diff options
Diffstat (limited to 'drivers/power/pmic/pmic_tps65090_ec.c')
| -rw-r--r-- | drivers/power/pmic/pmic_tps65090_ec.c | 218 |
1 files changed, 0 insertions, 218 deletions
diff --git a/drivers/power/pmic/pmic_tps65090_ec.c b/drivers/power/pmic/pmic_tps65090_ec.c deleted file mode 100644 index f79a878..0000000 --- a/drivers/power/pmic/pmic_tps65090_ec.c +++ /dev/null @@ -1,218 +0,0 @@ -/* - * Copyright (c) 2013 The Chromium OS Authors. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include <common.h> -#include <cros_ec.h> -#include <errno.h> -#include <power/tps65090_pmic.h> - -DECLARE_GLOBAL_DATA_PTR; - -#define TPS65090_ADDR 0x48 - -static struct tps65090 { - struct cros_ec_dev *dev; /* The CROS_EC device */ -} config; - -/* TPS65090 register addresses */ -enum { - REG_IRQ1 = 0, - REG_CG_CTRL0 = 4, - REG_CG_STATUS1 = 0xa, - REG_FET1_CTRL = 0x0f, - REG_FET2_CTRL, - REG_FET3_CTRL, - REG_FET4_CTRL, - REG_FET5_CTRL, - REG_FET6_CTRL, - REG_FET7_CTRL, - TPS65090_NUM_REGS, -}; - -enum { - IRQ1_VBATG = 1 << 3, - CG_CTRL0_ENC_MASK = 0x01, - - MAX_FET_NUM = 7, - MAX_CTRL_READ_TRIES = 5, - - /* TPS65090 FET_CTRL register values */ - FET_CTRL_TOFET = 1 << 7, /* Timeout, startup, overload */ - FET_CTRL_PGFET = 1 << 4, /* Power good for FET status */ - FET_CTRL_WAIT = 3 << 2, /* Overcurrent timeout max */ - FET_CTRL_ADENFET = 1 << 1, /* Enable output auto discharge */ - FET_CTRL_ENFET = 1 << 0, /* Enable FET */ -}; - -/** - * tps65090_read - read a byte from tps6090 - * - * @param reg The register address to read from. - * @param val We'll return value value read here. - * @return 0 if ok; error if EC returns failure. - */ -static int tps65090_read(u32 reg, u8 *val) -{ - return cros_ec_i2c_xfer_old(config.dev, TPS65090_ADDR, reg, 1, - val, 1, true); -} - -/** - * tps65090_write - write a byte to tps6090 - * - * @param reg The register address to write to. - * @param val The value to write. - * @return 0 if ok; error if EC returns failure. - */ -static int tps65090_write(u32 reg, u8 val) -{ - return cros_ec_i2c_xfer_old(config.dev, TPS65090_ADDR, reg, 1, - &val, 1, false); -} - -/** - * Checks for a valid FET number - * - * @param fet_id FET number to check - * @return 0 if ok, -EINVAL if FET value is out of range - */ -static int tps65090_check_fet(unsigned int fet_id) -{ - if (fet_id == 0 || fet_id > MAX_FET_NUM) { - debug("parameter fet_id is out of range, %u not in 1 ~ %u\n", - fet_id, MAX_FET_NUM); - return -EINVAL; - } - - return 0; -} - -/** - * Set the power state for a FET - * - * @param fet_id Fet number to set (1..MAX_FET_NUM) - * @param set 1 to power on FET, 0 to power off - * @return -EIO if we got a comms error, -EAGAIN if the FET failed to - * change state. If all is ok, returns 0. - */ -static int tps65090_fet_set(int fet_id, bool set) -{ - int retry; - u8 reg, value; - - value = FET_CTRL_ADENFET | FET_CTRL_WAIT; - if (set) - value |= FET_CTRL_ENFET; - - if (tps65090_write(REG_FET1_CTRL + fet_id - 1, value)) - return -EIO; - - /* Try reading until we get a result */ - for (retry = 0; retry < MAX_CTRL_READ_TRIES; retry++) { - if (tps65090_read(REG_FET1_CTRL + fet_id - 1, ®)) - return -EIO; - - /* Check that the fet went into the expected state */ - if (!!(reg & FET_CTRL_PGFET) == set) - return 0; - - /* If we got a timeout, there is no point in waiting longer */ - if (reg & FET_CTRL_TOFET) - break; - - mdelay(1); - } - - debug("FET %d: Power good should have set to %d but reg=%#02x\n", - fet_id, set, reg); - return -EAGAIN; -} - -int tps65090_fet_enable(unsigned int fet_id) -{ - ulong start; - int loops; - int ret; - - ret = tps65090_check_fet(fet_id); - if (ret) - return ret; - - start = get_timer(0); - for (loops = 0;; loops++) { - ret = tps65090_fet_set(fet_id, true); - if (!ret) - break; - - if (get_timer(start) > 100) - break; - - /* Turn it off and try again until we time out */ - tps65090_fet_set(fet_id, false); - } - - if (ret) { - debug("%s: FET%d failed to power on: time=%lums, loops=%d\n", - __func__, fet_id, get_timer(start), loops); - } else if (loops) { - debug("%s: FET%d powered on after %lums, loops=%d\n", - __func__, fet_id, get_timer(start), loops); - } - /* - * Unfortunately, there are some conditions where the power - * good bit will be 0, but the fet still comes up. One such - * case occurs with the lcd backlight. We'll just return 0 here - * and assume that the fet will eventually come up. - */ - if (ret == -EAGAIN) - ret = 0; - - return ret; -} - -int tps65090_fet_disable(unsigned int fet_id) -{ - int ret; - - ret = tps65090_check_fet(fet_id); - if (ret) - return ret; - - ret = tps65090_fet_set(fet_id, false); - - return ret; -} - -int tps65090_fet_is_enabled(unsigned int fet_id) -{ - u8 reg = 0; - int ret; - - ret = tps65090_check_fet(fet_id); - if (ret) - return ret; - ret = tps65090_read(REG_FET1_CTRL + fet_id - 1, ®); - if (ret) { - debug("fail to read FET%u_CTRL register over I2C", fet_id); - return -EIO; - } - - return reg & FET_CTRL_ENFET; -} - -int tps65090_init(void) -{ - puts("TPS65090 PMIC EC init\n"); - - config.dev = board_get_cros_ec_dev(); - if (!config.dev) { - debug("%s: no cros_ec device: cannot init tps65090\n", - __func__); - return -ENODEV; - } - - return 0; -} |