summaryrefslogtreecommitdiff
path: root/drivers/video/parade.c
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/video/parade.c')
-rw-r--r--drivers/video/parade.c220
1 files changed, 220 insertions, 0 deletions
diff --git a/drivers/video/parade.c b/drivers/video/parade.c
new file mode 100644
index 0000000..0f543f6
--- /dev/null
+++ b/drivers/video/parade.c
@@ -0,0 +1,220 @@
+/*
+ * Copyright (c) 2014 The Chromium OS Authors. All rights reserved.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+/*
+ * This file is a driver for Parade dP<->LVDS bridges. The original submission
+ * is for the ps8625 chip.
+ */
+#include <config.h>
+#include <common.h>
+#include <i2c.h>
+#include <fdtdec.h>
+
+/*
+ * Initialization of the chip is a process of writing certaing values into
+ * certain registers over i2c bus. The chip in fact responds to a range of
+ * addresses on the i2c bus, so for each written value three parameters are
+ * required: i2c address, register address and the actual value.
+ *
+ * The base address is derived from the device tree, only address offset is
+ * stored in the table below.
+ */
+/**
+ * struct reg_data() - data for a parade register write
+ *
+ * @addr_off offset from the i2c base address for parade
+ * @reg_addr register address to write
+ * @value value to be written
+ */
+struct reg_data {
+ uint8_t addr_off;
+ uint8_t reg;
+ uint8_t value;
+} _packed;
+
+#define END_OF_TABLE 0xff /* Ficticious offset */
+
+static const struct reg_data parade_values[] = {
+ {0x02, 0xa1, 0x01}, /* HPD low */
+ /*
+ * SW setting
+ * [1:0] SW output 1.2V voltage is lower to 96%
+ */
+ {0x04, 0x14, 0x01},
+ /*
+ * RCO SS setting
+ * [5:4] = b01 0.5%, b10 1%, b11 1.5%
+ */
+ {0x04, 0xe3, 0x20},
+ {0x04, 0xe2, 0x80}, /* [7] RCO SS enable */
+ /*
+ * RPHY Setting
+ * [3:2] CDR tune wait cycle before
+ * measure for fine tune b00: 1us,
+ * 01: 0.5us, 10:2us, 11:4us.
+ */
+ {0x04, 0x8a, 0x0c},
+ {0x04, 0x89, 0x08}, /* [3] RFD always on */
+ /*
+ * CTN lock in/out:
+ * 20000ppm/80000ppm. Lock out 2
+ * times.
+ */
+ {0x04, 0x71, 0x2d},
+ /*
+ * 2.7G CDR settings
+ * NOF=40LSB for HBR CDR setting
+ */
+ {0x04, 0x7d, 0x07},
+ {0x04, 0x7b, 0x00}, /* [1:0] Fmin=+4bands */
+ {0x04, 0x7a, 0xfd}, /* [7:5] DCO_FTRNG=+-40% */
+ /*
+ * 1.62G CDR settings
+ * [5:2]NOF=64LSB [1:0]DCO scale is 2/5
+ */
+ {0x04, 0xc0, 0x12},
+ {0x04, 0xc1, 0x92}, /* Gitune=-37% */
+ {0x04, 0xc2, 0x1c}, /* Fbstep=100% */
+ {0x04, 0x32, 0x80}, /* [7] LOS signal disable */
+ /*
+ * RPIO Setting
+ * [7:4] LVDS driver bias current :
+ * 75% (250mV swing)
+ */
+ {0x04, 0x00, 0xb0},
+ /*
+ * [7:6] Right-bar GPIO output strength is 8mA
+ */
+ {0x04, 0x15, 0x40},
+ /* EQ Training State Machine Setting */
+ {0x04, 0x54, 0x10}, /* RCO calibration start */
+ /* [4:0] MAX_LANE_COUNT set to one lane */
+ {0x01, 0x02, 0x81},
+ /* [4:0] LANE_COUNT_SET set to one lane */
+ {0x01, 0x21, 0x81},
+ {0x00, 0x52, 0x20},
+ {0x00, 0xf1, 0x03}, /* HPD CP toggle enable */
+ {0x00, 0x62, 0x41},
+ /* Counter number, add 1ms counter delay */
+ {0x00, 0xf6, 0x01},
+ /*
+ * [6]PWM function control by
+ * DPCD0040f[7], default is PWM
+ * block always works.
+ */
+ {0x00, 0x77, 0x06},
+ /*
+ * 04h Adjust VTotal tolerance to
+ * fix the 30Hz no display issue
+ */
+ {0x00, 0x4c, 0x04},
+ /* DPCD00400='h00, Parade OUI = 'h001cf8 */
+ {0x01, 0xc0, 0x00},
+ {0x01, 0xc1, 0x1c}, /* DPCD00401='h1c */
+ {0x01, 0xc2, 0xf8}, /* DPCD00402='hf8 */
+ /*
+ * DPCD403~408 = ASCII code
+ * D2SLV5='h4432534c5635
+ */
+ {0x01, 0xc3, 0x44},
+ {0x01, 0xc4, 0x32}, /* DPCD404 */
+ {0x01, 0xc5, 0x53}, /* DPCD405 */
+ {0x01, 0xc6, 0x4c}, /* DPCD406 */
+ {0x01, 0xc7, 0x56}, /* DPCD407 */
+ {0x01, 0xc8, 0x35}, /* DPCD408 */
+ /*
+ * DPCD40A, Initial Code major revision
+ * '01'
+ */
+ {0x01, 0xca, 0x01},
+ /* DPCD40B, Initial Code minor revision '05' */
+ {0x01, 0xcb, 0x05},
+ /* DPCD720, Select internal PWM */
+ {0x01, 0xa5, 0xa0},
+ /*
+ * FFh for 100% PWM of brightness, 0h for 0%
+ * brightness
+ */
+ {0x01, 0xa7, 0xff},
+ /*
+ * Set LVDS output as 6bit-VESA mapping,
+ * single LVDS channel
+ */
+ {0x01, 0xcc, 0x13},
+ /* Enable SSC set by register */
+ {0x02, 0xb1, 0x20},
+ /*
+ * Set SSC enabled and +/-1% central
+ * spreading
+ */
+ {0x04, 0x10, 0x16},
+ /* MPU Clock source: LC => RCO */
+ {0x04, 0x59, 0x60},
+ {0x04, 0x54, 0x14}, /* LC -> RCO */
+ {0x02, 0xa1, 0x91}, /* HPD high */
+ {END_OF_TABLE}
+};
+
+/**
+ * Write values table into the Parade eDP bridge
+ *
+ * @return 0 on success, non-0 on failure
+ */
+
+static int parade_write_regs(int base_addr, const struct reg_data *table)
+{
+ int ret = 0;
+
+ while (!ret && (table->addr_off != END_OF_TABLE)) {
+ ret = i2c_write(base_addr + table->addr_off,
+ table->reg, 1,
+ (uint8_t *)&table->value,
+ sizeof(table->value));
+ table++;
+ }
+ return ret;
+}
+
+int parade_init(const void *blob)
+{
+ int bus, old_bus;
+ int parent;
+ int node;
+ int addr;
+ int ret;
+
+ node = fdtdec_next_compatible(blob, 0, COMPAT_PARADE_PS8625);
+ if (node < 0)
+ return 0;
+
+ parent = fdt_parent_offset(blob, node);
+ if (parent < 0) {
+ debug("%s: Could not find parent i2c node\n", __func__);
+ return -1;
+ }
+ addr = fdtdec_get_int(blob, node, "reg", -1);
+ if (addr < 0) {
+ debug("%s: Could not find i2c address\n", __func__);
+ return -1;
+ }
+
+ bus = i2c_get_bus_num_fdt(parent);
+ old_bus = i2c_get_bus_num();
+
+ debug("%s: Using i2c bus %d\n", __func__, bus);
+
+ /*
+ * TODO(sjg@chromium.org): Hmmm we seem to need some sort of delay
+ * here.
+ */
+ mdelay(40);
+ i2c_set_bus_num(bus);
+ ret = parade_write_regs(addr, parade_values);
+
+ i2c_set_bus_num(old_bus);
+
+ return ret;
+}