summaryrefslogtreecommitdiff
path: root/doc/README.m5475evb
diff options
context:
space:
mode:
Diffstat (limited to 'doc/README.m5475evb')
-rw-r--r--doc/README.m5475evb54
1 files changed, 27 insertions, 27 deletions
diff --git a/doc/README.m5475evb b/doc/README.m5475evb
index 37d1438..dc9a605 100644
--- a/doc/README.m5475evb
+++ b/doc/README.m5475evb
@@ -74,20 +74,20 @@ CONFIG_M547x -- define for all Freescale MCF547x CPUs
CONFIG_M5475 -- define for M5475EVB board
CONFIG_MCFUART -- define to use common CF Uart driver
-CFG_UART_PORT -- define UART port number, start with 0, 1 and 2
+CONFIG_SYS_UART_PORT -- define UART port number, start with 0, 1 and 2
CONFIG_BAUDRATE -- define UART baudrate
CONFIG_FSLDMAFEC -- define to use common dma FEC driver
CONFIG_NET_MULTI -- define to use multi FEC in u-boot
CONFIG_MII -- enable to use MII driver
CONFIG_CF_DOMII -- enable to use MII feature in cmd_mii.c
-CFG_DISCOVER_PHY -- enable PHY discovery
-CFG_RX_ETH_BUFFER -- Set FEC Receive buffer
-CFG_FAULT_ECHO_LINK_DOWN--
-CFG_FEC0_PINMUX -- Set FEC0 Pin configuration
-CFG_FEC1_PINMUX -- Set FEC1 Pin configuration
-CFG_FEC0_MIIBASE -- Set FEC0 MII base register
-CFG_FEC1_MIIBASE -- Set FEC0 MII base register
+CONFIG_SYS_DISCOVER_PHY -- enable PHY discovery
+CONFIG_SYS_RX_ETH_BUFFER -- Set FEC Receive buffer
+CONFIG_SYS_FAULT_ECHO_LINK_DOWN--
+CONFIG_SYS_FEC0_PINMUX -- Set FEC0 Pin configuration
+CONFIG_SYS_FEC1_PINMUX -- Set FEC1 Pin configuration
+CONFIG_SYS_FEC0_MIIBASE -- Set FEC0 MII base register
+CONFIG_SYS_FEC1_MIIBASE -- Set FEC0 MII base register
MCFFEC_TOUT_LOOP -- set FEC timeout loop
CONFIG_HAS_ETH1 -- define to enable second FEC in u-boot
@@ -101,35 +101,35 @@ CONFIG_SLTTMR -- define to use SLT timer
CONFIG_FSL_I2C -- define to use FSL common I2C driver
CONFIG_HARD_I2C -- define for I2C hardware support
CONFIG_SOFT_I2C -- define for I2C bit-banged
-CFG_I2C_SPEED -- define for I2C speed
-CFG_I2C_SLAVE -- define for I2C slave address
-CFG_I2C_OFFSET -- define for I2C base address offset
-CFG_IMMR -- define for MBAR offset
+CONFIG_SYS_I2C_SPEED -- define for I2C speed
+CONFIG_SYS_I2C_SLAVE -- define for I2C slave address
+CONFIG_SYS_I2C_OFFSET -- define for I2C base address offset
+CONFIG_SYS_IMMR -- define for MBAR offset
CONFIG_PCI -- define for PCI support
CONFIG_PCI_PNP -- define for Plug n play support
CONFIG_SKIPPCI_HOSTBRIDGE -- SKIP PCI Host bridge
-CFG_PCI_MEM_BUS -- PCI memory logical offset
-CFG_PCI_MEM_PHYS -- PCI memory physical offset
-CFG_PCI_MEM_SIZE -- PCI memory size
-CFG_PCI_IO_BUS -- PCI IO logical offset
-CFG_PCI_IO_PHYS -- PCI IO physical offset
-CFG_PCI_IO_SIZE -- PCI IO size
-CFG_PCI_CFG_BUS -- PCI Configuration logical offset
-CFG_PCI_CFG_PHYS -- PCI Configuration physical offset
-CFG_PCI_CFG_SIZE -- PCI Configuration size
+CONFIG_SYS_PCI_MEM_BUS -- PCI memory logical offset
+CONFIG_SYS_PCI_MEM_PHYS -- PCI memory physical offset
+CONFIG_SYS_PCI_MEM_SIZE -- PCI memory size
+CONFIG_SYS_PCI_IO_BUS -- PCI IO logical offset
+CONFIG_SYS_PCI_IO_PHYS -- PCI IO physical offset
+CONFIG_SYS_PCI_IO_SIZE -- PCI IO size
+CONFIG_SYS_PCI_CFG_BUS -- PCI Configuration logical offset
+CONFIG_SYS_PCI_CFG_PHYS -- PCI Configuration physical offset
+CONFIG_SYS_PCI_CFG_SIZE -- PCI Configuration size
-CFG_MBAR -- define MBAR offset
+CONFIG_SYS_MBAR -- define MBAR offset
CONFIG_MONITOR_IS_IN_RAM -- Not support
-CFG_INIT_RAM_ADDR -- defines the base address of the MCF547x internal SRAM
+CONFIG_SYS_INIT_RAM_ADDR -- defines the base address of the MCF547x internal SRAM
-CFG_CSn_BASE -- defines the Chip Select Base register
-CFG_CSn_MASK -- defines the Chip Select Mask register
-CFG_CSn_CTRL -- defines the Chip Select Control register
+CONFIG_SYS_CSn_BASE -- defines the Chip Select Base register
+CONFIG_SYS_CSn_MASK -- defines the Chip Select Mask register
+CONFIG_SYS_CSn_CTRL -- defines the Chip Select Control register
-CFG_SDRAM_BASE -- defines the DRAM Base
+CONFIG_SYS_SDRAM_BASE -- defines the DRAM Base
2. MEMORY MAP UNDER U-BOOT AND LINUX KERNEL
===========================================