summaryrefslogtreecommitdiff
path: root/doc/README.mpc8536ds
diff options
context:
space:
mode:
Diffstat (limited to 'doc/README.mpc8536ds')
-rw-r--r--doc/README.mpc8536ds127
1 files changed, 0 insertions, 127 deletions
diff --git a/doc/README.mpc8536ds b/doc/README.mpc8536ds
deleted file mode 100644
index 2a38bd6..0000000
--- a/doc/README.mpc8536ds
+++ /dev/null
@@ -1,127 +0,0 @@
-Overview:
-=========
-
-The MPC8536E integrates a PowerPC processor core with system logic
-required for imaging, networking, and communications applications.
-
-Boot from NAND:
-===============
-
-The MPC8536E is capable of booting from NAND flash which uses the image
-u-boot-nand.bin. This image contains two parts: a first stage image(also
-call 4K NAND loader and a second stage image. The former is appended to
-the latter to produce u-boot-nand.bin.
-
-The bootup process can be divided into two stages: the first stage will
-configure the L2SRAM, then copy the second stage image to L2SRAM and jump
-to it. The second stage image is to configure all the hardware and boot up
-to U-Boot command line.
-
-The 4K NAND loader's code comes from the corresponding nand_spl directory,
-along with the code twisted by CONFIG_NAND_SPL. The macro CONFIG_NAND_SPL
-is mainly used to shrink the code size to the 4K size limitation.
-
-The macro CONFIG_SYS_RAMBOOT is used to control the code to produce the
-second stage image. It's set in the board config file when boot from NAND
-is selected.
-
-Build and boot steps
---------------------
-
-1. Building image
- make MPC8536DS_NAND_config
- make CROSS_COMPILE=powerpc-none-linux-gnuspe- all
-
-2. Change dip-switch
- SW2[5-8] = 1011
- SW9[1-3] = 101
- Note: 1 stands for 'on', 0 stands for 'off'
-
-3. Flash image
- tftp 1000000 u-boot-nand.bin
- nand erase 0 a0000
- nand write 1000000 0 a0000
-
-Boot from On-chip ROM:
-======================
-
-The MPC8536E is capable of booting from the on-chip ROM - boot from eSDHC
-and boot from eSPI. When power on, the porcessor excutes the ROM code to
-initialize the eSPI/eSDHC controller, and loads the mian U-Boot image from
-the memory device that interfaced to the controller, such as the SDCard or
-SPI EEPROM, to the target memory, e.g. SDRAM or L2SRAM, then boot from it.
-
-The memory device should contain a specific data structure with control word
-and config word at the fixed address. The config word direct the process how
-to config the memory device, and the control word direct the processor where
-to find the image on the memory device, or where copy the main image to. The
-user can use any method to store the data structure to the memory device, only
-if store it on the assigned address.
-
-Build and boot steps
---------------------
-
-For boot from eSDHC:
-1. Build image
- make MPC8536DS_SDCARD_config
- make CROSS_COMPILE=powerpc-none-linux-gnuspe- all
-
-2. Change dip-switch
- SW2[5-8] = 0111
- SW3[1] = 0
- SW8[7] = 0 - The on-board SD/MMC slot is active
- SW8[7] = 1 - The externel SD/MMC slot is active
-
-3. Put image to SDCard
- Put the follwing info at the assigned address on the SDCard:
-
- Offset | Data | Description
- --------------------------------------------------------
- | 0x40-0x43 | 0x424F4F54 | BOOT signature |
- --------------------------------------------------------
- | 0x48-0x4B | 0x00080000 | u-boot.bin's size |
- --------------------------------------------------------
- | 0x50-0x53 | 0x???????? | u-boot.bin's Addr on SDCard |
- --------------------------------------------------------
- | 0x58-0x5B | 0xF8F80000 | Target Address |
- -------------------------------------------------------
- | 0x60-0x63 | 0xF8FFF000 | Execution Starting Address |
- --------------------------------------------------------
- | 0x68-0x6B | 0x6 | Number of Config Addr/Data |
- --------------------------------------------------------
- | 0x80-0x83 | 0xFF720100 | Config Addr 1 |
- | 0x84-0x87 | 0xF8F80000 | Config Data 1 |
- --------------------------------------------------------
- | 0x88-0x8b | 0xFF720e44 | Config Addr 2 |
- | 0x8c-0x8f | 0x0000000C | Config Data 2 |
- --------------------------------------------------------
- | 0x90-0x93 | 0xFF720000 | Config Addr 3 |
- | 0x94-0x97 | 0x80010000 | Config Data 3 |
- --------------------------------------------------------
- | 0x98-0x9b | 0xFF72e40c | Config Addr 4 |
- | 0x9c-0x9f | 0x00000040 | Config Data 4 |
- --------------------------------------------------------
- | 0xa0-0xa3 | 0x40000001 | Config Addr 5 |
- | 0xa4-0xa7 | 0x00000100 | Config Data 5 |
- --------------------------------------------------------
- | 0xa8-0xab | 0x80000001 | Config Addr 6 |
- | 0xac-0xaf | 0x80000001 | Config Data 6 |
- --------------------------------------------------------
- | ...... |
- --------------------------------------------------------
- | 0x???????? | u-boot.bin |
- --------------------------------------------------------
-
- then insert the SDCard to the active slot to boot up.
-
-For boot from eSPI:
-1. Build image
- make MPC8536DS_SPIFLASH_config
- make CROSS_COMPILE=powerpc-none-linux-gnuspe- all
-
-2. Change dip-switch
- SW2[5-8] = 0110
-
-3. Put image to SPI flash
- Put the info in the above table onto the SPI flash, then
- boot up.