summaryrefslogtreecommitdiff
path: root/doc/README.mpc8641hpcn
diff options
context:
space:
mode:
Diffstat (limited to 'doc/README.mpc8641hpcn')
-rw-r--r--doc/README.mpc8641hpcn106
1 files changed, 66 insertions, 40 deletions
diff --git a/doc/README.mpc8641hpcn b/doc/README.mpc8641hpcn
index 1c41d77..d8fe0a4 100644
--- a/doc/README.mpc8641hpcn
+++ b/doc/README.mpc8641hpcn
@@ -21,16 +21,16 @@ Jumpers:
J14 Pins 1-2 (near plcc32 socket)
Switches:
- SW1(1-5) = 01100 CFG_COREPLL = 01000 :: CORE = 2:1
+ SW1(1-5) = 01100 CONFIG_SYS_COREPLL = 01000 :: CORE = 2:1
01100 :: CORE = 2.5:1
10000 :: CORE = 3:1
11100 :: CORE = 3.5:1
10100 :: CORE = 4:1
01110 :: CORE = 4.5:1
- SW1(6-8) = 001 CFG_SYSCLK = 000 :: SYSCLK = 33MHz
+ SW1(6-8) = 001 CONFIG_SYS_SYSCLK = 000 :: SYSCLK = 33MHz
001 :: SYSCLK = 40MHz
- SW2(1-4) = 1100 CFG_CCBPLL = 0010 :: 2X
+ SW2(1-4) = 1100 CONFIG_SYS_CCBPLL = 0010 :: 2X
0100 :: 4X
0110 :: 6X
1000 :: 8X
@@ -38,34 +38,34 @@ Switches:
1100 :: 12X
1110 :: 14X
0000 :: 16X
- SW2(5-8) = 1110 CFG_BOOTLOC = 1110 :: boot 16-bit localbus
+ SW2(5-8) = 1110 CONFIG_SYS_BOOTLOC = 1110 :: boot 16-bit localbus
- SW3(1-7) = 0011000 CFG_VID = 0011000 :: VCORE = 1.2V
+ SW3(1-7) = 0011000 CONFIG_SYS_VID = 0011000 :: VCORE = 1.2V
0100000 :: VCORE = 1.11V
SW3(8) = 0 VCC_PLAT = 0 :: VCC_PLAT = 1.2V
1 :: VCC_PLAT = 1.0V
- SW4(1-2) = 11 CFG_HOSTMODE = 11 :: both prots host/root
- SW4(3-4) = 11 CFG_BOOTSEQ = 11 :: no boot seq
- SW4(5-8) = 0011 CFG_IOPORT = 0011 :: both PEX
+ SW4(1-2) = 11 CONFIG_SYS_HOSTMODE = 11 :: both prots host/root
+ SW4(3-4) = 11 CONFIG_SYS_BOOTSEQ = 11 :: no boot seq
+ SW4(5-8) = 0011 CONFIG_SYS_IOPORT = 0011 :: both PEX
- SW5(1) = 1 CFG_FLASHMAP = 1 :: boot from flash
+ SW5(1) = 1 CONFIG_SYS_FLASHMAP = 1 :: boot from flash
0 :: boot from PromJet
- SW5(2) = 1 CFG_FLASHBANK = 1 :: swap upper/lower
+ SW5(2) = 1 CONFIG_SYS_FLASHBANK = 1 :: swap upper/lower
halves (virtual banks)
0 :: normal
- SW5(3) = 0 CFG_FLASHWP = 0 :: not protected
- SW5(4) = 0 CFG_PORTDIV = 1 :: 2:1 for PD4
+ SW5(3) = 0 CONFIG_SYS_FLASHWP = 0 :: not protected
+ SW5(4) = 0 CONFIG_SYS_PORTDIV = 1 :: 2:1 for PD4
1:1 for PD6
- SW5(5-6) = 11 CFG_PIXISOPT = 11 :: s/w determined
- SW5(7-8) = 11 CFG_LADOPT = 11 :: s/w determined
+ SW5(5-6) = 11 CONFIG_SYS_PIXISOPT = 11 :: s/w determined
+ SW5(7-8) = 11 CONFIG_SYS_LADOPT = 11 :: s/w determined
- SW6(1) = 1 CFG_CPUBOOT = 1 :: no boot holdoff
- SW6(2) = 1 CFG_BOOTADDR = 1 :: no traslation
- SW6(3-5) = 000 CFG_REFCLKSEL = 000 :: 100MHZ
- SW6(6) = 1 CFG_SERROM_ADDR= 1 ::
- SW6(7) = 1 CFG_MEMDEBUG = 1 ::
- SW6(8) = 1 CFG_DDRDEBUG = 1 ::
+ SW6(1) = 1 CONFIG_SYS_CPUBOOT = 1 :: no boot holdoff
+ SW6(2) = 1 CONFIG_SYS_BOOTADDR = 1 :: no traslation
+ SW6(3-5) = 000 CONFIG_SYS_REFCLKSEL = 000 :: 100MHZ
+ SW6(6) = 1 CONFIG_SYS_SERROM_ADDR= 1 ::
+ SW6(7) = 1 CONFIG_SYS_MEMDEBUG = 1 ::
+ SW6(8) = 1 CONFIG_SYS_DDRDEBUG = 1 ::
SW8(1) = 1 ACZ_SYNC = 1 :: 48MHz on TP49
SW8(2) = 1 ACB_SYNC = 1 :: THRMTRIP disabled
@@ -74,56 +74,82 @@ Switches:
SW8(5) = 0 SUSLED = 0 :: SouthBridge Mode
SW8(6) = 0 SPREAD = 0 :: REFCLK SSCG Disabled
SW8(7) = 1 ACPWR = 1 :: non-battery
- SW8(8) = 0 CFG_IDWP = 0 :: write enable
+ SW8(8) = 0 CONFIG_SYS_IDWP = 0 :: write enable
3. Flash U-Boot
---------------
-The flash range 0xFF800000 to 0xFFFFFFFF can be divided into 2 halves.
+The flash range 0xEF800000 to 0xEFFFFFFF can be divided into 2 halves.
It is possible to use either half to boot using u-boot. Switch 5 bit 2
is used for this purpose.
-0xFF800000 to 0xFFBFFFFF - 4MB
-0xFFC00000 to 0xFFFFFFFF - 4MB
-When this bit is 0, U-Boot is at 0xFFF00000.
-When this bit is 1, U-Boot is at 0xFFB00000.
+0xEF800000 to 0xEFBFFFFF - 4MB
+0xEFC00000 to 0xEFFFFFFF - 4MB
+When this bit is 0, U-Boot is at 0xEFF00000.
+When this bit is 1, U-Boot is at 0xEFB00000.
Use the above mentioned flash commands to program the other half, and
use switch 5, bit 2 to alternate between the halves. Note: The booting
-version of U-Boot will always be at 0xFFF00000.
+version of U-Boot will always be at 0xEFF00000.
-To Flash U-Boot into the booting bank (0xFFC00000 - 0xFFFFFFFF):
+To Flash U-Boot into the booting bank (0xEFC00000 - 0xEFFFFFFF):
tftp 1000000 u-boot.bin
protect off all
- erase fff00000 +$filesize
- cp.b 1000000 fff00000 $filesize
+ erase eff00000 +$filesize
+ cp.b 1000000 eff00000 $filesize
or use tftpflash command:
run tftpflash
-To Flash U-boot into the alternative bank (0xFF800000 - 0xFFBFFFFF):
+To Flash U-boot into the alternative bank (0xEF800000 - 0xEFBFFFFF):
tftp 1000000 u-boot.bin
- erase ffb00000 +$filesize
- cp.b 1000000 ffb00000 $filesize
+ erase efb00000 +$filesize
+ cp.b 1000000 efb00000 $filesize
4. Memory Map
-------------
+NOTE: RIO and PCI are mutually exclusive, so they share an address
+
+For 32-bit u-boot, devices are mapped so that the virtual address ==
+the physical address, and the map looks liks this:
Memory Range Device Size
------------ ------ ----
0x0000_0000 0x7fff_ffff DDR 2G
+ 0x8000_0000 0x9fff_ffff RIO MEM 512M
0x8000_0000 0x9fff_ffff PCI1/PEX1 MEM 512M
- 0xa000_0000 0xafff_ffff PCI2/PEX2 MEM 512M
- 0xf800_0000 0xf80f_ffff CCSR 1M
- 0xf810_0000 0xf81f_ffff PIXIS 1M
+ 0xa000_0000 0xbfff_ffff PCI2/PEX2 MEM 512M
+ 0xffe0_0000 0xffef_ffff CCSR 1M
+ 0xffdf_0000 0xffdf_7fff PIXIS 8K
+ 0xffdf_8000 0xffdf_ffff CF 8K
0xf840_0000 0xf840_3fff Stack space 32K
- 0xe200_0000 0xe2ff_ffff PCI1/PEX1 IO 16M
- 0xe300_0000 0xe3ff_ffff PCI2/PEX2 IO 16M
- 0xfe00_0000 0xfeff_ffff Flash(alternate)16M
- 0xff00_0000 0xffff_ffff Flash(boot bank)16M
+ 0xffc0_0000 0xffc0_ffff PCI1/PEX1 IO 64K
+ 0xffc1_0000 0xffc1_ffff PCI2/PEX2 IO 64K
+ 0xef80_0000 0xefff_ffff Flash 8M
+
+For 36-bit-enabled u-boot, the virtual map is the same as for 32-bit.
+However, the physical map is altered to reside in 36-bit space, as follows.
+Addresses are no longer mapped with VA == PA. All accesses from
+software use the VA; the PA is only used for setting up windows
+and mappings. Note that with the exception of PCI MEM and RIO, the low
+ 32 bits are the same as the VA above; only the top 4 bits vary:
+
+ Memory Range Device Size
+ ------------ ------ ----
+ 0x0_0000_0000 0x0_7fff_ffff DDR 2G
+ 0xc_0000_0000 0xc_1fff_ffff RIO MEM 512M
+ 0xc_0000_0000 0xc_1fff_ffff PCI1/PEX1 MEM 512M
+ 0xc_2000_0000 0xc_3fff_ffff PCI2/PEX2 MEM 512M
+ 0xf_ffe0_0000 0xf_ffef_ffff CCSR 1M
+ 0xf_ffdf_0000 0xf_ffdf_7fff PIXIS 8K
+ 0xf_ffdf_8000 0xf_ffdf_ffff CF 8K
+ 0x0_f840_0000 0xf_f840_3fff Stack space 32K
+ 0xf_ffc0_0000 0xf_ffc0_ffff PCI1/PEX1 IO 64K
+ 0xf_ffc1_0000 0xf_ffc1_ffff PCI2/PEX2 IO 64K
+ 0xf_ef80_0000 0xf_efff_ffff Flash 8M
5. pixis_reset command
--------------------