NO_PAD_CTRL), +}; + +/* + * each baseboard has 4 user configurable Digital IO lines which can + * be pinmuxed as a GPIO or in some cases a PWM + */ +struct dio_cfg { + iomux_v3_cfg_t gpio_padmux; + unsigned gpio_param; + iomux_v3_cfg_t pwm_padmux; + unsigned pwm_param; +}; + +struct ventana { + /* pinmux */ + iomux_v3_cfg_t const *gpio_pads; + int num_pads; + /* DIO pinmux/val */ + struct dio_cfg dio_cfg[4]; + /* various gpios (0 if non-existent) */ + int leds[3]; + int pcie_rst; + int mezz_pwren; + int mezz_irq; + int rs485en; + int gps_shdn; + int vidin_en; + int dioi2c_en; + int pcie_sson; + int usb_sel; +}; + +struct ventana gpio_cfg[] = { + /* GW5400proto */ + { + .gpio_pads = gw54xx_gpio_pads, + .num_pads = ARRAY_SIZE(gw54xx_gpio_pads), + .dio_cfg = { + { MX6_PAD_GPIO_9__GPIO1_IO09, IMX_GPIO_NR(1, 9), + MX6_PAD_GPIO_9__PWM1_OUT, 1 }, + { MX6_PAD_SD1_DAT2__GPIO1_IO19, IMX_GPIO_NR(1, 19), + MX6_PAD_SD1_DAT2__PWM2_OUT, 2 }, + { MX6_PAD_SD4_DAT1__GPIO2_IO09, IMX_GPIO_NR(2, 9), + MX6_PAD_SD4_DAT1__PWM3_OUT, 3 }, + { MX6_PAD_SD4_DAT2__GPIO2_IO10, IMX_GPIO_NR(2, 10), + MX6_PAD_SD4_DAT2__PWM4_OUT, 4 }, + }, + .leds = { + IMX_GPIO_NR(4, 6), + IMX_GPIO_NR(4, 10), + IMX_GPIO_NR(4, 15), + }, + .pcie_rst = IMX_GPIO_NR(1, 29), + .mezz_pwren = IMX_GPIO_NR(4, 7), + .mezz_irq = IMX_GPIO_NR(4, 9), + .rs485en = IMX_GPIO_NR(3, 24), + .dioi2c_en = IMX_GPIO_NR(4, 5), + .pcie_sson = IMX_GPIO_NR(1, 20), + }, + + /* GW51xx */ + { + .gpio_pads = gw51xx_gpio_pads, + .num_pads = ARRAY_SIZE(gw51xx_gpio_pads), + .dio_cfg = { + { MX6_PAD_SD1_DAT0__GPIO1_IO16, IMX_GPIO_NR(1, 16), + 0, 0 }, + { MX6_PAD_SD1_DAT2__GPIO1_IO19, IMX_GPIO_NR(1, 19), + MX6_PAD_SD1_DAT2__PWM2_OUT, 2 }, + { MX6_PAD_SD1_DAT1__GPIO1_IO17, IMX_GPIO_NR(1, 17), + MX6_PAD_SD1_DAT1__PWM3_OUT, 3 }, + { MX6_PAD_SD1_CMD__GPIO1_IO18, IMX_GPIO_NR(1, 18), + MX6_PAD_SD1_CMD__PWM4_OUT, 4 }, + }, + .leds = { + IMX_GPIO_NR(4, 6), + IMX_GPIO_NR(4, 10), + }, + .pcie_rst = IMX_GPIO_NR(1, 0), + .mezz_pwren = IMX_GPIO_NR(2, 19), + .mezz_irq = IMX_GPIO_NR(2, 18), + .gps_shdn = IMX_GPIO_NR(1, 2), + .vidin_en = IMX_GPIO_NR(5, 20), + }, + + /* GW52xx */ + { + .gpio_pads = gw52xx_gpio_pads, + .num_pads = ARRAY_SIZE(gw52xx_gpio_pads), + .dio_cfg = { + { MX6_PAD_SD1_DAT0__GPIO1_IO16, IMX_GPIO_NR(1, 16), + 0, 0 }, + { MX6_PAD_SD1_DAT2__GPIO1_IO19, IMX_GPIO_NR(1, 19), + MX6_PAD_SD1_DAT2__PWM2_OUT, 2 }, + { MX6_PAD_SD1_DAT1__GPIO1_IO17, IMX_GPIO_NR(1, 17), + MX6_PAD_SD1_DAT1__PWM3_OUT, 3 }, + { MX6_PAD_SD1_CLK__GPIO1_IO20, IMX_GPIO_NR(1, 20), + 0, 0 }, + }, + .leds = { + IMX_GPIO_NR(4, 6), + IMX_GPIO_NR(4, 7), + IMX_GPIO_NR(4, 15), + }, + .pcie_rst = IMX_GPIO_NR(1, 29), + .mezz_pwren = IMX_GPIO_NR(2, 19), + .mezz_irq = IMX_GPIO_NR(2, 18), + .gps_shdn = IMX_GPIO_NR(1, 27), + .vidin_en = IMX_GPIO_NR(3, 31), + .usb_sel = IMX_GPIO_NR(1, 2), + }, + + /* GW53xx */ + { + .gpio_pads = gw53xx_gpio_pads, + .num_pads = ARRAY_SIZE(gw53xx_gpio_pads), + .dio_cfg = { + { MX6_PAD_SD1_DAT0__GPIO1_IO16, IMX_GPIO_NR(1, 16), + 0, 0 }, + { MX6_PAD_SD1_DAT2__GPIO1_IO19, IMX_GPIO_NR(1, 19), + MX6_PAD_SD1_DAT2__PWM2_OUT, 2 }, + { MX6_PAD_SD1_DAT1__GPIO1_IO17, IMX_GPIO_NR(1, 17), + MX6_PAD_SD1_DAT1__PWM3_OUT, 3 }, + { MX6_PAD_SD1_CLK__GPIO1_IO20, IMX_GPIO_NR(1, 20), + 0, 0 }, + }, + .leds = { + IMX_GPIO_NR(4, 6), + IMX_GPIO_NR(4, 7), + IMX_GPIO_NR(4, 15), + }, + .pcie_rst = IMX_GPIO_NR(1, 29), + .mezz_pwren = IMX_GPIO_NR(2, 19), + .mezz_irq = IMX_GPIO_NR(2, 18), + .gps_shdn = IMX_GPIO_NR(1, 27), + .vidin_en = IMX_GPIO_NR(3, 31), + }, + + /* GW54xx */ + { + .gpio_pads = gw54xx_gpio_pads, + .num_pads = ARRAY_SIZE(gw54xx_gpio_pads), + .dio_cfg = { + { MX6_PAD_GPIO_9__GPIO1_IO09, IMX_GPIO_NR(1, 9), + MX6_PAD_GPIO_9__PWM1_OUT, 1 }, + { MX6_PAD_SD1_DAT2__GPIO1_IO19, IMX_GPIO_NR(1, 19), + MX6_PAD_SD1_DAT2__PWM2_OUT, 2 }, + { MX6_PAD_SD4_DAT1__GPIO2_IO09, IMX_GPIO_NR(2, 9), + MX6_PAD_SD4_DAT1__PWM3_OUT, 3 }, + { MX6_PAD_SD4_DAT2__GPIO2_IO10, IMX_GPIO_NR(2, 10), + MX6_PAD_SD4_DAT2__PWM4_OUT, 4 }, + }, + .leds = { + IMX_GPIO_NR(4, 6), + IMX_GPIO_NR(4, 7), + IMX_GPIO_NR(4, 15), + }, + .pcie_rst = IMX_GPIO_NR(1, 29), + .mezz_pwren = IMX_GPIO_NR(2, 19), + .mezz_irq = IMX_GPIO_NR(2, 18), + .rs485en = IMX_GPIO_NR(7, 1), + .vidin_en = IMX_GPIO_NR(3, 31), + .dioi2c_en = IMX_GPIO_NR(4, 5), + .pcie_sson = IMX_GPIO_NR(1, 20), + }, +}; + +/* setup GPIO pinmux and default configuration per baseboard */ +static void setup_board_gpio(int board) +{ + struct ventana_board_info *info = &ventana_info; + const char *s; + char arg[10]; + size_t len; + int i; + int quiet = simple_strtol(getenv("quiet"), NULL, 10); + + if (board >= GW_UNKNOWN) + return; + + /* RS232_EN# */ + gpio_direction_output(GP_RS232_EN, (hwconfig("rs232")) ? 0 : 1); + + /* MSATA Enable */ + if (is_cpu_type(MXC_CPU_MX6Q) && + test_bit(EECONFIG_SATA, info->config)) { + gpio_direction_output(GP_MSATA_SEL, + (hwconfig("msata")) ? 1 : 0); + } else { + gpio_direction_output(GP_MSATA_SEL, 0); + } + + /* + * assert PCI_RST# (released by OS when clock is valid) + * TODO: figure out why leaving this de-asserted from PCI scan on boot + * causes linux pcie driver to hang during enumeration + */ + gpio_direction_output(gpio_cfg[board].pcie_rst, 0); + + /* turn off (active-high) user LED's */ + for (i = 0; i < 4; i++) { + if (gpio_cfg[board].leds[i]) + gpio_direction_output(gpio_cfg[board].leds[i], 1); + } + + /* Expansion Mezzanine IO */ + gpio_direction_output(gpio_cfg[board].mezz_pwren, 0); + gpio_direction_input(gpio_cfg[board].mezz_irq); + + /* RS485 Transmit Enable */ + if (gpio_cfg[board].rs485en) + gpio_direction_output(gpio_cfg[board].rs485en, 0); + + /* GPS_SHDN */ + if (gpio_cfg[board].gps_shdn) + gpio_direction_output(gpio_cfg[board].gps_shdn, 1); + + /* Analog video codec power enable */ + if (gpio_cfg[board].vidin_en) + gpio_direction_output(gpio_cfg[board].vidin_en, 1); + + /* DIOI2C_DIS# */ + if (gpio_cfg[board].dioi2c_en) + gpio_direction_output(gpio_cfg[board].dioi2c_en, 0); + + /* PCICK_SSON: disable spread-spectrum clock */ + if (gpio_cfg[board].pcie_sson) + gpio_direction_output(gpio_cfg[board].pcie_sson, 0); + + /* USBOTG Select (PCISKT or FrontPanel) */ + if (gpio_cfg[board].usb_sel) + gpio_direction_output(gpio_cfg[board].usb_sel, 0); + + /* + * Configure DIO pinmux/padctl registers + * see IMX6DQRM/IMX6SDLRM IOMUXC_SW_PAD_CTL_PAD_* register definitions + */ + for (i = 0; i < 4; i++) { + struct dio_cfg *cfg = &gpio_cfg[board].dio_cfg[i]; + unsigned ctrl = DIO_PAD_CTRL; + + sprintf(arg, "dio%d", i); + if (!hwconfig(arg)) + continue; + s = hwconfig_subarg(arg, "padctrl", &len); + if (s) + ctrl = simple_strtoul(s, NULL, 16) & 0x3ffff; + if (hwconfig_subarg_cmp(arg, "mode", "gpio")) { + if (!quiet) { + printf("DIO%d: GPIO%d_IO%02d (gpio-%d)\n", i, + (cfg->gpio_param/32)+1, + cfg->gpio_param%32, + cfg->gpio_param); + } + imx_iomux_v3_setup_pad(cfg->gpio_padmux | + MUX_PAD_CTRL(ctrl)); + gpio_direction_input(cfg->gpio_param); + } else if (hwconfig_subarg_cmp("dio2", "mode", "pwm") && + cfg->pwm_padmux) { + if (!quiet) + printf("DIO%d: pwm%d\n", i, cfg->pwm_param); + imx_iomux_v3_setup_pad(cfg->pwm_padmux | + MUX_PAD_CTRL(ctrl)); + } + } + + if (!quiet) { + if (is_cpu_type(MXC_CPU_MX6Q) && + (test_bit(EECONFIG_SATA, info->config))) { + printf("MSATA: %s\n", (hwconfig("msata") ? + "enabled" : "disabled")); + } + printf("RS232: %s\n", (hwconfig("rs232")) ? + "enabled" : "disabled"); + } +} + +#if defined(CONFIG_CMD_PCI) +int imx6_pcie_toggle_reset(void) +{ + if (board_type < GW_UNKNOWN) { + gpio_direction_output(gpio_cfg[board_type].pcie_rst, 0); + mdelay(50); + gpio_direction_output(gpio_cfg[board_type].pcie_rst, 1); + } + return 0; +} +#endif /* CONFIG_CMD_PCI */ + +#ifdef CONFIG_SERIAL_TAG +/* + * called when setting up ATAGS before booting kernel + * populate serialnum from the following (in order of priority): + * serial# env var + * eeprom + */ +void get_board_serial(struct tag_serialnr *serialnr) +{ + char *serial = getenv("serial#"); + + if (serial) { + serialnr->high = 0; + serialnr->low = simple_strtoul(serial, NULL, 10); + } else if (ventana_info.model[0]) { + serialnr->high = 0; + serialnr->low = ventana_info.serial; + } else { + serialnr->high = 0; + serialnr->low = 0; + } +} +#endif + +/* + * Board Support + */ + +int board_early_init_f(void) +{ + setup_iomux_uart(); + gpio_direction_output(GP_USB_OTG_PWR, 0); /* OTG power off */ + + return 0; +} + +int dram_init(void) +{ + gd->ram_size = get_ram_size((void *)PHYS_SDRAM, + CONFIG_DDR_MB*1024*1024); + + return 0; +} + +int board_init(void) +{ + struct iomuxc_base_regs *const iomuxc_regs + = (struct iomuxc_base_regs *)IOMUXC_BASE_ADDR; + + clrsetbits_le32(&iomuxc_regs->gpr[1], + IOMUXC_GPR1_OTG_ID_MASK, + IOMUXC_GPR1_OTG_ID_GPIO1); + + /* address of linux boot parameters */ + gd->bd->bi_boot_params = PHYS_SDRAM + 0x100; + +#ifdef CONFIG_CMD_NAND + setup_gpmi_nand(); +#endif +#ifdef CONFIG_MXC_SPI + setup_spi(); +#endif + setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info0); + setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1); + setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info2); + +#ifdef CONFIG_CMD_SATA + setup_sata(); +#endif + /* read Gateworks EEPROM into global struct (used later) */ + board_type = read_eeprom(); + + /* board-specifc GPIO iomux */ + if (board_type < GW_UNKNOWN) { + imx_iomux_v3_setup_multiple_pads(gw_gpio_pads, + ARRAY_SIZE(gw_gpio_pads)); + imx_iomux_v3_setup_multiple_pads(gpio_cfg[board_type].gpio_pads, + gpio_cfg[board_type].num_pads); + } + + return 0; +} + +#if defined(CONFIG_DISPLAY_BOARDINFO_LATE) +/* + * called during late init (after relocation and after board_init()) + * by virtue of CONFIG_DISPLAY_BOARDINFO_LATE as we needed i2c initialized and + * EEPROM read. + */ +int checkboard(void) +{ + struct ventana_board_info *info = &ventana_info; + unsigned char buf[4]; + const char *p; + int quiet; /* Quiet or minimal output mode */ + + quiet = 0; + p = getenv("quiet"); + if (p) + quiet = simple_strtol(p, NULL, 10); + else + setenv("quiet", "0"); + + puts("\nGateworks Corporation Copyright 2014\n"); + if (info->model[0]) { + printf("Model: %s\n", info->model); + printf("MFGDate: %02x-%02x-%02x%02x\n", + info->mfgdate[0], info->mfgdate[1], + info->mfgdate[2], info->mfgdate[3]); + printf("Serial:%d\n", info->serial); + } else { + puts("Invalid EEPROM - board will not function fully\n"); + } + if (quiet) + return 0; + + /* Display GSC firmware revision/CRC/status */ + i2c_set_bus_num(I2C_GSC); + if (!gsc_i2c_read(GSC_SC_ADDR, GSC_SC_FWVER, 1, buf, 1)) { + printf("GSC: v%d", buf[0]); + if (!gsc_i2c_read(GSC_SC_ADDR, GSC_SC_STATUS, 1, buf, 4)) { + printf(" 0x%04x", buf[2] | buf[3]<<8); /* CRC */ + printf(" 0x%02x", buf[0]); /* irq status */ + } + puts("\n"); + } + /* Display RTC */ + if (!gsc_i2c_read(GSC_RTC_ADDR, 0x00, 1, buf, 4)) { + printf("RTC: %d\n", + buf[0] | buf[1]<<8 | buf[2]<<16 | buf[3]<<24); + } + + return 0; +} +#endif + +#ifdef CONFIG_CMD_BMODE +/* + * BOOT_CFG1, BOOT_CFG2, BOOT_CFG3, BOOT_CFG4 + * see Table 8-11 and Table 5-9 + * BOOT_CFG1[7] = 1 (boot from NAND) + * BOOT_CFG1[5] = 0 - raw NAND + * BOOT_CFG1[4] = 0 - default pad settings + * BOOT_CFG1[3:2] = 00 - devices = 1 + * BOOT_CFG1[1:0] = 00 - Row Address Cycles = 3 + * BOOT_CFG2[4:3] = 00 - Boot Search Count = 2 + * BOOT_CFG2[2:1] = 01 - Pages In Block = 64 + * BOOT_CFG2[0] = 0 - Reset time 12ms + */ +static const struct boot_mode board_boot_modes[] = { + /* NAND: 64pages per block, 3 row addr cycles, 2 copies of FCB/DBBT */ + { "nand", MAKE_CFGVAL(0x80, 0x02, 0x00, 0x00) }, + { NULL, 0 }, +}; +#endif + +/* late init */ +int misc_init_r(void) +{ + struct ventana_board_info *info = &ventana_info; + unsigned char reg; + + /* set env vars based on EEPROM data */ + if (ventana_info.model[0]) { + char str[16], fdt[36]; + char *p; + const char *cputype = ""; + int i; + + /* + * FDT name will be prefixed with CPU type. Three versions + * will be created each increasingly generic and bootloader + * env scripts will try loading each from most specific to + * least. + */ + if (is_cpu_type(MXC_CPU_MX6Q)) + cputype = "imx6q"; + else if (is_cpu_type(MXC_CPU_MX6DL)) + cputype = "imx6dl"; + memset(str, 0, sizeof(str)); + for (i = 0; i < (sizeof(str)-1) && info->model[i]; i++) + str[i] = tolower(info->model[i]); + if (!getenv("model")) + setenv("model", str); + if (!getenv("fdt_file")) { + sprintf(fdt, "%s-%s.dtb", cputype, str); + setenv("fdt_file", fdt); + } + p = strchr(str, '-'); + if (p) { + *p++ = 0; + + setenv("model_base", str); + if (!getenv("fdt_file1")) { + sprintf(fdt, "%s-%s.dtb", cputype, str); + setenv("fdt_file1", fdt); + } + str[4] = 'x'; + str[5] = 'x'; + str[6] = 0; + if (!getenv("fdt_file2")) { + sprintf(fdt, "%s-%s.dtb", cputype, str); + setenv("fdt_file2", fdt); + } + } + + /* initialize env from EEPROM */ + if (test_bit(EECONFIG_ETH0, info->config) && + !getenv("ethaddr")) { + eth_setenv_enetaddr("ethaddr", info->mac0); + } + if (test_bit(EECONFIG_ETH1, info->config) && + !getenv("eth1addr")) { + eth_setenv_enetaddr("eth1addr", info->mac1); + } + + /* board serial-number */ + sprintf(str, "%6d", info->serial); + setenv("serial#", str); + } + + /* configure PFUZE100 PMIC (not used on all Ventana baseboards) */ + if ((board_type == GW54xx || board_type == GW54proto) && + !pmic_init(I2C_PMIC)) { + struct pmic *p = pmic_get("PFUZE100_PMIC"); + u32 reg; + if (p && !pmic_probe(p)) { + pmic_reg_read(p, PFUZE100_DEVICEID, ®); + printf("PMIC: PFUZE100 ID=0x%02x\n", reg); + + /* Set VGEN1 to 1.5V and enable */ + pmic_reg_read(p, PFUZE100_VGEN1VOL, ®); + reg &= ~(LDO_VOL_MASK); + reg |= (LDOA_1_50V | LDO_EN); + pmic_reg_write(p, PFUZE100_VGEN1VOL, reg); + + /* Set SWBST to 5.0V and enable */ + pmic_reg_read(p, PFUZE100_SWBSTCON1, ®); + reg &= ~(SWBST_MODE_MASK | SWBST_VOL_MASK); + reg |= (SWBST_5_00V | SWBST_MODE_AUTO); + pmic_reg_write(p, PFUZE100_SWBSTCON1, reg); + } + } + + /* setup baseboard specific GPIO pinmux and config */ + setup_board_gpio(board_type); + +#ifdef CONFIG_CMD_BMODE + add_board_boot_modes(board_boot_modes); +#endif + + /* + * The Gateworks System Controller implements a boot + * watchdog (always enabled) as a workaround for IMX6 boot related + * errata such as: + * ERR005768 - no fix + * ERR006282 - fixed in silicon r1.3 + * ERR007117 - fixed in silicon r1.3 + * ERR007220 - fixed in silicon r1.3 + * see http://cache.freescale.com/files/32bit/doc/errata/IMX6DQCE.pdf + * + * Disable the boot watchdog and display/clear the timeout flag if set + */ + i2c_set_bus_num(I2C_GSC); + if (!gsc_i2c_read(GSC_SC_ADDR, GSC_SC_CTRL1, 1, ®, 1)) { + reg |= (1 << GSC_SC_CTRL1_WDDIS); + if (gsc_i2c_write(GSC_SC_ADDR, GSC_SC_CTRL1, 1, ®, 1)) + puts("Error: could not disable GSC Watchdog\n"); + } else { + puts("Error: could not disable GSC Watchdog\n"); + } + if (!gsc_i2c_read(GSC_SC_ADDR, GSC_SC_STATUS, 1, ®, 1)) { + if (reg & (1 << GSC_SC_IRQ_WATCHDOG)) { /* watchdog timeout */ + puts("GSC boot watchdog timeout detected"); + reg &= ~(1 << GSC_SC_IRQ_WATCHDOG); /* clear flag */ + gsc_i2c_write(GSC_SC_ADDR, GSC_SC_STATUS, 1, ®, 1); + } + } + + return 0; +} + +#if defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP) + +/* FDT aliases associated with EEPROM config bits */ +const char *fdt_aliases[] = { + "ethernet0", + "ethernet1", + "hdmi_out", + "ahci0", + "pcie", + "ssi0", + "ssi1", + "lcd0", + "lvds0", + "lvds1", + "usb0", + "usb1", + "mmc0", + "mmc1", + "mmc2", + "mmc3", + "uart0", + "uart1", + "uart2", + "uart3", + "uart4", + "ipu0", + "ipu1", + "can0", + "mipi_dsi", + "mipi_csi", + "tzasc0", + "tzasc1", + "i2c0", + "i2c1", + "i2c2", + "vpu", + "csi0", + "csi1", + "caam", + NULL, + NULL, + NULL, + NULL, + NULL, + "spi0", + "spi1", + "spi2", + "spi3", + "spi4", + "spi5", + NULL, + NULL, + "pps", + NULL, + NULL, + NULL, + "hdmi_in", + "cvbs_out", + "cvbs_in", + "nand", + NULL, + NULL, + NULL, + NULL, + NULL, + NULL, + NULL, + NULL, +}; + +/* + * called prior to booting kernel or by 'fdt boardsetup' command + * + * unless 'fdt_noauto' env var is set we will update the following in the DTB: + * - mtd partitions based on mtdparts/mtdids env + * - system-serial (board serial num from EEPROM) + * - board (full model from EEPROM) + * - peripherals removed from DTB if not loaded on board (per EEPROM config) + */ +void ft_board_setup(void *blob, bd_t *bd) +{ + int bit; + struct ventana_board_info *info = &ventana_info; + struct node_info nodes[] = { + { "sst,w25q256", MTD_DEV_TYPE_NOR, }, /* SPI flash */ + { "fsl,imx6q-gpmi-nand", MTD_DEV_TYPE_NAND, }, /* NAND flash */ + }; + const char *model = getenv("model"); + + if (getenv("fdt_noauto")) { + puts(" Skiping ft_board_setup (fdt_noauto defined)\n"); + return; + } + + /* Update partition nodes using info from mtdparts env var */ + puts(" Updating MTD partitions...\n"); + fdt_fixup_mtdparts(blob, nodes, ARRAY_SIZE(nodes)); + + if (!model) { + puts("invalid board info: Leaving FDT fully enabled\n"); + return; + } + printf(" Adjusting FDT per EEPROM for %s...\n", model); + + /* board serial number */ + fdt_setprop(blob, 0, "system-serial", getenv("serial#"), + strlen(getenv("serial#") + 1)); + + /* board (model contains model from device-tree) */ + fdt_setprop(blob, 0, "board", info->model, + strlen((const char *)info->model) + 1); + + /* + * Peripheral Config: + * remove nodes by alias path if EEPROM config tells us the + * peripheral is not loaded on the board. + */ + for (bit = 0; bit < 64; bit++) { + if (!test_bit(bit, info->config)) + fdt_del_node_and_alias(blob, fdt_aliases[bit]); + } +} +#endif /* defined(CONFIG_OF_FLAT_TREE) && defined(CONFIG_OF_BOARD_SETUP) */ + diff --git a/board/gateworks/gw_ventana/gw_ventana.cfg b/board/gateworks/gw_ventana/gw_ventana.cfg new file mode 100644 index 0000000..27f0974 --- /dev/null +++ b/board/gateworks/gw_ventana/gw_ventana.cfg @@ -0,0 +1,44 @@ +/* + * Copyright (C) 2013 Gateworks Corporation + * + * SPDX-License-Identifier: GPL-2.0+ + * + * Refer doc/README.imximage for more details about how-to configure + * and create imximage boot image + * + * The syntax is taken as close as possible with the kwbimage + */ + +/* image version */ +IMAGE_VERSION 2 + +/* + * Boot Device : one of + * spi, sd, nand, sata + */ +#ifdef CONFIG_SPI_FLASH +BOOT_FROM spi +#else +BOOT_FROM nand +#endif + +#define __ASSEMBLY__ +#include <config.h> +#include "asm/arch/mx6-ddr.h" +#include "asm/arch/iomux.h" +#include "asm/arch/crm_regs.h" + +/* Memory configuration (size is overridden via eeprom config) */ +#include "../../boundary/nitrogen6x/ddr-setup.cfg" +#if defined(CONFIG_MX6Q) && CONFIG_DDR_MB == 1024 + #include "../../boundary/nitrogen6x/1066mhz_4x128mx16.cfg" +#elif defined(CONFIG_MX6DL) && CONFIG_DDR_MB == 1024 + #include "../../boundary/nitrogen6x/800mhz_4x128mx16.cfg" +#elif defined(CONFIG_MX6DL) && CONFIG_DDR_MB == 512 + #include "../../boundary/nitrogen6x/800mhz_2x128mx16.cfg" +#elif defined(CONFIG_MX6Q) && CONFIG_DDR_MB == 512 + #include "../../boundary/nitrogen6x/800mhz_2x128mx16.cfg" +#else + #error "Unsupported CPU/Memory configuration" +#endif +#include "clocks.cfg" diff --git a/board/gateworks/gw_ventana/ventana_eeprom.h b/board/gateworks/gw_ventana/ventana_eeprom.h new file mode 100644 index 0000000..d310bfd --- /dev/null +++ b/board/gateworks/gw_ventana/ventana_eeprom.h @@ -0,0 +1,106 @@ +/* + * Copyright (C) 2013 Gateworks Corporation + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef _VENTANA_EEPROM_ +#define _VENTANA_EEPROM_ + +struct ventana_board_info { + u8 mac0[6]; /* 0x00: MAC1 */ + u8 mac1[6]; /* 0x06: MAC2 */ + u8 res0[12]; /* 0x0C: reserved */ + u32 serial; /* 0x18: Serial Number (read only) */ + u8 res1[4]; /* 0x1C: reserved */ + u8 mfgdate[4]; /* 0x20: MFG date (read only) */ + u8 res2[7]; /* 0x24 */ + /* sdram config */ + u8 sdram_size; /* 0x2B: enum (512,1024,2048) MB */ + u8 sdram_speed; /* 0x2C: enum (100,133,166,200,267,333,400) MHz */ + u8 sdram_width; /* 0x2D: enum (32,64) bit */ + /* cpu config */ + u8 cpu_speed; /* 0x2E: enum (800,1000,1200) MHz */ + u8 cpu_type; /* 0x2F: enum (imx6q,imx6d,imx6dl,imx6s) */ + u8 model[16]; /* 0x30: model string */ + /* FLASH config */ + u8 nand_flash_size; /* 0x40: enum (4,8,16,32,64,128) MB */ + u8 spi_flash_size; /* 0x41: enum (4,8,16,32,64,128) MB */ + + /* Config1: SoC Peripherals */ + u8 config[8]; /* 0x42: loading options */ + + u8 res3[4]; /* 0x4A */ + + u8 chksum[2]; /* 0x4E */ +}; + +/* config bits */ +enum { + EECONFIG_ETH0, + EECONFIG_ETH1, + EECONFIG_HDMI_OUT, + EECONFIG_SATA, + EECONFIG_PCIE, + EECONFIG_SSI0, + EECONFIG_SSI1, + EECONFIG_LCD, + EECONFIG_LVDS0, + EECONFIG_LVDS1, + EECONFIG_USB0, + EECONFIG_USB1, + EECONFIG_SD0, + EECONFIG_SD1, + EECONFIG_SD2, + EECONFIG_SD3, + EECONFIG_UART0, + EECONFIG_UART1, + EECONFIG_UART2, + EECONFIG_UART3, + EECONFIG_UART4, + EECONFIG_IPU0, + EECONFIG_IPU1, + EECONFIG_FLEXCAN, + EECONFIG_MIPI_DSI, + EECONFIG_MIPI_CSI, + EECONFIG_TZASC0, + EECONFIG_TZASC1, + EECONFIG_I2C0, + EECONFIG_I2C1, + EECONFIG_I2C2, + EECONFIG_VPU, + EECONFIG_CSI0, + EECONFIG_CSI1, + EECONFIG_CAAM, + EECONFIG_MEZZ, + EECONFIG_RES1, + EECONFIG_RES2, + EECONFIG_RES3, + EECONFIG_RES4, + EECONFIG_ESPCI0, + EECONFIG_ESPCI1, + EECONFIG_ESPCI2, + EECONFIG_ESPCI3, + EECONFIG_ESPCI4, + EECONFIG_ESPCI5, + EECONFIG_RES5, + EECONFIG_RES6, + EECONFIG_GPS, + EECONFIG_SPIFL0, + EECONFIG_SPIFL1, + EECONFIG_GSPBATT, + EECONFIG_HDMI_IN, + EECONFIG_VID_OUT, + EECONFIG_VID_IN, + EECONFIG_NAND, + EECONFIG_RES8, + EECONFIG_RES9, + EECONFIG_RES10, + EECONFIG_RES11, + EECONFIG_RES12, + EECONFIG_RES13, + EECONFIG_RES14, + EECONFIG_RES15, +}; + +#endif |