diff options
Diffstat (limited to 'board')
| -rw-r--r-- | board/freescale/common/sys_eeprom.c | 44 | ||||
| -rw-r--r-- | board/freescale/corenet_ds/pci.c | 28 | ||||
| -rw-r--r-- | board/freescale/mpc8569mds/ddr.c | 16 | ||||
| -rw-r--r-- | board/freescale/mpc8569mds/mpc8569mds.c | 26 | ||||
| -rw-r--r-- | board/freescale/mpc8569mds/tlb.c | 15 | ||||
| -rw-r--r-- | board/freescale/p1022ds/p1022ds.c | 67 |
6 files changed, 168 insertions, 28 deletions
diff --git a/board/freescale/common/sys_eeprom.c b/board/freescale/common/sys_eeprom.c index 3929ad0..11dfd84 100644 --- a/board/freescale/common/sys_eeprom.c +++ b/board/freescale/common/sys_eeprom.c @@ -28,13 +28,21 @@ #include <i2c.h> #include <linux/ctype.h> +#ifdef CONFIG_SYS_I2C_EEPROM_CCID #include "../common/eeprom.h" +#define MAX_NUM_PORTS 8 +#endif -#if !defined(CONFIG_SYS_I2C_EEPROM_CCID) && !defined(CONFIG_SYS_I2C_EEPROM_NXID) -#error "Please define either CONFIG_SYS_I2C_EEPROM_CCID or CONFIG_SYS_I2C_EEPROM_NXID" +#ifdef CONFIG_SYS_I2C_EEPROM_NXID +#define MAX_NUM_PORTS 8 +#define NXID_VERSION 0 #endif -#define MAX_NUM_PORTS 8 /* This value must be 8 as defined in doc */ +#ifdef CONFIG_SYS_I2C_EEPROM_NXID_1 +#define CONFIG_SYS_I2C_EEPROM_NXID +#define MAX_NUM_PORTS 23 +#define NXID_VERSION 1 +#endif /** * static eeprom: EEPROM layout for CCID or NXID formats @@ -68,8 +76,8 @@ static struct __attribute__ ((__packed__)) eeprom { u8 res_1[21]; /* 0x2b - 0x3f Reserved */ u8 mac_count; /* 0x40 Number of MAC addresses */ u8 mac_flag; /* 0x41 MAC table flags */ - u8 mac[MAX_NUM_PORTS][6]; /* 0x42 - 0x71 MAC addresses */ - u32 crc; /* 0x72 CRC32 checksum */ + u8 mac[MAX_NUM_PORTS][6]; /* 0x42 - x MAC addresses */ + u32 crc; /* x+1 CRC32 checksum */ #endif } e; @@ -204,7 +212,7 @@ static void update_crc(void) */ static int prog_eeprom(void) { - int ret = 0; /* shut up gcc */ + int ret = 0; int i; void *p; #ifdef CONFIG_SYS_EEPROM_BUS_NUM @@ -225,6 +233,11 @@ static int prog_eeprom(void) i2c_set_bus_num(CONFIG_SYS_EEPROM_BUS_NUM); #endif + /* + * The AT24C02 datasheet says that data can only be written in page + * mode, which means 8 bytes at a time, and it takes up to 5ms to + * complete a given write. + */ for (i = 0, p = &e; i < sizeof(e); i += 8, p += 8) { ret = i2c_write(CONFIG_SYS_I2C_EEPROM_ADDR, i, CONFIG_SYS_I2C_EEPROM_ADDR_LEN, p, min((sizeof(e) - i), 8)); @@ -233,12 +246,23 @@ static int prog_eeprom(void) udelay(5000); /* 5ms write cycle timing */ } + if (!ret) { + /* Verify the write by reading back the EEPROM and comparing */ + struct eeprom e2; + + ret = i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0, + CONFIG_SYS_I2C_EEPROM_ADDR_LEN, (void *)&e2, sizeof(e2)); + if (!ret && memcmp(&e, &e2, sizeof(e))) + ret = -1; + } + #ifdef CONFIG_SYS_EEPROM_BUS_NUM i2c_set_bus_num(bus); #endif if (ret) { printf("Programming failed.\n"); + has_been_read = 0; return -1; } @@ -300,7 +324,7 @@ static void set_mac_address(unsigned int index, const char *string) char *p = (char *) string; unsigned int i; - if (!string) { + if ((index >= MAX_NUM_PORTS) || !string) { printf("Usage: mac <n> XX:XX:XX:XX:XX:XX\n"); return; } @@ -333,7 +357,7 @@ int do_mac(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) if (cmd == 'i') { #ifdef CONFIG_SYS_I2C_EEPROM_NXID memcpy(e.id, "NXID", sizeof(e.id)); - e.version = 0; + e.version = NXID_VERSION; #else memcpy(e.id, "CCID", sizeof(e.id)); #endif @@ -382,8 +406,8 @@ int do_mac(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) e.mac_count = simple_strtoul(argv[2], NULL, 16); update_crc(); break; - case '0' ... '7': /* "mac 0" through "mac 7" */ - set_mac_address(cmd - '0', argv[2]); + case '0' ... '9': /* "mac 0" through "mac 22" */ + set_mac_address(simple_strtoul(argv[1], NULL, 10), argv[2]); break; case 'h': /* help */ default: diff --git a/board/freescale/corenet_ds/pci.c b/board/freescale/corenet_ds/pci.c index 2994e36..e1bca19 100644 --- a/board/freescale/corenet_ds/pci.c +++ b/board/freescale/corenet_ds/pci.c @@ -40,10 +40,14 @@ static struct pci_controller pcie2_hose; static struct pci_controller pcie3_hose; #endif +#ifdef CONFIG_PCIE4 +static struct pci_controller pcie4_hose; +#endif + void pci_init_board(void) { volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); - struct fsl_pci_info pci_info[3]; + struct fsl_pci_info pci_info[4]; u32 devdisr; int first_free_busno = 0; int num = 0; @@ -119,6 +123,28 @@ void pci_init_board(void) #else setbits_be32(&gur->devdisr, FSL_CORENET_DEVDISR_PCIE3); /* disable */ #endif + +#ifdef CONFIG_PCIE4 + pcie_configured = is_serdes_configured(PCIE4); + + if (pcie_configured && !(devdisr & FSL_CORENET_DEVDISR_PCIE4)) { + set_next_law(CONFIG_SYS_PCIE4_MEM_PHYS, LAW_SIZE_512M, + LAW_TRGT_IF_PCIE_4); + set_next_law(CONFIG_SYS_PCIE4_IO_PHYS, LAW_SIZE_64K, + LAW_TRGT_IF_PCIE_4); + SET_STD_PCIE_INFO(pci_info[num], 4); + pcie_ep = fsl_setup_hose(&pcie4_hose, pci_info[num].regs); + printf(" PCIE4 connected to as %s (base addr %lx)\n", + pcie_ep ? "End Point" : "Root Complex", + pci_info[num].regs); + first_free_busno = fsl_pci_init_port(&pci_info[num++], + &pcie4_hose, first_free_busno); + } else { + printf (" PCIE4: disabled\n"); + } +#else + setbits_be32(&gur->devdisr, FSL_CORENET_DEVDISR_PCIE4); /* disable */ +#endif } void pci_of_setup(void *blob, bd_t *bd) diff --git a/board/freescale/mpc8569mds/ddr.c b/board/freescale/mpc8569mds/ddr.c index e938788..e3f5b4a 100644 --- a/board/freescale/mpc8569mds/ddr.c +++ b/board/freescale/mpc8569mds/ddr.c @@ -77,8 +77,18 @@ void fsl_ddr_board_options(memctl_options_t *popts, popts->write_data_delay = 2; /* - * Factors to consider for half-strength driver enable: - * - number of DIMMs installed + * Enable half drive strength */ - popts->half_strength_driver_enable = 0; + popts->half_strength_driver_enable = 1; + + /* Write leveling override */ + popts->wrlvl_en = 1; + popts->wrlvl_override = 1; + popts->wrlvl_sample = 0xa; + popts->wrlvl_start = 0x4; + + /* Rtt and Rtt_W override */ + popts->rtt_override = 1; + popts->rtt_override_value = DDR3_RTT_60_OHM; + popts->rtt_wr_override_value = 0; /* Rtt_WR= dynamic ODT off */ } diff --git a/board/freescale/mpc8569mds/mpc8569mds.c b/board/freescale/mpc8569mds/mpc8569mds.c index 01b7dcb..795e565 100644 --- a/board/freescale/mpc8569mds/mpc8569mds.c +++ b/board/freescale/mpc8569mds/mpc8569mds.c @@ -27,6 +27,7 @@ #include <pci.h> #include <asm/processor.h> #include <asm/mmu.h> +#include <asm/cache.h> #include <asm/immap_85xx.h> #include <asm/fsl_pci.h> #include <asm/fsl_ddr_sdram.h> @@ -211,6 +212,31 @@ int board_early_init_f (void) return 0; } +int board_early_init_r(void) +{ + const unsigned int flashbase = CONFIG_SYS_NAND_BASE; + const u8 flash_esel = 0; + + /* + * Remap Boot flash to caching-inhibited + * so that flash can be erased properly. + */ + + /* Flush d-cache and invalidate i-cache of any FLASH data */ + flush_dcache(); + invalidate_icache(); + + /* invalidate existing TLB entry for flash */ + disable_tlb(flash_esel); + + set_tlb(1, flashbase, CONFIG_SYS_NAND_BASE, /* tlb, epn, rpn */ + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, /* perms, wimge */ + 0, flash_esel, /* ts, esel */ + BOOKE_PAGESZ_64M, 1); /* tsize, iprot */ + + return 0; +} + int checkboard (void) { printf ("Board: 8569 MDS\n"); diff --git a/board/freescale/mpc8569mds/tlb.c b/board/freescale/mpc8569mds/tlb.c index 73dcc3e..f852fc3 100644 --- a/board/freescale/mpc8569mds/tlb.c +++ b/board/freescale/mpc8569mds/tlb.c @@ -1,5 +1,5 @@ /* - * Copyright 2009 Freescale Semiconductor, Inc. + * Copyright 2009-2010 Freescale Semiconductor, Inc. * * (C) Copyright 2000 * Wolfgang Denk, DENX Software Engineering, wd@denx.de. @@ -46,15 +46,20 @@ struct fsl_e_tlb_entry tlb_table[] = { /* TLB 1 Initializations */ /* - * TLBe 0: 64M Non-cacheable, guarded + * TLBe 0: 64M write-through, guarded * Out of reset this entry is only 4K. - * 0xfc000000 256K NAND FLASH (CS3) - * 0xfe000000 32M NOR FLASH (CS0) + * 0xfc000000 32MB NAND FLASH (CS3) + * 0xfe000000 32MB NOR FLASH (CS0) */ +#ifdef CONFIG_NAND_SPL SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE, MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 0, BOOKE_PAGESZ_1M, 1), +#else + SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_W|MAS2_G, 0, 0, BOOKE_PAGESZ_64M, 1), - +#endif /* * TLBe 1: 256KB Non-cacheable, guarded * 0xf8000000 32K BCSR diff --git a/board/freescale/p1022ds/p1022ds.c b/board/freescale/p1022ds/p1022ds.c index 5cdee9f..ee93e8b 100644 --- a/board/freescale/p1022ds/p1022ds.c +++ b/board/freescale/p1022ds/p1022ds.c @@ -27,6 +27,7 @@ #include <asm/mp.h> #include <netdev.h> #include <i2c.h> +#include <hwconfig.h> #include "../common/ngpixis.h" @@ -90,34 +91,58 @@ phys_size_t initdram(int board_type) #define CONFIG_TFP410_I2C_ADDR 0x38 +/* Masks for the SSI_TDM and AUDCLK bits of the ngPIXIS BRDCFG1 register. */ +#define CONFIG_PIXIS_BRDCFG1_SSI_TDM_MASK 0x0c +#define CONFIG_PIXIS_BRDCFG1_AUDCLK_MASK 0x03 + +/* Route the I2C1 pins to the SSI port instead. */ +#define CONFIG_PIXIS_BRDCFG1_SSI_TDM_SSI 0x08 + +/* Choose the 12.288Mhz codec reference clock */ +#define CONFIG_PIXIS_BRDCFG1_AUDCLK_12 0x02 + +/* Choose the 11.2896Mhz codec reference clock */ +#define CONFIG_PIXIS_BRDCFG1_AUDCLK_11 0x01 + int misc_init_r(void) { u8 temp; + const char *audclk; + size_t arglen; - /* Enable the TFP410 Encoder */ + /* For DVI, enable the TFP410 Encoder. */ temp = 0xBF; if (i2c_write(CONFIG_TFP410_I2C_ADDR, 0x08, 1, &temp, sizeof(temp)) < 0) return -1; - - /* Verify if enabled */ - temp = 0; if (i2c_read(CONFIG_TFP410_I2C_ADDR, 0x08, 1, &temp, sizeof(temp)) < 0) return -1; - debug("DVI Encoder Read: 0x%02x\n", temp); temp = 0x10; if (i2c_write(CONFIG_TFP410_I2C_ADDR, 0x0A, 1, &temp, sizeof(temp)) < 0) return -1; - - /* Verify if enabled */ - temp = 0; if (i2c_read(CONFIG_TFP410_I2C_ADDR, 0x0A, 1, &temp, sizeof(temp)) < 0) return -1; - debug("DVI Encoder Read: 0x%02x\n",temp); + /* + * Enable the reference clock for the WM8776 codec, and route the MUX + * pins for SSI. The default is the 12.288 MHz clock + */ + + temp = in_8(&pixis->brdcfg1) & ~(CONFIG_PIXIS_BRDCFG1_SSI_TDM_MASK | + CONFIG_PIXIS_BRDCFG1_AUDCLK_MASK); + temp |= CONFIG_PIXIS_BRDCFG1_SSI_TDM_SSI; + + audclk = hwconfig_arg("audclk", &arglen); + /* Check the first two chars only */ + if (audclk && (strncmp(audclk, "11", 2) == 0)) + temp |= CONFIG_PIXIS_BRDCFG1_AUDCLK_11; + else + temp |= CONFIG_PIXIS_BRDCFG1_AUDCLK_12; + out_8(&pixis->brdcfg1, temp); + return 0; } @@ -310,6 +335,27 @@ int board_eth_init(bd_t *bis) } #ifdef CONFIG_OF_BOARD_SETUP +/** + * ft_codec_setup - fix up the clock-frequency property of the codec node + * + * Update the clock-frequency property based on the value of the 'audclk' + * hwconfig option. If audclk is not specified, then default to 12.288MHz. + */ +static void ft_codec_setup(void *blob, const char *compatible) +{ + const char *audclk; + size_t arglen; + u32 freq; + + audclk = hwconfig_arg("audclk", &arglen); + if (audclk && (strncmp(audclk, "11", 2) == 0)) + freq = 11289600; + else + freq = 12288000; + + do_fixup_by_compat_u32(blob, compatible, "clock-frequency", freq, 1); +} + void ft_board_setup(void *blob, bd_t *bd) { phys_addr_t base; @@ -327,6 +373,9 @@ void ft_board_setup(void *blob, bd_t *bd) #ifdef CONFIG_FSL_SGMII_RISER fsl_sgmii_riser_fdt_fixup(blob); #endif + + /* Update the WM8776 node's clock frequency property */ + ft_codec_setup(blob, "wlf,wm8776"); } #endif |