summaryrefslogtreecommitdiff
path: root/drivers/net/e1000.c
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/net/e1000.c')
-rw-r--r--drivers/net/e1000.c3098
1 files changed, 2631 insertions, 467 deletions
diff --git a/drivers/net/e1000.c b/drivers/net/e1000.c
index a52749d..e3c6cea 100644
--- a/drivers/net/e1000.c
+++ b/drivers/net/e1000.c
@@ -51,7 +51,7 @@ tested on both gig copper and gig fiber boards
#define bus_to_phys(devno, a) pci_mem_to_phys(devno, a)
#define mdelay(n) udelay((n)*1000)
-#define E1000_DEFAULT_PBA 0x00000030
+#define E1000_DEFAULT_PBA 0x000a0026
/* NIC specific static variables go here */
@@ -82,6 +82,28 @@ static struct pci_device_id supported[] = {
{PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82540EM_LOM},
{PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82541ER},
{PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82541GI_LF},
+ /* E1000 PCIe card */
+ {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82571EB_COPPER},
+ {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82571EB_FIBER },
+ {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82571EB_SERDES },
+ {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82571EB_QUAD_COPPER},
+ {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82571PT_QUAD_COPPER},
+ {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82571EB_QUAD_FIBER},
+ {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82571EB_QUAD_COPPER_LOWPROFILE},
+ {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82571EB_SERDES_DUAL},
+ {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82571EB_SERDES_QUAD},
+ {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82572EI_COPPER},
+ {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82572EI_FIBER},
+ {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82572EI_SERDES},
+ {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82572EI},
+ {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82573E},
+ {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82573E_IAMT},
+ {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82573L},
+ {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82546GB_QUAD_COPPER_KSP3},
+ {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_80003ES2LAN_COPPER_DPT},
+ {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_80003ES2LAN_SERDES_DPT},
+ {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_80003ES2LAN_COPPER_SPT},
+ {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_80003ES2LAN_SERDES_SPT},
{}
};
@@ -95,16 +117,23 @@ static int e1000_config_mac_to_phy(struct e1000_hw *hw);
static int e1000_config_fc_after_link_up(struct e1000_hw *hw);
static int e1000_check_for_link(struct eth_device *nic);
static int e1000_wait_autoneg(struct e1000_hw *hw);
-static void e1000_get_speed_and_duplex(struct e1000_hw *hw, uint16_t * speed,
+static int e1000_get_speed_and_duplex(struct e1000_hw *hw, uint16_t * speed,
uint16_t * duplex);
static int e1000_read_phy_reg(struct e1000_hw *hw, uint32_t reg_addr,
uint16_t * phy_data);
static int e1000_write_phy_reg(struct e1000_hw *hw, uint32_t reg_addr,
uint16_t phy_data);
-static void e1000_phy_hw_reset(struct e1000_hw *hw);
+static int32_t e1000_phy_hw_reset(struct e1000_hw *hw);
static int e1000_phy_reset(struct e1000_hw *hw);
static int e1000_detect_gig_phy(struct e1000_hw *hw);
-
+static int32_t e1000_read_eeprom(struct e1000_hw *hw, uint16_t offset,
+ uint16_t words,
+ uint16_t *data);
+static void e1000_put_hw_eeprom_semaphore(struct e1000_hw *hw);
+static void e1000_set_media_type(struct e1000_hw *hw);
+
+static int32_t e1000_swfw_sync_acquire(struct e1000_hw *hw, uint16_t mask);
+static int32_t e1000_check_phy_reset_block(struct e1000_hw *hw);
#define E1000_WRITE_REG(a, reg, value) (writel((value), ((a)->hw_addr + E1000_##reg)))
#define E1000_READ_REG(a, reg) (readl((a)->hw_addr + E1000_##reg))
#define E1000_WRITE_REG_ARRAY(a, reg, offset, value) (\
@@ -204,17 +233,17 @@ e1000_shift_out_ee_bits(struct e1000_hw *hw, uint16_t data, uint16_t count)
* hw - Struct containing variables accessed by shared code
*****************************************************************************/
static uint16_t
-e1000_shift_in_ee_bits(struct e1000_hw *hw)
+e1000_shift_in_ee_bits(struct e1000_hw *hw, uint16_t count)
{
uint32_t eecd;
uint32_t i;
uint16_t data;
- /* In order to read a register from the EEPROM, we need to shift 16 bits
- * in from the EEPROM. Bits are "shifted in" by raising the clock input to
- * the EEPROM (setting the SK bit), and then reading the value of the "DO"
- * bit. During this "shifting in" process the "DI" bit should always be
- * clear..
+ /* In order to read a register from the EEPROM, we need to shift 'count'
+ * bits in from the EEPROM. Bits are "shifted in" by raising the clock
+ * input to the EEPROM (setting the SK bit), and then reading the
+ * value of the "DO" bit. During this "shifting in" process the
+ * "DI" bit should always be clear.
*/
eecd = E1000_READ_REG(hw, EECD);
@@ -222,7 +251,7 @@ e1000_shift_in_ee_bits(struct e1000_hw *hw)
eecd &= ~(E1000_EECD_DO | E1000_EECD_DI);
data = 0;
- for (i = 0; i < 16; i++) {
+ for (i = 0; i < count; i++) {
data = data << 1;
e1000_raise_ee_clk(hw, &eecd);
@@ -239,213 +268,600 @@ e1000_shift_in_ee_bits(struct e1000_hw *hw)
}
/******************************************************************************
- * Prepares EEPROM for access
+ * Returns EEPROM to a "standby" state
*
* hw - Struct containing variables accessed by shared code
- *
- * Lowers EEPROM clock. Clears input pin. Sets the chip select pin. This
- * function should be called before issuing a command to the EEPROM.
*****************************************************************************/
static void
-e1000_setup_eeprom(struct e1000_hw *hw)
+e1000_standby_eeprom(struct e1000_hw *hw)
{
+ struct e1000_eeprom_info *eeprom = &hw->eeprom;
uint32_t eecd;
eecd = E1000_READ_REG(hw, EECD);
- /* Clear SK and DI */
- eecd &= ~(E1000_EECD_SK | E1000_EECD_DI);
- E1000_WRITE_REG(hw, EECD, eecd);
+ if (eeprom->type == e1000_eeprom_microwire) {
+ eecd &= ~(E1000_EECD_CS | E1000_EECD_SK);
+ E1000_WRITE_REG(hw, EECD, eecd);
+ E1000_WRITE_FLUSH(hw);
+ udelay(eeprom->delay_usec);
- /* Set CS */
- eecd |= E1000_EECD_CS;
- E1000_WRITE_REG(hw, EECD, eecd);
+ /* Clock high */
+ eecd |= E1000_EECD_SK;
+ E1000_WRITE_REG(hw, EECD, eecd);
+ E1000_WRITE_FLUSH(hw);
+ udelay(eeprom->delay_usec);
+
+ /* Select EEPROM */
+ eecd |= E1000_EECD_CS;
+ E1000_WRITE_REG(hw, EECD, eecd);
+ E1000_WRITE_FLUSH(hw);
+ udelay(eeprom->delay_usec);
+
+ /* Clock low */
+ eecd &= ~E1000_EECD_SK;
+ E1000_WRITE_REG(hw, EECD, eecd);
+ E1000_WRITE_FLUSH(hw);
+ udelay(eeprom->delay_usec);
+ } else if (eeprom->type == e1000_eeprom_spi) {
+ /* Toggle CS to flush commands */
+ eecd |= E1000_EECD_CS;
+ E1000_WRITE_REG(hw, EECD, eecd);
+ E1000_WRITE_FLUSH(hw);
+ udelay(eeprom->delay_usec);
+ eecd &= ~E1000_EECD_CS;
+ E1000_WRITE_REG(hw, EECD, eecd);
+ E1000_WRITE_FLUSH(hw);
+ udelay(eeprom->delay_usec);
+ }
+}
+
+/***************************************************************************
+* Description: Determines if the onboard NVM is FLASH or EEPROM.
+*
+* hw - Struct containing variables accessed by shared code
+****************************************************************************/
+static boolean_t e1000_is_onboard_nvm_eeprom(struct e1000_hw *hw)
+{
+ uint32_t eecd = 0;
+
+ DEBUGFUNC();
+
+ if (hw->mac_type == e1000_ich8lan)
+ return FALSE;
+
+ if (hw->mac_type == e1000_82573) {
+ eecd = E1000_READ_REG(hw, EECD);
+
+ /* Isolate bits 15 & 16 */
+ eecd = ((eecd >> 15) & 0x03);
+
+ /* If both bits are set, device is Flash type */
+ if (eecd == 0x03)
+ return FALSE;
+ }
+ return TRUE;
}
/******************************************************************************
- * Returns EEPROM to a "standby" state
+ * Prepares EEPROM for access
*
* hw - Struct containing variables accessed by shared code
+ *
+ * Lowers EEPROM clock. Clears input pin. Sets the chip select pin. This
+ * function should be called before issuing a command to the EEPROM.
*****************************************************************************/
-static void
-e1000_standby_eeprom(struct e1000_hw *hw)
+static int32_t
+e1000_acquire_eeprom(struct e1000_hw *hw)
{
- uint32_t eecd;
+ struct e1000_eeprom_info *eeprom = &hw->eeprom;
+ uint32_t eecd, i = 0;
+ DEBUGOUT();
+
+ if (e1000_swfw_sync_acquire(hw, E1000_SWFW_EEP_SM))
+ return -E1000_ERR_SWFW_SYNC;
eecd = E1000_READ_REG(hw, EECD);
- /* Deselct EEPROM */
- eecd &= ~(E1000_EECD_CS | E1000_EECD_SK);
- E1000_WRITE_REG(hw, EECD, eecd);
- E1000_WRITE_FLUSH(hw);
- udelay(50);
+ if (hw->mac_type != e1000_82573) {
+ /* Request EEPROM Access */
+ if (hw->mac_type > e1000_82544) {
+ eecd |= E1000_EECD_REQ;
+ E1000_WRITE_REG(hw, EECD, eecd);
+ eecd = E1000_READ_REG(hw, EECD);
+ while ((!(eecd & E1000_EECD_GNT)) &&
+ (i < E1000_EEPROM_GRANT_ATTEMPTS)) {
+ i++;
+ udelay(5);
+ eecd = E1000_READ_REG(hw, EECD);
+ }
+ if (!(eecd & E1000_EECD_GNT)) {
+ eecd &= ~E1000_EECD_REQ;
+ E1000_WRITE_REG(hw, EECD, eecd);
+ DEBUGOUT("Could not acquire EEPROM grant\n");
+ return -E1000_ERR_EEPROM;
+ }
+ }
+ }
- /* Clock high */
- eecd |= E1000_EECD_SK;
- E1000_WRITE_REG(hw, EECD, eecd);
- E1000_WRITE_FLUSH(hw);
- udelay(50);
+ /* Setup EEPROM for Read/Write */
- /* Select EEPROM */
- eecd |= E1000_EECD_CS;
- E1000_WRITE_REG(hw, EECD, eecd);
- E1000_WRITE_FLUSH(hw);
- udelay(50);
+ if (eeprom->type == e1000_eeprom_microwire) {
+ /* Clear SK and DI */
+ eecd &= ~(E1000_EECD_DI | E1000_EECD_SK);
+ E1000_WRITE_REG(hw, EECD, eecd);
- /* Clock low */
- eecd &= ~E1000_EECD_SK;
- E1000_WRITE_REG(hw, EECD, eecd);
- E1000_WRITE_FLUSH(hw);
- udelay(50);
+ /* Set CS */
+ eecd |= E1000_EECD_CS;
+ E1000_WRITE_REG(hw, EECD, eecd);
+ } else if (eeprom->type == e1000_eeprom_spi) {
+ /* Clear SK and CS */
+ eecd &= ~(E1000_EECD_CS | E1000_EECD_SK);
+ E1000_WRITE_REG(hw, EECD, eecd);
+ udelay(1);
+ }
+
+ return E1000_SUCCESS;
}
/******************************************************************************
- * Reads a 16 bit word from the EEPROM.
+ * Sets up eeprom variables in the hw struct. Must be called after mac_type
+ * is configured. Additionally, if this is ICH8, the flash controller GbE
+ * registers must be mapped, or this will crash.
*
* hw - Struct containing variables accessed by shared code
- * offset - offset of word in the EEPROM to read
- * data - word read from the EEPROM
*****************************************************************************/
-static int
-e1000_read_eeprom(struct e1000_hw *hw, uint16_t offset, uint16_t * data)
+static int32_t e1000_init_eeprom_params(struct e1000_hw *hw)
{
- uint32_t eecd;
- uint32_t i = 0;
- int large_eeprom = FALSE;
+ struct e1000_eeprom_info *eeprom = &hw->eeprom;
+ uint32_t eecd = E1000_READ_REG(hw, EECD);
+ int32_t ret_val = E1000_SUCCESS;
+ uint16_t eeprom_size;
- /* Request EEPROM Access */
- if (hw->mac_type > e1000_82544) {
- eecd = E1000_READ_REG(hw, EECD);
- if (eecd & E1000_EECD_SIZE)
- large_eeprom = TRUE;
- eecd |= E1000_EECD_REQ;
- E1000_WRITE_REG(hw, EECD, eecd);
- eecd = E1000_READ_REG(hw, EECD);
- while ((!(eecd & E1000_EECD_GNT)) && (i < 100)) {
- i++;
- udelay(10);
- eecd = E1000_READ_REG(hw, EECD);
+ DEBUGOUT();
+
+ switch (hw->mac_type) {
+ case e1000_82542_rev2_0:
+ case e1000_82542_rev2_1:
+ case e1000_82543:
+ case e1000_82544:
+ eeprom->type = e1000_eeprom_microwire;
+ eeprom->word_size = 64;
+ eeprom->opcode_bits = 3;
+ eeprom->address_bits = 6;
+ eeprom->delay_usec = 50;
+ eeprom->use_eerd = FALSE;
+ eeprom->use_eewr = FALSE;
+ break;
+ case e1000_82540:
+ case e1000_82545:
+ case e1000_82545_rev_3:
+ case e1000_82546:
+ case e1000_82546_rev_3:
+ eeprom->type = e1000_eeprom_microwire;
+ eeprom->opcode_bits = 3;
+ eeprom->delay_usec = 50;
+ if (eecd & E1000_EECD_SIZE) {
+ eeprom->word_size = 256;
+ eeprom->address_bits = 8;
+ } else {
+ eeprom->word_size = 64;
+ eeprom->address_bits = 6;
+ }
+ eeprom->use_eerd = FALSE;
+ eeprom->use_eewr = FALSE;
+ break;
+ case e1000_82541:
+ case e1000_82541_rev_2:
+ case e1000_82547:
+ case e1000_82547_rev_2:
+ if (eecd & E1000_EECD_TYPE) {
+ eeprom->type = e1000_eeprom_spi;
+ eeprom->opcode_bits = 8;
+ eeprom->delay_usec = 1;
+ if (eecd & E1000_EECD_ADDR_BITS) {
+ eeprom->page_size = 32;
+ eeprom->address_bits = 16;
+ } else {
+ eeprom->page_size = 8;
+ eeprom->address_bits = 8;
+ }
+ } else {
+ eeprom->type = e1000_eeprom_microwire;
+ eeprom->opcode_bits = 3;
+ eeprom->delay_usec = 50;
+ if (eecd & E1000_EECD_ADDR_BITS) {
+ eeprom->word_size = 256;
+ eeprom->address_bits = 8;
+ } else {
+ eeprom->word_size = 64;
+ eeprom->address_bits = 6;
+ }
}
- if (!(eecd & E1000_EECD_GNT)) {
- eecd &= ~E1000_EECD_REQ;
+ eeprom->use_eerd = FALSE;
+ eeprom->use_eewr = FALSE;
+ break;
+ case e1000_82571:
+ case e1000_82572:
+ eeprom->type = e1000_eeprom_spi;
+ eeprom->opcode_bits = 8;
+ eeprom->delay_usec = 1;
+ if (eecd & E1000_EECD_ADDR_BITS) {
+ eeprom->page_size = 32;
+ eeprom->address_bits = 16;
+ } else {
+ eeprom->page_size = 8;
+ eeprom->address_bits = 8;
+ }
+ eeprom->use_eerd = FALSE;
+ eeprom->use_eewr = FALSE;
+ break;
+ case e1000_82573:
+ eeprom->type = e1000_eeprom_spi;
+ eeprom->opcode_bits = 8;
+ eeprom->delay_usec = 1;
+ if (eecd & E1000_EECD_ADDR_BITS) {
+ eeprom->page_size = 32;
+ eeprom->address_bits = 16;
+ } else {
+ eeprom->page_size = 8;
+ eeprom->address_bits = 8;
+ }
+ eeprom->use_eerd = TRUE;
+ eeprom->use_eewr = TRUE;
+ if (e1000_is_onboard_nvm_eeprom(hw) == FALSE) {
+ eeprom->type = e1000_eeprom_flash;
+ eeprom->word_size = 2048;
+
+ /* Ensure that the Autonomous FLASH update bit is cleared due to
+ * Flash update issue on parts which use a FLASH for NVM. */
+ eecd &= ~E1000_EECD_AUPDEN;
E1000_WRITE_REG(hw, EECD, eecd);
- DEBUGOUT("Could not acquire EEPROM grant\n");
- return -E1000_ERR_EEPROM;
}
- }
+ break;
+ case e1000_80003es2lan:
+ eeprom->type = e1000_eeprom_spi;
+ eeprom->opcode_bits = 8;
+ eeprom->delay_usec = 1;
+ if (eecd & E1000_EECD_ADDR_BITS) {
+ eeprom->page_size = 32;
+ eeprom->address_bits = 16;
+ } else {
+ eeprom->page_size = 8;
+ eeprom->address_bits = 8;
+ }
+ eeprom->use_eerd = TRUE;
+ eeprom->use_eewr = FALSE;
+ break;
- /* Prepare the EEPROM for reading */
- e1000_setup_eeprom(hw);
+ /* ich8lan does not support currently. if needed, please
+ * add corresponding code and functions.
+ */
+#if 0
+ case e1000_ich8lan:
+ {
+ int32_t i = 0;
+
+ eeprom->type = e1000_eeprom_ich8;
+ eeprom->use_eerd = FALSE;
+ eeprom->use_eewr = FALSE;
+ eeprom->word_size = E1000_SHADOW_RAM_WORDS;
+ uint32_t flash_size = E1000_READ_ICH_FLASH_REG(hw,
+ ICH_FLASH_GFPREG);
+ /* Zero the shadow RAM structure. But don't load it from NVM
+ * so as to save time for driver init */
+ if (hw->eeprom_shadow_ram != NULL) {
+ for (i = 0; i < E1000_SHADOW_RAM_WORDS; i++) {
+ hw->eeprom_shadow_ram[i].modified = FALSE;
+ hw->eeprom_shadow_ram[i].eeprom_word = 0xFFFF;
+ }
+ }
- /* Send the READ command (opcode + addr) */
- e1000_shift_out_ee_bits(hw, EEPROM_READ_OPCODE, 3);
- e1000_shift_out_ee_bits(hw, offset, (large_eeprom) ? 8 : 6);
+ hw->flash_base_addr = (flash_size & ICH_GFPREG_BASE_MASK) *
+ ICH_FLASH_SECTOR_SIZE;
- /* Read the data */
- *data = e1000_shift_in_ee_bits(hw);
+ hw->flash_bank_size = ((flash_size >> 16)
+ & ICH_GFPREG_BASE_MASK) + 1;
+ hw->flash_bank_size -= (flash_size & ICH_GFPREG_BASE_MASK);
- /* End this read operation */
- e1000_standby_eeprom(hw);
+ hw->flash_bank_size *= ICH_FLASH_SECTOR_SIZE;
- /* Stop requesting EEPROM access */
- if (hw->mac_type > e1000_82544) {
- eecd = E1000_READ_REG(hw, EECD);
- eecd &= ~E1000_EECD_REQ;
- E1000_WRITE_REG(hw, EECD, eecd);
+ hw->flash_bank_size /= 2 * sizeof(uint16_t);
+ break;
+ }
+#endif
+ default:
+ break;
}
- return 0;
+ if (eeprom->type == e1000_eeprom_spi) {
+ /* eeprom_size will be an enum [0..8] that maps
+ * to eeprom sizes 128B to
+ * 32KB (incremented by powers of 2).
+ */
+ if (hw->mac_type <= e1000_82547_rev_2) {
+ /* Set to default value for initial eeprom read. */
+ eeprom->word_size = 64;
+ ret_val = e1000_read_eeprom(hw, EEPROM_CFG, 1,
+ &eeprom_size);
+ if (ret_val)
+ return ret_val;
+ eeprom_size = (eeprom_size & EEPROM_SIZE_MASK)
+ >> EEPROM_SIZE_SHIFT;
+ /* 256B eeprom size was not supported in earlier
+ * hardware, so we bump eeprom_size up one to
+ * ensure that "1" (which maps to 256B) is never
+ * the result used in the shifting logic below. */
+ if (eeprom_size)
+ eeprom_size++;
+ } else {
+ eeprom_size = (uint16_t)((eecd &
+ E1000_EECD_SIZE_EX_MASK) >>
+ E1000_EECD_SIZE_EX_SHIFT);
+ }
+
+ eeprom->word_size = 1 << (eeprom_size + EEPROM_WORD_SIZE_SHIFT);
+ }
+ return ret_val;
}
-#if 0
-static void
-e1000_eeprom_cleanup(struct e1000_hw *hw)
+/******************************************************************************
+ * Polls the status bit (bit 1) of the EERD to determine when the read is done.
+ *
+ * hw - Struct containing variables accessed by shared code
+ *****************************************************************************/
+static int32_t
+e1000_poll_eerd_eewr_done(struct e1000_hw *hw, int eerd)
{
- uint32_t eecd;
+ uint32_t attempts = 100000;
+ uint32_t i, reg = 0;
+ int32_t done = E1000_ERR_EEPROM;
- eecd = E1000_READ_REG(hw, EECD);
- eecd &= ~(E1000_EECD_CS | E1000_EECD_DI);
- E1000_WRITE_REG(hw, EECD, eecd);
- e1000_raise_ee_clk(hw, &eecd);
- e1000_lower_ee_clk(hw, &eecd);
+ for (i = 0; i < attempts; i++) {
+ if (eerd == E1000_EEPROM_POLL_READ)
+ reg = E1000_READ_REG(hw, EERD);
+ else
+ reg = E1000_READ_REG(hw, EEWR);
+
+ if (reg & E1000_EEPROM_RW_REG_DONE) {
+ done = E1000_SUCCESS;
+ break;
+ }
+ udelay(5);
+ }
+
+ return done;
}
-static uint16_t
-e1000_wait_eeprom_done(struct e1000_hw *hw)
+/******************************************************************************
+ * Reads a 16 bit word from the EEPROM using the EERD register.
+ *
+ * hw - Struct containing variables accessed by shared code
+ * offset - offset of word in the EEPROM to read
+ * data - word read from the EEPROM
+ * words - number of words to read
+ *****************************************************************************/
+static int32_t
+e1000_read_eeprom_eerd(struct e1000_hw *hw,
+ uint16_t offset,
+ uint16_t words,
+ uint16_t *data)
{
- uint32_t eecd;
- uint32_t i;
+ uint32_t i, eerd = 0;
+ int32_t error = 0;
+
+ for (i = 0; i < words; i++) {
+ eerd = ((offset+i) << E1000_EEPROM_RW_ADDR_SHIFT) +
+ E1000_EEPROM_RW_REG_START;
+
+ E1000_WRITE_REG(hw, EERD, eerd);
+ error = e1000_poll_eerd_eewr_done(hw, E1000_EEPROM_POLL_READ);
+
+ if (error)
+ break;
+ data[i] = (E1000_READ_REG(hw, EERD) >>
+ E1000_EEPROM_RW_REG_DATA);
- e1000_standby_eeprom(hw);
- for (i = 0; i < 200; i++) {
- eecd = E1000_READ_REG(hw, EECD);
- if (eecd & E1000_EECD_DO)
- return (TRUE);
- udelay(5);
}
- return (FALSE);
+
+ return error;
}
-static int
-e1000_write_eeprom(struct e1000_hw *hw, uint16_t Reg, uint16_t Data)
+static void
+e1000_release_eeprom(struct e1000_hw *hw)
{
uint32_t eecd;
- int large_eeprom = FALSE;
- int i = 0;
- /* Request EEPROM Access */
- if (hw->mac_type > e1000_82544) {
- eecd = E1000_READ_REG(hw, EECD);
- if (eecd & E1000_EECD_SIZE)
- large_eeprom = TRUE;
- eecd |= E1000_EECD_REQ;
+ DEBUGFUNC();
+
+ eecd = E1000_READ_REG(hw, EECD);
+
+ if (hw->eeprom.type == e1000_eeprom_spi) {
+ eecd |= E1000_EECD_CS; /* Pull CS high */
+ eecd &= ~E1000_EECD_SK; /* Lower SCK */
+
E1000_WRITE_REG(hw, EECD, eecd);
- eecd = E1000_READ_REG(hw, EECD);
- while ((!(eecd & E1000_EECD_GNT)) && (i < 100)) {
- i++;
- udelay(5);
- eecd = E1000_READ_REG(hw, EECD);
- }
- if (!(eecd & E1000_EECD_GNT)) {
- eecd &= ~E1000_EECD_REQ;
- E1000_WRITE_REG(hw, EECD, eecd);
- DEBUGOUT("Could not acquire EEPROM grant\n");
- return FALSE;
- }
- }
- e1000_setup_eeprom(hw);
- e1000_shift_out_ee_bits(hw, EEPROM_EWEN_OPCODE, 5);
- e1000_shift_out_ee_bits(hw, Reg, (large_eeprom) ? 6 : 4);
- e1000_standby_eeprom(hw);
- e1000_shift_out_ee_bits(hw, EEPROM_WRITE_OPCODE, 3);
- e1000_shift_out_ee_bits(hw, Reg, (large_eeprom) ? 8 : 6);
- e1000_shift_out_ee_bits(hw, Data, 16);
- if (!e1000_wait_eeprom_done(hw)) {
- return FALSE;
+
+ udelay(hw->eeprom.delay_usec);
+ } else if (hw->eeprom.type == e1000_eeprom_microwire) {
+ /* cleanup eeprom */
+
+ /* CS on Microwire is active-high */
+ eecd &= ~(E1000_EECD_CS | E1000_EECD_DI);
+
+ E1000_WRITE_REG(hw, EECD, eecd);
+
+ /* Rising edge of clock */
+ eecd |= E1000_EECD_SK;
+ E1000_WRITE_REG(hw, EECD, eecd);
+ E1000_WRITE_FLUSH(hw);
+ udelay(hw->eeprom.delay_usec);
+
+ /* Falling edge of clock */
+ eecd &= ~E1000_EECD_SK;
+ E1000_WRITE_REG(hw, EECD, eecd);
+ E1000_WRITE_FLUSH(hw);
+ udelay(hw->eeprom.delay_usec);
}
- e1000_shift_out_ee_bits(hw, EEPROM_EWDS_OPCODE, 5);
- e1000_shift_out_ee_bits(hw, Reg, (large_eeprom) ? 6 : 4);
- e1000_eeprom_cleanup(hw);
/* Stop requesting EEPROM access */
if (hw->mac_type > e1000_82544) {
- eecd = E1000_READ_REG(hw, EECD);
eecd &= ~E1000_EECD_REQ;
E1000_WRITE_REG(hw, EECD, eecd);
}
- i = 0;
- eecd = E1000_READ_REG(hw, EECD);
- while (((eecd & E1000_EECD_GNT)) && (i < 500)) {
- i++;
- udelay(10);
- eecd = E1000_READ_REG(hw, EECD);
- }
- if ((eecd & E1000_EECD_GNT)) {
- DEBUGOUT("Could not release EEPROM grant\n");
+}
+/******************************************************************************
+ * Reads a 16 bit word from the EEPROM.
+ *
+ * hw - Struct containing variables accessed by shared code
+ *****************************************************************************/
+static int32_t
+e1000_spi_eeprom_ready(struct e1000_hw *hw)
+{
+ uint16_t retry_count = 0;
+ uint8_t spi_stat_reg;
+
+ DEBUGFUNC();
+
+ /* Read "Status Register" repeatedly until the LSB is cleared. The
+ * EEPROM will signal that the command has been completed by clearing
+ * bit 0 of the internal status register. If it's not cleared within
+ * 5 milliseconds, then error out.
+ */
+ retry_count = 0;
+ do {
+ e1000_shift_out_ee_bits(hw, EEPROM_RDSR_OPCODE_SPI,
+ hw->eeprom.opcode_bits);
+ spi_stat_reg = (uint8_t)e1000_shift_in_ee_bits(hw, 8);
+ if (!(spi_stat_reg & EEPROM_STATUS_RDY_SPI))
+ break;
+
+ udelay(5);
+ retry_count += 5;
+
+ e1000_standby_eeprom(hw);
+ } while (retry_count < EEPROM_MAX_RETRY_SPI);
+
+ /* ATMEL SPI write time could vary from 0-20mSec on 3.3V devices (and
+ * only 0-5mSec on 5V devices)
+ */
+ if (retry_count >= EEPROM_MAX_RETRY_SPI) {
+ DEBUGOUT("SPI EEPROM Status error\n");
+ return -E1000_ERR_EEPROM;
}
- return TRUE;
+
+ return E1000_SUCCESS;
}
+
+/******************************************************************************
+ * Reads a 16 bit word from the EEPROM.
+ *
+ * hw - Struct containing variables accessed by shared code
+ * offset - offset of word in the EEPROM to read
+ * data - word read from the EEPROM
+ *****************************************************************************/
+static int32_t
+e1000_read_eeprom(struct e1000_hw *hw, uint16_t offset,
+ uint16_t words, uint16_t *data)
+{
+ struct e1000_eeprom_info *eeprom = &hw->eeprom;
+ uint32_t i = 0;
+
+ DEBUGFUNC();
+
+ /* If eeprom is not yet detected, do so now */
+ if (eeprom->word_size == 0)
+ e1000_init_eeprom_params(hw);
+
+ /* A check for invalid values: offset too large, too many words,
+ * and not enough words.
+ */
+ if ((offset >= eeprom->word_size) ||
+ (words > eeprom->word_size - offset) ||
+ (words == 0)) {
+ DEBUGOUT("\"words\" parameter out of bounds."
+ "Words = %d, size = %d\n", offset, eeprom->word_size);
+ return -E1000_ERR_EEPROM;
+ }
+
+ /* EEPROM's that don't use EERD to read require us to bit-bang the SPI
+ * directly. In this case, we need to acquire the EEPROM so that
+ * FW or other port software does not interrupt.
+ */
+ if (e1000_is_onboard_nvm_eeprom(hw) == TRUE &&
+ hw->eeprom.use_eerd == FALSE) {
+
+ /* Prepare the EEPROM for bit-bang reading */
+ if (e1000_acquire_eeprom(hw) != E1000_SUCCESS)
+ return -E1000_ERR_EEPROM;
+ }
+
+ /* Eerd register EEPROM access requires no eeprom aquire/release */
+ if (eeprom->use_eerd == TRUE)
+ return e1000_read_eeprom_eerd(hw, offset, words, data);
+
+ /* ich8lan does not support currently. if needed, please
+ * add corresponding code and functions.
+ */
+#if 0
+ /* ICH EEPROM access is done via the ICH flash controller */
+ if (eeprom->type == e1000_eeprom_ich8)
+ return e1000_read_eeprom_ich8(hw, offset, words, data);
#endif
+ /* Set up the SPI or Microwire EEPROM for bit-bang reading. We have
+ * acquired the EEPROM at this point, so any returns should relase it */
+ if (eeprom->type == e1000_eeprom_spi) {
+ uint16_t word_in;
+ uint8_t read_opcode = EEPROM_READ_OPCODE_SPI;
+
+ if (e1000_spi_eeprom_ready(hw)) {
+ e1000_release_eeprom(hw);
+ return -E1000_ERR_EEPROM;
+ }
+
+ e1000_standby_eeprom(hw);
+
+ /* Some SPI eeproms use the 8th address bit embedded in
+ * the opcode */
+ if ((eeprom->address_bits == 8) && (offset >= 128))
+ read_opcode |= EEPROM_A8_OPCODE_SPI;
+
+ /* Send the READ command (opcode + addr) */
+ e1000_shift_out_ee_bits(hw, read_opcode, eeprom->opcode_bits);
+ e1000_shift_out_ee_bits(hw, (uint16_t)(offset*2),
+ eeprom->address_bits);
+
+ /* Read the data. The address of the eeprom internally
+ * increments with each byte (spi) being read, saving on the
+ * overhead of eeprom setup and tear-down. The address
+ * counter will roll over if reading beyond the size of
+ * the eeprom, thus allowing the entire memory to be read
+ * starting from any offset. */
+ for (i = 0; i < words; i++) {
+ word_in = e1000_shift_in_ee_bits(hw, 16);
+ data[i] = (word_in >> 8) | (word_in << 8);
+ }
+ } else if (eeprom->type == e1000_eeprom_microwire) {
+ for (i = 0; i < words; i++) {
+ /* Send the READ command (opcode + addr) */
+ e1000_shift_out_ee_bits(hw,
+ EEPROM_READ_OPCODE_MICROWIRE,
+ eeprom->opcode_bits);
+ e1000_shift_out_ee_bits(hw, (uint16_t)(offset + i),
+ eeprom->address_bits);
+
+ /* Read the data. For microwire, each word requires
+ * the overhead of eeprom setup and tear-down. */
+ data[i] = e1000_shift_in_ee_bits(hw, 16);
+ e1000_standby_eeprom(hw);
+ }
+ }
+
+ /* End this read operation */
+ e1000_release_eeprom(hw);
+
+ return E1000_SUCCESS;
+}
/******************************************************************************
* Verifies that the EEPROM has a valid checksum
@@ -466,7 +882,7 @@ e1000_validate_eeprom_checksum(struct eth_device *nic)
DEBUGFUNC();
for (i = 0; i < (EEPROM_CHECKSUM_REG + 1); i++) {
- if (e1000_read_eeprom(hw, i, &eeprom_data) < 0) {
+ if (e1000_read_eeprom(hw, i, 1, &eeprom_data) < 0) {
DEBUGOUT("EEPROM Read Error\n");
return -E1000_ERR_EEPROM;
}
@@ -482,6 +898,162 @@ e1000_validate_eeprom_checksum(struct eth_device *nic)
}
#endif /* #ifndef CONFIG_AP1000 */
+/***************************************************************************
+ *
+ * Obtaining software semaphore bit (SMBI) before resetting PHY.
+ *
+ * hw: Struct containing variables accessed by shared code
+ *
+ * returns: - E1000_ERR_RESET if fail to obtain semaphore.
+ * E1000_SUCCESS at any other case.
+ *
+ ***************************************************************************/
+static int32_t
+e1000_get_software_semaphore(struct e1000_hw *hw)
+{
+ int32_t timeout = hw->eeprom.word_size + 1;
+ uint32_t swsm;
+
+ DEBUGFUNC();
+
+ if (hw->mac_type != e1000_80003es2lan)
+ return E1000_SUCCESS;
+
+ while (timeout) {
+ swsm = E1000_READ_REG(hw, SWSM);
+ /* If SMBI bit cleared, it is now set and we hold
+ * the semaphore */
+ if (!(swsm & E1000_SWSM_SMBI))
+ break;
+ mdelay(1);
+ timeout--;
+ }
+
+ if (!timeout) {
+ DEBUGOUT("Driver can't access device - SMBI bit is set.\n");
+ return -E1000_ERR_RESET;
+ }
+
+ return E1000_SUCCESS;
+}
+
+/***************************************************************************
+ * This function clears HW semaphore bits.
+ *
+ * hw: Struct containing variables accessed by shared code
+ *
+ * returns: - None.
+ *
+ ***************************************************************************/
+static void
+e1000_put_hw_eeprom_semaphore(struct e1000_hw *hw)
+{
+ uint32_t swsm;
+
+ DEBUGFUNC();
+
+ if (!hw->eeprom_semaphore_present)
+ return;
+
+ swsm = E1000_READ_REG(hw, SWSM);
+ if (hw->mac_type == e1000_80003es2lan) {
+ /* Release both semaphores. */
+ swsm &= ~(E1000_SWSM_SMBI | E1000_SWSM_SWESMBI);
+ } else
+ swsm &= ~(E1000_SWSM_SWESMBI);
+ E1000_WRITE_REG(hw, SWSM, swsm);
+}
+
+/***************************************************************************
+ *
+ * Using the combination of SMBI and SWESMBI semaphore bits when resetting
+ * adapter or Eeprom access.
+ *
+ * hw: Struct containing variables accessed by shared code
+ *
+ * returns: - E1000_ERR_EEPROM if fail to access EEPROM.
+ * E1000_SUCCESS at any other case.
+ *
+ ***************************************************************************/
+static int32_t
+e1000_get_hw_eeprom_semaphore(struct e1000_hw *hw)
+{
+ int32_t timeout;
+ uint32_t swsm;
+
+ DEBUGFUNC();
+
+ if (!hw->eeprom_semaphore_present)
+ return E1000_SUCCESS;
+
+ if (hw->mac_type == e1000_80003es2lan) {
+ /* Get the SW semaphore. */
+ if (e1000_get_software_semaphore(hw) != E1000_SUCCESS)
+ return -E1000_ERR_EEPROM;
+ }
+
+ /* Get the FW semaphore. */
+ timeout = hw->eeprom.word_size + 1;
+ while (timeout) {
+ swsm = E1000_READ_REG(hw, SWSM);
+ swsm |= E1000_SWSM_SWESMBI;
+ E1000_WRITE_REG(hw, SWSM, swsm);
+ /* if we managed to set the bit we got the semaphore. */
+ swsm = E1000_READ_REG(hw, SWSM);
+ if (swsm & E1000_SWSM_SWESMBI)
+ break;
+
+ udelay(50);
+ timeout--;
+ }
+
+ if (!timeout) {
+ /* Release semaphores */
+ e1000_put_hw_eeprom_semaphore(hw);
+ DEBUGOUT("Driver can't access the Eeprom - "
+ "SWESMBI bit is set.\n");
+ return -E1000_ERR_EEPROM;
+ }
+
+ return E1000_SUCCESS;
+}
+
+static int32_t
+e1000_swfw_sync_acquire(struct e1000_hw *hw, uint16_t mask)
+{
+ uint32_t swfw_sync = 0;
+ uint32_t swmask = mask;
+ uint32_t fwmask = mask << 16;
+ int32_t timeout = 200;
+
+ DEBUGFUNC();
+ while (timeout) {
+ if (e1000_get_hw_eeprom_semaphore(hw))
+ return -E1000_ERR_SWFW_SYNC;
+
+ swfw_sync = E1000_READ_REG(hw, SW_FW_SYNC);
+ if (!(swfw_sync & (fwmask | swmask)))
+ break;
+
+ /* firmware currently using resource (fwmask) */
+ /* or other software thread currently using resource (swmask) */
+ e1000_put_hw_eeprom_semaphore(hw);
+ mdelay(5);
+ timeout--;
+ }
+
+ if (!timeout) {
+ DEBUGOUT("Driver can't access resource, SW_FW_SYNC timeout.\n");
+ return -E1000_ERR_SWFW_SYNC;
+ }
+
+ swfw_sync |= swmask;
+ E1000_WRITE_REG(hw, SW_FW_SYNC, swfw_sync);
+
+ e1000_put_hw_eeprom_semaphore(hw);
+ return E1000_SUCCESS;
+}
+
/******************************************************************************
* Reads the adapter's MAC address from the EEPROM and inverts the LSB for the
* second function of dual function devices
@@ -501,7 +1073,7 @@ e1000_read_mac_addr(struct eth_device *nic)
for (i = 0; i < NODE_ADDRESS_SIZE; i += 2) {
offset = i >> 1;
- if (e1000_read_eeprom(hw, offset, &eeprom_data) < 0) {
+ if (e1000_read_eeprom(hw, offset, 1, &eeprom_data) < 0) {
DEBUGOUT("EEPROM Read Error\n");
return -E1000_ERR_EEPROM;
}
@@ -605,7 +1177,7 @@ e1000_clear_vfta(struct e1000_hw *hw)
*
* hw - Struct containing variables accessed by shared code
*****************************************************************************/
-static int
+int32_t
e1000_set_mac_type(struct e1000_hw *hw)
{
DEBUGFUNC();
@@ -636,21 +1208,88 @@ e1000_set_mac_type(struct e1000_hw *hw)
break;
case E1000_DEV_ID_82540EM:
case E1000_DEV_ID_82540EM_LOM:
+ case E1000_DEV_ID_82540EP:
+ case E1000_DEV_ID_82540EP_LOM:
+ case E1000_DEV_ID_82540EP_LP:
hw->mac_type = e1000_82540;
break;
case E1000_DEV_ID_82545EM_COPPER:
- case E1000_DEV_ID_82545GM_COPPER:
case E1000_DEV_ID_82545EM_FIBER:
hw->mac_type = e1000_82545;
break;
+ case E1000_DEV_ID_82545GM_COPPER:
+ case E1000_DEV_ID_82545GM_FIBER:
+ case E1000_DEV_ID_82545GM_SERDES:
+ hw->mac_type = e1000_82545_rev_3;
+ break;
case E1000_DEV_ID_82546EB_COPPER:
case E1000_DEV_ID_82546EB_FIBER:
+ case E1000_DEV_ID_82546EB_QUAD_COPPER:
hw->mac_type = e1000_82546;
break;
+ case E1000_DEV_ID_82546GB_COPPER:
+ case E1000_DEV_ID_82546GB_FIBER:
+ case E1000_DEV_ID_82546GB_SERDES:
+ case E1000_DEV_ID_82546GB_PCIE:
+ case E1000_DEV_ID_82546GB_QUAD_COPPER:
+ case E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3:
+ hw->mac_type = e1000_82546_rev_3;
+ break;
+ case E1000_DEV_ID_82541EI:
+ case E1000_DEV_ID_82541EI_MOBILE:
+ case E1000_DEV_ID_82541ER_LOM:
+ hw->mac_type = e1000_82541;
+ break;
case E1000_DEV_ID_82541ER:
+ case E1000_DEV_ID_82541GI:
case E1000_DEV_ID_82541GI_LF:
+ case E1000_DEV_ID_82541GI_MOBILE:
hw->mac_type = e1000_82541_rev_2;
break;
+ case E1000_DEV_ID_82547EI:
+ case E1000_DEV_ID_82547EI_MOBILE:
+ hw->mac_type = e1000_82547;
+ break;
+ case E1000_DEV_ID_82547GI:
+ hw->mac_type = e1000_82547_rev_2;
+ break;
+ case E1000_DEV_ID_82571EB_COPPER:
+ case E1000_DEV_ID_82571EB_FIBER:
+ case E1000_DEV_ID_82571EB_SERDES:
+ case E1000_DEV_ID_82571EB_SERDES_DUAL:
+ case E1000_DEV_ID_82571EB_SERDES_QUAD:
+ case E1000_DEV_ID_82571EB_QUAD_COPPER:
+ case E1000_DEV_ID_82571PT_QUAD_COPPER:
+ case E1000_DEV_ID_82571EB_QUAD_FIBER:
+ case E1000_DEV_ID_82571EB_QUAD_COPPER_LOWPROFILE:
+ hw->mac_type = e1000_82571;
+ break;
+ case E1000_DEV_ID_82572EI_COPPER:
+ case E1000_DEV_ID_82572EI_FIBER:
+ case E1000_DEV_ID_82572EI_SERDES:
+ case E1000_DEV_ID_82572EI:
+ hw->mac_type = e1000_82572;
+ break;
+ case E1000_DEV_ID_82573E:
+ case E1000_DEV_ID_82573E_IAMT:
+ case E1000_DEV_ID_82573L:
+ hw->mac_type = e1000_82573;
+ break;
+ case E1000_DEV_ID_80003ES2LAN_COPPER_SPT:
+ case E1000_DEV_ID_80003ES2LAN_SERDES_SPT:
+ case E1000_DEV_ID_80003ES2LAN_COPPER_DPT:
+ case E1000_DEV_ID_80003ES2LAN_SERDES_DPT:
+ hw->mac_type = e1000_80003es2lan;
+ break;
+ case E1000_DEV_ID_ICH8_IGP_M_AMT:
+ case E1000_DEV_ID_ICH8_IGP_AMT:
+ case E1000_DEV_ID_ICH8_IGP_C:
+ case E1000_DEV_ID_ICH8_IFE:
+ case E1000_DEV_ID_ICH8_IFE_GT:
+ case E1000_DEV_ID_ICH8_IFE_G:
+ case E1000_DEV_ID_ICH8_IGP_M:
+ hw->mac_type = e1000_ich8lan;
+ break;
default:
/* Should never have loaded on this device */
return -E1000_ERR_MAC_TYPE;
@@ -677,8 +1316,7 @@ e1000_reset_hw(struct e1000_hw *hw)
if (hw->mac_type == e1000_82542_rev2_0) {
DEBUGOUT("Disabling MWI on 82542 rev 2.0\n");
pci_write_config_word(hw->pdev, PCI_COMMAND,
- hw->
- pci_cmd_word & ~PCI_COMMAND_INVALIDATE);
+ hw->pci_cmd_word & ~PCI_COMMAND_INVALIDATE);
}
/* Clear interrupt mask to stop board from generating interrupts */
@@ -709,12 +1347,7 @@ e1000_reset_hw(struct e1000_hw *hw)
DEBUGOUT("Issuing a global reset to MAC\n");
ctrl = E1000_READ_REG(hw, CTRL);
-#if 0
- if (hw->mac_type > e1000_82543)
- E1000_WRITE_REG_IO(hw, CTRL, (ctrl | E1000_CTRL_RST));
- else
-#endif
- E1000_WRITE_REG(hw, CTRL, (ctrl | E1000_CTRL_RST));
+ E1000_WRITE_REG(hw, CTRL, (ctrl | E1000_CTRL_RST));
/* Force a reload from the EEPROM if necessary */
if (hw->mac_type < e1000_82540) {
@@ -746,6 +1379,127 @@ e1000_reset_hw(struct e1000_hw *hw)
if (hw->mac_type == e1000_82542_rev2_0) {
pci_write_config_word(hw->pdev, PCI_COMMAND, hw->pci_cmd_word);
}
+ E1000_WRITE_REG(hw, PBA, E1000_DEFAULT_PBA);
+}
+
+/******************************************************************************
+ *
+ * Initialize a number of hardware-dependent bits
+ *
+ * hw: Struct containing variables accessed by shared code
+ *
+ * This function contains hardware limitation workarounds for PCI-E adapters
+ *
+ *****************************************************************************/
+static void
+e1000_initialize_hardware_bits(struct e1000_hw *hw)
+{
+ if ((hw->mac_type >= e1000_82571) &&
+ (!hw->initialize_hw_bits_disable)) {
+ /* Settings common to all PCI-express silicon */
+ uint32_t reg_ctrl, reg_ctrl_ext;
+ uint32_t reg_tarc0, reg_tarc1;
+ uint32_t reg_tctl;
+ uint32_t reg_txdctl, reg_txdctl1;
+
+ /* link autonegotiation/sync workarounds */
+ reg_tarc0 = E1000_READ_REG(hw, TARC0);
+ reg_tarc0 &= ~((1 << 30)|(1 << 29)|(1 << 28)|(1 << 27));
+
+ /* Enable not-done TX descriptor counting */
+ reg_txdctl = E1000_READ_REG(hw, TXDCTL);
+ reg_txdctl |= E1000_TXDCTL_COUNT_DESC;
+ E1000_WRITE_REG(hw, TXDCTL, reg_txdctl);
+
+ reg_txdctl1 = E1000_READ_REG(hw, TXDCTL1);
+ reg_txdctl1 |= E1000_TXDCTL_COUNT_DESC;
+ E1000_WRITE_REG(hw, TXDCTL1, reg_txdctl1);
+
+ switch (hw->mac_type) {
+ case e1000_82571:
+ case e1000_82572:
+ /* Clear PHY TX compatible mode bits */
+ reg_tarc1 = E1000_READ_REG(hw, TARC1);
+ reg_tarc1 &= ~((1 << 30)|(1 << 29));
+
+ /* link autonegotiation/sync workarounds */
+ reg_tarc0 |= ((1 << 26)|(1 << 25)|(1 << 24)|(1 << 23));
+
+ /* TX ring control fixes */
+ reg_tarc1 |= ((1 << 26)|(1 << 25)|(1 << 24));
+
+ /* Multiple read bit is reversed polarity */
+ reg_tctl = E1000_READ_REG(hw, TCTL);
+ if (reg_tctl & E1000_TCTL_MULR)
+ reg_tarc1 &= ~(1 << 28);
+ else
+ reg_tarc1 |= (1 << 28);
+
+ E1000_WRITE_REG(hw, TARC1, reg_tarc1);
+ break;
+ case e1000_82573:
+ reg_ctrl_ext = E1000_READ_REG(hw, CTRL_EXT);
+ reg_ctrl_ext &= ~(1 << 23);
+ reg_ctrl_ext |= (1 << 22);
+
+ /* TX byte count fix */
+ reg_ctrl = E1000_READ_REG(hw, CTRL);
+ reg_ctrl &= ~(1 << 29);
+
+ E1000_WRITE_REG(hw, CTRL_EXT, reg_ctrl_ext);
+ E1000_WRITE_REG(hw, CTRL, reg_ctrl);
+ break;
+ case e1000_80003es2lan:
+ /* improve small packet performace for fiber/serdes */
+ if ((hw->media_type == e1000_media_type_fiber)
+ || (hw->media_type ==
+ e1000_media_type_internal_serdes)) {
+ reg_tarc0 &= ~(1 << 20);
+ }
+
+ /* Multiple read bit is reversed polarity */
+ reg_tctl = E1000_READ_REG(hw, TCTL);
+ reg_tarc1 = E1000_READ_REG(hw, TARC1);
+ if (reg_tctl & E1000_TCTL_MULR)
+ reg_tarc1 &= ~(1 << 28);
+ else
+ reg_tarc1 |= (1 << 28);
+
+ E1000_WRITE_REG(hw, TARC1, reg_tarc1);
+ break;
+ case e1000_ich8lan:
+ /* Reduce concurrent DMA requests to 3 from 4 */
+ if ((hw->revision_id < 3) ||
+ ((hw->device_id != E1000_DEV_ID_ICH8_IGP_M_AMT) &&
+ (hw->device_id != E1000_DEV_ID_ICH8_IGP_M)))
+ reg_tarc0 |= ((1 << 29)|(1 << 28));
+
+ reg_ctrl_ext = E1000_READ_REG(hw, CTRL_EXT);
+ reg_ctrl_ext |= (1 << 22);
+ E1000_WRITE_REG(hw, CTRL_EXT, reg_ctrl_ext);
+
+ /* workaround TX hang with TSO=on */
+ reg_tarc0 |= ((1 << 27)|(1 << 26)|(1 << 24)|(1 << 23));
+
+ /* Multiple read bit is reversed polarity */
+ reg_tctl = E1000_READ_REG(hw, TCTL);
+ reg_tarc1 = E1000_READ_REG(hw, TARC1);
+ if (reg_tctl & E1000_TCTL_MULR)
+ reg_tarc1 &= ~(1 << 28);
+ else
+ reg_tarc1 |= (1 << 28);
+
+ /* workaround TX hang with TSO=on */
+ reg_tarc1 |= ((1 << 30)|(1 << 26)|(1 << 24));
+
+ E1000_WRITE_REG(hw, TARC1, reg_tarc1);
+ break;
+ default:
+ break;
+ }
+
+ E1000_WRITE_REG(hw, TARC0, reg_tarc0);
+ }
}
/******************************************************************************
@@ -763,49 +1517,43 @@ static int
e1000_init_hw(struct eth_device *nic)
{
struct e1000_hw *hw = nic->priv;
- uint32_t ctrl, status;
+ uint32_t ctrl;
uint32_t i;
int32_t ret_val;
uint16_t pcix_cmd_word;
uint16_t pcix_stat_hi_word;
uint16_t cmd_mmrbc;
uint16_t stat_mmrbc;
- e1000_bus_type bus_type = e1000_bus_type_unknown;
-
+ uint32_t mta_size;
+ uint32_t reg_data;
+ uint32_t ctrl_ext;
DEBUGFUNC();
-#if 0
- /* Initialize Identification LED */
- ret_val = e1000_id_led_init(hw);
- if (ret_val < 0) {
- DEBUGOUT("Error Initializing Identification LED\n");
- return ret_val;
- }
-#endif
- /* Set the Media Type and exit with error if it is not valid. */
- if (hw->mac_type != e1000_82543) {
- /* tbi_compatibility is only valid on 82543 */
- hw->tbi_compatibility_en = FALSE;
+ /* force full DMA clock frequency for 10/100 on ICH8 A0-B0 */
+ if ((hw->mac_type == e1000_ich8lan) &&
+ ((hw->revision_id < 3) ||
+ ((hw->device_id != E1000_DEV_ID_ICH8_IGP_M_AMT) &&
+ (hw->device_id != E1000_DEV_ID_ICH8_IGP_M)))) {
+ reg_data = E1000_READ_REG(hw, STATUS);
+ reg_data &= ~0x80000000;
+ E1000_WRITE_REG(hw, STATUS, reg_data);
}
+ /* Do not need initialize Identification LED */
- if (hw->mac_type >= e1000_82543) {
- status = E1000_READ_REG(hw, STATUS);
- if (status & E1000_STATUS_TBIMODE) {
- hw->media_type = e1000_media_type_fiber;
- /* tbi_compatibility not valid on fiber */
- hw->tbi_compatibility_en = FALSE;
- } else {
- hw->media_type = e1000_media_type_copper;
- }
- } else {
- /* This is an 82542 (fiber only) */
- hw->media_type = e1000_media_type_fiber;
- }
+ /* Set the media type and TBI compatibility */
+ e1000_set_media_type(hw);
+
+ /* Must be called after e1000_set_media_type
+ * because media_type is used */
+ e1000_initialize_hardware_bits(hw);
/* Disabling VLAN filtering. */
DEBUGOUT("Initializing the IEEE VLAN\n");
- E1000_WRITE_REG(hw, VET, 0);
-
- e1000_clear_vfta(hw);
+ /* VET hardcoded to standard value and VFTA removed in ICH8 LAN */
+ if (hw->mac_type != e1000_ich8lan) {
+ if (hw->mac_type < e1000_82545_rev_3)
+ E1000_WRITE_REG(hw, VET, 0);
+ e1000_clear_vfta(hw);
+ }
/* For 82542 (rev 2.0), disable MWI and put the receiver into reset */
if (hw->mac_type == e1000_82542_rev2_0) {
@@ -833,26 +1581,33 @@ e1000_init_hw(struct eth_device *nic)
/* Zero out the Multicast HASH table */
DEBUGOUT("Zeroing the MTA\n");
- for (i = 0; i < E1000_MC_TBL_SIZE; i++)
+ mta_size = E1000_MC_TBL_SIZE;
+ if (hw->mac_type == e1000_ich8lan)
+ mta_size = E1000_MC_TBL_SIZE_ICH8LAN;
+ for (i = 0; i < mta_size; i++) {
E1000_WRITE_REG_ARRAY(hw, MTA, i, 0);
-
+ /* use write flush to prevent Memory Write Block (MWB) from
+ * occuring when accessing our register space */
+ E1000_WRITE_FLUSH(hw);
+ }
#if 0
/* Set the PCI priority bit correctly in the CTRL register. This
* determines if the adapter gives priority to receives, or if it
- * gives equal priority to transmits and receives.
+ * gives equal priority to transmits and receives. Valid only on
+ * 82542 and 82543 silicon.
*/
- if (hw->dma_fairness) {
+ if (hw->dma_fairness && hw->mac_type <= e1000_82543) {
ctrl = E1000_READ_REG(hw, CTRL);
E1000_WRITE_REG(hw, CTRL, ctrl | E1000_CTRL_PRIOR);
}
#endif
- if (hw->mac_type >= e1000_82543) {
- status = E1000_READ_REG(hw, STATUS);
- bus_type = (status & E1000_STATUS_PCIX_MODE) ?
- e1000_bus_type_pcix : e1000_bus_type_pci;
- }
+ switch (hw->mac_type) {
+ case e1000_82545_rev_3:
+ case e1000_82546_rev_3:
+ break;
+ default:
/* Workaround for PCI-X problem when BIOS sets MMRBC incorrectly. */
- if (bus_type == e1000_bus_type_pcix) {
+ if (hw->bus_type == e1000_bus_type_pcix) {
pci_read_config_word(hw->pdev, PCIX_COMMAND_REGISTER,
&pcix_cmd_word);
pci_read_config_word(hw->pdev, PCIX_STATUS_REGISTER_HI,
@@ -872,6 +1627,12 @@ e1000_init_hw(struct eth_device *nic)
pcix_cmd_word);
}
}
+ break;
+ }
+
+ /* More time needed for PHY to initialize */
+ if (hw->mac_type == e1000_ich8lan)
+ mdelay(15);
/* Call a subroutine to configure the link and setup flow control. */
ret_val = e1000_setup_link(nic);
@@ -884,6 +1645,48 @@ e1000_init_hw(struct eth_device *nic)
E1000_TXDCTL_FULL_TX_DESC_WB;
E1000_WRITE_REG(hw, TXDCTL, ctrl);
}
+
+ switch (hw->mac_type) {
+ default:
+ break;
+ case e1000_80003es2lan:
+ /* Enable retransmit on late collisions */
+ reg_data = E1000_READ_REG(hw, TCTL);
+ reg_data |= E1000_TCTL_RTLC;
+ E1000_WRITE_REG(hw, TCTL, reg_data);
+
+ /* Configure Gigabit Carry Extend Padding */
+ reg_data = E1000_READ_REG(hw, TCTL_EXT);
+ reg_data &= ~E1000_TCTL_EXT_GCEX_MASK;
+ reg_data |= DEFAULT_80003ES2LAN_TCTL_EXT_GCEX;
+ E1000_WRITE_REG(hw, TCTL_EXT, reg_data);
+
+ /* Configure Transmit Inter-Packet Gap */
+ reg_data = E1000_READ_REG(hw, TIPG);
+ reg_data &= ~E1000_TIPG_IPGT_MASK;
+ reg_data |= DEFAULT_80003ES2LAN_TIPG_IPGT_1000;
+ E1000_WRITE_REG(hw, TIPG, reg_data);
+
+ reg_data = E1000_READ_REG_ARRAY(hw, FFLT, 0x0001);
+ reg_data &= ~0x00100000;
+ E1000_WRITE_REG_ARRAY(hw, FFLT, 0x0001, reg_data);
+ /* Fall through */
+ case e1000_82571:
+ case e1000_82572:
+ case e1000_ich8lan:
+ ctrl = E1000_READ_REG(hw, TXDCTL1);
+ ctrl = (ctrl & ~E1000_TXDCTL_WTHRESH)
+ | E1000_TXDCTL_FULL_TX_DESC_WB;
+ E1000_WRITE_REG(hw, TXDCTL1, ctrl);
+ break;
+ }
+
+ if (hw->mac_type == e1000_82573) {
+ uint32_t gcr = E1000_READ_REG(hw, GCR);
+ gcr |= E1000_GCR_L1_ACT_WITHOUT_L0S_RX;
+ E1000_WRITE_REG(hw, GCR, gcr);
+ }
+
#if 0
/* Clear all of the statistics registers (clear on read). It is
* important that we do this after we have tried to establish link
@@ -891,8 +1694,22 @@ e1000_init_hw(struct eth_device *nic)
* is no link.
*/
e1000_clear_hw_cntrs(hw);
+
+ /* ICH8 No-snoop bits are opposite polarity.
+ * Set to snoop by default after reset. */
+ if (hw->mac_type == e1000_ich8lan)
+ e1000_set_pci_ex_no_snoop(hw, PCI_EX_82566_SNOOP_ALL);
#endif
+ if (hw->device_id == E1000_DEV_ID_82546GB_QUAD_COPPER ||
+ hw->device_id == E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3) {
+ ctrl_ext = E1000_READ_REG(hw, CTRL_EXT);
+ /* Relaxed ordering must be disabled to avoid a parity
+ * error crash in a PCI slot. */
+ ctrl_ext |= E1000_CTRL_EXT_RO_DIS;
+ E1000_WRITE_REG(hw, CTRL_EXT, ctrl_ext);
+ }
+
return ret_val;
}
@@ -917,6 +1734,11 @@ e1000_setup_link(struct eth_device *nic)
DEBUGFUNC();
+ /* In the case of the phy reset being blocked, we already have a link.
+ * We do not have to set it up again. */
+ if (e1000_check_phy_reset_block(hw))
+ return E1000_SUCCESS;
+
#ifndef CONFIG_AP1000
/* Read and store word 0x0F of the EEPROM. This word contains bits
* that determine the hardware's default PAUSE (flow control) mode,
@@ -926,7 +1748,8 @@ e1000_setup_link(struct eth_device *nic)
* control setting, then the variable hw->fc will
* be initialized based on a value in the EEPROM.
*/
- if (e1000_read_eeprom(hw, EEPROM_INIT_CONTROL2_REG, &eeprom_data) < 0) {
+ if (e1000_read_eeprom(hw, EEPROM_INIT_CONTROL2_REG, 1,
+ &eeprom_data) < 0) {
DEBUGOUT("EEPROM Read Error\n");
return -E1000_ERR_EEPROM;
}
@@ -937,13 +1760,31 @@ e1000_setup_link(struct eth_device *nic)
#endif
if (hw->fc == e1000_fc_default) {
- if ((eeprom_data & EEPROM_WORD0F_PAUSE_MASK) == 0)
- hw->fc = e1000_fc_none;
- else if ((eeprom_data & EEPROM_WORD0F_PAUSE_MASK) ==
- EEPROM_WORD0F_ASM_DIR)
- hw->fc = e1000_fc_tx_pause;
- else
+ switch (hw->mac_type) {
+ case e1000_ich8lan:
+ case e1000_82573:
hw->fc = e1000_fc_full;
+ break;
+ default:
+#ifndef CONFIG_AP1000
+ ret_val = e1000_read_eeprom(hw,
+ EEPROM_INIT_CONTROL2_REG, 1, &eeprom_data);
+ if (ret_val) {
+ DEBUGOUT("EEPROM Read Error\n");
+ return -E1000_ERR_EEPROM;
+ }
+#else
+ eeprom_data = 0xb220;
+#endif
+ if ((eeprom_data & EEPROM_WORD0F_PAUSE_MASK) == 0)
+ hw->fc = e1000_fc_none;
+ else if ((eeprom_data & EEPROM_WORD0F_PAUSE_MASK) ==
+ EEPROM_WORD0F_ASM_DIR)
+ hw->fc = e1000_fc_tx_pause;
+ else
+ hw->fc = e1000_fc_full;
+ break;
+ }
}
/* We want to save off the original Flow Control configuration just
@@ -985,12 +1826,16 @@ e1000_setup_link(struct eth_device *nic)
* control is disabled, because it does not hurt anything to
* initialize these registers.
*/
- DEBUGOUT
- ("Initializing the Flow Control address, type and timer regs\n");
+ DEBUGOUT("Initializing the Flow Control address, type"
+ "and timer regs\n");
+
+ /* FCAL/H and FCT are hardcoded to standard values in e1000_ich8lan. */
+ if (hw->mac_type != e1000_ich8lan) {
+ E1000_WRITE_REG(hw, FCT, FLOW_CONTROL_TYPE);
+ E1000_WRITE_REG(hw, FCAH, FLOW_CONTROL_ADDRESS_HIGH);
+ E1000_WRITE_REG(hw, FCAL, FLOW_CONTROL_ADDRESS_LOW);
+ }
- E1000_WRITE_REG(hw, FCAL, FLOW_CONTROL_ADDRESS_LOW);
- E1000_WRITE_REG(hw, FCAH, FLOW_CONTROL_ADDRESS_HIGH);
- E1000_WRITE_REG(hw, FCT, FLOW_CONTROL_TYPE);
E1000_WRITE_REG(hw, FCTTV, hw->fc_pause_time);
/* Set the flow control receive threshold registers. Normally,
@@ -1154,18 +1999,57 @@ e1000_setup_fiber_link(struct eth_device *nic)
return 0;
}
+/*****************************************************************************
+ * Set PHY to class A mode
+ * Assumes the following operations will follow to enable the new class mode.
+ * 1. Do a PHY soft reset
+ * 2. Restart auto-negotiation or force link.
+ *
+ * hw - Struct containing variables accessed by shared code
+ ****************************************************************************/
+static int32_t
+e1000_set_phy_mode(struct e1000_hw *hw)
+{
+ int32_t ret_val;
+ uint16_t eeprom_data;
+
+ DEBUGFUNC();
+
+ if ((hw->mac_type == e1000_82545_rev_3) &&
+ (hw->media_type == e1000_media_type_copper)) {
+ ret_val = e1000_read_eeprom(hw, EEPROM_PHY_CLASS_WORD,
+ 1, &eeprom_data);
+ if (ret_val)
+ return ret_val;
+
+ if ((eeprom_data != EEPROM_RESERVED_WORD) &&
+ (eeprom_data & EEPROM_PHY_CLASS_A)) {
+ ret_val = e1000_write_phy_reg(hw,
+ M88E1000_PHY_PAGE_SELECT, 0x000B);
+ if (ret_val)
+ return ret_val;
+ ret_val = e1000_write_phy_reg(hw,
+ M88E1000_PHY_GEN_CONTROL, 0x8104);
+ if (ret_val)
+ return ret_val;
+
+ hw->phy_reset_disable = FALSE;
+ }
+ }
+
+ return E1000_SUCCESS;
+}
+
/******************************************************************************
-* Detects which PHY is present and the speed and duplex
+* Make sure we have a valid PHY and change PHY mode before link setup.
*
* hw - Struct containing variables accessed by shared code
******************************************************************************/
-static int
-e1000_setup_copper_link(struct eth_device *nic)
+static int32_t
+e1000_copper_link_preconfig(struct e1000_hw *hw)
{
- struct e1000_hw *hw = nic->priv;
uint32_t ctrl;
int32_t ret_val;
- uint16_t i;
uint16_t phy_data;
DEBUGFUNC();
@@ -1180,28 +2064,684 @@ e1000_setup_copper_link(struct eth_device *nic)
ctrl &= ~(E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX);
E1000_WRITE_REG(hw, CTRL, ctrl);
} else {
- ctrl |=
- (E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX | E1000_CTRL_SLU);
+ ctrl |= (E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX
+ | E1000_CTRL_SLU);
E1000_WRITE_REG(hw, CTRL, ctrl);
- e1000_phy_hw_reset(hw);
+ ret_val = e1000_phy_hw_reset(hw);
+ if (ret_val)
+ return ret_val;
}
/* Make sure we have a valid PHY */
ret_val = e1000_detect_gig_phy(hw);
- if (ret_val < 0) {
+ if (ret_val) {
DEBUGOUT("Error, did not detect valid phy.\n");
return ret_val;
}
DEBUGOUT("Phy ID = %x \n", hw->phy_id);
- /* Enable CRS on TX. This must be set for half-duplex operation. */
- if (e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data) < 0) {
- DEBUGOUT("PHY Read Error\n");
- return -E1000_ERR_PHY;
+#ifndef CONFIG_AP1000
+ /* Set PHY to class A mode (if necessary) */
+ ret_val = e1000_set_phy_mode(hw);
+ if (ret_val)
+ return ret_val;
+#endif
+ if ((hw->mac_type == e1000_82545_rev_3) ||
+ (hw->mac_type == e1000_82546_rev_3)) {
+ ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL,
+ &phy_data);
+ phy_data |= 0x00000008;
+ ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_SPEC_CTRL,
+ phy_data);
+ }
+
+ if (hw->mac_type <= e1000_82543 ||
+ hw->mac_type == e1000_82541 || hw->mac_type == e1000_82547 ||
+ hw->mac_type == e1000_82541_rev_2
+ || hw->mac_type == e1000_82547_rev_2)
+ hw->phy_reset_disable = FALSE;
+
+ return E1000_SUCCESS;
+}
+
+/*****************************************************************************
+ *
+ * This function sets the lplu state according to the active flag. When
+ * activating lplu this function also disables smart speed and vise versa.
+ * lplu will not be activated unless the device autonegotiation advertisment
+ * meets standards of either 10 or 10/100 or 10/100/1000 at all duplexes.
+ * hw: Struct containing variables accessed by shared code
+ * active - true to enable lplu false to disable lplu.
+ *
+ * returns: - E1000_ERR_PHY if fail to read/write the PHY
+ * E1000_SUCCESS at any other case.
+ *
+ ****************************************************************************/
+
+static int32_t
+e1000_set_d3_lplu_state(struct e1000_hw *hw, boolean_t active)
+{
+ uint32_t phy_ctrl = 0;
+ int32_t ret_val;
+ uint16_t phy_data;
+ DEBUGFUNC();
+
+ if (hw->phy_type != e1000_phy_igp && hw->phy_type != e1000_phy_igp_2
+ && hw->phy_type != e1000_phy_igp_3)
+ return E1000_SUCCESS;
+
+ /* During driver activity LPLU should not be used or it will attain link
+ * from the lowest speeds starting from 10Mbps. The capability is used
+ * for Dx transitions and states */
+ if (hw->mac_type == e1000_82541_rev_2
+ || hw->mac_type == e1000_82547_rev_2) {
+ ret_val = e1000_read_phy_reg(hw, IGP01E1000_GMII_FIFO,
+ &phy_data);
+ if (ret_val)
+ return ret_val;
+ } else if (hw->mac_type == e1000_ich8lan) {
+ /* MAC writes into PHY register based on the state transition
+ * and start auto-negotiation. SW driver can overwrite the
+ * settings in CSR PHY power control E1000_PHY_CTRL register. */
+ phy_ctrl = E1000_READ_REG(hw, PHY_CTRL);
+ } else {
+ ret_val = e1000_read_phy_reg(hw, IGP02E1000_PHY_POWER_MGMT,
+ &phy_data);
+ if (ret_val)
+ return ret_val;
+ }
+
+ if (!active) {
+ if (hw->mac_type == e1000_82541_rev_2 ||
+ hw->mac_type == e1000_82547_rev_2) {
+ phy_data &= ~IGP01E1000_GMII_FLEX_SPD;
+ ret_val = e1000_write_phy_reg(hw, IGP01E1000_GMII_FIFO,
+ phy_data);
+ if (ret_val)
+ return ret_val;
+ } else {
+ if (hw->mac_type == e1000_ich8lan) {
+ phy_ctrl &= ~E1000_PHY_CTRL_NOND0A_LPLU;
+ E1000_WRITE_REG(hw, PHY_CTRL, phy_ctrl);
+ } else {
+ phy_data &= ~IGP02E1000_PM_D3_LPLU;
+ ret_val = e1000_write_phy_reg(hw,
+ IGP02E1000_PHY_POWER_MGMT, phy_data);
+ if (ret_val)
+ return ret_val;
+ }
+ }
+
+ /* LPLU and SmartSpeed are mutually exclusive. LPLU is used during
+ * Dx states where the power conservation is most important. During
+ * driver activity we should enable SmartSpeed, so performance is
+ * maintained. */
+ if (hw->smart_speed == e1000_smart_speed_on) {
+ ret_val = e1000_read_phy_reg(hw,
+ IGP01E1000_PHY_PORT_CONFIG, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ phy_data |= IGP01E1000_PSCFR_SMART_SPEED;
+ ret_val = e1000_write_phy_reg(hw,
+ IGP01E1000_PHY_PORT_CONFIG, phy_data);
+ if (ret_val)
+ return ret_val;
+ } else if (hw->smart_speed == e1000_smart_speed_off) {
+ ret_val = e1000_read_phy_reg(hw,
+ IGP01E1000_PHY_PORT_CONFIG, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ phy_data &= ~IGP01E1000_PSCFR_SMART_SPEED;
+ ret_val = e1000_write_phy_reg(hw,
+ IGP01E1000_PHY_PORT_CONFIG, phy_data);
+ if (ret_val)
+ return ret_val;
+ }
+
+ } else if ((hw->autoneg_advertised == AUTONEG_ADVERTISE_SPEED_DEFAULT)
+ || (hw->autoneg_advertised == AUTONEG_ADVERTISE_10_ALL) ||
+ (hw->autoneg_advertised == AUTONEG_ADVERTISE_10_100_ALL)) {
+
+ if (hw->mac_type == e1000_82541_rev_2 ||
+ hw->mac_type == e1000_82547_rev_2) {
+ phy_data |= IGP01E1000_GMII_FLEX_SPD;
+ ret_val = e1000_write_phy_reg(hw,
+ IGP01E1000_GMII_FIFO, phy_data);
+ if (ret_val)
+ return ret_val;
+ } else {
+ if (hw->mac_type == e1000_ich8lan) {
+ phy_ctrl |= E1000_PHY_CTRL_NOND0A_LPLU;
+ E1000_WRITE_REG(hw, PHY_CTRL, phy_ctrl);
+ } else {
+ phy_data |= IGP02E1000_PM_D3_LPLU;
+ ret_val = e1000_write_phy_reg(hw,
+ IGP02E1000_PHY_POWER_MGMT, phy_data);
+ if (ret_val)
+ return ret_val;
+ }
+ }
+
+ /* When LPLU is enabled we should disable SmartSpeed */
+ ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG,
+ &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ phy_data &= ~IGP01E1000_PSCFR_SMART_SPEED;
+ ret_val = e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG,
+ phy_data);
+ if (ret_val)
+ return ret_val;
+ }
+ return E1000_SUCCESS;
+}
+
+/*****************************************************************************
+ *
+ * This function sets the lplu d0 state according to the active flag. When
+ * activating lplu this function also disables smart speed and vise versa.
+ * lplu will not be activated unless the device autonegotiation advertisment
+ * meets standards of either 10 or 10/100 or 10/100/1000 at all duplexes.
+ * hw: Struct containing variables accessed by shared code
+ * active - true to enable lplu false to disable lplu.
+ *
+ * returns: - E1000_ERR_PHY if fail to read/write the PHY
+ * E1000_SUCCESS at any other case.
+ *
+ ****************************************************************************/
+
+static int32_t
+e1000_set_d0_lplu_state(struct e1000_hw *hw, boolean_t active)
+{
+ uint32_t phy_ctrl = 0;
+ int32_t ret_val;
+ uint16_t phy_data;
+ DEBUGFUNC();
+
+ if (hw->mac_type <= e1000_82547_rev_2)
+ return E1000_SUCCESS;
+
+ if (hw->mac_type == e1000_ich8lan) {
+ phy_ctrl = E1000_READ_REG(hw, PHY_CTRL);
+ } else {
+ ret_val = e1000_read_phy_reg(hw, IGP02E1000_PHY_POWER_MGMT,
+ &phy_data);
+ if (ret_val)
+ return ret_val;
+ }
+
+ if (!active) {
+ if (hw->mac_type == e1000_ich8lan) {
+ phy_ctrl &= ~E1000_PHY_CTRL_D0A_LPLU;
+ E1000_WRITE_REG(hw, PHY_CTRL, phy_ctrl);
+ } else {
+ phy_data &= ~IGP02E1000_PM_D0_LPLU;
+ ret_val = e1000_write_phy_reg(hw,
+ IGP02E1000_PHY_POWER_MGMT, phy_data);
+ if (ret_val)
+ return ret_val;
+ }
+
+ /* LPLU and SmartSpeed are mutually exclusive. LPLU is used during
+ * Dx states where the power conservation is most important. During
+ * driver activity we should enable SmartSpeed, so performance is
+ * maintained. */
+ if (hw->smart_speed == e1000_smart_speed_on) {
+ ret_val = e1000_read_phy_reg(hw,
+ IGP01E1000_PHY_PORT_CONFIG, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ phy_data |= IGP01E1000_PSCFR_SMART_SPEED;
+ ret_val = e1000_write_phy_reg(hw,
+ IGP01E1000_PHY_PORT_CONFIG, phy_data);
+ if (ret_val)
+ return ret_val;
+ } else if (hw->smart_speed == e1000_smart_speed_off) {
+ ret_val = e1000_read_phy_reg(hw,
+ IGP01E1000_PHY_PORT_CONFIG, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ phy_data &= ~IGP01E1000_PSCFR_SMART_SPEED;
+ ret_val = e1000_write_phy_reg(hw,
+ IGP01E1000_PHY_PORT_CONFIG, phy_data);
+ if (ret_val)
+ return ret_val;
+ }
+
+
+ } else {
+
+ if (hw->mac_type == e1000_ich8lan) {
+ phy_ctrl |= E1000_PHY_CTRL_D0A_LPLU;
+ E1000_WRITE_REG(hw, PHY_CTRL, phy_ctrl);
+ } else {
+ phy_data |= IGP02E1000_PM_D0_LPLU;
+ ret_val = e1000_write_phy_reg(hw,
+ IGP02E1000_PHY_POWER_MGMT, phy_data);
+ if (ret_val)
+ return ret_val;
+ }
+
+ /* When LPLU is enabled we should disable SmartSpeed */
+ ret_val = e1000_read_phy_reg(hw,
+ IGP01E1000_PHY_PORT_CONFIG, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ phy_data &= ~IGP01E1000_PSCFR_SMART_SPEED;
+ ret_val = e1000_write_phy_reg(hw,
+ IGP01E1000_PHY_PORT_CONFIG, phy_data);
+ if (ret_val)
+ return ret_val;
+
+ }
+ return E1000_SUCCESS;
+}
+
+/********************************************************************
+* Copper link setup for e1000_phy_igp series.
+*
+* hw - Struct containing variables accessed by shared code
+*********************************************************************/
+static int32_t
+e1000_copper_link_igp_setup(struct e1000_hw *hw)
+{
+ uint32_t led_ctrl;
+ int32_t ret_val;
+ uint16_t phy_data;
+
+ DEBUGOUT();
+
+ if (hw->phy_reset_disable)
+ return E1000_SUCCESS;
+
+ ret_val = e1000_phy_reset(hw);
+ if (ret_val) {
+ DEBUGOUT("Error Resetting the PHY\n");
+ return ret_val;
+ }
+
+ /* Wait 15ms for MAC to configure PHY from eeprom settings */
+ mdelay(15);
+ if (hw->mac_type != e1000_ich8lan) {
+ /* Configure activity LED after PHY reset */
+ led_ctrl = E1000_READ_REG(hw, LEDCTL);
+ led_ctrl &= IGP_ACTIVITY_LED_MASK;
+ led_ctrl |= (IGP_ACTIVITY_LED_ENABLE | IGP_LED3_MODE);
+ E1000_WRITE_REG(hw, LEDCTL, led_ctrl);
+ }
+
+ /* The NVM settings will configure LPLU in D3 for IGP2 and IGP3 PHYs */
+ if (hw->phy_type == e1000_phy_igp) {
+ /* disable lplu d3 during driver init */
+ ret_val = e1000_set_d3_lplu_state(hw, FALSE);
+ if (ret_val) {
+ DEBUGOUT("Error Disabling LPLU D3\n");
+ return ret_val;
+ }
+ }
+
+ /* disable lplu d0 during driver init */
+ ret_val = e1000_set_d0_lplu_state(hw, FALSE);
+ if (ret_val) {
+ DEBUGOUT("Error Disabling LPLU D0\n");
+ return ret_val;
+ }
+ /* Configure mdi-mdix settings */
+ ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CTRL, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ if ((hw->mac_type == e1000_82541) || (hw->mac_type == e1000_82547)) {
+ hw->dsp_config_state = e1000_dsp_config_disabled;
+ /* Force MDI for earlier revs of the IGP PHY */
+ phy_data &= ~(IGP01E1000_PSCR_AUTO_MDIX
+ | IGP01E1000_PSCR_FORCE_MDI_MDIX);
+ hw->mdix = 1;
+
+ } else {
+ hw->dsp_config_state = e1000_dsp_config_enabled;
+ phy_data &= ~IGP01E1000_PSCR_AUTO_MDIX;
+
+ switch (hw->mdix) {
+ case 1:
+ phy_data &= ~IGP01E1000_PSCR_FORCE_MDI_MDIX;
+ break;
+ case 2:
+ phy_data |= IGP01E1000_PSCR_FORCE_MDI_MDIX;
+ break;
+ case 0:
+ default:
+ phy_data |= IGP01E1000_PSCR_AUTO_MDIX;
+ break;
+ }
+ }
+ ret_val = e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CTRL, phy_data);
+ if (ret_val)
+ return ret_val;
+
+ /* set auto-master slave resolution settings */
+ if (hw->autoneg) {
+ e1000_ms_type phy_ms_setting = hw->master_slave;
+
+ if (hw->ffe_config_state == e1000_ffe_config_active)
+ hw->ffe_config_state = e1000_ffe_config_enabled;
+
+ if (hw->dsp_config_state == e1000_dsp_config_activated)
+ hw->dsp_config_state = e1000_dsp_config_enabled;
+
+ /* when autonegotiation advertisment is only 1000Mbps then we
+ * should disable SmartSpeed and enable Auto MasterSlave
+ * resolution as hardware default. */
+ if (hw->autoneg_advertised == ADVERTISE_1000_FULL) {
+ /* Disable SmartSpeed */
+ ret_val = e1000_read_phy_reg(hw,
+ IGP01E1000_PHY_PORT_CONFIG, &phy_data);
+ if (ret_val)
+ return ret_val;
+ phy_data &= ~IGP01E1000_PSCFR_SMART_SPEED;
+ ret_val = e1000_write_phy_reg(hw,
+ IGP01E1000_PHY_PORT_CONFIG, phy_data);
+ if (ret_val)
+ return ret_val;
+ /* Set auto Master/Slave resolution process */
+ ret_val = e1000_read_phy_reg(hw, PHY_1000T_CTRL,
+ &phy_data);
+ if (ret_val)
+ return ret_val;
+ phy_data &= ~CR_1000T_MS_ENABLE;
+ ret_val = e1000_write_phy_reg(hw, PHY_1000T_CTRL,
+ phy_data);
+ if (ret_val)
+ return ret_val;
+ }
+
+ ret_val = e1000_read_phy_reg(hw, PHY_1000T_CTRL, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ /* load defaults for future use */
+ hw->original_master_slave = (phy_data & CR_1000T_MS_ENABLE) ?
+ ((phy_data & CR_1000T_MS_VALUE) ?
+ e1000_ms_force_master :
+ e1000_ms_force_slave) :
+ e1000_ms_auto;
+
+ switch (phy_ms_setting) {
+ case e1000_ms_force_master:
+ phy_data |= (CR_1000T_MS_ENABLE | CR_1000T_MS_VALUE);
+ break;
+ case e1000_ms_force_slave:
+ phy_data |= CR_1000T_MS_ENABLE;
+ phy_data &= ~(CR_1000T_MS_VALUE);
+ break;
+ case e1000_ms_auto:
+ phy_data &= ~CR_1000T_MS_ENABLE;
+ default:
+ break;
+ }
+ ret_val = e1000_write_phy_reg(hw, PHY_1000T_CTRL, phy_data);
+ if (ret_val)
+ return ret_val;
}
+
+ return E1000_SUCCESS;
+}
+
+/*****************************************************************************
+ * This function checks the mode of the firmware.
+ *
+ * returns - TRUE when the mode is IAMT or FALSE.
+ ****************************************************************************/
+boolean_t
+e1000_check_mng_mode(struct e1000_hw *hw)
+{
+ uint32_t fwsm;
+ DEBUGFUNC();
+
+ fwsm = E1000_READ_REG(hw, FWSM);
+
+ if (hw->mac_type == e1000_ich8lan) {
+ if ((fwsm & E1000_FWSM_MODE_MASK) ==
+ (E1000_MNG_ICH_IAMT_MODE << E1000_FWSM_MODE_SHIFT))
+ return TRUE;
+ } else if ((fwsm & E1000_FWSM_MODE_MASK) ==
+ (E1000_MNG_IAMT_MODE << E1000_FWSM_MODE_SHIFT))
+ return TRUE;
+
+ return FALSE;
+}
+
+static int32_t
+e1000_write_kmrn_reg(struct e1000_hw *hw, uint32_t reg_addr, uint16_t data)
+{
+ uint32_t reg_val;
+ uint16_t swfw;
+ DEBUGFUNC();
+
+ if ((hw->mac_type == e1000_80003es2lan) &&
+ (E1000_READ_REG(hw, STATUS) & E1000_STATUS_FUNC_1)) {
+ swfw = E1000_SWFW_PHY1_SM;
+ } else {
+ swfw = E1000_SWFW_PHY0_SM;
+ }
+ if (e1000_swfw_sync_acquire(hw, swfw))
+ return -E1000_ERR_SWFW_SYNC;
+
+ reg_val = ((reg_addr << E1000_KUMCTRLSTA_OFFSET_SHIFT)
+ & E1000_KUMCTRLSTA_OFFSET) | data;
+ E1000_WRITE_REG(hw, KUMCTRLSTA, reg_val);
+ udelay(2);
+
+ return E1000_SUCCESS;
+}
+
+static int32_t
+e1000_read_kmrn_reg(struct e1000_hw *hw, uint32_t reg_addr, uint16_t *data)
+{
+ uint32_t reg_val;
+ uint16_t swfw;
+ DEBUGFUNC();
+
+ if ((hw->mac_type == e1000_80003es2lan) &&
+ (E1000_READ_REG(hw, STATUS) & E1000_STATUS_FUNC_1)) {
+ swfw = E1000_SWFW_PHY1_SM;
+ } else {
+ swfw = E1000_SWFW_PHY0_SM;
+ }
+ if (e1000_swfw_sync_acquire(hw, swfw))
+ return -E1000_ERR_SWFW_SYNC;
+
+ /* Write register address */
+ reg_val = ((reg_addr << E1000_KUMCTRLSTA_OFFSET_SHIFT) &
+ E1000_KUMCTRLSTA_OFFSET) | E1000_KUMCTRLSTA_REN;
+ E1000_WRITE_REG(hw, KUMCTRLSTA, reg_val);
+ udelay(2);
+
+ /* Read the data returned */
+ reg_val = E1000_READ_REG(hw, KUMCTRLSTA);
+ *data = (uint16_t)reg_val;
+
+ return E1000_SUCCESS;
+}
+
+/********************************************************************
+* Copper link setup for e1000_phy_gg82563 series.
+*
+* hw - Struct containing variables accessed by shared code
+*********************************************************************/
+static int32_t
+e1000_copper_link_ggp_setup(struct e1000_hw *hw)
+{
+ int32_t ret_val;
+ uint16_t phy_data;
+ uint32_t reg_data;
+
+ DEBUGFUNC();
+
+ if (!hw->phy_reset_disable) {
+ /* Enable CRS on TX for half-duplex operation. */
+ ret_val = e1000_read_phy_reg(hw,
+ GG82563_PHY_MAC_SPEC_CTRL, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ phy_data |= GG82563_MSCR_ASSERT_CRS_ON_TX;
+ /* Use 25MHz for both link down and 1000BASE-T for Tx clock */
+ phy_data |= GG82563_MSCR_TX_CLK_1000MBPS_25MHZ;
+
+ ret_val = e1000_write_phy_reg(hw,
+ GG82563_PHY_MAC_SPEC_CTRL, phy_data);
+ if (ret_val)
+ return ret_val;
+
+ /* Options:
+ * MDI/MDI-X = 0 (default)
+ * 0 - Auto for all speeds
+ * 1 - MDI mode
+ * 2 - MDI-X mode
+ * 3 - Auto for 1000Base-T only (MDI-X for 10/100Base-T modes)
+ */
+ ret_val = e1000_read_phy_reg(hw,
+ GG82563_PHY_SPEC_CTRL, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ phy_data &= ~GG82563_PSCR_CROSSOVER_MODE_MASK;
+
+ switch (hw->mdix) {
+ case 1:
+ phy_data |= GG82563_PSCR_CROSSOVER_MODE_MDI;
+ break;
+ case 2:
+ phy_data |= GG82563_PSCR_CROSSOVER_MODE_MDIX;
+ break;
+ case 0:
+ default:
+ phy_data |= GG82563_PSCR_CROSSOVER_MODE_AUTO;
+ break;
+ }
+
+ /* Options:
+ * disable_polarity_correction = 0 (default)
+ * Automatic Correction for Reversed Cable Polarity
+ * 0 - Disabled
+ * 1 - Enabled
+ */
+ phy_data &= ~GG82563_PSCR_POLARITY_REVERSAL_DISABLE;
+ ret_val = e1000_write_phy_reg(hw,
+ GG82563_PHY_SPEC_CTRL, phy_data);
+
+ if (ret_val)
+ return ret_val;
+
+ /* SW Reset the PHY so all changes take effect */
+ ret_val = e1000_phy_reset(hw);
+ if (ret_val) {
+ DEBUGOUT("Error Resetting the PHY\n");
+ return ret_val;
+ }
+ } /* phy_reset_disable */
+
+ if (hw->mac_type == e1000_80003es2lan) {
+ /* Bypass RX and TX FIFO's */
+ ret_val = e1000_write_kmrn_reg(hw,
+ E1000_KUMCTRLSTA_OFFSET_FIFO_CTRL,
+ E1000_KUMCTRLSTA_FIFO_CTRL_RX_BYPASS
+ | E1000_KUMCTRLSTA_FIFO_CTRL_TX_BYPASS);
+ if (ret_val)
+ return ret_val;
+
+ ret_val = e1000_read_phy_reg(hw,
+ GG82563_PHY_SPEC_CTRL_2, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ phy_data &= ~GG82563_PSCR2_REVERSE_AUTO_NEG;
+ ret_val = e1000_write_phy_reg(hw,
+ GG82563_PHY_SPEC_CTRL_2, phy_data);
+
+ if (ret_val)
+ return ret_val;
+
+ reg_data = E1000_READ_REG(hw, CTRL_EXT);
+ reg_data &= ~(E1000_CTRL_EXT_LINK_MODE_MASK);
+ E1000_WRITE_REG(hw, CTRL_EXT, reg_data);
+
+ ret_val = e1000_read_phy_reg(hw,
+ GG82563_PHY_PWR_MGMT_CTRL, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ /* Do not init these registers when the HW is in IAMT mode, since the
+ * firmware will have already initialized them. We only initialize
+ * them if the HW is not in IAMT mode.
+ */
+ if (e1000_check_mng_mode(hw) == FALSE) {
+ /* Enable Electrical Idle on the PHY */
+ phy_data |= GG82563_PMCR_ENABLE_ELECTRICAL_IDLE;
+ ret_val = e1000_write_phy_reg(hw,
+ GG82563_PHY_PWR_MGMT_CTRL, phy_data);
+ if (ret_val)
+ return ret_val;
+
+ ret_val = e1000_read_phy_reg(hw,
+ GG82563_PHY_KMRN_MODE_CTRL, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ phy_data &= ~GG82563_KMCR_PASS_FALSE_CARRIER;
+ ret_val = e1000_write_phy_reg(hw,
+ GG82563_PHY_KMRN_MODE_CTRL, phy_data);
+
+ if (ret_val)
+ return ret_val;
+ }
+
+ /* Workaround: Disable padding in Kumeran interface in the MAC
+ * and in the PHY to avoid CRC errors.
+ */
+ ret_val = e1000_read_phy_reg(hw,
+ GG82563_PHY_INBAND_CTRL, &phy_data);
+ if (ret_val)
+ return ret_val;
+ phy_data |= GG82563_ICR_DIS_PADDING;
+ ret_val = e1000_write_phy_reg(hw,
+ GG82563_PHY_INBAND_CTRL, phy_data);
+ if (ret_val)
+ return ret_val;
+ }
+ return E1000_SUCCESS;
+}
+
+/********************************************************************
+* Copper link setup for e1000_phy_m88 series.
+*
+* hw - Struct containing variables accessed by shared code
+*********************************************************************/
+static int32_t
+e1000_copper_link_mgp_setup(struct e1000_hw *hw)
+{
+ int32_t ret_val;
+ uint16_t phy_data;
+
+ DEBUGFUNC();
+
+ if (hw->phy_reset_disable)
+ return E1000_SUCCESS;
+
+ /* Enable CRS on TX. This must be set for half-duplex operation. */
+ ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data);
+ if (ret_val)
+ return ret_val;
+
phy_data |= M88E1000_PSCR_ASSERT_CRS_ON_TX;
-#if 0
/* Options:
* MDI/MDI-X = 0 (default)
* 0 - Auto for all speeds
@@ -1210,6 +2750,7 @@ e1000_setup_copper_link(struct eth_device *nic)
* 3 - Auto for 1000Base-T only (MDI-X for 10/100Base-T modes)
*/
phy_data &= ~M88E1000_PSCR_AUTO_X_MODE;
+
switch (hw->mdix) {
case 1:
phy_data |= M88E1000_PSCR_MDI_MANUAL_MODE;
@@ -1225,68 +2766,75 @@ e1000_setup_copper_link(struct eth_device *nic)
phy_data |= M88E1000_PSCR_AUTO_X_MODE;
break;
}
-#else
- phy_data |= M88E1000_PSCR_AUTO_X_MODE;
-#endif
-#if 0
/* Options:
* disable_polarity_correction = 0 (default)
- * Automatic Correction for Reversed Cable Polarity
+ * Automatic Correction for Reversed Cable Polarity
* 0 - Disabled
* 1 - Enabled
*/
phy_data &= ~M88E1000_PSCR_POLARITY_REVERSAL;
- if (hw->disable_polarity_correction == 1)
- phy_data |= M88E1000_PSCR_POLARITY_REVERSAL;
-#else
- phy_data &= ~M88E1000_PSCR_POLARITY_REVERSAL;
-#endif
- if (e1000_write_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, phy_data) < 0) {
- DEBUGOUT("PHY Write Error\n");
- return -E1000_ERR_PHY;
- }
+ ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, phy_data);
+ if (ret_val)
+ return ret_val;
- /* Force TX_CLK in the Extended PHY Specific Control Register
- * to 25MHz clock.
- */
- if (e1000_read_phy_reg(hw, M88E1000_EXT_PHY_SPEC_CTRL, &phy_data) < 0) {
- DEBUGOUT("PHY Read Error\n");
- return -E1000_ERR_PHY;
- }
- phy_data |= M88E1000_EPSCR_TX_CLK_25;
- /* Configure Master and Slave downshift values */
- phy_data &= ~(M88E1000_EPSCR_MASTER_DOWNSHIFT_MASK |
- M88E1000_EPSCR_SLAVE_DOWNSHIFT_MASK);
- phy_data |= (M88E1000_EPSCR_MASTER_DOWNSHIFT_1X |
- M88E1000_EPSCR_SLAVE_DOWNSHIFT_1X);
- if (e1000_write_phy_reg(hw, M88E1000_EXT_PHY_SPEC_CTRL, phy_data) < 0) {
- DEBUGOUT("PHY Write Error\n");
- return -E1000_ERR_PHY;
+ if (hw->phy_revision < M88E1011_I_REV_4) {
+ /* Force TX_CLK in the Extended PHY Specific Control Register
+ * to 25MHz clock.
+ */
+ ret_val = e1000_read_phy_reg(hw,
+ M88E1000_EXT_PHY_SPEC_CTRL, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ phy_data |= M88E1000_EPSCR_TX_CLK_25;
+
+ if ((hw->phy_revision == E1000_REVISION_2) &&
+ (hw->phy_id == M88E1111_I_PHY_ID)) {
+ /* Vidalia Phy, set the downshift counter to 5x */
+ phy_data &= ~(M88EC018_EPSCR_DOWNSHIFT_COUNTER_MASK);
+ phy_data |= M88EC018_EPSCR_DOWNSHIFT_COUNTER_5X;
+ ret_val = e1000_write_phy_reg(hw,
+ M88E1000_EXT_PHY_SPEC_CTRL, phy_data);
+ if (ret_val)
+ return ret_val;
+ } else {
+ /* Configure Master and Slave downshift values */
+ phy_data &= ~(M88E1000_EPSCR_MASTER_DOWNSHIFT_MASK
+ | M88E1000_EPSCR_SLAVE_DOWNSHIFT_MASK);
+ phy_data |= (M88E1000_EPSCR_MASTER_DOWNSHIFT_1X
+ | M88E1000_EPSCR_SLAVE_DOWNSHIFT_1X);
+ ret_val = e1000_write_phy_reg(hw,
+ M88E1000_EXT_PHY_SPEC_CTRL, phy_data);
+ if (ret_val)
+ return ret_val;
+ }
}
/* SW Reset the PHY so all changes take effect */
ret_val = e1000_phy_reset(hw);
- if (ret_val < 0) {
+ if (ret_val) {
DEBUGOUT("Error Resetting the PHY\n");
return ret_val;
}
- /* Options:
- * autoneg = 1 (default)
- * PHY will advertise value(s) parsed from
- * autoneg_advertised and fc
- * autoneg = 0
- * PHY will be set to 10H, 10F, 100H, or 100F
- * depending on value parsed from forced_speed_duplex.
- */
+ return E1000_SUCCESS;
+}
+
+/********************************************************************
+* Setup auto-negotiation and flow control advertisements,
+* and then perform auto-negotiation.
+*
+* hw - Struct containing variables accessed by shared code
+*********************************************************************/
+static int32_t
+e1000_copper_link_autoneg(struct e1000_hw *hw)
+{
+ int32_t ret_val;
+ uint16_t phy_data;
+
+ DEBUGFUNC();
- /* Is autoneg enabled? This is enabled by default or by software override.
- * If so, call e1000_phy_setup_autoneg routine to parse the
- * autoneg_advertised and fc options. If autoneg is NOT enabled, then the
- * user should have provided a speed/duplex override. If so, then call
- * e1000_phy_force_speed_duplex to parse and set this up.
- */
/* Perform some bounds checking on the hw->autoneg_advertised
* parameter. If this variable is zero, then set it to the default.
*/
@@ -1298,9 +2846,13 @@ e1000_setup_copper_link(struct eth_device *nic)
if (hw->autoneg_advertised == 0)
hw->autoneg_advertised = AUTONEG_ADVERTISE_SPEED_DEFAULT;
+ /* IFE phy only supports 10/100 */
+ if (hw->phy_type == e1000_phy_ife)
+ hw->autoneg_advertised &= AUTONEG_ADVERTISE_10_100_ALL;
+
DEBUGOUT("Reconfiguring auto-neg advertisement params\n");
ret_val = e1000_phy_setup_autoneg(hw);
- if (ret_val < 0) {
+ if (ret_val) {
DEBUGOUT("Error Setting up Auto-Negotiation\n");
return ret_val;
}
@@ -1309,82 +2861,177 @@ e1000_setup_copper_link(struct eth_device *nic)
/* Restart auto-negotiation by setting the Auto Neg Enable bit and
* the Auto Neg Restart bit in the PHY control register.
*/
- if (e1000_read_phy_reg(hw, PHY_CTRL, &phy_data) < 0) {
- DEBUGOUT("PHY Read Error\n");
- return -E1000_ERR_PHY;
- }
+ ret_val = e1000_read_phy_reg(hw, PHY_CTRL, &phy_data);
+ if (ret_val)
+ return ret_val;
+
phy_data |= (MII_CR_AUTO_NEG_EN | MII_CR_RESTART_AUTO_NEG);
- if (e1000_write_phy_reg(hw, PHY_CTRL, phy_data) < 0) {
- DEBUGOUT("PHY Write Error\n");
- return -E1000_ERR_PHY;
- }
-#if 0
+ ret_val = e1000_write_phy_reg(hw, PHY_CTRL, phy_data);
+ if (ret_val)
+ return ret_val;
+
/* Does the user want to wait for Auto-Neg to complete here, or
* check at a later time (for example, callback routine).
*/
+ /* If we do not wait for autonegtation to complete I
+ * do not see a valid link status.
+ * wait_autoneg_complete = 1 .
+ */
if (hw->wait_autoneg_complete) {
ret_val = e1000_wait_autoneg(hw);
- if (ret_val < 0) {
- DEBUGOUT
- ("Error while waiting for autoneg to complete\n");
+ if (ret_val) {
+ DEBUGOUT("Error while waiting for autoneg"
+ "to complete\n");
return ret_val;
}
}
-#else
- /* If we do not wait for autonegtation to complete I
- * do not see a valid link status.
- */
- ret_val = e1000_wait_autoneg(hw);
- if (ret_val < 0) {
- DEBUGOUT("Error while waiting for autoneg to complete\n");
+
+ hw->get_link_status = TRUE;
+
+ return E1000_SUCCESS;
+}
+
+/******************************************************************************
+* Config the MAC and the PHY after link is up.
+* 1) Set up the MAC to the current PHY speed/duplex
+* if we are on 82543. If we
+* are on newer silicon, we only need to configure
+* collision distance in the Transmit Control Register.
+* 2) Set up flow control on the MAC to that established with
+* the link partner.
+* 3) Config DSP to improve Gigabit link quality for some PHY revisions.
+*
+* hw - Struct containing variables accessed by shared code
+******************************************************************************/
+static int32_t
+e1000_copper_link_postconfig(struct e1000_hw *hw)
+{
+ int32_t ret_val;
+ DEBUGFUNC();
+
+ if (hw->mac_type >= e1000_82544) {
+ e1000_config_collision_dist(hw);
+ } else {
+ ret_val = e1000_config_mac_to_phy(hw);
+ if (ret_val) {
+ DEBUGOUT("Error configuring MAC to PHY settings\n");
+ return ret_val;
+ }
+ }
+ ret_val = e1000_config_fc_after_link_up(hw);
+ if (ret_val) {
+ DEBUGOUT("Error Configuring Flow Control\n");
return ret_val;
}
-#endif
+ return E1000_SUCCESS;
+}
+
+/******************************************************************************
+* Detects which PHY is present and setup the speed and duplex
+*
+* hw - Struct containing variables accessed by shared code
+******************************************************************************/
+static int
+e1000_setup_copper_link(struct eth_device *nic)
+{
+ struct e1000_hw *hw = nic->priv;
+ int32_t ret_val;
+ uint16_t i;
+ uint16_t phy_data;
+ uint16_t reg_data;
+
+ DEBUGFUNC();
+
+ switch (hw->mac_type) {
+ case e1000_80003es2lan:
+ case e1000_ich8lan:
+ /* Set the mac to wait the maximum time between each
+ * iteration and increase the max iterations when
+ * polling the phy; this fixes erroneous timeouts at 10Mbps. */
+ ret_val = e1000_write_kmrn_reg(hw,
+ GG82563_REG(0x34, 4), 0xFFFF);
+ if (ret_val)
+ return ret_val;
+ ret_val = e1000_read_kmrn_reg(hw,
+ GG82563_REG(0x34, 9), &reg_data);
+ if (ret_val)
+ return ret_val;
+ reg_data |= 0x3F;
+ ret_val = e1000_write_kmrn_reg(hw,
+ GG82563_REG(0x34, 9), reg_data);
+ if (ret_val)
+ return ret_val;
+ default:
+ break;
+ }
+
+ /* Check if it is a valid PHY and set PHY mode if necessary. */
+ ret_val = e1000_copper_link_preconfig(hw);
+ if (ret_val)
+ return ret_val;
+ switch (hw->mac_type) {
+ case e1000_80003es2lan:
+ /* Kumeran registers are written-only */
+ reg_data =
+ E1000_KUMCTRLSTA_INB_CTRL_LINK_STATUS_TX_TIMEOUT_DEFAULT;
+ reg_data |= E1000_KUMCTRLSTA_INB_CTRL_DIS_PADDING;
+ ret_val = e1000_write_kmrn_reg(hw,
+ E1000_KUMCTRLSTA_OFFSET_INB_CTRL, reg_data);
+ if (ret_val)
+ return ret_val;
+ break;
+ default:
+ break;
+ }
+
+ if (hw->phy_type == e1000_phy_igp ||
+ hw->phy_type == e1000_phy_igp_3 ||
+ hw->phy_type == e1000_phy_igp_2) {
+ ret_val = e1000_copper_link_igp_setup(hw);
+ if (ret_val)
+ return ret_val;
+ } else if (hw->phy_type == e1000_phy_m88) {
+ ret_val = e1000_copper_link_mgp_setup(hw);
+ if (ret_val)
+ return ret_val;
+ } else if (hw->phy_type == e1000_phy_gg82563) {
+ ret_val = e1000_copper_link_ggp_setup(hw);
+ if (ret_val)
+ return ret_val;
+ }
+
+ /* always auto */
+ /* Setup autoneg and flow control advertisement
+ * and perform autonegotiation */
+ ret_val = e1000_copper_link_autoneg(hw);
+ if (ret_val)
+ return ret_val;
/* Check link status. Wait up to 100 microseconds for link to become
* valid.
*/
for (i = 0; i < 10; i++) {
- if (e1000_read_phy_reg(hw, PHY_STATUS, &phy_data) < 0) {
- DEBUGOUT("PHY Read Error\n");
- return -E1000_ERR_PHY;
- }
- if (e1000_read_phy_reg(hw, PHY_STATUS, &phy_data) < 0) {
- DEBUGOUT("PHY Read Error\n");
- return -E1000_ERR_PHY;
- }
+ ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data);
+ if (ret_val)
+ return ret_val;
+ ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data);
+ if (ret_val)
+ return ret_val;
+
if (phy_data & MII_SR_LINK_STATUS) {
- /* We have link, so we need to finish the config process:
- * 1) Set up the MAC to the current PHY speed/duplex
- * if we are on 82543. If we
- * are on newer silicon, we only need to configure
- * collision distance in the Transmit Control Register.
- * 2) Set up flow control on the MAC to that established with
- * the link partner.
- */
- if (hw->mac_type >= e1000_82544) {
- e1000_config_collision_dist(hw);
- } else {
- ret_val = e1000_config_mac_to_phy(hw);
- if (ret_val < 0) {
- DEBUGOUT
- ("Error configuring MAC to PHY settings\n");
- return ret_val;
- }
- }
- ret_val = e1000_config_fc_after_link_up(hw);
- if (ret_val < 0) {
- DEBUGOUT("Error Configuring Flow Control\n");
+ /* Config the MAC and PHY after link is up */
+ ret_val = e1000_copper_link_postconfig(hw);
+ if (ret_val)
return ret_val;
- }
+
DEBUGOUT("Valid link established!!!\n");
- return 0;
+ return E1000_SUCCESS;
}
udelay(10);
}
DEBUGOUT("Unable to establish link!!!\n");
- return -E1000_ERR_NOLINK;
+ return E1000_SUCCESS;
}
/******************************************************************************
@@ -1392,25 +3039,28 @@ e1000_setup_copper_link(struct eth_device *nic)
*
* hw - Struct containing variables accessed by shared code
******************************************************************************/
-static int
+int32_t
e1000_phy_setup_autoneg(struct e1000_hw *hw)
{
+ int32_t ret_val;
uint16_t mii_autoneg_adv_reg;
uint16_t mii_1000t_ctrl_reg;
DEBUGFUNC();
/* Read the MII Auto-Neg Advertisement Register (Address 4). */
- if (e1000_read_phy_reg(hw, PHY_AUTONEG_ADV, &mii_autoneg_adv_reg) < 0) {
- DEBUGOUT("PHY Read Error\n");
- return -E1000_ERR_PHY;
- }
+ ret_val = e1000_read_phy_reg(hw, PHY_AUTONEG_ADV, &mii_autoneg_adv_reg);
+ if (ret_val)
+ return ret_val;
- /* Read the MII 1000Base-T Control Register (Address 9). */
- if (e1000_read_phy_reg(hw, PHY_1000T_CTRL, &mii_1000t_ctrl_reg) < 0) {
- DEBUGOUT("PHY Read Error\n");
- return -E1000_ERR_PHY;
- }
+ if (hw->phy_type != e1000_phy_ife) {
+ /* Read the MII 1000Base-T Control Register (Address 9). */
+ ret_val = e1000_read_phy_reg(hw, PHY_1000T_CTRL,
+ &mii_1000t_ctrl_reg);
+ if (ret_val)
+ return ret_val;
+ } else
+ mii_1000t_ctrl_reg = 0;
/* Need to parse both autoneg_advertised and fc and set up
* the appropriate PHY registers. First we will parse for
@@ -1421,7 +3071,7 @@ e1000_phy_setup_autoneg(struct e1000_hw *hw)
/* First we clear all the 10/100 mb speed bits in the Auto-Neg
* Advertisement Register (Address 4) and the 1000 mb speed bits in
- * the 1000Base-T Control Register (Address 9).
+ * the 1000Base-T Control Register (Address 9).
*/
mii_autoneg_adv_reg &= ~REG4_SPEED_MASK;
mii_1000t_ctrl_reg &= ~REG9_SPEED_MASK;
@@ -1517,18 +3167,20 @@ e1000_phy_setup_autoneg(struct e1000_hw *hw)
return -E1000_ERR_CONFIG;
}
- if (e1000_write_phy_reg(hw, PHY_AUTONEG_ADV, mii_autoneg_adv_reg) < 0) {
- DEBUGOUT("PHY Write Error\n");
- return -E1000_ERR_PHY;
- }
+ ret_val = e1000_write_phy_reg(hw, PHY_AUTONEG_ADV, mii_autoneg_adv_reg);
+ if (ret_val)
+ return ret_val;
DEBUGOUT("Auto-Neg Advertising %x\n", mii_autoneg_adv_reg);
- if (e1000_write_phy_reg(hw, PHY_1000T_CTRL, mii_1000t_ctrl_reg) < 0) {
- DEBUGOUT("PHY Write Error\n");
- return -E1000_ERR_PHY;
+ if (hw->phy_type != e1000_phy_ife) {
+ ret_val = e1000_write_phy_reg(hw, PHY_1000T_CTRL,
+ mii_1000t_ctrl_reg);
+ if (ret_val)
+ return ret_val;
}
- return 0;
+
+ return E1000_SUCCESS;
}
/******************************************************************************
@@ -1542,12 +3194,19 @@ e1000_phy_setup_autoneg(struct e1000_hw *hw)
static void
e1000_config_collision_dist(struct e1000_hw *hw)
{
- uint32_t tctl;
+ uint32_t tctl, coll_dist;
+
+ DEBUGFUNC();
+
+ if (hw->mac_type < e1000_82543)
+ coll_dist = E1000_COLLISION_DISTANCE_82542;
+ else
+ coll_dist = E1000_COLLISION_DISTANCE;
tctl = E1000_READ_REG(hw, TCTL);
tctl &= ~E1000_TCTL_COLD;
- tctl |= E1000_COLLISION_DISTANCE << E1000_COLD_SHIFT;
+ tctl |= coll_dist << E1000_COLD_SHIFT;
E1000_WRITE_REG(hw, TCTL, tctl);
E1000_WRITE_FLUSH(hw);
@@ -1681,7 +3340,7 @@ e1000_force_mac_fc(struct e1000_hw *hw)
* based on the flow control negotiated by the PHY. In TBI mode, the TFCE
* and RFCE bits will be automaticaly set to the negotiated flow control mode.
*****************************************************************************/
-static int
+static int32_t
e1000_config_fc_after_link_up(struct e1000_hw *hw)
{
int32_t ret_val;
@@ -1697,7 +3356,11 @@ e1000_config_fc_after_link_up(struct e1000_hw *hw)
* so we had to force link. In this case, we need to force the
* configuration of the MAC to match the "fc" parameter.
*/
- if ((hw->media_type == e1000_media_type_fiber) && (hw->autoneg_failed)) {
+ if (((hw->media_type == e1000_media_type_fiber) && (hw->autoneg_failed))
+ || ((hw->media_type == e1000_media_type_internal_serdes)
+ && (hw->autoneg_failed))
+ || ((hw->media_type == e1000_media_type_copper)
+ && (!hw->autoneg))) {
ret_val = e1000_force_mac_fc(hw);
if (ret_val < 0) {
DEBUGOUT("Error forcing flow control settings\n");
@@ -1881,7 +3544,7 @@ e1000_config_fc_after_link_up(struct e1000_hw *hw)
("Copper PHY and Auto Neg has not completed.\r\n");
}
}
- return 0;
+ return E1000_SUCCESS;
}
/******************************************************************************
@@ -2070,17 +3733,92 @@ e1000_check_for_link(struct eth_device *nic)
}
/******************************************************************************
+* Configure the MAC-to-PHY interface for 10/100Mbps
+*
+* hw - Struct containing variables accessed by shared code
+******************************************************************************/
+static int32_t
+e1000_configure_kmrn_for_10_100(struct e1000_hw *hw, uint16_t duplex)
+{
+ int32_t ret_val = E1000_SUCCESS;
+ uint32_t tipg;
+ uint16_t reg_data;
+
+ DEBUGFUNC();
+
+ reg_data = E1000_KUMCTRLSTA_HD_CTRL_10_100_DEFAULT;
+ ret_val = e1000_write_kmrn_reg(hw,
+ E1000_KUMCTRLSTA_OFFSET_HD_CTRL, reg_data);
+ if (ret_val)
+ return ret_val;
+
+ /* Configure Transmit Inter-Packet Gap */
+ tipg = E1000_READ_REG(hw, TIPG);
+ tipg &= ~E1000_TIPG_IPGT_MASK;
+ tipg |= DEFAULT_80003ES2LAN_TIPG_IPGT_10_100;
+ E1000_WRITE_REG(hw, TIPG, tipg);
+
+ ret_val = e1000_read_phy_reg(hw, GG82563_PHY_KMRN_MODE_CTRL, &reg_data);
+
+ if (ret_val)
+ return ret_val;
+
+ if (duplex == HALF_DUPLEX)
+ reg_data |= GG82563_KMCR_PASS_FALSE_CARRIER;
+ else
+ reg_data &= ~GG82563_KMCR_PASS_FALSE_CARRIER;
+
+ ret_val = e1000_write_phy_reg(hw, GG82563_PHY_KMRN_MODE_CTRL, reg_data);
+
+ return ret_val;
+}
+
+static int32_t
+e1000_configure_kmrn_for_1000(struct e1000_hw *hw)
+{
+ int32_t ret_val = E1000_SUCCESS;
+ uint16_t reg_data;
+ uint32_t tipg;
+
+ DEBUGFUNC();
+
+ reg_data = E1000_KUMCTRLSTA_HD_CTRL_1000_DEFAULT;
+ ret_val = e1000_write_kmrn_reg(hw,
+ E1000_KUMCTRLSTA_OFFSET_HD_CTRL, reg_data);
+ if (ret_val)
+ return ret_val;
+
+ /* Configure Transmit Inter-Packet Gap */
+ tipg = E1000_READ_REG(hw, TIPG);
+ tipg &= ~E1000_TIPG_IPGT_MASK;
+ tipg |= DEFAULT_80003ES2LAN_TIPG_IPGT_1000;
+ E1000_WRITE_REG(hw, TIPG, tipg);
+
+ ret_val = e1000_read_phy_reg(hw, GG82563_PHY_KMRN_MODE_CTRL, &reg_data);
+
+ if (ret_val)
+ return ret_val;
+
+ reg_data &= ~GG82563_KMCR_PASS_FALSE_CARRIER;
+ ret_val = e1000_write_phy_reg(hw, GG82563_PHY_KMRN_MODE_CTRL, reg_data);
+
+ return ret_val;
+}
+
+/******************************************************************************
* Detects the current speed and duplex settings of the hardware.
*
* hw - Struct containing variables accessed by shared code
* speed - Speed of the connection
* duplex - Duplex setting of the connection
*****************************************************************************/
-static void
-e1000_get_speed_and_duplex(struct e1000_hw *hw,
- uint16_t * speed, uint16_t * duplex)
+static int
+e1000_get_speed_and_duplex(struct e1000_hw *hw, uint16_t *speed,
+ uint16_t *duplex)
{
uint32_t status;
+ int32_t ret_val;
+ uint16_t phy_data;
DEBUGFUNC();
@@ -2109,6 +3847,41 @@ e1000_get_speed_and_duplex(struct e1000_hw *hw,
*speed = SPEED_1000;
*duplex = FULL_DUPLEX;
}
+
+ /* IGP01 PHY may advertise full duplex operation after speed downgrade
+ * even if it is operating at half duplex. Here we set the duplex
+ * settings to match the duplex in the link partner's capabilities.
+ */
+ if (hw->phy_type == e1000_phy_igp && hw->speed_downgraded) {
+ ret_val = e1000_read_phy_reg(hw, PHY_AUTONEG_EXP, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ if (!(phy_data & NWAY_ER_LP_NWAY_CAPS))
+ *duplex = HALF_DUPLEX;
+ else {
+ ret_val = e1000_read_phy_reg(hw,
+ PHY_LP_ABILITY, &phy_data);
+ if (ret_val)
+ return ret_val;
+ if ((*speed == SPEED_100 &&
+ !(phy_data & NWAY_LPAR_100TX_FD_CAPS))
+ || (*speed == SPEED_10
+ && !(phy_data & NWAY_LPAR_10T_FD_CAPS)))
+ *duplex = HALF_DUPLEX;
+ }
+ }
+
+ if ((hw->mac_type == e1000_80003es2lan) &&
+ (hw->media_type == e1000_media_type_copper)) {
+ if (*speed == SPEED_1000)
+ ret_val = e1000_configure_kmrn_for_1000(hw);
+ else
+ ret_val = e1000_configure_kmrn_for_10_100(hw, *duplex);
+ if (ret_val)
+ return ret_val;
+ }
+ return E1000_SUCCESS;
}
/******************************************************************************
@@ -2429,30 +4202,132 @@ e1000_write_phy_reg(struct e1000_hw *hw, uint32_t reg_addr, uint16_t phy_data)
}
/******************************************************************************
+ * Checks if PHY reset is blocked due to SOL/IDER session, for example.
+ * Returning E1000_BLK_PHY_RESET isn't necessarily an error. But it's up to
+ * the caller to figure out how to deal with it.
+ *
+ * hw - Struct containing variables accessed by shared code
+ *
+ * returns: - E1000_BLK_PHY_RESET
+ * E1000_SUCCESS
+ *
+ *****************************************************************************/
+int32_t
+e1000_check_phy_reset_block(struct e1000_hw *hw)
+{
+ uint32_t manc = 0;
+ uint32_t fwsm = 0;
+
+ if (hw->mac_type == e1000_ich8lan) {
+ fwsm = E1000_READ_REG(hw, FWSM);
+ return (fwsm & E1000_FWSM_RSPCIPHY) ? E1000_SUCCESS
+ : E1000_BLK_PHY_RESET;
+ }
+
+ if (hw->mac_type > e1000_82547_rev_2)
+ manc = E1000_READ_REG(hw, MANC);
+ return (manc & E1000_MANC_BLK_PHY_RST_ON_IDE) ?
+ E1000_BLK_PHY_RESET : E1000_SUCCESS;
+}
+
+/***************************************************************************
+ * Checks if the PHY configuration is done
+ *
+ * hw: Struct containing variables accessed by shared code
+ *
+ * returns: - E1000_ERR_RESET if fail to reset MAC
+ * E1000_SUCCESS at any other case.
+ *
+ ***************************************************************************/
+static int32_t
+e1000_get_phy_cfg_done(struct e1000_hw *hw)
+{
+ int32_t timeout = PHY_CFG_TIMEOUT;
+ uint32_t cfg_mask = E1000_EEPROM_CFG_DONE;
+
+ DEBUGFUNC();
+
+ switch (hw->mac_type) {
+ default:
+ mdelay(10);
+ break;
+ case e1000_80003es2lan:
+ /* Separate *_CFG_DONE_* bit for each port */
+ if (E1000_READ_REG(hw, STATUS) & E1000_STATUS_FUNC_1)
+ cfg_mask = E1000_EEPROM_CFG_DONE_PORT_1;
+ /* Fall Through */
+ case e1000_82571:
+ case e1000_82572:
+ while (timeout) {
+ if (E1000_READ_REG(hw, EEMNGCTL) & cfg_mask)
+ break;
+ else
+ mdelay(1);
+ timeout--;
+ }
+ if (!timeout) {
+ DEBUGOUT("MNG configuration cycle has not "
+ "completed.\n");
+ return -E1000_ERR_RESET;
+ }
+ break;
+ }
+
+ return E1000_SUCCESS;
+}
+
+/******************************************************************************
* Returns the PHY to the power-on reset state
*
* hw - Struct containing variables accessed by shared code
******************************************************************************/
-static void
+int32_t
e1000_phy_hw_reset(struct e1000_hw *hw)
{
- uint32_t ctrl;
- uint32_t ctrl_ext;
+ uint32_t ctrl, ctrl_ext;
+ uint32_t led_ctrl;
+ int32_t ret_val;
+ uint16_t swfw;
DEBUGFUNC();
+ /* In the case of the phy reset being blocked, it's not an error, we
+ * simply return success without performing the reset. */
+ ret_val = e1000_check_phy_reset_block(hw);
+ if (ret_val)
+ return E1000_SUCCESS;
+
DEBUGOUT("Resetting Phy...\n");
if (hw->mac_type > e1000_82543) {
+ if ((hw->mac_type == e1000_80003es2lan) &&
+ (E1000_READ_REG(hw, STATUS) & E1000_STATUS_FUNC_1)) {
+ swfw = E1000_SWFW_PHY1_SM;
+ } else {
+ swfw = E1000_SWFW_PHY0_SM;
+ }
+ if (e1000_swfw_sync_acquire(hw, swfw)) {
+ DEBUGOUT("Unable to acquire swfw sync\n");
+ return -E1000_ERR_SWFW_SYNC;
+ }
/* Read the device control register and assert the E1000_CTRL_PHY_RST
* bit. Then, take it out of reset.
*/
ctrl = E1000_READ_REG(hw, CTRL);
E1000_WRITE_REG(hw, CTRL, ctrl | E1000_CTRL_PHY_RST);
E1000_WRITE_FLUSH(hw);
- mdelay(10);
+
+ if (hw->mac_type < e1000_82571)
+ udelay(10);
+ else
+ udelay(100);
+
E1000_WRITE_REG(hw, CTRL, ctrl);
E1000_WRITE_FLUSH(hw);
+
+ if (hw->mac_type >= e1000_82571)
+ mdelay(10);
+
} else {
/* Read the Extended Device Control Register, assert the PHY_RESET_DIR
* bit to put the PHY into reset. Then, take it out of reset.
@@ -2468,6 +4343,127 @@ e1000_phy_hw_reset(struct e1000_hw *hw)
E1000_WRITE_FLUSH(hw);
}
udelay(150);
+
+ if ((hw->mac_type == e1000_82541) || (hw->mac_type == e1000_82547)) {
+ /* Configure activity LED after PHY reset */
+ led_ctrl = E1000_READ_REG(hw, LEDCTL);
+ led_ctrl &= IGP_ACTIVITY_LED_MASK;
+ led_ctrl |= (IGP_ACTIVITY_LED_ENABLE | IGP_LED3_MODE);
+ E1000_WRITE_REG(hw, LEDCTL, led_ctrl);
+ }
+
+ /* Wait for FW to finish PHY configuration. */
+ ret_val = e1000_get_phy_cfg_done(hw);
+ if (ret_val != E1000_SUCCESS)
+ return ret_val;
+
+ return ret_val;
+}
+
+/******************************************************************************
+ * IGP phy init script - initializes the GbE PHY
+ *
+ * hw - Struct containing variables accessed by shared code
+ *****************************************************************************/
+static void
+e1000_phy_init_script(struct e1000_hw *hw)
+{
+ uint32_t ret_val;
+ uint16_t phy_saved_data;
+ DEBUGFUNC();
+
+ if (hw->phy_init_script) {
+ mdelay(20);
+
+ /* Save off the current value of register 0x2F5B to be
+ * restored at the end of this routine. */
+ ret_val = e1000_read_phy_reg(hw, 0x2F5B, &phy_saved_data);
+
+ /* Disabled the PHY transmitter */
+ e1000_write_phy_reg(hw, 0x2F5B, 0x0003);
+
+ mdelay(20);
+
+ e1000_write_phy_reg(hw, 0x0000, 0x0140);
+
+ mdelay(5);
+
+ switch (hw->mac_type) {
+ case e1000_82541:
+ case e1000_82547:
+ e1000_write_phy_reg(hw, 0x1F95, 0x0001);
+
+ e1000_write_phy_reg(hw, 0x1F71, 0xBD21);
+
+ e1000_write_phy_reg(hw, 0x1F79, 0x0018);
+
+ e1000_write_phy_reg(hw, 0x1F30, 0x1600);
+
+ e1000_write_phy_reg(hw, 0x1F31, 0x0014);
+
+ e1000_write_phy_reg(hw, 0x1F32, 0x161C);
+
+ e1000_write_phy_reg(hw, 0x1F94, 0x0003);
+
+ e1000_write_phy_reg(hw, 0x1F96, 0x003F);
+
+ e1000_write_phy_reg(hw, 0x2010, 0x0008);
+ break;
+
+ case e1000_82541_rev_2:
+ case e1000_82547_rev_2:
+ e1000_write_phy_reg(hw, 0x1F73, 0x0099);
+ break;
+ default:
+ break;
+ }
+
+ e1000_write_phy_reg(hw, 0x0000, 0x3300);
+
+ mdelay(20);
+
+ /* Now enable the transmitter */
+ e1000_write_phy_reg(hw, 0x2F5B, phy_saved_data);
+
+ if (hw->mac_type == e1000_82547) {
+ uint16_t fused, fine, coarse;
+
+ /* Move to analog registers page */
+ e1000_read_phy_reg(hw,
+ IGP01E1000_ANALOG_SPARE_FUSE_STATUS, &fused);
+
+ if (!(fused & IGP01E1000_ANALOG_SPARE_FUSE_ENABLED)) {
+ e1000_read_phy_reg(hw,
+ IGP01E1000_ANALOG_FUSE_STATUS, &fused);
+
+ fine = fused & IGP01E1000_ANALOG_FUSE_FINE_MASK;
+ coarse = fused
+ & IGP01E1000_ANALOG_FUSE_COARSE_MASK;
+
+ if (coarse >
+ IGP01E1000_ANALOG_FUSE_COARSE_THRESH) {
+ coarse -=
+ IGP01E1000_ANALOG_FUSE_COARSE_10;
+ fine -= IGP01E1000_ANALOG_FUSE_FINE_1;
+ } else if (coarse
+ == IGP01E1000_ANALOG_FUSE_COARSE_THRESH)
+ fine -= IGP01E1000_ANALOG_FUSE_FINE_10;
+
+ fused = (fused
+ & IGP01E1000_ANALOG_FUSE_POLY_MASK) |
+ (fine
+ & IGP01E1000_ANALOG_FUSE_FINE_MASK) |
+ (coarse
+ & IGP01E1000_ANALOG_FUSE_COARSE_MASK);
+
+ e1000_write_phy_reg(hw,
+ IGP01E1000_ANALOG_FUSE_CONTROL, fused);
+ e1000_write_phy_reg(hw,
+ IGP01E1000_ANALOG_FUSE_BYPASS,
+ IGP01E1000_ANALOG_FUSE_ENABLE_SW_CONTROL);
+ }
+ }
+ }
}
/******************************************************************************
@@ -2475,26 +4471,49 @@ e1000_phy_hw_reset(struct e1000_hw *hw)
*
* hw - Struct containing variables accessed by shared code
*
-* Sets bit 15 of the MII Control regiser
+* Sets bit 15 of the MII Control register
******************************************************************************/
-static int
+int32_t
e1000_phy_reset(struct e1000_hw *hw)
{
+ int32_t ret_val;
uint16_t phy_data;
DEBUGFUNC();
- if (e1000_read_phy_reg(hw, PHY_CTRL, &phy_data) < 0) {
- DEBUGOUT("PHY Read Error\n");
- return -E1000_ERR_PHY;
- }
- phy_data |= MII_CR_RESET;
- if (e1000_write_phy_reg(hw, PHY_CTRL, phy_data) < 0) {
- DEBUGOUT("PHY Write Error\n");
- return -E1000_ERR_PHY;
+ /* In the case of the phy reset being blocked, it's not an error, we
+ * simply return success without performing the reset. */
+ ret_val = e1000_check_phy_reset_block(hw);
+ if (ret_val)
+ return E1000_SUCCESS;
+
+ switch (hw->phy_type) {
+ case e1000_phy_igp:
+ case e1000_phy_igp_2:
+ case e1000_phy_igp_3:
+ case e1000_phy_ife:
+ ret_val = e1000_phy_hw_reset(hw);
+ if (ret_val)
+ return ret_val;
+ break;
+ default:
+ ret_val = e1000_read_phy_reg(hw, PHY_CTRL, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ phy_data |= MII_CR_RESET;
+ ret_val = e1000_write_phy_reg(hw, PHY_CTRL, phy_data);
+ if (ret_val)
+ return ret_val;
+
+ udelay(1);
+ break;
}
- udelay(1);
- return 0;
+
+ if (hw->phy_type == e1000_phy_igp || hw->phy_type == e1000_phy_igp_2)
+ e1000_phy_init_script(hw);
+
+ return E1000_SUCCESS;
}
static int e1000_set_phy_type (struct e1000_hw *hw)
@@ -2508,14 +4527,31 @@ static int e1000_set_phy_type (struct e1000_hw *hw)
case M88E1000_E_PHY_ID:
case M88E1000_I_PHY_ID:
case M88E1011_I_PHY_ID:
+ case M88E1111_I_PHY_ID:
hw->phy_type = e1000_phy_m88;
break;
case IGP01E1000_I_PHY_ID:
if (hw->mac_type == e1000_82541 ||
- hw->mac_type == e1000_82541_rev_2) {
+ hw->mac_type == e1000_82541_rev_2 ||
+ hw->mac_type == e1000_82547 ||
+ hw->mac_type == e1000_82547_rev_2) {
+ hw->phy_type = e1000_phy_igp;
hw->phy_type = e1000_phy_igp;
break;
}
+ case IGP03E1000_E_PHY_ID:
+ hw->phy_type = e1000_phy_igp_3;
+ break;
+ case IFE_E_PHY_ID:
+ case IFE_PLUS_E_PHY_ID:
+ case IFE_C_E_PHY_ID:
+ hw->phy_type = e1000_phy_ife;
+ break;
+ case GG82563_E_PHY_ID:
+ if (hw->mac_type == e1000_80003es2lan) {
+ hw->phy_type = e1000_phy_gg82563;
+ break;
+ }
/* Fall Through */
default:
/* Should never have loaded on this device */
@@ -2531,27 +4567,47 @@ static int e1000_set_phy_type (struct e1000_hw *hw)
*
* hw - Struct containing variables accessed by shared code
******************************************************************************/
-static int
+static int32_t
e1000_detect_gig_phy(struct e1000_hw *hw)
{
- int32_t phy_init_status;
+ int32_t phy_init_status, ret_val;
uint16_t phy_id_high, phy_id_low;
- int match = FALSE;
+ boolean_t match = FALSE;
DEBUGFUNC();
- /* Read the PHY ID Registers to identify which PHY is onboard. */
- if (e1000_read_phy_reg(hw, PHY_ID1, &phy_id_high) < 0) {
- DEBUGOUT("PHY Read Error\n");
- return -E1000_ERR_PHY;
+ /* The 82571 firmware may still be configuring the PHY. In this
+ * case, we cannot access the PHY until the configuration is done. So
+ * we explicitly set the PHY values. */
+ if (hw->mac_type == e1000_82571 ||
+ hw->mac_type == e1000_82572) {
+ hw->phy_id = IGP01E1000_I_PHY_ID;
+ hw->phy_type = e1000_phy_igp_2;
+ return E1000_SUCCESS;
}
+
+ /* ESB-2 PHY reads require e1000_phy_gg82563 to be set because of a
+ * work- around that forces PHY page 0 to be set or the reads fail.
+ * The rest of the code in this routine uses e1000_read_phy_reg to
+ * read the PHY ID. So for ESB-2 we need to have this set so our
+ * reads won't fail. If the attached PHY is not a e1000_phy_gg82563,
+ * the routines below will figure this out as well. */
+ if (hw->mac_type == e1000_80003es2lan)
+ hw->phy_type = e1000_phy_gg82563;
+
+ /* Read the PHY ID Registers to identify which PHY is onboard. */
+ ret_val = e1000_read_phy_reg(hw, PHY_ID1, &phy_id_high);
+ if (ret_val)
+ return ret_val;
+
hw->phy_id = (uint32_t) (phy_id_high << 16);
- udelay(2);
- if (e1000_read_phy_reg(hw, PHY_ID2, &phy_id_low) < 0) {
- DEBUGOUT("PHY Read Error\n");
- return -E1000_ERR_PHY;
- }
+ udelay(20);
+ ret_val = e1000_read_phy_reg(hw, PHY_ID2, &phy_id_low);
+ if (ret_val)
+ return ret_val;
+
hw->phy_id |= (uint32_t) (phy_id_low & PHY_REVISION_MASK);
+ hw->phy_revision = (uint32_t) phy_id_low & ~PHY_REVISION_MASK;
switch (hw->mac_type) {
case e1000_82543:
@@ -2564,15 +4620,38 @@ e1000_detect_gig_phy(struct e1000_hw *hw)
break;
case e1000_82540:
case e1000_82545:
+ case e1000_82545_rev_3:
case e1000_82546:
+ case e1000_82546_rev_3:
if (hw->phy_id == M88E1011_I_PHY_ID)
match = TRUE;
break;
+ case e1000_82541:
case e1000_82541_rev_2:
+ case e1000_82547:
+ case e1000_82547_rev_2:
if(hw->phy_id == IGP01E1000_I_PHY_ID)
match = TRUE;
break;
+ case e1000_82573:
+ if (hw->phy_id == M88E1111_I_PHY_ID)
+ match = TRUE;
+ break;
+ case e1000_80003es2lan:
+ if (hw->phy_id == GG82563_E_PHY_ID)
+ match = TRUE;
+ break;
+ case e1000_ich8lan:
+ if (hw->phy_id == IGP03E1000_E_PHY_ID)
+ match = TRUE;
+ if (hw->phy_id == IFE_E_PHY_ID)
+ match = TRUE;
+ if (hw->phy_id == IFE_PLUS_E_PHY_ID)
+ match = TRUE;
+ if (hw->phy_id == IFE_C_E_PHY_ID)
+ match = TRUE;
+ break;
default:
DEBUGOUT("Invalid MAC type %d\n", hw->mac_type);
return -E1000_ERR_CONFIG;
@@ -2588,6 +4667,60 @@ e1000_detect_gig_phy(struct e1000_hw *hw)
return -E1000_ERR_PHY;
}
+/*****************************************************************************
+ * Set media type and TBI compatibility.
+ *
+ * hw - Struct containing variables accessed by shared code
+ * **************************************************************************/
+void
+e1000_set_media_type(struct e1000_hw *hw)
+{
+ uint32_t status;
+
+ DEBUGFUNC();
+
+ if (hw->mac_type != e1000_82543) {
+ /* tbi_compatibility is only valid on 82543 */
+ hw->tbi_compatibility_en = FALSE;
+ }
+
+ switch (hw->device_id) {
+ case E1000_DEV_ID_82545GM_SERDES:
+ case E1000_DEV_ID_82546GB_SERDES:
+ case E1000_DEV_ID_82571EB_SERDES:
+ case E1000_DEV_ID_82571EB_SERDES_DUAL:
+ case E1000_DEV_ID_82571EB_SERDES_QUAD:
+ case E1000_DEV_ID_82572EI_SERDES:
+ case E1000_DEV_ID_80003ES2LAN_SERDES_DPT:
+ hw->media_type = e1000_media_type_internal_serdes;
+ break;
+ default:
+ switch (hw->mac_type) {
+ case e1000_82542_rev2_0:
+ case e1000_82542_rev2_1:
+ hw->media_type = e1000_media_type_fiber;
+ break;
+ case e1000_ich8lan:
+ case e1000_82573:
+ /* The STATUS_TBIMODE bit is reserved or reused
+ * for the this device.
+ */
+ hw->media_type = e1000_media_type_copper;
+ break;
+ default:
+ status = E1000_READ_REG(hw, STATUS);
+ if (status & E1000_STATUS_TBIMODE) {
+ hw->media_type = e1000_media_type_fiber;
+ /* tbi_compatibility not valid on fiber */
+ hw->tbi_compatibility_en = FALSE;
+ } else {
+ hw->media_type = e1000_media_type_copper;
+ }
+ break;
+ }
+ }
+}
+
/**
* e1000_sw_init - Initialize general software structures (struct e1000_adapter)
*
@@ -2619,6 +4752,17 @@ e1000_sw_init(struct eth_device *nic, int cardnum)
return result;
}
+ switch (hw->mac_type) {
+ default:
+ break;
+ case e1000_82541:
+ case e1000_82547:
+ case e1000_82541_rev_2:
+ case e1000_82547_rev_2:
+ hw->phy_init_script = 1;
+ break;
+ }
+
/* lan a vs. lan b settings */
if (hw->mac_type == e1000_82546)
/*this also works w/ multiple 82546 cards */
@@ -2634,6 +4778,7 @@ e1000_sw_init(struct eth_device *nic, int cardnum)
hw->fc_send_xon = 1;
/* Media type - copper or fiber */
+ e1000_set_media_type(hw);
if (hw->mac_type >= e1000_82543) {
uint32_t status = E1000_READ_REG(hw, STATUS);
@@ -2649,22 +4794,13 @@ e1000_sw_init(struct eth_device *nic, int cardnum)
hw->media_type = e1000_media_type_fiber;
}
+ hw->tbi_compatibility_en = TRUE;
+ hw->wait_autoneg_complete = TRUE;
if (hw->mac_type < e1000_82543)
hw->report_tx_early = 0;
else
hw->report_tx_early = 1;
- hw->tbi_compatibility_en = TRUE;
-#if 0
- hw->wait_autoneg_complete = FALSE;
- hw->adaptive_ifs = TRUE;
-
- /* Copper options */
- if (hw->media_type == e1000_media_type_copper) {
- hw->mdix = AUTO_ALL_MODES;
- hw->disable_polarity_correction = FALSE;
- }
-#endif
return E1000_SUCCESS;
}
@@ -2693,7 +4829,8 @@ e1000_configure_tx(struct e1000_hw *hw)
{
unsigned long ptr;
unsigned long tctl;
- unsigned long tipg;
+ unsigned long tipg, tarc;
+ uint32_t ipgr1, ipgr2;
ptr = (u32) tx_pool;
if (ptr & 0xf)
@@ -2712,45 +4849,64 @@ e1000_configure_tx(struct e1000_hw *hw)
tx_tail = 0;
/* Set the default values for the Tx Inter Packet Gap timer */
+ if (hw->mac_type <= e1000_82547_rev_2 &&
+ (hw->media_type == e1000_media_type_fiber ||
+ hw->media_type == e1000_media_type_internal_serdes))
+ tipg = DEFAULT_82543_TIPG_IPGT_FIBER;
+ else
+ tipg = DEFAULT_82543_TIPG_IPGT_COPPER;
+
+ /* Set the default values for the Tx Inter Packet Gap timer */
switch (hw->mac_type) {
case e1000_82542_rev2_0:
case e1000_82542_rev2_1:
tipg = DEFAULT_82542_TIPG_IPGT;
- tipg |= DEFAULT_82542_TIPG_IPGR1 << E1000_TIPG_IPGR1_SHIFT;
- tipg |= DEFAULT_82542_TIPG_IPGR2 << E1000_TIPG_IPGR2_SHIFT;
+ ipgr1 = DEFAULT_82542_TIPG_IPGR1;
+ ipgr2 = DEFAULT_82542_TIPG_IPGR2;
+ break;
+ case e1000_80003es2lan:
+ ipgr1 = DEFAULT_82543_TIPG_IPGR1;
+ ipgr2 = DEFAULT_80003ES2LAN_TIPG_IPGR2;
break;
default:
- if (hw->media_type == e1000_media_type_fiber)
- tipg = DEFAULT_82543_TIPG_IPGT_FIBER;
- else
- tipg = DEFAULT_82543_TIPG_IPGT_COPPER;
- tipg |= DEFAULT_82543_TIPG_IPGR1 << E1000_TIPG_IPGR1_SHIFT;
- tipg |= DEFAULT_82543_TIPG_IPGR2 << E1000_TIPG_IPGR2_SHIFT;
+ ipgr1 = DEFAULT_82543_TIPG_IPGR1;
+ ipgr2 = DEFAULT_82543_TIPG_IPGR2;
+ break;
}
+ tipg |= ipgr1 << E1000_TIPG_IPGR1_SHIFT;
+ tipg |= ipgr2 << E1000_TIPG_IPGR2_SHIFT;
E1000_WRITE_REG(hw, TIPG, tipg);
-#if 0
- /* Set the Tx Interrupt Delay register */
- E1000_WRITE_REG(hw, TIDV, adapter->tx_int_delay);
- if (hw->mac_type >= e1000_82540)
- E1000_WRITE_REG(hw, TADV, adapter->tx_abs_int_delay);
-#endif
/* Program the Transmit Control Register */
tctl = E1000_READ_REG(hw, TCTL);
tctl &= ~E1000_TCTL_CT;
tctl |= E1000_TCTL_EN | E1000_TCTL_PSP |
(E1000_COLLISION_THRESHOLD << E1000_CT_SHIFT);
- E1000_WRITE_REG(hw, TCTL, tctl);
+
+ if (hw->mac_type == e1000_82571 || hw->mac_type == e1000_82572) {
+ tarc = E1000_READ_REG(hw, TARC0);
+ /* set the speed mode bit, we'll clear it if we're not at
+ * gigabit link later */
+ /* git bit can be set to 1*/
+ } else if (hw->mac_type == e1000_80003es2lan) {
+ tarc = E1000_READ_REG(hw, TARC0);
+ tarc |= 1;
+ E1000_WRITE_REG(hw, TARC0, tarc);
+ tarc = E1000_READ_REG(hw, TARC1);
+ tarc |= 1;
+ E1000_WRITE_REG(hw, TARC1, tarc);
+ }
+
e1000_config_collision_dist(hw);
-#if 0
- /* Setup Transmit Descriptor Settings for this adapter */
- adapter->txd_cmd = E1000_TXD_CMD_IFCS | E1000_TXD_CMD_IDE;
+ /* Setup Transmit Descriptor Settings for eop descriptor */
+ hw->txd_cmd = E1000_TXD_CMD_EOP | E1000_TXD_CMD_IFCS;
- if (adapter->hw.report_tx_early == 1)
- adapter->txd_cmd |= E1000_TXD_CMD_RS;
+ /* Need to set up RS bit */
+ if (hw->mac_type < e1000_82543)
+ hw->txd_cmd |= E1000_TXD_CMD_RPS;
else
- adapter->txd_cmd |= E1000_TXD_CMD_RPS;
-#endif
+ hw->txd_cmd |= E1000_TXD_CMD_RS;
+ E1000_WRITE_REG(hw, TCTL, tctl);
}
/**
@@ -2766,8 +4922,9 @@ e1000_setup_rctl(struct e1000_hw *hw)
rctl &= ~(3 << E1000_RCTL_MO_SHIFT);
- rctl |= E1000_RCTL_EN | E1000_RCTL_BAM | E1000_RCTL_LBM_NO | E1000_RCTL_RDMTS_HALF; /* |
- (hw.mc_filter_type << E1000_RCTL_MO_SHIFT); */
+ rctl |= E1000_RCTL_EN | E1000_RCTL_BAM | E1000_RCTL_LBM_NO
+ | E1000_RCTL_RDMTS_HALF; /* |
+ (hw.mc_filter_type << E1000_RCTL_MO_SHIFT); */
if (hw->tbi_compatibility_on == 1)
rctl |= E1000_RCTL_SBP;
@@ -2775,26 +4932,8 @@ e1000_setup_rctl(struct e1000_hw *hw)
rctl &= ~E1000_RCTL_SBP;
rctl &= ~(E1000_RCTL_SZ_4096);
-#if 0
- switch (adapter->rx_buffer_len) {
- case E1000_RXBUFFER_2048:
- default:
-#endif
rctl |= E1000_RCTL_SZ_2048;
rctl &= ~(E1000_RCTL_BSEX | E1000_RCTL_LPE);
-#if 0
- break;
- case E1000_RXBUFFER_4096:
- rctl |= E1000_RCTL_SZ_4096 | E1000_RCTL_BSEX | E1000_RCTL_LPE;
- break;
- case E1000_RXBUFFER_8192:
- rctl |= E1000_RCTL_SZ_8192 | E1000_RCTL_BSEX | E1000_RCTL_LPE;
- break;
- case E1000_RXBUFFER_16384:
- rctl |= E1000_RCTL_SZ_16384 | E1000_RCTL_BSEX | E1000_RCTL_LPE;
- break;
- }
-#endif
E1000_WRITE_REG(hw, RCTL, rctl);
}
@@ -2808,23 +4947,12 @@ static void
e1000_configure_rx(struct e1000_hw *hw)
{
unsigned long ptr;
- unsigned long rctl;
-#if 0
- unsigned long rxcsum;
-#endif
+ unsigned long rctl, ctrl_ext;
rx_tail = 0;
/* make sure receives are disabled while setting up the descriptors */
rctl = E1000_READ_REG(hw, RCTL);
E1000_WRITE_REG(hw, RCTL, rctl & ~E1000_RCTL_EN);
-#if 0
- /* set the Receive Delay Timer Register */
-
- E1000_WRITE_REG(hw, RDTR, adapter->rx_int_delay);
-#endif
if (hw->mac_type >= e1000_82540) {
-#if 0
- E1000_WRITE_REG(hw, RADV, adapter->rx_abs_int_delay);
-#endif
/* Set the interrupt throttling rate. Value is calculated
* as DEFAULT_ITR = 1/(MAX_INTS_PER_SEC * 256ns) */
#define MAX_INTS_PER_SEC 8000
@@ -2832,6 +4960,13 @@ e1000_configure_rx(struct e1000_hw *hw)
E1000_WRITE_REG(hw, ITR, DEFAULT_ITR);
}
+ if (hw->mac_type >= e1000_82571) {
+ ctrl_ext = E1000_READ_REG(hw, CTRL_EXT);
+ /* Reset delay timers after every interrupt */
+ ctrl_ext |= E1000_CTRL_EXT_INT_TIMER_CLR;
+ E1000_WRITE_REG(hw, CTRL_EXT, ctrl_ext);
+ E1000_WRITE_FLUSH(hw);
+ }
/* Setup the Base and Length of the Rx Descriptor Ring */
ptr = (u32) rx_pool;
if (ptr & 0xf)
@@ -2845,14 +4980,6 @@ e1000_configure_rx(struct e1000_hw *hw)
/* Setup the HW Rx Head and Tail Descriptor Pointers */
E1000_WRITE_REG(hw, RDH, 0);
E1000_WRITE_REG(hw, RDT, 0);
-#if 0
- /* Enable 82543 Receive Checksum Offload for TCP and UDP */
- if ((adapter->hw.mac_type >= e1000_82543) && (adapter->rx_csum == TRUE)) {
- rxcsum = E1000_READ_REG(hw, RXCSUM);
- rxcsum |= E1000_RXCSUM_TUOFL;
- E1000_WRITE_REG(hw, RXCSUM, rxcsum);
- }
-#endif
/* Enable Receives */
E1000_WRITE_REG(hw, RCTL, rctl);
@@ -2891,11 +5018,11 @@ e1000_transmit(struct eth_device *nic, volatile void *packet, int length)
tx_tail = (tx_tail + 1) % 8;
txp->buffer_addr = cpu_to_le64(virt_to_bus(packet));
- txp->lower.data = cpu_to_le32(E1000_TXD_CMD_RPS | E1000_TXD_CMD_EOP |
- E1000_TXD_CMD_IFCS | length);
+ txp->lower.data = cpu_to_le32(hw->txd_cmd | length);
txp->upper.data = 0;
E1000_WRITE_REG(hw, TDT, tx_tail);
+ E1000_WRITE_FLUSH(hw);
while (!(le32_to_cpu(txp->upper.data) & E1000_TXD_STAT_DD)) {
if (i++ > TOUT_LOOP) {
DEBUGOUT("e1000: tx timeout\n");
@@ -2972,6 +5099,37 @@ e1000_init(struct eth_device *nic, bd_t * bis)
return 1;
}
+/******************************************************************************
+ * Gets the current PCI bus type of hardware
+ *
+ * hw - Struct containing variables accessed by shared code
+ *****************************************************************************/
+void e1000_get_bus_type(struct e1000_hw *hw)
+{
+ uint32_t status;
+
+ switch (hw->mac_type) {
+ case e1000_82542_rev2_0:
+ case e1000_82542_rev2_1:
+ hw->bus_type = e1000_bus_type_pci;
+ break;
+ case e1000_82571:
+ case e1000_82572:
+ case e1000_82573:
+ case e1000_80003es2lan:
+ hw->bus_type = e1000_bus_type_pci_express;
+ break;
+ case e1000_ich8lan:
+ hw->bus_type = e1000_bus_type_pci_express;
+ break;
+ default:
+ status = E1000_READ_REG(hw, STATUS);
+ hw->bus_type = (status & E1000_STATUS_PCIX_MODE) ?
+ e1000_bus_type_pcix : e1000_bus_type_pci;
+ break;
+ }
+}
+
/**************************************************************************
PROBE - Look for an adapter, this routine's visible to the outside
You should omit the last argument struct pci_device * for a non-PCI NIC
@@ -3017,14 +5175,10 @@ e1000_initialize(bd_t * bis)
sprintf(nic->name, "e1000#%d", card_number);
/* Are these variables needed? */
-#if 0
- hw->fc = e1000_fc_none;
- hw->original_fc = e1000_fc_none;
-#else
hw->fc = e1000_fc_default;
hw->original_fc = e1000_fc_default;
-#endif
hw->autoneg_failed = 0;
+ hw->autoneg = 1;
hw->get_link_status = TRUE;
hw->hw_addr = (typeof(hw->hw_addr)) iobase;
hw->mac_type = e1000_undefined;
@@ -3035,7 +5189,16 @@ e1000_initialize(bd_t * bis)
free(nic);
return 0;
}
+ if (e1000_check_phy_reset_block(hw))
+ printf("phy reset block error \n");
+ e1000_reset_hw(hw);
#if !(defined(CONFIG_AP1000) || defined(CONFIG_MVBC_1G))
+ if (e1000_init_eeprom_params(hw)) {
+ printf("The EEPROM Checksum Is Not Valid\n");
+ free(hw);
+ free(nic);
+ return 0;
+ }
if (e1000_validate_eeprom_checksum(nic) < 0) {
printf("The EEPROM Checksum Is Not Valid\n");
free(hw);
@@ -3045,7 +5208,8 @@ e1000_initialize(bd_t * bis)
#endif
e1000_read_mac_addr(nic);
- E1000_WRITE_REG(hw, PBA, E1000_DEFAULT_PBA);
+ /* get the bus type information */
+ e1000_get_bus_type(hw);
printf("e1000: %02x:%02x:%02x:%02x:%02x:%02x\n",
nic->enetaddr[0], nic->enetaddr[1], nic->enetaddr[2],