summaryrefslogtreecommitdiff
path: root/doc/README.PIP405
diff options
context:
space:
mode:
Diffstat (limited to 'doc/README.PIP405')
-rw-r--r--doc/README.PIP40538
1 files changed, 15 insertions, 23 deletions
diff --git a/doc/README.PIP405 b/doc/README.PIP405
index 610ff21..d8b3f9c 100644
--- a/doc/README.PIP405
+++ b/doc/README.PIP405
@@ -100,9 +100,9 @@ CONFIG_ATAPI enables ATAPI Support
SCSI support (experimental) only SYM53C8xx supported
----------------------------------------------------
CONFIG_SCSI_SYM53C8XX type of SCSI controller
-CFG_SCSI_MAX_LUN 8 number of supported LUNs
-CFG_SCSI_MAX_SCSI_ID 7 maximum SCSI ID (0..6)
-CFG_SCSI_MAX_DEVICE CFG_SCSI_MAX_SCSI_ID * CFG_SCSI_MAX_LUN
+CONFIG_SYS_SCSI_MAX_LUN 8 number of supported LUNs
+CONFIG_SYS_SCSI_MAX_SCSI_ID 7 maximum SCSI ID (0..6)
+CONFIG_SYS_SCSI_MAX_DEVICE CONFIG_SYS_SCSI_MAX_SCSI_ID * CONFIG_SYS_SCSI_MAX_LUN
maximum of Target devices (multiple LUN support
for boot)
@@ -125,32 +125,24 @@ CONFIG_VIDEO_CT69000 Enable Chips & Technologies 69000 Video chip
External peripheral base address:
---------------------------------
-CFG_ISA_IO_BASE_ADDRESS address of all ISA-bus related parts
+CONFIG_SYS_ISA_IO_BASE_ADDRESS address of all ISA-bus related parts
_must_ be defined for ISA-bus parts
Identify:
---------
CONFIG_IDENT_STRING added to the U_BOOT_VERSION String
-
-I2C stuff:
-----------
-CFG_EEPROM_PAGE_WRITE_ENABLE enables page write of the I2C EEPROM
- CFG_EEPROM_PAGE_WRITE_BITS _must_ be
- defined.
-
-
Environment / Console:
----------------------
-CFG_CONSOLE_IS_IN_ENV if defined, stdin, stdout and stderr used from
+CONFIG_SYS_CONSOLE_IS_IN_ENV if defined, stdin, stdout and stderr used from
the values stored in the evironment.
-CFG_CONSOLE_OVERWRITE_ROUTINE if defined, console_overwrite() decides if the
+CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE if defined, console_overwrite() decides if the
values stored in the environment or the standard
serial in/out put should be assigned to the console.
-CFG_CONSOLE_ENV_OVERWRITE if defined, the start-up console switching
+CONFIG_SYS_CONSOLE_ENV_OVERWRITE if defined, the start-up console switching
are stored in the environment.
PIP405 specific:
@@ -169,7 +161,7 @@ Added Devices:
Floppy support:
---------------
-Support of a standard floppy disk controller at address CFG_ISA_IO_BASE_ADDRESS
+Support of a standard floppy disk controller at address CONFIG_SYS_ISA_IO_BASE_ADDRESS
+ 0x3F0. Enabled with define CONFIG_CMD_FDC. Reads a unformated floppy disk
with a image header (see: mkimage). No interrupts and no DMA are used for this.
Added files:
@@ -181,7 +173,7 @@ SCSI support:
Support for Symbios SYM53C810A chip. Implemented as follows:
- without disconnect
- only asynchrounous
-- multiple LUN support (caution, needs a lot of RAM. define CFG_SCSI_MAX_LUN 1 to
+- multiple LUN support (caution, needs a lot of RAM. define CONFIG_SYS_SCSI_MAX_LUN 1 to
save RAM)
- multiple SCSI ID support
- no write support
@@ -205,7 +197,7 @@ ATAPI support (IDE changes):
----------------------------
Added ATAPI support (with CONFIG_ATAPI) in the file cmd_ide.c.
To support a hardreset, when the IDE reset pin is not connected to the
-CFG_PC_IDE_RESET pin, the switch CONFIG_IDE_RESET_ROUTINE has been added. When
+CONFIG_SYS_PC_IDE_RESET pin, the switch CONFIG_IDE_RESET_ROUTINE has been added. When
this switch is enabled the routine void ide_set_reset(int idereset) must be
within the board specific files.
Only read from ATAPI devices are supported.
@@ -250,7 +242,7 @@ changed files:
MC146818 RTC support:
---------------------
Added support for MC146818 RTC with defining CONFIG_RTC_MC146818. The ISA bus IO
-base address must be defined with CFG_ISA_IO_BASE_ADDRESS.
+base address must be defined with CONFIG_SYS_ISA_IO_BASE_ADDRESS.
Added files:
- rtc/mc146818.c
@@ -307,7 +299,7 @@ I2C Stuff:
----------
Added defined(CONFIG_PIP405) at several points in common/cmd_i2c.c.
Added 16bit read/write support for I2C (PPC405), and page write to
-I2C EEPROM if defined CFG_EEPROM_PAGE_WRITE_ENABLE.
+I2C EEPROM if defined CONFIG_SYS_EEPROM_PAGE_WRITE_ENABLE.
Changed files:
- cpu/ppc4xx/i2c.c
- common/cmd_i2c.c
@@ -316,11 +308,11 @@ Environment / Console:
----------------------
Although in README.console described, the U-Boot has not assinged the values
found in the environment to the console. Corrected this behavior, but only if
-CFG_CONSOLE_IS_IN_ENV is defined.
-If CFG_CONSOLE_OVERWRITE_ROUTINE is defined, console_overwrite() decides if the
+CONFIG_SYS_CONSOLE_IS_IN_ENV is defined.
+If CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE is defined, console_overwrite() decides if the
values stored in the environment or the standard serial in/output should be
assigned to the console. This is useful if the environment values are not correct.
-If CFG_CONSOLE_ENV_OVERWRITE is defined the devices assigned to the console at
+If CONFIG_SYS_CONSOLE_ENV_OVERWRITE is defined the devices assigned to the console at
start-up time will be written to the environment. This means that if the
environment values are overwritten by the overwrite_console() routine, they will be
stored in the environment.