summaryrefslogtreecommitdiff
path: root/board
diff options
context:
space:
mode:
Diffstat (limited to 'board')
-rw-r--r--board/amcc/bamboo/bamboo.c57
1 files changed, 38 insertions, 19 deletions
diff --git a/board/amcc/bamboo/bamboo.c b/board/amcc/bamboo/bamboo.c
index d02add5..53bf735 100644
--- a/board/amcc/bamboo/bamboo.c
+++ b/board/amcc/bamboo/bamboo.c
@@ -31,6 +31,8 @@ void ext_bus_cntlr_init(void);
void configure_ppc440ep_pins(void);
int is_nand_selected(void);
+unsigned char cfg_simulate_spd_eeprom[128];
+
gpio_param_s gpio_tab[GPIO_GROUP_MAX][GPIO_MAX];
#if 0
{ /* GPIO Alternate1 Alternate2 Alternate3 */
@@ -380,7 +382,7 @@ int checkboard(void)
/*************************************************************************
*
- * fixed_sdram_init -- Bamboo has one bank onboard sdram (plus DIMM)
+ * init_spd_array -- Bamboo has one bank onboard sdram (plus DIMM)
*
* Fixed memory is composed of :
* MT46V16M16TG-75 from Micron (x 2), 256Mb, 16 M x16, DDR266,
@@ -397,24 +399,40 @@ int checkboard(void)
* PLB @ 133 MHz
*
************************************************************************/
-void fixed_sdram_init(void)
+static void init_spd_array(void)
{
- /*
- * clear this first, if the DDR is enabled by a debugger
- * then you can not make changes.
- */
- mtsdram(mem_cfg0, 0x00000000); /* Disable EEC */
+ cfg_simulate_spd_eeprom[8] = 0x04; /* 2.5 Volt */
+ cfg_simulate_spd_eeprom[2] = 0x07; /* DDR ram */
- /*--------------------------------------------------------------------
- * Setup for board-specific specific mem
- *------------------------------------------------------------------*/
- /*
- * Following for CAS Latency = 2.5 @ 133 MHz PLB
- */
- mtsdram(mem_b0cr, 0x00082001);
- mtsdram(mem_b1cr, 0x00000000);
- mtsdram(mem_b2cr, 0x00000000);
- mtsdram(mem_b3cr, 0x00000000);
+#ifdef CONFIG_DDR_ECC
+ cfg_simulate_spd_eeprom[11] = 0x02; /* ECC ON : 02 OFF : 00 */
+ cfg_simulate_spd_eeprom[31] = 0x08; /* bankSizeID: 32MB */
+ cfg_simulate_spd_eeprom[3] = 0x0C; /* num Row Addr: 12 */
+#else
+ cfg_simulate_spd_eeprom[11] = 0x00; /* ECC ON : 02 OFF : 00 */
+ cfg_simulate_spd_eeprom[31] = 0x10; /* bankSizeID: 64MB */
+ cfg_simulate_spd_eeprom[3] = 0x0D; /* num Row Addr: 13 */
+#endif
+
+ cfg_simulate_spd_eeprom[4] = 0x09; /* numColAddr: 9 */
+ cfg_simulate_spd_eeprom[5] = 0x01; /* numBanks: 1 */
+ cfg_simulate_spd_eeprom[0] = 0x80; /* number of SPD bytes used: 128 */
+ cfg_simulate_spd_eeprom[1] = 0x08; /* total number bytes in SPD device = 256 */
+ cfg_simulate_spd_eeprom[21] = 0x00; /* not registered: 0 registered : 0x02*/
+ cfg_simulate_spd_eeprom[6] = 0x20; /* Module data width: 32 bits */
+ cfg_simulate_spd_eeprom[7] = 0x00; /* Module data width continued: +0 */
+ cfg_simulate_spd_eeprom[15] = 0x01; /* wcsbc = 1 */
+ cfg_simulate_spd_eeprom[27] = 0x50; /* tRpNs = 20 ns */
+ cfg_simulate_spd_eeprom[29] = 0x50; /* tRcdNs = 20 ns */
+
+ cfg_simulate_spd_eeprom[30] = 45; /* tRasNs */
+
+ cfg_simulate_spd_eeprom[18] = 0x0C; /* casBit (2,2.5) */
+
+ cfg_simulate_spd_eeprom[9] = 0x75; /* SDRAM Cycle Time (cas latency 2.5) = 7.5 ns */
+ cfg_simulate_spd_eeprom[23] = 0xA0; /* SDRAM Cycle Time (cas latency 2) = 10 ns */
+ cfg_simulate_spd_eeprom[25] = 0x00; /* SDRAM Cycle Time (cas latency 1.5) = N.A */
+ cfg_simulate_spd_eeprom[12] = 0x82; /* refresh Rate Type: Normal (15.625us) + Self refresh */
}
long int initdram (int board_type)
@@ -422,9 +440,10 @@ long int initdram (int board_type)
long dram_size = 0;
/*
- * First init bank0 (onboard sdram) and then configure the DIMM-slots
+ * First write simulated values in eeprom array for onboard bank 0
*/
- fixed_sdram_init();
+ init_spd_array();
+
dram_size = spd_sdram (0);
return dram_size;