summaryrefslogtreecommitdiff
path: root/board/hymod
diff options
context:
space:
mode:
Diffstat (limited to 'board/hymod')
-rw-r--r--board/hymod/bsp.c307
-rw-r--r--board/hymod/hymod.c802
2 files changed, 1109 insertions, 0 deletions
diff --git a/board/hymod/bsp.c b/board/hymod/bsp.c
new file mode 100644
index 0000000..a33c97c
--- /dev/null
+++ b/board/hymod/bsp.c
@@ -0,0 +1,307 @@
+/*
+ * (C) Copyright 2000
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ * hacked for Hymod FPGA support by Murray.Jensen@cmst.csiro.au, 29-Jan-01
+ */
+
+#include <common.h>
+#include <command.h>
+#include <net.h>
+#include <i2c.h>
+#include <asm/iopin_8260.h>
+#include <cmd_bsp.h>
+
+/*-----------------------------------------------------------------------
+ * Board Special Commands: FPGA load/store, EEPROM erase
+ */
+
+#if (CONFIG_COMMANDS & CFG_CMD_BSP)
+
+#define LOAD_SUCCESS 0
+#define LOAD_FAIL_NOCONF 1
+#define LOAD_FAIL_NOINIT 2
+#define LOAD_FAIL_NODONE 3
+
+#define STORE_SUCCESS 0
+
+/*
+ * Programming the Hymod FPGAs
+ *
+ * The 8260 io port config table is set up so that the INIT pin is
+ * held Low (Open Drain output 0) - this will delay the automatic
+ * Power-On config until INIT is released (by making it an input).
+ *
+ * If the FPGA has been programmed before, then the assertion of PROGRAM
+ * will initiate configuration (i.e. it begins clearing the RAM).
+ *
+ * When the FPGA is ready to receive configuration data (either after
+ * releasing INIT after Power-On, or after asserting PROGRAM), it will
+ * pull INIT high.
+ *
+ * Notes from Paul Dunn:
+ *
+ * 1. program pin should be forced low for >= 300ns
+ * (about 20 bus clock cycles minimum).
+ *
+ * 2. then wait for init to go high, which signals
+ * that the FPGA has cleared its internal memory
+ * and is ready to load
+ *
+ * 3. perform load writes of entire config file
+ *
+ * 4. wait for done to go high, which should be
+ * within a few bus clock cycles. If done has not
+ * gone high after reasonable period, then load
+ * has not worked (wait several ms?)
+ */
+
+int fpga_load (int mezz, uchar * addr, ulong size)
+{
+ DECLARE_GLOBAL_DATA_PTR;
+
+ hymod_conf_t *cp = &gd->bd->bi_hymod_conf;
+ xlx_iopins_t *fpgaio;
+ volatile uchar *fpgabase;
+ volatile uint cnt;
+ uchar *eaddr = addr + size;
+ int result;
+
+ if (mezz) {
+ if (!cp->mezz.mmap[0].prog.exists)
+ return (LOAD_FAIL_NOCONF);
+ fpgabase = (uchar *) cp->mezz.mmap[0].prog.base;
+ fpgaio = &cp->mezz.iopins[0];
+ } else {
+ if (!cp->main.mmap[0].prog.exists)
+ return (LOAD_FAIL_NOCONF);
+ fpgabase = (uchar *) cp->main.mmap[0].prog.base;
+ fpgaio = &cp->main.iopins[0];
+ }
+
+ /* set enable HIGH if required */
+ if (fpgaio->enable_pin.flag)
+ iopin_set_high (&fpgaio->enable_pin);
+
+ /* ensure INIT is released (set it to be an input) */
+ iopin_set_in (&fpgaio->init_pin);
+
+ /* toggle PROG Low then High (will already be Low after Power-On) */
+ iopin_set_low (&fpgaio->prog_pin);
+ udelay (1); /* minimum 300ns - 1usec should do it */
+ iopin_set_high (&fpgaio->prog_pin);
+
+ /* wait for INIT High */
+ cnt = 0;
+ while (!iopin_is_high (&fpgaio->init_pin))
+ if (++cnt == 10000000) {
+ result = LOAD_FAIL_NOINIT;
+ goto done;
+ }
+
+ /* write configuration data */
+ while (addr < eaddr)
+ *fpgabase = *addr++;
+
+ /* wait for DONE High */
+ cnt = 0;
+ while (!iopin_is_high (&fpgaio->done_pin))
+ if (++cnt == 100000000) {
+ result = LOAD_FAIL_NODONE;
+ goto done;
+ }
+
+ /* success */
+ result = LOAD_SUCCESS;
+
+ done:
+
+ if (fpgaio->enable_pin.flag)
+ iopin_set_low (&fpgaio->enable_pin);
+
+ return (result);
+}
+
+/* ------------------------------------------------------------------------- */
+int
+do_fpga (cmd_tbl_t * cmdtp, int flag, int argc, char *argv[])
+{
+ uchar *addr, *save_addr;
+ ulong size;
+ int mezz, arg, result;
+
+ switch (argc) {
+
+ case 0:
+ case 1:
+ break;
+
+ case 2:
+ if (strcmp (argv[1], "info") == 0) {
+ printf ("\nHymod FPGA Info...\n");
+ printf (" Address Size\n");
+ printf (" Main Configuration: 0x%08x %d\n",
+ FPGA_MAIN_CFG_BASE, FPGA_MAIN_CFG_SIZE);
+ printf (" Main Register: 0x%08x %d\n",
+ FPGA_MAIN_REG_BASE, FPGA_MAIN_REG_SIZE);
+ printf (" Main Port: 0x%08x %d\n",
+ FPGA_MAIN_PORT_BASE, FPGA_MAIN_PORT_SIZE);
+ printf (" Mezz Configuration: 0x%08x %d\n",
+ FPGA_MEZZ_CFG_BASE, FPGA_MEZZ_CFG_SIZE);
+ return 0;
+ }
+ break;
+
+ case 3:
+ if (strcmp (argv[1], "store") == 0) {
+ addr = (uchar *) simple_strtoul (argv[2], NULL, 16);
+
+ save_addr = addr;
+#if 0
+ /* reading config data unimplemented */
+ while VM
+ :more config data * addr++ = *fpga;
+ result = VM:? ? ?
+#else
+ result = 0;
+#endif
+ if (result == STORE_SUCCESS) {
+ printf ("SUCCEEDED (%d bytes)\n", addr - save_addr);
+ return 0;
+ } else
+ printf ("FAILED (%d bytes)\n", addr - save_addr);
+ return 1;
+ }
+ break;
+
+ case 4:
+ if (strcmp (argv[1], "tftp") == 0) {
+ copy_filename (BootFile, argv[2], sizeof (BootFile));
+ load_addr = simple_strtoul (argv[3], NULL, 16);
+
+ if (NetLoop (TFTP) == 0) {
+ printf ("tftp transfer failed - aborting fgpa load\n");
+ return 1;
+ }
+
+ if (NetBootFileXferSize == 0) {
+ printf ("can't determine file size - aborting fpga load\n");
+ return 1;
+ }
+
+ printf ("File transfer succeeded - beginning fpga load...");
+
+ result = fpga_load (0, (uchar *) load_addr,
+ NetBootFileXferSize);
+ if (result == LOAD_SUCCESS) {
+ printf ("SUCCEEDED\n");
+ return 0;
+ } else if (result == LOAD_FAIL_NOINIT)
+ printf ("FAILED (no INIT)\n");
+ else
+ printf ("FAILED (no DONE)\n");
+ return 1;
+
+ }
+ /* fall through ... */
+
+ case 5:
+ if (strcmp (argv[1], "load") == 0) {
+ if (argc == 5) {
+ if (strcmp (argv[2], "main") == 0)
+ mezz = 0;
+ else if (strcmp (argv[2], "mezz") == 0)
+ mezz = 1;
+ else {
+ printf ("FPGA type must be either `main' or `mezz'\n");
+ return 1;
+ }
+ arg = 3;
+ } else {
+ mezz = 0;
+ arg = 2;
+ }
+ addr = (uchar *) simple_strtoul (argv[arg++], NULL, 16);
+ size = (ulong) simple_strtoul (argv[arg], NULL, 16);
+
+ result = fpga_load (mezz, addr, size);
+ if (result == LOAD_SUCCESS) {
+ printf ("SUCCEEDED\n");
+ return 0;
+ } else if (result == LOAD_FAIL_NOINIT)
+ printf ("FAILED (no INIT)\n");
+ else
+ printf ("FAILED (no DONE)\n");
+ return 1;
+ }
+ break;
+
+ default:
+ break;
+ }
+
+ printf ("Usage:\n%s\n", cmdtp->usage);
+ return 1;
+}
+
+/* ------------------------------------------------------------------------- */
+int
+do_eecl (cmd_tbl_t * cmdtp, int flag, int argc, char *argv[])
+{
+ uchar data[HYMOD_EEPROM_SIZE];
+ uint offset;
+ int rcode = 0;
+
+ switch (argc) {
+
+ case 1:
+ offset = HYMOD_EEOFF_MAIN;
+ break;
+
+ case 2:
+ if (strcmp (argv[1], "main") == 0) {
+ offset = HYMOD_EEOFF_MAIN;
+ break;
+ }
+ if (strcmp (argv[1], "mezz") == 0) {
+ offset = HYMOD_EEOFF_MEZZ;
+ break;
+ }
+ /* fall through ... */
+
+ default:
+ printf ("Usage:\n%s\n", cmdtp->usage);
+ return 1;
+ }
+
+ memset (data, 0, HYMOD_EEPROM_SIZE);
+ if (i2c_write
+ (CFG_I2C_EEPROM_ADDR | offset, 0, CFG_I2C_EEPROM_ADDR_LEN, data,
+ HYMOD_EEPROM_SIZE)) {
+ rcode = 1;
+ }
+
+ return rcode;
+}
+
+#endif /* CFG_CMD_BSP */
+
+/* ------------------------------------------------------------------------- */
diff --git a/board/hymod/hymod.c b/board/hymod/hymod.c
new file mode 100644
index 0000000..829f254
--- /dev/null
+++ b/board/hymod/hymod.c
@@ -0,0 +1,802 @@
+/*
+ * (C) Copyright 2000
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ * Hacked for the Hymod board by Murray.Jensen@cmst.csiro.au, 20-Oct-00
+ */
+
+#include <common.h>
+#include <mpc8260.h>
+#include <ioports.h>
+#include <i2c.h>
+#include <asm/iopin_8260.h>
+
+/* ------------------------------------------------------------------------- */
+
+/* imports from eeprom.c */
+extern int eeprom_load (unsigned, hymod_eeprom_t *);
+extern int eeprom_fetch (unsigned, char *, ulong);
+extern void eeprom_print (hymod_eeprom_t *);
+
+/* imports from fetch.c */
+extern int fetch_and_parse (char *, ulong, int (*)(uchar *, uchar *));
+
+/* imports from common/main.c */
+extern char console_buffer[CFG_CBSIZE];
+
+/* ------------------------------------------------------------------------- */
+
+/*
+ * I/O Port configuration table
+ *
+ * if conf is 1, then that port pin will be configured at boot time
+ * according to the five values podr/pdir/ppar/psor/pdat for that entry
+ */
+
+const iop_conf_t iop_conf_tab[4][32] = {
+
+ /* Port A configuration */
+ { /* conf ppar psor pdir podr pdat */
+ /* PA31 */ {1, 1, 1, 0, 0, 0},
+ /* FCC1 MII COL */
+ /* PA30 */ {1, 1, 1, 0, 0, 0},
+ /* FCC1 MII CRS */
+ /* PA29 */ {1, 1, 1, 1, 0, 0},
+ /* FCC1 MII TX_ER */
+ /* PA28 */ {1, 1, 1, 1, 0, 0},
+ /* FCC1 MII TX_EN */
+ /* PA27 */ {1, 1, 1, 0, 0, 0},
+ /* FCC1 MII RX_DV */
+ /* PA26 */ {1, 1, 1, 0, 0, 0},
+ /* FCC1 MII RX_ER */
+ /* PA25 */ {1, 0, 0, 1, 0, 0},
+ /* FCC2 MII MDIO */
+ /* PA24 */ {1, 0, 0, 1, 0, 0},
+ /* FCC2 MII MDC */
+ /* PA23 */ {1, 0, 0, 1, 0, 0},
+ /* FCC3 MII MDIO */
+ /* PA22 */ {1, 0, 0, 1, 0, 0},
+ /* FCC3 MII MDC */
+ /* PA21 */ {1, 1, 0, 1, 0, 0},
+ /* FCC1 MII TxD[3] */
+ /* PA20 */ {1, 1, 0, 1, 0, 0},
+ /* FCC1 MII TxD[2] */
+ /* PA19 */ {1, 1, 0, 1, 0, 0},
+ /* FCC1 MII TxD[1] */
+ /* PA18 */ {1, 1, 0, 1, 0, 0},
+ /* FCC1 MII TxD[0] */
+ /* PA17 */ {1, 1, 0, 0, 0, 0},
+ /* FCC1 MII RxD[3] */
+ /* PA16 */ {1, 1, 0, 0, 0, 0},
+ /* FCC1 MII RxD[2] */
+ /* PA15 */ {1, 1, 0, 0, 0, 0},
+ /* FCC1 MII RxD[1] */
+ /* PA14 */ {1, 1, 0, 0, 0, 0},
+ /* FCC1 MII RxD[0] */
+ /* PA13 */ {1, 0, 0, 1, 0, 0},
+ /* FCC1 MII MDIO */
+ /* PA12 */ {1, 0, 0, 1, 0, 0},
+ /* FCC1 MII MDC */
+ /* PA11 */ {1, 0, 0, 1, 0, 0},
+ /* SEL_CD */
+ /* PA10 */ {1, 0, 0, 0, 0, 0},
+ /* FLASH STS1 */
+ /* PA9 */ {1, 0, 0, 0, 0, 0},
+ /* FLASH STS0 */
+ /* PA8 */ {1, 0, 0, 0, 0, 0},
+ /* FLASH ~PE */
+ /* PA7 */ {1, 0, 0, 0, 0, 0},
+ /* WATCH ~HRESET */
+ /* PA6 */ {1, 0, 0, 0, 1, 0},
+ /* VC DONE */
+ /* PA5 */ {1, 0, 0, 1, 1, 0},
+ /* VC INIT */
+ /* PA4 */ {1, 0, 0, 1, 0, 0},
+ /* VC ~PROG */
+ /* PA3 */ {1, 0, 0, 1, 0, 0},
+ /* VM ENABLE */
+ /* PA2 */ {1, 0, 0, 0, 1, 0},
+ /* VM DONE */
+ /* PA1 */ {1, 0, 0, 1, 1, 0},
+ /* VM INIT */
+ /* PA0 */ {1, 0, 0, 1, 0, 0}
+ /* VM ~PROG */
+ },
+
+ /* Port B configuration */
+ { /* conf ppar psor pdir podr pdat */
+ /* PB31 */ {1, 1, 0, 1, 0, 0},
+ /* FCC2 MII TX_ER */
+ /* PB30 */ {1, 1, 0, 0, 0, 0},
+ /* FCC2 MII RX_DV */
+ /* PB29 */ {1, 1, 1, 1, 0, 0},
+ /* FCC2 MII TX_EN */
+ /* PB28 */ {1, 1, 0, 0, 0, 0},
+ /* FCC2 MII RX_ER */
+ /* PB27 */ {1, 1, 0, 0, 0, 0},
+ /* FCC2 MII COL */
+ /* PB26 */ {1, 1, 0, 0, 0, 0},
+ /* FCC2 MII CRS */
+ /* PB25 */ {1, 1, 0, 1, 0, 0},
+ /* FCC2 MII TxD[3] */
+ /* PB24 */ {1, 1, 0, 1, 0, 0},
+ /* FCC2 MII TxD[2] */
+ /* PB23 */ {1, 1, 0, 1, 0, 0},
+ /* FCC2 MII TxD[1] */
+ /* PB22 */ {1, 1, 0, 1, 0, 0},
+ /* FCC2 MII TxD[0] */
+ /* PB21 */ {1, 1, 0, 0, 0, 0},
+ /* FCC2 MII RxD[0] */
+ /* PB20 */ {1, 1, 0, 0, 0, 0},
+ /* FCC2 MII RxD[1] */
+ /* PB19 */ {1, 1, 0, 0, 0, 0},
+ /* FCC2 MII RxD[2] */
+ /* PB18 */ {1, 1, 0, 0, 0, 0},
+ /* FCC2 MII RxD[3] */
+ /* PB17 */ {1, 1, 0, 0, 0, 0},
+ /* FCC3 MII RX_DV */
+ /* PB16 */ {1, 1, 0, 0, 0, 0},
+ /* FCC3 MII RX_ER */
+ /* PB15 */ {1, 1, 0, 1, 0, 0},
+ /* FCC3 MII TX_ER */
+ /* PB14 */ {1, 1, 0, 1, 0, 0},
+ /* FCC3 MII TX_EN */
+ /* PB13 */ {1, 1, 0, 0, 0, 0},
+ /* FCC3 MII COL */
+ /* PB12 */ {1, 1, 0, 0, 0, 0},
+ /* FCC3 MII CRS */
+ /* PB11 */ {1, 1, 0, 0, 0, 0},
+ /* FCC3 MII RxD[3] */
+ /* PB10 */ {1, 1, 0, 0, 0, 0},
+ /* FCC3 MII RxD[2] */
+ /* PB9 */ {1, 1, 0, 0, 0, 0},
+ /* FCC3 MII RxD[1] */
+ /* PB8 */ {1, 1, 0, 0, 0, 0},
+ /* FCC3 MII RxD[0] */
+ /* PB7 */ {1, 1, 0, 1, 0, 0},
+ /* FCC3 MII TxD[3] */
+ /* PB6 */ {1, 1, 0, 1, 0, 0},
+ /* FCC3 MII TxD[2] */
+ /* PB5 */ {1, 1, 0, 1, 0, 0},
+ /* FCC3 MII TxD[1] */
+ /* PB4 */ {1, 1, 0, 1, 0, 0},
+ /* FCC3 MII TxD[0] */
+ /* PB3 */ {0, 0, 0, 0, 0, 0},
+ /* pin doesn't exist */
+ /* PB2 */ {0, 0, 0, 0, 0, 0},
+ /* pin doesn't exist */
+ /* PB1 */ {0, 0, 0, 0, 0, 0},
+ /* pin doesn't exist */
+ /* PB0 */ {0, 0, 0, 0, 0, 0}
+ /* pin doesn't exist */
+ },
+
+ /* Port C */
+ { /* conf ppar psor pdir podr pdat */
+ /* PC31 */ {1, 0, 0, 0, 0, 0},
+ /* MEZ ~IACK */
+ /* PC30 */ {0, 0, 0, 0, 0, 0},
+ /* PC29 */ {1, 1, 0, 0, 0, 0},
+ /* CLK SCCx */
+ /* PC28 */ {1, 1, 0, 0, 0, 0},
+ /* CLK4 */
+ /* PC27 */ {1, 1, 0, 0, 0, 0},
+ /* CLK SCCF */
+ /* PC26 */ {1, 1, 0, 0, 0, 0},
+ /* CLK 32K */
+ /* PC25 */ {1, 1, 0, 0, 0, 0},
+ /* BRG4/CLK7 */
+ /* PC24 */ {0, 0, 0, 0, 0, 0},
+ /* PC23 */ {1, 1, 0, 0, 0, 0},
+ /* CLK SCCx */
+ /* PC22 */ {1, 1, 0, 0, 0, 0},
+ /* FCC1 MII RX_CLK */
+ /* PC21 */ {1, 1, 0, 0, 0, 0},
+ /* FCC1 MII TX_CLK */
+ /* PC20 */ {1, 1, 0, 0, 0, 0},
+ /* CLK SCCF */
+ /* PC19 */ {1, 1, 0, 0, 0, 0},
+ /* FCC2 MII RX_CLK */
+ /* PC18 */ {1, 1, 0, 0, 0, 0},
+ /* FCC2 MII TX_CLK */
+ /* PC17 */ {1, 1, 0, 0, 0, 0},
+ /* FCC3 MII RX_CLK */
+ /* PC16 */ {1, 1, 0, 0, 0, 0},
+ /* FCC3 MII TX_CLK */
+ /* PC15 */ {1, 0, 0, 0, 0, 0},
+ /* SCC1 UART ~CTS */
+ /* PC14 */ {1, 0, 0, 0, 0, 0},
+ /* SCC1 UART ~CD */
+ /* PC13 */ {1, 0, 0, 0, 0, 0},
+ /* SCC2 UART ~CTS */
+ /* PC12 */ {1, 0, 0, 0, 0, 0},
+ /* SCC2 UART ~CD */
+ /* PC11 */ {1, 0, 0, 1, 0, 0},
+ /* SCC1 UART ~DTR */
+ /* PC10 */ {1, 0, 0, 1, 0, 0},
+ /* SCC1 UART ~DSR */
+ /* PC9 */ {1, 0, 0, 1, 0, 0},
+ /* SCC2 UART ~DTR */
+ /* PC8 */ {1, 0, 0, 1, 0, 0},
+ /* SCC2 UART ~DSR */
+ /* PC7 */ {1, 0, 0, 0, 0, 0},
+ /* TEMP ~ALERT */
+ /* PC6 */ {1, 0, 0, 0, 0, 0},
+ /* FCC3 INT */
+ /* PC5 */ {1, 0, 0, 0, 0, 0},
+ /* FCC2 INT */
+ /* PC4 */ {1, 0, 0, 0, 0, 0},
+ /* FCC1 INT */
+ /* PC3 */ {1, 1, 1, 1, 0, 0},
+ /* SDMA IDMA2 ~DACK */
+ /* PC2 */ {1, 1, 1, 0, 0, 0},
+ /* SDMA IDMA2 ~DONE */
+ /* PC1 */ {1, 1, 0, 0, 0, 0},
+ /* SDMA IDMA2 ~DREQ */
+ /* PC0 */ {1, 1, 0, 1, 0, 0}
+ /* BRG7 */
+ },
+
+ /* Port D */
+ { /* conf ppar psor pdir podr pdat */
+ /* PD31 */ {1, 1, 0, 0, 0, 0},
+ /* SCC1 UART RxD */
+ /* PD30 */ {1, 1, 1, 1, 0, 0},
+ /* SCC1 UART TxD */
+ /* PD29 */ {1, 0, 0, 1, 0, 0},
+ /* SCC1 UART ~RTS */
+ /* PD28 */ {1, 1, 0, 0, 0, 0},
+ /* SCC2 UART RxD */
+ /* PD27 */ {1, 1, 0, 1, 0, 0},
+ /* SCC2 UART TxD */
+ /* PD26 */ {1, 0, 0, 1, 0, 0},
+ /* SCC2 UART ~RTS */
+ /* PD25 */ {1, 0, 0, 0, 0, 0},
+ /* SCC1 UART ~RI */
+ /* PD24 */ {1, 0, 0, 0, 0, 0},
+ /* SCC2 UART ~RI */
+ /* PD23 */ {1, 0, 0, 1, 0, 0},
+ /* CLKGEN PD */
+ /* PD22 */ {1, 0, 0, 0, 0, 0},
+ /* USER3 */
+ /* PD21 */ {1, 0, 0, 0, 0, 0},
+ /* USER2 */
+ /* PD20 */ {1, 0, 0, 0, 0, 0},
+ /* USER1 */
+ /* PD19 */ {1, 1, 1, 0, 0, 0},
+ /* SPI ~SEL */
+ /* PD18 */ {1, 1, 1, 0, 0, 0},
+ /* SPI CLK */
+ /* PD17 */ {1, 1, 1, 0, 0, 0},
+ /* SPI MOSI */
+ /* PD16 */ {1, 1, 1, 0, 0, 0},
+ /* SPI MISO */
+ /* PD15 */ {1, 1, 1, 0, 1, 0},
+ /* I2C SDA */
+ /* PD14 */ {1, 1, 1, 0, 1, 0},
+ /* I2C SCL */
+ /* PD13 */ {1, 0, 0, 1, 0, 1},
+ /* TEMP ~STDBY */
+ /* PD12 */ {1, 0, 0, 1, 0, 1},
+ /* FCC3 ~RESET */
+ /* PD11 */ {1, 0, 0, 1, 0, 1},
+ /* FCC2 ~RESET */
+ /* PD10 */ {1, 0, 0, 1, 0, 1},
+ /* FCC1 ~RESET */
+ /* PD9 */ {1, 0, 0, 0, 0, 0},
+ /* PD9 */
+ /* PD8 */ {1, 0, 0, 0, 0, 0},
+ /* PD8 */
+ /* PD7 */ {1, 0, 0, 1, 0, 1},
+ /* PD7 */
+ /* PD6 */ {1, 0, 0, 1, 0, 1},
+ /* PD6 */
+ /* PD5 */ {1, 0, 0, 1, 0, 1},
+ /* PD5 */
+ /* PD4 */ {1, 0, 0, 1, 0, 1},
+ /* PD4 */
+ /* PD3 */ {0, 0, 0, 0, 0, 0},
+ /* pin doesn't exist */
+ /* PD2 */ {0, 0, 0, 0, 0, 0},
+ /* pin doesn't exist */
+ /* PD1 */ {0, 0, 0, 0, 0, 0},
+ /* pin doesn't exist */
+ /* PD0 */ {0, 0, 0, 0, 0, 0}
+ /* pin doesn't exist */
+ }
+};
+
+/* ------------------------------------------------------------------------- */
+
+/*
+ * AMI FS6377 Clock Generator configuration table
+ *
+ * the "fs6377_regs[]" table entries correspond to FS6377 registers
+ * 0 - 15 (total of 16 bytes).
+ *
+ * the data is written to the FS6377 via the i2c bus using address in
+ * "fs6377_addr" (address is 7 bits - R/W bit not included).
+ */
+
+uchar fs6377_addr = 0x5c;
+
+uchar fs6377_regs[16] = {
+ 12, 75, 64, 25, 144, 128, 25, 192,
+ 0, 16, 135, 192, 224, 64, 64, 192
+};
+
+iopin_t pa11 = { IOPIN_PORTA, 11, 0 };
+
+/* ------------------------------------------------------------------------- */
+
+/*
+ * special board initialisation, after clocks and timebase have been
+ * set up but before environment and serial are initialised.
+ *
+ * added so that very early initialisations can be done using the i2c
+ * driver (which requires the clocks, to calculate the dividers, and
+ * the timebase, for udelay())
+ */
+
+int board_postclk_init (void)
+{
+ i2c_init (CFG_I2C_SPEED, CFG_I2C_SLAVE);
+
+ /*
+ * Initialise the FS6377 clock chip
+ *
+ * the secondary address is the register number from where to
+ * start the write - I want to write all the registers
+ *
+ * don't bother checking return status - we have no console yet
+ * to print it on, nor any RAM to store it in - it will be obvious
+ * if this doesn't work
+ */
+ (void) i2c_write (fs6377_addr, 0, 1, fs6377_regs,
+ sizeof (fs6377_regs));
+
+ return (0);
+}
+
+/* ------------------------------------------------------------------------- */
+
+/*
+ * Check Board Identity: Hardwired to HYMOD
+ */
+
+int checkboard (void)
+{
+ puts ("Board: HYMOD\n");
+ return (0);
+}
+
+/* ------------------------------------------------------------------------- */
+
+/*
+ * miscellaneous (early - while running in flash) initialisations.
+ */
+
+#define _NOT_USED_ 0xFFFFFFFF
+
+uint upmb_table[] = {
+ /* Read Single Beat (RSS) - offset 0x00 */
+ _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+ _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+ /* Read Burst (RBS) - offset 0x08 */
+ _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+ _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+ _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+ _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+ /* Write Single Beat (WSS) - offset 0x18 */
+ _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+ _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+ /* Write Burst (WSS) - offset 0x20 */
+ _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+ _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+ _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+ _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+ /* Refresh Timer (PTS) - offset 0x30 */
+ _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+ _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+ _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+ /* Exception Condition (EXS) - offset 0x3c */
+ _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_
+};
+
+uint upmc_table[] = {
+ /* Read Single Beat (RSS) - offset 0x00 */
+ _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+ _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+ /* Read Burst (RBS) - offset 0x08 */
+ _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+ _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+ _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+ _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+ /* Write Single Beat (WSS) - offset 0x18 */
+ 0xF0E00000, 0xF0A00000, 0x00A00000, 0x30A00000,
+ 0xF0F40007, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+ /* Write Burst (WSS) - offset 0x20 */
+ _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+ _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+ _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+ _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+ /* Refresh Timer (PTS) - offset 0x30 */
+ _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+ _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+ _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+ /* Exception Condition (EXS) - offset 0x3c */
+ _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_
+};
+
+int misc_init_f (void)
+{
+ volatile immap_t *immap = (immap_t *) CFG_IMMR;
+ volatile memctl8260_t *memctl = &immap->im_memctl;
+
+ printf ("UPMs: ");
+
+ upmconfig (UPMB, upmb_table, sizeof upmb_table / sizeof upmb_table[0]);
+ memctl->memc_mbmr = CFG_MBMR;
+
+ upmconfig (UPMC, upmc_table, sizeof upmc_table / sizeof upmc_table[0]);
+ memctl->memc_mcmr = CFG_MCMR;
+
+ printf ("configured\n");
+ return (0);
+}
+
+/* ------------------------------------------------------------------------- */
+
+long initdram (int board_type)
+{
+ volatile immap_t *immap = (immap_t *) CFG_IMMR;
+ volatile memctl8260_t *memctl = &immap->im_memctl;
+ volatile uchar c = 0, *ramaddr = (uchar *) (CFG_SDRAM_BASE + 0x8);
+ ulong psdmr = CFG_PSDMR;
+ int i;
+
+ /*
+ * Quote from 8260 UM (10.4.2 SDRAM Power-On Initialization, 10-35):
+ *
+ * "At system reset, initialization software must set up the
+ * programmable parameters in the memory controller banks registers
+ * (ORx, BRx, P/LSDMR). After all memory parameters are coñgured,
+ * system software should execute the following initialization sequence
+ * for each SDRAM device.
+ *
+ * 1. Issue a PRECHARGE-ALL-BANKS command
+ * 2. Issue eight CBR REFRESH commands
+ * 3. Issue a MODE-SET command to initialize the mode register
+ *
+ * The initial commands are executed by setting P/LSDMR[OP] and
+ * accessing the SDRAM with a single-byte transaction."
+ *
+ * The appropriate BRx/ORx registers have already been set when we
+ * get here. The SDRAM can be accessed at the address CFG_SDRAM_BASE.
+ */
+
+ memctl->memc_psrt = CFG_PSRT;
+ memctl->memc_mptpr = CFG_MPTPR;
+
+ memctl->memc_psdmr = psdmr | PSDMR_OP_PREA;
+ *ramaddr = c;
+
+ memctl->memc_psdmr = psdmr | PSDMR_OP_CBRR;
+ for (i = 0; i < 8; i++)
+ *ramaddr = c;
+
+ memctl->memc_psdmr = psdmr | PSDMR_OP_MRW;
+ *ramaddr = c;
+
+ memctl->memc_psdmr = psdmr | PSDMR_OP_NORM | PSDMR_RFEN;
+ *ramaddr = c;
+
+ return (CFG_SDRAM_SIZE << 20);
+}
+
+/* ------------------------------------------------------------------------- */
+/* miscellaneous initialisations after relocation into ram (misc_init_r) */
+/* */
+/* loads the data in the main board and mezzanine board eeproms into */
+/* the hymod configuration struct stored in the board information area. */
+/* */
+/* if the contents of either eeprom is invalid, prompts for a serial */
+/* number (and an ethernet address if required) then fetches a file */
+/* containing information to be stored in the eeprom from the tftp server */
+/* (the file name is based on the serial number and a built-in path) */
+
+/* these are relative to the root of the server's tftp directory */
+static char *bddb_cfgdir = "/hymod/bddb";
+static char *global_env_path = "/hymod/global_env";
+
+static ulong get_serno (const char *prompt)
+{
+ for (;;) {
+ int n;
+ char *p;
+ ulong serno;
+
+ n = readline (prompt);
+
+ if (n < 0)
+ return (0);
+
+ if (n == 0)
+ continue;
+
+ serno = simple_strtol (console_buffer, &p, 10);
+
+ if (p > console_buffer && *p == '\0')
+ return (serno);
+
+ printf ("Invalid number (%s) - please re-enter\n", console_buffer);
+ }
+}
+
+static int read_eeprom (char *label, unsigned offset, hymod_eeprom_t * ep)
+{
+ char filename[50], prompt[50];
+ ulong serno;
+ int count = 0;
+
+ sprintf (prompt, "Enter %s board serial number: ", label);
+
+ for (;;) {
+
+ if (eeprom_load (offset, ep))
+ return (1);
+
+ printf ("*** %s board EEPROM contents are %sinvalid\n",
+ label, count == 0 ? "" : "STILL ");
+
+ puts ("*** will attempt to fetch from server (Ctrl-C to abort)\n");
+
+ if ((serno = get_serno (prompt)) == 0) {
+ puts ("\n*** interrupted! - ignoring eeprom contents\n");
+ return (0);
+ }
+
+ sprintf (filename, "%s/%010lu.cfg", bddb_cfgdir, serno);
+
+ printf ("*** fetching %s board EEPROM contents from server\n",
+ label);
+
+ if (eeprom_fetch (offset, filename, 0x100000) == 0) {
+ puts ("*** fetch failed - ignoring eeprom contents\n");
+ return (0);
+ }
+
+ count++;
+ }
+}
+
+static ulong main_serno;
+
+static int env_fetch_callback (uchar * name, uchar * value)
+{
+ char *ov, nv[CFG_CBSIZE], *p, *q, *nn;
+ int override = 1, append = 0, nl;
+
+ nn = name;
+ if (*nn == '-') {
+ override = 0;
+ nn++;
+ }
+
+ if ((nl = strlen (nn)) > 0 && nn[nl - 1] == '+') {
+ append = 1;
+ nn[--nl] = '\0';
+ }
+
+ p = value;
+ q = nv;
+
+ while ((*q = *p++) != '\0')
+ if (*q == '%') {
+ switch (*p++) {
+
+ case '\0': /* whoops - back up */
+ p--;
+ break;
+
+ case '%': /* a single percent character */
+ q++;
+ break;
+
+ case 's': /* main board serial number as string */
+ q += sprintf (q, "%010lu", main_serno);
+ break;
+
+ case 'S': /* main board serial number as number */
+ q += sprintf (q, "%lu", main_serno);
+ break;
+
+ default: /* ignore any others */
+ break;
+ }
+ } else
+ q++;
+
+ if ((ov = getenv (nn)) != NULL) {
+
+ if (append) {
+
+ if (strstr (ov, nv) == NULL) {
+ int ovl, nvl;
+
+ printf ("Appending '%s' to env cmd '%s'\n", nv, nn);
+
+ ovl = strlen (ov);
+ nvl = strlen (nv);
+
+ while (nvl >= 0) {
+ nv[ovl + 1 + nvl] = nv[nvl];
+ nvl--;
+ }
+
+ nv[ovl] = ' ';
+
+ while (--ovl >= 0)
+ nv[ovl] = ov[ovl];
+
+ setenv (nn, nv);
+ }
+
+ return (1);
+ }
+
+ if (!override || strcmp (ov, nv) == 0)
+ return (1);
+
+ printf ("Re-setting env cmd '%s' from '%s' to '%s'\n", nn, ov, nv);
+ } else
+ printf ("Setting env cmd '%s' to '%s'\n", nn, nv);
+
+ setenv (nn, nv);
+ return (1);
+}
+
+int misc_init_r (void)
+{
+ DECLARE_GLOBAL_DATA_PTR;
+
+ hymod_conf_t *cp = &gd->bd->bi_hymod_conf;
+ int rc;
+
+ memset ((void *) cp, 0, sizeof (*cp));
+
+ /* set up main board config info */
+
+ if (i2c_probe (CFG_I2C_EEPROM_ADDR | HYMOD_EEOFF_MAIN)) {
+
+ if (read_eeprom
+ ("main", HYMOD_EEOFF_MAIN << 8, &cp->main.eeprom))
+ cp->main.eeprom_valid = 1;
+
+ puts ("EEPROM:main...");
+
+ if (cp->main.eeprom_valid) {
+ printf ("OK (ver %u)\n", cp->main.eeprom.ver);
+ eeprom_print (&cp->main.eeprom);
+ main_serno = cp->main.eeprom.serno;
+ } else
+ puts ("BAD\n");
+
+ cp->main.mmap[0].prog.exists = 1;
+ cp->main.mmap[0].prog.size = FPGA_MAIN_CFG_SIZE;
+ cp->main.mmap[0].prog.base = FPGA_MAIN_CFG_BASE;
+
+ cp->main.mmap[0].reg.exists = 1;
+ cp->main.mmap[0].reg.size = FPGA_MAIN_REG_SIZE;
+ cp->main.mmap[0].reg.base = FPGA_MAIN_REG_BASE;
+
+ cp->main.mmap[0].port.exists = 1;
+ cp->main.mmap[0].port.size = FPGA_MAIN_PORT_SIZE;
+ cp->main.mmap[0].port.base = FPGA_MAIN_PORT_BASE;
+
+ cp->main.iopins[0].prog_pin.port = FPGA_MAIN_PROG_PORT;
+ cp->main.iopins[0].prog_pin.pin = FPGA_MAIN_PROG_PIN;
+ cp->main.iopins[0].prog_pin.flag = 1;
+ cp->main.iopins[0].init_pin.port = FPGA_MAIN_INIT_PORT;
+ cp->main.iopins[0].init_pin.pin = FPGA_MAIN_INIT_PIN;
+ cp->main.iopins[0].init_pin.flag = 1;
+ cp->main.iopins[0].done_pin.port = FPGA_MAIN_DONE_PORT;
+ cp->main.iopins[0].done_pin.pin = FPGA_MAIN_DONE_PIN;
+ cp->main.iopins[0].done_pin.flag = 1;
+#ifdef FPGA_MAIN_ENABLE_PORT
+ cp->main.iopins[0].enable_pin.port = FPGA_MAIN_ENABLE_PORT;
+ cp->main.iopins[0].enable_pin.pin = FPGA_MAIN_ENABLE_PIN;
+ cp->main.iopins[0].enable_pin.flag = 1;
+#endif
+ } else
+ puts ("EEPROM:main...NOT PRESENT\n");
+
+ /* set up mezzanine board config info */
+
+ if (i2c_probe (CFG_I2C_EEPROM_ADDR | HYMOD_EEOFF_MEZZ)) {
+
+ if (read_eeprom
+ ("mezz", HYMOD_EEOFF_MEZZ << 8, &cp->mezz.eeprom))
+ cp->mezz.eeprom_valid = 1;
+
+ puts ("EEPROM:mezz...");
+
+ if (cp->mezz.eeprom_valid) {
+ printf ("OK (ver %u)\n", cp->mezz.eeprom.ver);
+ eeprom_print (&cp->mezz.eeprom);
+ } else
+ puts ("BAD\n");
+
+ cp->mezz.mmap[0].prog.exists = 1;
+ cp->mezz.mmap[0].prog.size = FPGA_MEZZ_CFG_SIZE;
+ cp->mezz.mmap[0].prog.base = FPGA_MEZZ_CFG_BASE;
+
+ cp->mezz.mmap[0].reg.exists = 0;
+
+ cp->mezz.mmap[0].port.exists = 0;
+
+ cp->mezz.iopins[0].prog_pin.port = FPGA_MEZZ_PROG_PORT;
+ cp->mezz.iopins[0].prog_pin.pin = FPGA_MEZZ_PROG_PIN;
+ cp->mezz.iopins[0].prog_pin.flag = 1;
+ cp->mezz.iopins[0].init_pin.port = FPGA_MEZZ_INIT_PORT;
+ cp->mezz.iopins[0].init_pin.pin = FPGA_MEZZ_INIT_PIN;
+ cp->mezz.iopins[0].init_pin.flag = 1;
+ cp->mezz.iopins[0].done_pin.port = FPGA_MEZZ_DONE_PORT;
+ cp->mezz.iopins[0].done_pin.pin = FPGA_MEZZ_DONE_PIN;
+ cp->mezz.iopins[0].done_pin.flag = 1;
+#ifdef FPGA_MEZZ_ENABLE_PORT
+ cp->mezz.iopins[0].enable_pin.port = FPGA_MEZZ_ENABLE_PORT;
+ cp->mezz.iopins[0].enable_pin.pin = FPGA_MEZZ_ENABLE_PIN;
+ cp->mezz.iopins[0].enable_pin.flag = 1;
+#endif
+
+ if (cp->mezz.eeprom_valid &&
+ cp->mezz.eeprom.bdtype == HYMOD_BDTYPE_DISPLAY) {
+ /*
+ * mezzanine board is a display board - switch the SEL_CD
+ * input of the FS6377 clock generator (via I/O Port Pin PA11) to
+ * high (or 1) to select the 27MHz required by the display board
+ */
+ iopin_set_high (&pa11);
+
+ puts ("SEL_CD:toggled for display board\n");
+ }
+ } else
+ puts ("EEPROM:mezz...NOT PRESENT\n");
+
+ cp->crc =
+ crc32 (0, (unsigned char *) cp, offsetof (hymod_conf_t, crc));
+
+ if (getenv ("global_env_loaded") == NULL) {
+
+ puts ("*** global environment has not been loaded\n");
+ puts ("*** fetching from server (Control-C to Abort)\n");
+
+ rc = fetch_and_parse (global_env_path, 0x100000,
+ env_fetch_callback);
+
+ if (rc == 0)
+ puts ("*** Fetch of environment failed!\n");
+ else
+ setenv ("global_env_loaded", "yes");
+ }
+ return (0);
+}