summaryrefslogtreecommitdiff
path: root/include/configs/MPC8323ERDB.h
diff options
context:
space:
mode:
Diffstat (limited to 'include/configs/MPC8323ERDB.h')
-rw-r--r--include/configs/MPC8323ERDB.h376
1 files changed, 188 insertions, 188 deletions
diff --git a/include/configs/MPC8323ERDB.h b/include/configs/MPC8323ERDB.h
index 977142b..c6ac91a 100644
--- a/include/configs/MPC8323ERDB.h
+++ b/include/configs/MPC8323ERDB.h
@@ -32,7 +32,7 @@
/*
* Hardware Reset Configuration Word
*/
-#define CFG_HRCW_LOW (\
+#define CONFIG_SYS_HRCW_LOW (\
HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
HRCWL_DDR_TO_SCB_CLK_2X1 |\
HRCWL_VCO_1X2 |\
@@ -42,7 +42,7 @@
HRCWL_CE_PLL_DIV_1X1 |\
HRCWL_CE_TO_PLL_1X3)
-#define CFG_HRCW_HIGH (\
+#define CONFIG_SYS_HRCW_HIGH (\
HRCWH_PCI_HOST |\
HRCWH_PCI1_ARBITER_ENABLE |\
HRCWH_CORE_ENABLE |\
@@ -56,29 +56,29 @@
/*
* System IO Config
*/
-#define CFG_SICRL 0x00000000
+#define CONFIG_SYS_SICRL 0x00000000
#define CONFIG_BOARD_EARLY_INIT_F /* call board_pre_init */
/*
* IMMR new address
*/
-#define CFG_IMMR 0xE0000000
+#define CONFIG_SYS_IMMR 0xE0000000
/*
* System performance
*/
-#define CFG_ACR_PIPE_DEP 3 /* Arbiter pipeline depth (0-3) */
-#define CFG_ACR_RPTCNT 3 /* Arbiter repeat count (0-7) */
-#define CFG_SPCR_OPT 1 /* (0-1) Optimize transactions between CSB and the SEC and QUICC Engine block */
+#define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth (0-3) */
+#define CONFIG_SYS_ACR_RPTCNT 3 /* Arbiter repeat count (0-7) */
+#define CONFIG_SYS_SPCR_OPT 1 /* (0-1) Optimize transactions between CSB and the SEC and QUICC Engine block */
/*
* DDR Setup
*/
-#define CFG_DDR_BASE 0x00000000 /* DDR is system memory */
-#define CFG_SDRAM_BASE CFG_DDR_BASE
-#define CFG_DDR_SDRAM_BASE CFG_DDR_BASE
-#define CFG_DDRCDR 0x73000002 /* DDR II voltage is 1.8V */
+#define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory */
+#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE
+#define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE
+#define CONFIG_SYS_DDRCDR 0x73000002 /* DDR II voltage is 1.8V */
#undef CONFIG_SPD_EEPROM
#if defined(CONFIG_SPD_EEPROM)
@@ -88,12 +88,12 @@
#else
/* Manually set up DDR parameters
*/
-#define CFG_DDR_SIZE 64 /* MB */
-#define CFG_DDR_CS0_CONFIG ( CSCONFIG_EN \
+#define CONFIG_SYS_DDR_SIZE 64 /* MB */
+#define CONFIG_SYS_DDR_CS0_CONFIG ( CSCONFIG_EN \
| CSCONFIG_ODT_WR_ACS \
| CSCONFIG_ROW_BIT_13 | CSCONFIG_COL_BIT_9 )
/* 0x80010101 */
-#define CFG_DDR_TIMING_0 ( ( 0 << TIMING_CFG0_RWT_SHIFT ) \
+#define CONFIG_SYS_DDR_TIMING_0 ( ( 0 << TIMING_CFG0_RWT_SHIFT ) \
| ( 0 << TIMING_CFG0_WRT_SHIFT ) \
| ( 0 << TIMING_CFG0_RRT_SHIFT ) \
| ( 0 << TIMING_CFG0_WWT_SHIFT ) \
@@ -102,7 +102,7 @@
| ( 8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT ) \
| ( 2 << TIMING_CFG0_MRS_CYC_SHIFT ) )
/* 0x00220802 */
-#define CFG_DDR_TIMING_1 ( ( 2 << TIMING_CFG1_PRETOACT_SHIFT ) \
+#define CONFIG_SYS_DDR_TIMING_1 ( ( 2 << TIMING_CFG1_PRETOACT_SHIFT ) \
| ( 6 << TIMING_CFG1_ACTTOPRE_SHIFT ) \
| ( 2 << TIMING_CFG1_ACTTORW_SHIFT ) \
| ( 5 << TIMING_CFG1_CASLAT_SHIFT ) \
@@ -111,7 +111,7 @@
| ( 2 << TIMING_CFG1_ACTTOACT_SHIFT ) \
| ( 2 << TIMING_CFG1_WRTORD_SHIFT ) )
/* 0x26253222 */
-#define CFG_DDR_TIMING_2 ( ( 1 << TIMING_CFG2_ADD_LAT_SHIFT ) \
+#define CONFIG_SYS_DDR_TIMING_2 ( ( 1 << TIMING_CFG2_ADD_LAT_SHIFT ) \
| (31 << TIMING_CFG2_CPO_SHIFT ) \
| ( 2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT ) \
| ( 2 << TIMING_CFG2_RD_TO_PRE_SHIFT ) \
@@ -119,98 +119,99 @@
| ( 3 << TIMING_CFG2_CKE_PLS_SHIFT ) \
| ( 7 << TIMING_CFG2_FOUR_ACT_SHIFT) )
/* 0x1f9048c7 */
-#define CFG_DDR_TIMING_3 0x00000000
-#define CFG_DDR_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
+#define CONFIG_SYS_DDR_TIMING_3 0x00000000
+#define CONFIG_SYS_DDR_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
/* 0x02000000 */
-#define CFG_DDR_MODE ( ( 0x4448 << SDRAM_MODE_ESD_SHIFT ) \
+#define CONFIG_SYS_DDR_MODE ( ( 0x4448 << SDRAM_MODE_ESD_SHIFT ) \
| ( 0x0232 << SDRAM_MODE_SD_SHIFT ) )
/* 0x44480232 */
-#define CFG_DDR_MODE2 0x8000c000
-#define CFG_DDR_INTERVAL ( ( 800 << SDRAM_INTERVAL_REFINT_SHIFT ) \
+#define CONFIG_SYS_DDR_MODE2 0x8000c000
+#define CONFIG_SYS_DDR_INTERVAL ( ( 800 << SDRAM_INTERVAL_REFINT_SHIFT ) \
| ( 100 << SDRAM_INTERVAL_BSTOPRE_SHIFT ) )
/* 0x03200064 */
-#define CFG_DDR_CS0_BNDS 0x00000003
-#define CFG_DDR_SDRAM_CFG ( SDRAM_CFG_SREN \
+#define CONFIG_SYS_DDR_CS0_BNDS 0x00000003
+#define CONFIG_SYS_DDR_SDRAM_CFG ( SDRAM_CFG_SREN \
| SDRAM_CFG_SDRAM_TYPE_DDR2 \
| SDRAM_CFG_32_BE )
/* 0x43080000 */
-#define CFG_DDR_SDRAM_CFG2 0x00401000
+#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000
#endif
/*
* Memory test
*/
-#undef CFG_DRAM_TEST /* memory test, takes time */
-#define CFG_MEMTEST_START 0x00030000 /* memtest region */
-#define CFG_MEMTEST_END 0x03f00000
+#undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */
+#define CONFIG_SYS_MEMTEST_START 0x00030000 /* memtest region */
+#define CONFIG_SYS_MEMTEST_END 0x03f00000
/*
* The reserved memory
*/
-#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */
+#define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */
-#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
-#define CFG_RAMBOOT
+#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
+#define CONFIG_SYS_RAMBOOT
#else
-#undef CFG_RAMBOOT
+#undef CONFIG_SYS_RAMBOOT
#endif
-/* CFG_MONITOR_LEN must be a multiple of CONFIG_ENV_SECT_SIZE */
-#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
-#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
+/* CONFIG_SYS_MONITOR_LEN must be a multiple of CONFIG_ENV_SECT_SIZE */
+#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
+#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
/*
* Initial RAM Base Address Setup
*/
-#define CFG_INIT_RAM_LOCK 1
-#define CFG_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */
-#define CFG_INIT_RAM_END 0x1000 /* End of used area in RAM */
-#define CFG_GBL_DATA_SIZE 0x100 /* num bytes initial data */
-#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_RAM_LOCK 1
+#define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */
+#define CONFIG_SYS_INIT_RAM_END 0x1000 /* End of used area in RAM */
+#define CONFIG_SYS_GBL_DATA_SIZE 0x100 /* num bytes initial data */
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
/*
* Local Bus Configuration & Clock Setup
*/
-#define CFG_LCRR (LCRR_DBYP | LCRR_CLKDIV_2)
-#define CFG_LBC_LBCR 0x00000000
+#define CONFIG_SYS_LCRR (LCRR_DBYP | LCRR_CLKDIV_2)
+#define CONFIG_SYS_LBC_LBCR 0x00000000
/*
* FLASH on the Local Bus
*/
-#define CFG_FLASH_CFI /* use the Common Flash Interface */
+#define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */
#define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */
-#define CFG_FLASH_BASE 0xFE000000 /* FLASH base address */
-#define CFG_FLASH_SIZE 16 /* FLASH size is 16M */
+#define CONFIG_SYS_FLASH_BASE 0xFE000000 /* FLASH base address */
+#define CONFIG_SYS_FLASH_SIZE 16 /* FLASH size is 16M */
+#define CONFIG_SYS_FLASH_PROTECTION 1 /* Use h/w Flash protection. */
-#define CFG_LBLAWBAR0_PRELIM CFG_FLASH_BASE /* Window base at flash base */
-#define CFG_LBLAWAR0_PRELIM 0x80000018 /* 32MB window size */
+#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE /* Window base at flash base */
+#define CONFIG_SYS_LBLAWAR0_PRELIM 0x80000018 /* 32MB window size */
-#define CFG_BR0_PRELIM (CFG_FLASH_BASE | /* Flash Base address */ \
+#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | /* Flash Base address */ \
(2 << BR_PS_SHIFT) | /* 16 bit port size */ \
BR_V) /* valid */
-#define CFG_OR0_PRELIM 0xfe006ff7 /* 16MB Flash size */
+#define CONFIG_SYS_OR0_PRELIM 0xfe006ff7 /* 16MB Flash size */
-#define CFG_MAX_FLASH_BANKS 1 /* number of banks */
-#define CFG_MAX_FLASH_SECT 128 /* sectors per device */
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 128 /* sectors per device */
-#undef CFG_FLASH_CHECKSUM
+#undef CONFIG_SYS_FLASH_CHECKSUM
/*
* SDRAM on the Local Bus
*/
-#undef CFG_LB_SDRAM /* The board has not SRDAM on local bus */
+#undef CONFIG_SYS_LB_SDRAM /* The board has not SRDAM on local bus */
-#ifdef CFG_LB_SDRAM
-#define CFG_LBC_SDRAM_BASE 0xF0000000 /* SDRAM base address */
-#define CFG_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */
+#ifdef CONFIG_SYS_LB_SDRAM
+#define CONFIG_SYS_LBC_SDRAM_BASE 0xF0000000 /* SDRAM base address */
+#define CONFIG_SYS_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */
-#define CFG_LBLAWBAR2_PRELIM CFG_LBC_SDRAM_BASE
-#define CFG_LBLAWAR2_PRELIM 0x80000019 /* 64MB */
+#define CONFIG_SYS_LBLAWBAR2_PRELIM CONFIG_SYS_LBC_SDRAM_BASE
+#define CONFIG_SYS_LBLAWAR2_PRELIM 0x80000019 /* 64MB */
/*local bus BR2, OR2 definition for SDRAM if soldered on the EPB board */
/*
* Base Register 2 and Option Register 2 configure SDRAM.
- * The SDRAM base address, CFG_LBC_SDRAM_BASE, is 0xf0000000.
+ * The SDRAM base address, CONFIG_SYS_LBC_SDRAM_BASE, is 0xf0000000.
*
* For BR2, need:
* Base address of 0xf0000000 = BR[0:16] = 1111 0000 0000 0000 0
@@ -222,14 +223,14 @@
* 0 4 8 12 16 20 24 28
* 1111 0000 0000 0000 0001 1000 0110 0001 = f0001861
*
- * CFG_LBC_SDRAM_BASE should be masked and OR'ed into
+ * CONFIG_SYS_LBC_SDRAM_BASE should be masked and OR'ed into
* the top 17 bits of BR2.
*/
-#define CFG_BR2_PRELIM 0xf0001861 /*Port size=32bit, MSEL=SDRAM */
+#define CONFIG_SYS_BR2_PRELIM 0xf0001861 /*Port size=32bit, MSEL=SDRAM */
/*
- * The SDRAM size in MB, CFG_LBC_SDRAM_SIZE, is 64.
+ * The SDRAM size in MB, CONFIG_SYS_LBC_SDRAM_SIZE, is 64.
*
* For OR2, need:
* 64MB mask for AM, OR2[0:7] = 1111 1100
@@ -242,68 +243,68 @@
* 1111 1100 0000 0000 0110 1001 0000 0001 = fc006901
*/
-#define CFG_OR2_PRELIM 0xfc006901
+#define CONFIG_SYS_OR2_PRELIM 0xfc006901
-#define CFG_LBC_LSRT 0x32000000 /* LB sdram refresh timer, about 6us */
-#define CFG_LBC_MRTPR 0x20000000 /* LB refresh timer prescal, 266MHz/32 */
+#define CONFIG_SYS_LBC_LSRT 0x32000000 /* LB sdram refresh timer, about 6us */
+#define CONFIG_SYS_LBC_MRTPR 0x20000000 /* LB refresh timer prescal, 266MHz/32 */
/*
* LSDMR masks
*/
-#define CFG_LBC_LSDMR_OP_NORMAL (0 << (31 - 4))
-#define CFG_LBC_LSDMR_OP_ARFRSH (1 << (31 - 4))
-#define CFG_LBC_LSDMR_OP_SRFRSH (2 << (31 - 4))
-#define CFG_LBC_LSDMR_OP_MRW (3 << (31 - 4))
-#define CFG_LBC_LSDMR_OP_PRECH (4 << (31 - 4))
-#define CFG_LBC_LSDMR_OP_PCHALL (5 << (31 - 4))
-#define CFG_LBC_LSDMR_OP_ACTBNK (6 << (31 - 4))
-#define CFG_LBC_LSDMR_OP_RWINV (7 << (31 - 4))
+#define CONFIG_SYS_LBC_LSDMR_OP_NORMAL (0 << (31 - 4))
+#define CONFIG_SYS_LBC_LSDMR_OP_ARFRSH (1 << (31 - 4))
+#define CONFIG_SYS_LBC_LSDMR_OP_SRFRSH (2 << (31 - 4))
+#define CONFIG_SYS_LBC_LSDMR_OP_MRW (3 << (31 - 4))
+#define CONFIG_SYS_LBC_LSDMR_OP_PRECH (4 << (31 - 4))
+#define CONFIG_SYS_LBC_LSDMR_OP_PCHALL (5 << (31 - 4))
+#define CONFIG_SYS_LBC_LSDMR_OP_ACTBNK (6 << (31 - 4))
+#define CONFIG_SYS_LBC_LSDMR_OP_RWINV (7 << (31 - 4))
-#define CFG_LBC_LSDMR_COMMON 0x0063b723
+#define CONFIG_SYS_LBC_LSDMR_COMMON 0x0063b723
/*
* SDRAM Controller configuration sequence.
*/
-#define CFG_LBC_LSDMR_1 ( CFG_LBC_LSDMR_COMMON \
- | CFG_LBC_LSDMR_OP_PCHALL)
-#define CFG_LBC_LSDMR_2 ( CFG_LBC_LSDMR_COMMON \
- | CFG_LBC_LSDMR_OP_ARFRSH)
-#define CFG_LBC_LSDMR_3 ( CFG_LBC_LSDMR_COMMON \
- | CFG_LBC_LSDMR_OP_ARFRSH)
-#define CFG_LBC_LSDMR_4 ( CFG_LBC_LSDMR_COMMON \
- | CFG_LBC_LSDMR_OP_MRW)
-#define CFG_LBC_LSDMR_5 ( CFG_LBC_LSDMR_COMMON \
- | CFG_LBC_LSDMR_OP_NORMAL)
+#define CONFIG_SYS_LBC_LSDMR_1 ( CONFIG_SYS_LBC_LSDMR_COMMON \
+ | CONFIG_SYS_LBC_LSDMR_OP_PCHALL)
+#define CONFIG_SYS_LBC_LSDMR_2 ( CONFIG_SYS_LBC_LSDMR_COMMON \
+ | CONFIG_SYS_LBC_LSDMR_OP_ARFRSH)
+#define CONFIG_SYS_LBC_LSDMR_3 ( CONFIG_SYS_LBC_LSDMR_COMMON \
+ | CONFIG_SYS_LBC_LSDMR_OP_ARFRSH)
+#define CONFIG_SYS_LBC_LSDMR_4 ( CONFIG_SYS_LBC_LSDMR_COMMON \
+ | CONFIG_SYS_LBC_LSDMR_OP_MRW)
+#define CONFIG_SYS_LBC_LSDMR_5 ( CONFIG_SYS_LBC_LSDMR_COMMON \
+ | CONFIG_SYS_LBC_LSDMR_OP_NORMAL)
#endif
/*
* Windows to access PIB via local bus
*/
-#define CFG_LBLAWBAR3_PRELIM 0xf8008000 /* windows base 0xf8008000 */
-#define CFG_LBLAWAR3_PRELIM 0x8000000f /* windows size 64KB */
+#define CONFIG_SYS_LBLAWBAR3_PRELIM 0xf8008000 /* windows base 0xf8008000 */
+#define CONFIG_SYS_LBLAWAR3_PRELIM 0x8000000f /* windows size 64KB */
/*
* Serial Port
*/
#define CONFIG_CONS_INDEX 1
#undef CONFIG_SERIAL_SOFTWARE_FIFO
-#define CFG_NS16550
-#define CFG_NS16550_SERIAL
-#define CFG_NS16550_REG_SIZE 1
-#define CFG_NS16550_CLK get_bus_freq(0)
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE 1
+#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
-#define CFG_BAUDRATE_TABLE \
+#define CONFIG_SYS_BAUDRATE_TABLE \
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
-#define CFG_NS16550_COM1 (CFG_IMMR+0x4500)
-#define CFG_NS16550_COM2 (CFG_IMMR+0x4600)
+#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500)
+#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600)
#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
/* Use the HUSH parser */
-#define CFG_HUSH_PARSER
-#ifdef CFG_HUSH_PARSER
-#define CFG_PROMPT_HUSH_PS2 "> "
+#define CONFIG_SYS_HUSH_PARSER
+#ifdef CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
#endif
/* pass open firmware flat tree */
@@ -315,33 +316,32 @@
#define CONFIG_HARD_I2C /* I2C with hardware support */
#undef CONFIG_SOFT_I2C /* I2C bit-banged */
#define CONFIG_FSL_I2C
-#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CFG_I2C_SLAVE 0x7F
-#define CFG_I2C_NOPROBES {0x51} /* Don't probe these addrs */
-#define CFG_I2C_OFFSET 0x3000
+#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
+#define CONFIG_SYS_I2C_SLAVE 0x7F
+#define CONFIG_SYS_I2C_NOPROBES {0x51} /* Don't probe these addrs */
+#define CONFIG_SYS_I2C_OFFSET 0x3000
/*
* Config on-board EEPROM
*/
-#define CFG_I2C_EEPROM_ADDR 0x50
-#define CFG_I2C_EEPROM_ADDR_LEN 2
-#define CFG_EEPROM_PAGE_WRITE_BITS 6
-#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10
-#define CFG_EEPROM_PAGE_WRITE_ENABLE
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10
/*
* General PCI
* Addresses are mapped 1-1.
*/
-#define CFG_PCI1_MEM_BASE 0x80000000
-#define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE
-#define CFG_PCI1_MEM_SIZE 0x10000000 /* 256M */
-#define CFG_PCI1_MMIO_BASE 0x90000000
-#define CFG_PCI1_MMIO_PHYS CFG_PCI1_MMIO_BASE
-#define CFG_PCI1_MMIO_SIZE 0x10000000 /* 256M */
-#define CFG_PCI1_IO_BASE 0xd0000000
-#define CFG_PCI1_IO_PHYS CFG_PCI1_IO_BASE
-#define CFG_PCI1_IO_SIZE 0x04000000 /* 64M */
+#define CONFIG_SYS_PCI1_MEM_BASE 0x80000000
+#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE
+#define CONFIG_SYS_PCI1_MEM_SIZE 0x10000000 /* 256M */
+#define CONFIG_SYS_PCI1_MMIO_BASE 0x90000000
+#define CONFIG_SYS_PCI1_MMIO_PHYS CONFIG_SYS_PCI1_MMIO_BASE
+#define CONFIG_SYS_PCI1_MMIO_SIZE 0x10000000 /* 256M */
+#define CONFIG_SYS_PCI1_IO_BASE 0xd0000000
+#define CONFIG_SYS_PCI1_IO_PHYS CONFIG_SYS_PCI1_IO_BASE
+#define CONFIG_SYS_PCI1_IO_SIZE 0x04000000 /* 64M */
#ifdef CONFIG_PCI
#define CONFIG_PCI_SKIP_HOST_BRIDGE
@@ -350,7 +350,7 @@
#undef CONFIG_EEPRO100
#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
-#define CFG_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */
+#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */
#endif /* CONFIG_PCI */
@@ -368,42 +368,42 @@
#define CONFIG_UEC_ETH1 /* ETH3 */
#ifdef CONFIG_UEC_ETH1
-#define CFG_UEC1_UCC_NUM 2 /* UCC3 */
-#define CFG_UEC1_RX_CLK QE_CLK9
-#define CFG_UEC1_TX_CLK QE_CLK10
-#define CFG_UEC1_ETH_TYPE FAST_ETH
-#define CFG_UEC1_PHY_ADDR 4
-#define CFG_UEC1_INTERFACE_MODE ENET_100_MII
+#define CONFIG_SYS_UEC1_UCC_NUM 2 /* UCC3 */
+#define CONFIG_SYS_UEC1_RX_CLK QE_CLK9
+#define CONFIG_SYS_UEC1_TX_CLK QE_CLK10
+#define CONFIG_SYS_UEC1_ETH_TYPE FAST_ETH
+#define CONFIG_SYS_UEC1_PHY_ADDR 4
+#define CONFIG_SYS_UEC1_INTERFACE_MODE ENET_100_MII
#endif
#define CONFIG_UEC_ETH2 /* ETH4 */
#ifdef CONFIG_UEC_ETH2
-#define CFG_UEC2_UCC_NUM 1 /* UCC2 */
-#define CFG_UEC2_RX_CLK QE_CLK16
-#define CFG_UEC2_TX_CLK QE_CLK3
-#define CFG_UEC2_ETH_TYPE FAST_ETH
-#define CFG_UEC2_PHY_ADDR 0
-#define CFG_UEC2_INTERFACE_MODE ENET_100_MII
+#define CONFIG_SYS_UEC2_UCC_NUM 1 /* UCC2 */
+#define CONFIG_SYS_UEC2_RX_CLK QE_CLK16
+#define CONFIG_SYS_UEC2_TX_CLK QE_CLK3
+#define CONFIG_SYS_UEC2_ETH_TYPE FAST_ETH
+#define CONFIG_SYS_UEC2_PHY_ADDR 0
+#define CONFIG_SYS_UEC2_INTERFACE_MODE ENET_100_MII
#endif
/*
* Environment
*/
-#ifndef CFG_RAMBOOT
+#ifndef CONFIG_SYS_RAMBOOT
#define CONFIG_ENV_IS_IN_FLASH 1
- #define CONFIG_ENV_ADDR (CFG_MONITOR_BASE + CFG_MONITOR_LEN)
+ #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
#define CONFIG_ENV_SECT_SIZE 0x20000
#define CONFIG_ENV_SIZE 0x2000
#else
- #define CFG_NO_FLASH 1 /* Flash is not usable now */
+ #define CONFIG_SYS_NO_FLASH 1 /* Flash is not usable now */
#define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
- #define CONFIG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000)
+ #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
#define CONFIG_ENV_SIZE 0x2000
#endif
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
/*
* BOOTP options
@@ -426,7 +426,7 @@
#if defined(CONFIG_PCI)
#define CONFIG_CMD_PCI
#endif
-#if defined(CFG_RAMBOOT)
+#if defined(CONFIG_SYS_RAMBOOT)
#undef CONFIG_CMD_ENV
#undef CONFIG_CMD_LOADS
#endif
@@ -436,34 +436,34 @@
/*
* Miscellaneous configurable options
*/
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_LOAD_ADDR 0x2000000 /* default load address */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
+#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
#if (CONFIG_CMD_KGDB)
- #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+ #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
- #define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+ #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_HZ 1000 /* decrementer freq: 1ms ticks */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
+#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/*
* Core HID Setup
*/
-#define CFG_HID0_INIT 0x000000000
-#define CFG_HID0_FINAL HID0_ENABLE_MACHINE_CHECK
-#define CFG_HID2 HID2_HBE
+#define CONFIG_SYS_HID0_INIT 0x000000000
+#define CONFIG_SYS_HID0_FINAL HID0_ENABLE_MACHINE_CHECK
+#define CONFIG_SYS_HID2 HID2_HBE
/*
* MMU Setup
@@ -471,64 +471,64 @@
#define CONFIG_HIGH_BATS 1 /* High BATs supported */
/* DDR: cache cacheable */
-#define CFG_IBAT0L (CFG_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
-#define CFG_IBAT0U (CFG_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
-#define CFG_DBAT0L CFG_IBAT0L
-#define CFG_DBAT0U CFG_IBAT0U
+#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L
+#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U
/* IMMRBAR & PCI IO: cache-inhibit and guarded */
-#define CFG_IBAT1L (CFG_IMMR | BATL_PP_10 | \
+#define CONFIG_SYS_IBAT1L (CONFIG_SYS_IMMR | BATL_PP_10 | \
BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CFG_IBAT1U (CFG_IMMR | BATU_BL_4M | BATU_VS | BATU_VP)
-#define CFG_DBAT1L CFG_IBAT1L
-#define CFG_DBAT1U CFG_IBAT1U
+#define CONFIG_SYS_IBAT1U (CONFIG_SYS_IMMR | BATU_BL_4M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L
+#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U
/* FLASH: icache cacheable, but dcache-inhibit and guarded */
-#define CFG_IBAT2L (CFG_FLASH_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
-#define CFG_IBAT2U (CFG_FLASH_BASE | BATU_BL_32M | BATU_VS | BATU_VP)
-#define CFG_DBAT2L (CFG_FLASH_BASE | BATL_PP_10 | \
+#define CONFIG_SYS_IBAT2L (CONFIG_SYS_FLASH_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT2U (CONFIG_SYS_FLASH_BASE | BATU_BL_32M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_DBAT2L (CONFIG_SYS_FLASH_BASE | BATL_PP_10 | \
BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CFG_DBAT2U CFG_IBAT2U
+#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U
-#define CFG_IBAT3L (0)
-#define CFG_IBAT3U (0)
-#define CFG_DBAT3L CFG_IBAT3L
-#define CFG_DBAT3U CFG_IBAT3U
+#define CONFIG_SYS_IBAT3L (0)
+#define CONFIG_SYS_IBAT3U (0)
+#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L
+#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U
/* Stack in dcache: cacheable, no memory coherence */
-#define CFG_IBAT4L (CFG_INIT_RAM_ADDR | BATL_PP_10)
-#define CFG_IBAT4U (CFG_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
-#define CFG_DBAT4L CFG_IBAT4L
-#define CFG_DBAT4U CFG_IBAT4U
+#define CONFIG_SYS_IBAT4L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_10)
+#define CONFIG_SYS_IBAT4U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
+#define CONFIG_SYS_DBAT4L CONFIG_SYS_IBAT4L
+#define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U
#ifdef CONFIG_PCI
/* PCI MEM space: cacheable */
-#define CFG_IBAT5L (CFG_PCI1_MEM_PHYS | BATL_PP_10 | BATL_MEMCOHERENCE)
-#define CFG_IBAT5U (CFG_PCI1_MEM_PHYS | BATU_BL_256M | BATU_VS | BATU_VP)
-#define CFG_DBAT5L CFG_IBAT5L
-#define CFG_DBAT5U CFG_IBAT5U
+#define CONFIG_SYS_IBAT5L (CONFIG_SYS_PCI1_MEM_PHYS | BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT5U (CONFIG_SYS_PCI1_MEM_PHYS | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_DBAT5L CONFIG_SYS_IBAT5L
+#define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U
/* PCI MMIO space: cache-inhibit and guarded */
-#define CFG_IBAT6L (CFG_PCI1_MMIO_PHYS | BATL_PP_10 | \
+#define CONFIG_SYS_IBAT6L (CONFIG_SYS_PCI1_MMIO_PHYS | BATL_PP_10 | \
BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CFG_IBAT6U (CFG_PCI1_MMIO_PHYS | BATU_BL_256M | BATU_VS | BATU_VP)
-#define CFG_DBAT6L CFG_IBAT6L
-#define CFG_DBAT6U CFG_IBAT6U
+#define CONFIG_SYS_IBAT6U (CONFIG_SYS_PCI1_MMIO_PHYS | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L
+#define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U
#else
-#define CFG_IBAT5L (0)
-#define CFG_IBAT5U (0)
-#define CFG_IBAT6L (0)
-#define CFG_IBAT6U (0)
-#define CFG_DBAT5L CFG_IBAT5L
-#define CFG_DBAT5U CFG_IBAT5U
-#define CFG_DBAT6L CFG_IBAT6L
-#define CFG_DBAT6U CFG_IBAT6U
+#define CONFIG_SYS_IBAT5L (0)
+#define CONFIG_SYS_IBAT5U (0)
+#define CONFIG_SYS_IBAT6L (0)
+#define CONFIG_SYS_IBAT6U (0)
+#define CONFIG_SYS_DBAT5L CONFIG_SYS_IBAT5L
+#define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U
+#define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L
+#define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U
#endif
/* Nothing in BAT7 */
-#define CFG_IBAT7L (0)
-#define CFG_IBAT7U (0)
-#define CFG_DBAT7L CFG_IBAT7L
-#define CFG_DBAT7U CFG_IBAT7U
+#define CONFIG_SYS_IBAT7L (0)
+#define CONFIG_SYS_IBAT7U (0)
+#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L
+#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U
/*
* Internal Definitions
@@ -553,8 +553,8 @@
#define CONFIG_HAS_ETH1 /* add support for "eth1addr" */
#define CONFIG_ETH1ADDR 00:04:9f:ef:03:02
-/* use mac_read_from_eeprom() to read ethaddr from I2C EEPROM (see CFG_I2C_EEPROM) */
-#define CFG_I2C_MAC_OFFSET 0x7f00 /* MAC address offset in I2C EEPROM */
+/* use mac_read_from_eeprom() to read ethaddr from I2C EEPROM (see CONFIG_SYS_I2C_EEPROM) */
+#define CONFIG_SYS_I2C_MAC_OFFSET 0x7f00 /* MAC address offset in I2C EEPROM */
#define CONFIG_IPADDR 10.0.0.2
#define CONFIG_SERVERIP 10.0.0.1
@@ -570,7 +570,7 @@
#define CONFIG_FDTFILE mpc832x_rdb.dtb
#define CONFIG_LOADADDR 500000 /* default location for tftp and bootm */
-#define CONFIG_BOOTDELAY -1 /* -1 disables auto-boot */
+#define CONFIG_BOOTDELAY 6 /* -1 disables auto-boot */
#define CONFIG_BAUDRATE 115200
#define XMK_STR(x) #x