summaryrefslogtreecommitdiff
path: root/doc
diff options
context:
space:
mode:
Diffstat (limited to 'doc')
-rw-r--r--doc/README.p1023rds101
1 files changed, 101 insertions, 0 deletions
diff --git a/doc/README.p1023rds b/doc/README.p1023rds
new file mode 100644
index 0000000..685f5da
--- /dev/null
+++ b/doc/README.p1023rds
@@ -0,0 +1,101 @@
+Overview
+--------
+The P1023 process includes a performance optimized implementation of the
+QorIQ data Path Acceleration Architecture (DPAA). This architecture
+provides the infrastructure to support simplified sharing of networking
+interfaces and accelerators by multiple CPU cores. P1023 is an e500 based
+dual core SOC.
+
+P1023RDS board is a Low End Dual core platform supporting the P1023
+processor of QorIQ series.
+
+Building U-boot
+---------------
+To build the u-boot for P1023RDS:
+Configure to NOR boot:
+ make P1023RDS_config
+Configure to NAND boot:
+ make P1023RDS_NAND_config
+Build:
+ make
+
+Board Switches
+--------------
+Most switches on the board should not be changed. The most frequent
+user-settable switches on the board are used to configure
+the flash banks.
+
+J4: all open
+
+Default NOR flash boot switch setting:
+ Sw3[1:8]: off on on off on on off off
+ Sw4[1:8]: off off off on off off off off
+ Sw6[1:8]: off on off on off on on off
+ Sw7[1:8]: off on off off on off off off
+ Sw8[1:8]: on off off off off off off off
+
+For NAND flash boot,set
+Sw4[1:4]: off on on on
+
+The default native ethernet setting is for RGMII mode.
+To use SGMII mode, set
+SW8[1:2]: OFF OFF
+SW7[6:7]: ON ON
+
+Memory Map
+----------
+0x0000_0000 0x7fff_ffff DDR 2G Cacheable
+0x8000_0000 0xbfff_ffff PCI Express Mem 1G non-cacheable
+0xc000_0000 0xdfff_ffff PCI 512M non-cacheable
+0xe100_0000 0xe3ff_ffff PCI IO range 4M non-cacheable
+
+0xe000_0000 0xe003_ffff BCSR 256K BCSR
+0xee00_0000 0xefff_ffff NOR flash 32M NOR flash
+0xff00_0000 0xff3f_ffff DPAA_QBMAN 4M
+0xff60_0000 0xff7f_ffff CCSR 2M non-cacheable
+0xffa0_0000 0xffaf_ffff NAND FLASH 1M non-cacheable
+0xffd0_0000 0xffd0_3fff L1 for stack 16K Cacheable TLB0
+
+Flashing u-boot Images
+---------------
+To program the image in the boot flash bank:
+NOR flash boot:
+ => tftp 1000000 u-boot.bin
+ => protect off all
+ => erase eff80000 efffffff
+ => cp.b 1000000 eff80000 80000
+
+NAND flash boot:
+ => tftp 1000000 u-boot-nand.bin
+ => nand erase 0 80000
+ => nand write 1000000 0 80000
+
+Firmware ucode location
+---------------------------------
+Microcode(ucode) to FMAN's IRAM is needed to make FMAN Ethernet work.
+u-boot loads ucode FLASH. The location for ucode:
+NOR Flash: 0xfe000000
+NAND Flash: 0x1f00000
+
+Using the Device Tree Source File
+---------------------------------
+To create the DTB (Device Tree Binary) image file,
+use a command similar to this:
+
+ dtc -b 0 -f -I dts -O dtb p1023rds.dts > p1023rds.dtb
+
+Likely, that .dts file will come from here;
+
+ linux-2.6/arch/powerpc/boot/dts/p1023rds.dts
+or
+ make p1023rds.dtb ARCH=powerpc
+in linux-2.6 directory.
+
+Booting Linux
+-------------
+Place a linux uImage in the TFTP disk area.
+
+ tftp 1000000 uImage
+ tftp 2000000 rootfs.ext2.gz.uboot
+ tftp c00000 p1023rds.dtb
+ bootm 1000000 2000000 c00000