diff options
Diffstat (limited to 'board/ti/ti814x/evm.c')
-rw-r--r-- | board/ti/ti814x/evm.c | 67 |
1 files changed, 9 insertions, 58 deletions
diff --git a/board/ti/ti814x/evm.c b/board/ti/ti814x/evm.c index c469645..e406326 100644 --- a/board/ti/ti814x/evm.c +++ b/board/ti/ti814x/evm.c @@ -27,30 +27,10 @@ DECLARE_GLOBAL_DATA_PTR; -#ifdef CONFIG_SPL_BUILD -static struct wd_timer *wdtimer = (struct wd_timer *)WDT_BASE; -#endif - static struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE; /* UART Defines */ #ifdef CONFIG_SPL_BUILD -static void uart_enable(void) -{ - /* UART softreset */ - uart_soft_reset(); -} - -static void wdt_disable(void) -{ - writel(0xAAAA, &wdtimer->wdtwspr); - while (readl(&wdtimer->wdtwwps) != 0x0) - ; - writel(0x5555, &wdtimer->wdtwspr); - while (readl(&wdtimer->wdtwwps) != 0x0) - ; -} - static const struct cmd_control evm_ddr2_cctrl_data = { .cmd0csratio = 0x80, .cmd0dldiff = 0x04, @@ -100,68 +80,39 @@ static const struct ddr_data evm_ddr2_data = { .datauserank0delay = 1, .datadldiff0 = 0x4, }; -#endif -/* - * early system init of muxing and clocks. - */ -void s_init(void) +void set_uart_mux_conf(void) { -#ifdef CONFIG_SPL_BUILD - /* - * Save the boot parameters passed from romcode. - * We cannot delay the saving further than this, - * to prevent overwrites. - */ -#ifdef CONFIG_SPL_BUILD - save_omap_boot_params(); -#endif - - /* WDT1 is already running when the bootloader gets control - * Disable it to avoid "random" resets - */ - wdt_disable(); - - /* Enable timer */ - timer_init(); - - /* Setup the PLLs and the clocks for the peripherals */ - pll_init(); - - /* Enable RTC32K clock */ - rtc32k_enable(); - /* Set UART pins */ enable_uart0_pin_mux(); +} +void set_mux_conf_regs(void) +{ /* Set MMC pins */ enable_mmc1_pin_mux(); /* Set Ethernet pins */ enable_enet_pin_mux(); +} - /* Enable UART */ - uart_enable(); - - gd = &gdata; - - preloader_console_init(); - +void sdram_init(void) +{ config_dmm(&evm_lisa_map_regs); config_ddr(0, 0, &evm_ddr2_data, &evm_ddr2_cctrl_data, &evm_ddr2_emif0_regs, 0); config_ddr(0, 0, &evm_ddr2_data, &evm_ddr2_cctrl_data, &evm_ddr2_emif1_regs, 1); -#endif } +#endif /* * Basic board specific setup. Pinmux has been handled already. */ int board_init(void) { - gd->bd->bi_boot_params = PHYS_DRAM_1 + 0x100; + gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100; return 0; } |