summaryrefslogtreecommitdiff
path: root/include/configs/MPC8610HPCD.h
diff options
context:
space:
mode:
Diffstat (limited to 'include/configs/MPC8610HPCD.h')
-rw-r--r--include/configs/MPC8610HPCD.h344
1 files changed, 172 insertions, 172 deletions
diff --git a/include/configs/MPC8610HPCD.h b/include/configs/MPC8610HPCD.h
index 4eee21c..678e1e1 100644
--- a/include/configs/MPC8610HPCD.h
+++ b/include/configs/MPC8610HPCD.h
@@ -31,10 +31,10 @@
#endif
#ifdef RUN_DIAG
-#define CFG_DIAG_ADDR 0xff800000
+#define CONFIG_SYS_DIAG_ADDR 0xff800000
#endif
-#define CFG_RESET_ADDRESS 0xfff00100
+#define CONFIG_SYS_RESET_ADDRESS 0xfff00100
#define CONFIG_PCI 1 /* Enable PCI/PCIE*/
#define CONFIG_PCI1 1 /* PCI controler 1 */
@@ -52,7 +52,7 @@
/*
* L2CR setup -- make sure this is right for your board!
*/
-#define CFG_L2
+#define CONFIG_SYS_L2
#define L2_INIT 0
#define L2_ENABLE (L2CR_L2E |0x00100000 )
@@ -63,22 +63,22 @@
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */
#define CONFIG_MISC_INIT_R 1
-#define CFG_MEMTEST_START 0x00200000 /* memtest region */
-#define CFG_MEMTEST_END 0x00400000
+#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest region */
+#define CONFIG_SYS_MEMTEST_END 0x00400000
/*
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*/
-#define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
-#define CFG_CCSRBAR 0xe0000000 /* relocated CCSRBAR */
-#define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */
+#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
+#define CONFIG_SYS_CCSRBAR 0xe0000000 /* relocated CCSRBAR */
+#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */
-#define CFG_PCI1_ADDR (CFG_CCSRBAR+0x8000)
-#define CFG_PCIE1_ADDR (CFG_CCSRBAR+0xa000)
-#define CFG_PCIE2_ADDR (CFG_CCSRBAR+0x9000)
+#define CONFIG_SYS_PCI1_ADDR (CONFIG_SYS_CCSRBAR+0x8000)
+#define CONFIG_SYS_PCIE1_ADDR (CONFIG_SYS_CCSRBAR+0xa000)
+#define CONFIG_SYS_PCIE2_ADDR (CONFIG_SYS_CCSRBAR+0x9000)
-#define CFG_DIU_ADDR (CFG_CCSRBAR+0x2c000)
+#define CONFIG_SYS_DIU_ADDR (CONFIG_SYS_CCSRBAR+0x2c000)
/* DDR Setup */
#define CONFIG_FSL_DDR2
@@ -89,8 +89,8 @@
#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */
#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
-#define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/
-#define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE
+#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/
+#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
#define CONFIG_VERY_BIG_RAM
#define MPC86xx_DDR_SDRAM_CLK_CNTL
@@ -102,64 +102,64 @@
#define SPD_EEPROM_ADDRESS1 0x51 /* CTLR 0 DIMM 0 */
/* These are used when DDR doesn't use SPD. */
-#define CFG_SDRAM_SIZE 256 /* DDR is 256MB */
+#define CONFIG_SYS_SDRAM_SIZE 256 /* DDR is 256MB */
#if 0 /* TODO */
-#define CFG_DDR_CS0_BNDS 0x0000000F
-#define CFG_DDR_CS0_CONFIG 0x80010202 /* Enable, no interleaving */
-#define CFG_DDR_TIMING_3 0x00000000
-#define CFG_DDR_TIMING_0 0x00260802
-#define CFG_DDR_TIMING_1 0x3935d322
-#define CFG_DDR_TIMING_2 0x14904cc8
-#define CFG_DDR_MODE_1 0x00480432
-#define CFG_DDR_MODE_2 0x00000000
-#define CFG_DDR_INTERVAL 0x06180100
-#define CFG_DDR_DATA_INIT 0xdeadbeef
-#define CFG_DDR_CLK_CTRL 0x03800000
-#define CFG_DDR_OCD_CTRL 0x00000000
-#define CFG_DDR_OCD_STATUS 0x00000000
-#define CFG_DDR_CONTROL 0xe3008000 /* Type = DDR2 */
-#define CFG_DDR_CONTROL2 0x04400010
-
-#define CFG_DDR_ERR_INT_EN 0x00000000
-#define CFG_DDR_ERR_DIS 0x00000000
-#define CFG_DDR_SBE 0x000f0000
+#define CONFIG_SYS_DDR_CS0_BNDS 0x0000000F
+#define CONFIG_SYS_DDR_CS0_CONFIG 0x80010202 /* Enable, no interleaving */
+#define CONFIG_SYS_DDR_TIMING_3 0x00000000
+#define CONFIG_SYS_DDR_TIMING_0 0x00260802
+#define CONFIG_SYS_DDR_TIMING_1 0x3935d322
+#define CONFIG_SYS_DDR_TIMING_2 0x14904cc8
+#define CONFIG_SYS_DDR_MODE_1 0x00480432
+#define CONFIG_SYS_DDR_MODE_2 0x00000000
+#define CONFIG_SYS_DDR_INTERVAL 0x06180100
+#define CONFIG_SYS_DDR_DATA_INIT 0xdeadbeef
+#define CONFIG_SYS_DDR_CLK_CTRL 0x03800000
+#define CONFIG_SYS_DDR_OCD_CTRL 0x00000000
+#define CONFIG_SYS_DDR_OCD_STATUS 0x00000000
+#define CONFIG_SYS_DDR_CONTROL 0xe3008000 /* Type = DDR2 */
+#define CONFIG_SYS_DDR_CONTROL2 0x04400010
+
+#define CONFIG_SYS_DDR_ERR_INT_EN 0x00000000
+#define CONFIG_SYS_DDR_ERR_DIS 0x00000000
+#define CONFIG_SYS_DDR_SBE 0x000f0000
/*
* FIXME: Not used in fixed_sdram function
*/
-#define CFG_DDR_MODE 0x00000022
-#define CFG_DDR_CS1_BNDS 0x00000000
-#define CFG_DDR_CS2_BNDS 0x00000FFF /* Not done */
-#define CFG_DDR_CS3_BNDS 0x00000FFF /* Not done */
-#define CFG_DDR_CS4_BNDS 0x00000FFF /* Not done */
-#define CFG_DDR_CS5_BNDS 0x00000FFF /* Not done */
+#define CONFIG_SYS_DDR_MODE 0x00000022
+#define CONFIG_SYS_DDR_CS1_BNDS 0x00000000
+#define CONFIG_SYS_DDR_CS2_BNDS 0x00000FFF /* Not done */
+#define CONFIG_SYS_DDR_CS3_BNDS 0x00000FFF /* Not done */
+#define CONFIG_SYS_DDR_CS4_BNDS 0x00000FFF /* Not done */
+#define CONFIG_SYS_DDR_CS5_BNDS 0x00000FFF /* Not done */
#endif
#define CONFIG_ID_EEPROM
-#define CFG_I2C_EEPROM_NXID
+#define CONFIG_SYS_I2C_EEPROM_NXID
#define CONFIG_ID_EEPROM
-#define CFG_I2C_EEPROM_ADDR 0x57
-#define CFG_I2C_EEPROM_ADDR_LEN 1
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
-#define CFG_FLASH_BASE 0xf0000000 /* start of FLASH 128M */
-#define CFG_FLASH_BASE2 0xf8000000
+#define CONFIG_SYS_FLASH_BASE 0xf0000000 /* start of FLASH 128M */
+#define CONFIG_SYS_FLASH_BASE2 0xf8000000
-#define CFG_FLASH_BANKS_LIST {CFG_FLASH_BASE, CFG_FLASH_BASE2}
+#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE2}
-#define CFG_BR0_PRELIM 0xf8001001 /* port size 16bit */
-#define CFG_OR0_PRELIM 0xf8006e65 /* 128MB NOR Flash*/
+#define CONFIG_SYS_BR0_PRELIM 0xf8001001 /* port size 16bit */
+#define CONFIG_SYS_OR0_PRELIM 0xf8006e65 /* 128MB NOR Flash*/
-#define CFG_BR1_PRELIM 0xf0001001 /* port size 16bit */
-#define CFG_OR1_PRELIM 0xf8006e65 /* 128MB Promjet */
+#define CONFIG_SYS_BR1_PRELIM 0xf0001001 /* port size 16bit */
+#define CONFIG_SYS_OR1_PRELIM 0xf8006e65 /* 128MB Promjet */
#if 0 /* TODO */
-#define CFG_BR2_PRELIM 0xf0000000
-#define CFG_OR2_PRELIM 0xf0000000 /* 256MB NAND Flash - bank 1 */
+#define CONFIG_SYS_BR2_PRELIM 0xf0000000
+#define CONFIG_SYS_OR2_PRELIM 0xf0000000 /* 256MB NAND Flash - bank 1 */
#endif
-#define CFG_BR3_PRELIM 0xe8000801 /* port size 8bit */
-#define CFG_OR3_PRELIM 0xfff06ff7 /* 1MB PIXIS area*/
+#define CONFIG_SYS_BR3_PRELIM 0xe8000801 /* port size 8bit */
+#define CONFIG_SYS_OR3_PRELIM 0xfff06ff7 /* 1MB PIXIS area*/
#define CONFIG_FSL_PIXIS 1 /* use common PIXIS code */
@@ -179,67 +179,67 @@
#define PIXIS_VSPEED1 0x18 /* VELA VSpeed 1 */
#define PIXIS_VCLKH 0x19 /* VELA VCLKH register */
#define PIXIS_VCLKL 0x1A /* VELA VCLKL register */
-#define CFG_PIXIS_VBOOT_MASK 0x0C /* Reset altbank mask*/
+#define CONFIG_SYS_PIXIS_VBOOT_MASK 0x0C /* Reset altbank mask*/
-#define CFG_MAX_FLASH_BANKS 2 /* number of banks */
-#define CFG_MAX_FLASH_SECT 1024 /* sectors per device */
+#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */
-#undef CFG_FLASH_CHECKSUM
-#define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
-#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
-#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */
+#undef CONFIG_SYS_FLASH_CHECKSUM
+#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
+#define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */
#define CONFIG_FLASH_CFI_DRIVER
-#define CFG_FLASH_CFI
-#define CFG_FLASH_EMPTY_INFO
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_SYS_FLASH_EMPTY_INFO
-#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
-#define CFG_RAMBOOT
+#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
+#define CONFIG_SYS_RAMBOOT
#else
-#undef CFG_RAMBOOT
+#undef CONFIG_SYS_RAMBOOT
#endif
-#if defined(CFG_RAMBOOT)
+#if defined(CONFIG_SYS_RAMBOOT)
#undef CONFIG_SPD_EEPROM
-#define CFG_SDRAM_SIZE 256
+#define CONFIG_SYS_SDRAM_SIZE 256
#endif
#undef CONFIG_CLOCKS_IN_MHZ
#define CONFIG_L1_INIT_RAM
-#define CFG_INIT_RAM_LOCK 1
-#ifndef CFG_INIT_RAM_LOCK
-#define CFG_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */
+#define CONFIG_SYS_INIT_RAM_LOCK 1
+#ifndef CONFIG_SYS_INIT_RAM_LOCK
+#define CONFIG_SYS_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */
#else
-#define CFG_INIT_RAM_ADDR 0xe4000000 /* Initial RAM address */
+#define CONFIG_SYS_INIT_RAM_ADDR 0xe4000000 /* Initial RAM address */
#endif
-#define CFG_INIT_RAM_END 0x4000 /* End of used area in RAM */
+#define CONFIG_SYS_INIT_RAM_END 0x4000 /* End of used area in RAM */
-#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */
-#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+#define CONFIG_SYS_GBL_DATA_SIZE 128 /* num bytes initial data */
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-#define CFG_MONITOR_LEN (512 * 1024) /* Reserve 512 KB for Mon */
-#define CFG_MALLOC_LEN (6 * 1024 * 1024) /* Reserved for malloc */
+#define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 KB for Mon */
+#define CONFIG_SYS_MALLOC_LEN (6 * 1024 * 1024) /* Reserved for malloc */
/* Serial Port */
#define CONFIG_CONS_INDEX 1
#undef CONFIG_SERIAL_SOFTWARE_FIFO
-#define CFG_NS16550
-#define CFG_NS16550_SERIAL
-#define CFG_NS16550_REG_SIZE 1
-#define CFG_NS16550_CLK get_bus_freq(0)
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE 1
+#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
-#define CFG_BAUDRATE_TABLE \
+#define CONFIG_SYS_BAUDRATE_TABLE \
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
-#define CFG_NS16550_COM1 (CFG_CCSRBAR+0x4500)
-#define CFG_NS16550_COM2 (CFG_CCSRBAR+0x4600)
+#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500)
+#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600)
/* Use the HUSH parser */
-#define CFG_HUSH_PARSER
-#ifdef CFG_HUSH_PARSER
-#define CFG_PROMPT_HUSH_PS2 "> "
+#define CONFIG_SYS_HUSH_PARSER
+#ifdef CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
#endif
/*
@@ -253,8 +253,8 @@
/* maximum size of the flat tree (8K) */
#define OF_FLAT_TREE_MAX_SIZE 8192
-#define CFG_64BIT_VSPRINTF 1
-#define CFG_64BIT_STRTOUL 1
+#define CONFIG_SYS_64BIT_VSPRINTF 1
+#define CONFIG_SYS_64BIT_STRTOUL 1
/*
* I2C
@@ -262,46 +262,46 @@
#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
#define CONFIG_HARD_I2C /* I2C with hardware support*/
#undef CONFIG_SOFT_I2C /* I2C bit-banged */
-#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CFG_I2C_SLAVE 0x7F
-#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */
-#define CFG_I2C_OFFSET 0x3000
+#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
+#define CONFIG_SYS_I2C_SLAVE 0x7F
+#define CONFIG_SYS_I2C_NOPROBES {0x69} /* Don't probe these addrs */
+#define CONFIG_SYS_I2C_OFFSET 0x3000
/*
* General PCI
* Addresses are mapped 1-1.
*/
-#define CFG_PCI1_MEM_BASE 0x80000000
-#define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE
-#define CFG_PCI1_MEM_SIZE 0x10000000 /* 256M */
-#define CFG_PCI1_IO_BASE 0x00000000
-#define CFG_PCI1_IO_PHYS 0xe1000000
-#define CFG_PCI1_IO_SIZE 0x00100000 /* 1M */
+#define CONFIG_SYS_PCI1_MEM_BASE 0x80000000
+#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE
+#define CONFIG_SYS_PCI1_MEM_SIZE 0x10000000 /* 256M */
+#define CONFIG_SYS_PCI1_IO_BASE 0x00000000
+#define CONFIG_SYS_PCI1_IO_PHYS 0xe1000000
+#define CONFIG_SYS_PCI1_IO_SIZE 0x00100000 /* 1M */
/* PCI view of System Memory */
-#define CFG_PCI_MEMORY_BUS 0x00000000
-#define CFG_PCI_MEMORY_PHYS 0x00000000
-#define CFG_PCI_MEMORY_SIZE 0x80000000
+#define CONFIG_SYS_PCI_MEMORY_BUS 0x00000000
+#define CONFIG_SYS_PCI_MEMORY_PHYS 0x00000000
+#define CONFIG_SYS_PCI_MEMORY_SIZE 0x80000000
/* For RTL8139 */
#define KSEG1ADDR(x) ({u32 _x = le32_to_cpu(*(u32 *)(x)); (&_x); })
#define _IO_BASE 0x00000000
/* controller 1, Base address 0xa000 */
-#define CFG_PCIE1_MEM_BASE 0xa0000000
-#define CFG_PCIE1_MEM_PHYS CFG_PCIE1_MEM_BASE
-#define CFG_PCIE1_MEM_SIZE 0x10000000 /* 256M */
-#define CFG_PCIE1_IO_BASE 0x00000000
-#define CFG_PCIE1_IO_PHYS 0xe3000000
-#define CFG_PCIE1_IO_SIZE 0x00100000 /* 1M */
+#define CONFIG_SYS_PCIE1_MEM_BASE 0xa0000000
+#define CONFIG_SYS_PCIE1_MEM_PHYS CONFIG_SYS_PCIE1_MEM_BASE
+#define CONFIG_SYS_PCIE1_MEM_SIZE 0x10000000 /* 256M */
+#define CONFIG_SYS_PCIE1_IO_BASE 0x00000000
+#define CONFIG_SYS_PCIE1_IO_PHYS 0xe3000000
+#define CONFIG_SYS_PCIE1_IO_SIZE 0x00100000 /* 1M */
/* controller 2, Base Address 0x9000 */
-#define CFG_PCIE2_MEM_BASE 0x90000000
-#define CFG_PCIE2_MEM_PHYS CFG_PCIE2_MEM_BASE
-#define CFG_PCIE2_MEM_SIZE 0x10000000 /* 256M */
-#define CFG_PCIE2_IO_BASE 0x00000000 /* reuse mem LAW */
-#define CFG_PCIE2_IO_PHYS 0xe2000000
-#define CFG_PCIE2_IO_SIZE 0x00100000 /* 1M */
+#define CONFIG_SYS_PCIE2_MEM_BASE 0x90000000
+#define CONFIG_SYS_PCIE2_MEM_PHYS CONFIG_SYS_PCIE2_MEM_BASE
+#define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000 /* 256M */
+#define CONFIG_SYS_PCIE2_IO_BASE 0x00000000 /* reuse mem LAW */
+#define CONFIG_SYS_PCIE2_IO_PHYS 0xe2000000
+#define CONFIG_SYS_PCIE2_IO_SIZE 0x00100000 /* 1M */
#if defined(CONFIG_PCI)
@@ -324,11 +324,11 @@
#define CONFIG_PCI_OHCI 1
#define CONFIG_USB_OHCI_NEW 1
#define CONFIG_USB_KEYBOARD 1
-#define CFG_DEVICE_DEREGISTER
-#define CFG_USB_EVENT_POLL 1
-#define CFG_USB_OHCI_SLOT_NAME "ohci_pci"
-#define CFG_USB_OHCI_MAX_ROOT_PORTS 15
-#define CFG_OHCI_SWAP_REG_ACCESS 1
+#define CONFIG_SYS_DEVICE_DEREGISTER
+#define CONFIG_SYS_USB_EVENT_POLL 1
+#define CONFIG_SYS_USB_OHCI_SLOT_NAME "ohci_pci"
+#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15
+#define CONFIG_SYS_OHCI_SWAP_REG_ACCESS 1
#if !defined(CONFIG_PCI_PNP)
#define PCI_ENET0_IOADDR 0xe0000000
@@ -341,10 +341,10 @@
#ifdef CONFIG_SCSI_AHCI
#define CONFIG_SATA_ULI5288
-#define CFG_SCSI_MAX_SCSI_ID 4
-#define CFG_SCSI_MAX_LUN 1
-#define CFG_SCSI_MAX_DEVICE (CFG_SCSI_MAX_SCSI_ID * CFG_SCSI_MAX_LUN)
-#define CFG_SCSI_MAXDEVICE CFG_SCSI_MAX_DEVICE
+#define CONFIG_SYS_SCSI_MAX_SCSI_ID 4
+#define CONFIG_SYS_SCSI_MAX_LUN 1
+#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * CONFIG_SYS_SCSI_MAX_LUN)
+#define CONFIG_SYS_SCSI_MAXDEVICE CONFIG_SYS_SCSI_MAX_DEVICE
#endif
#endif /* CONFIG_PCI */
@@ -353,10 +353,10 @@
* BAT0 2G Cacheable, non-guarded
* 0x0000_0000 2G DDR
*/
-#define CFG_DBAT0L (BATL_PP_RW | BATL_MEMCOHERENCE)
-#define CFG_DBAT0U (BATU_BL_2G | BATU_VS | BATU_VP)
-#define CFG_IBAT0L (BATL_PP_RW | BATL_MEMCOHERENCE )
-#define CFG_IBAT0U CFG_DBAT0U
+#define CONFIG_SYS_DBAT0L (BATL_PP_RW | BATL_MEMCOHERENCE)
+#define CONFIG_SYS_DBAT0U (BATU_BL_2G | BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT0L (BATL_PP_RW | BATL_MEMCOHERENCE )
+#define CONFIG_SYS_IBAT0U CONFIG_SYS_DBAT0U
/*
* BAT1 1G Cache-inhibited, guarded
@@ -365,22 +365,22 @@
* 0x9000_0000 256M PCI-Express 2 Memory
*/
-#define CFG_DBAT1L (CFG_PCI1_MEM_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT \
+#define CONFIG_SYS_DBAT1L (CONFIG_SYS_PCI1_MEM_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT \
| BATL_GUARDEDSTORAGE)
-#define CFG_DBAT1U (CFG_PCI1_MEM_PHYS | BATU_BL_1G | BATU_VS | BATU_VP)
-#define CFG_IBAT1L (CFG_PCI1_MEM_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT)
-#define CFG_IBAT1U CFG_DBAT1U
+#define CONFIG_SYS_DBAT1U (CONFIG_SYS_PCI1_MEM_PHYS | BATU_BL_1G | BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT1L (CONFIG_SYS_PCI1_MEM_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT)
+#define CONFIG_SYS_IBAT1U CONFIG_SYS_DBAT1U
/*
* BAT2 16M Cache-inhibited, guarded
* 0xe100_0000 1M PCI-1 I/O
*/
-#define CFG_DBAT2L (CFG_PCI1_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT \
+#define CONFIG_SYS_DBAT2L (CONFIG_SYS_PCI1_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT \
| BATL_GUARDEDSTORAGE)
-#define CFG_DBAT2U (CFG_PCI1_IO_PHYS | BATU_BL_16M | BATU_VS | BATU_VP)
-#define CFG_IBAT2L (CFG_PCI1_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT)
-#define CFG_IBAT2U CFG_DBAT2U
+#define CONFIG_SYS_DBAT2U (CONFIG_SYS_PCI1_IO_PHYS | BATU_BL_16M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT2L (CONFIG_SYS_PCI1_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT)
+#define CONFIG_SYS_IBAT2U CONFIG_SYS_DBAT2U
/*
* BAT3 32M Cache-inhibited, guarded
@@ -388,68 +388,68 @@
* 0xe300_0000 1M PCI-Express 1 I/O
*/
-#define CFG_DBAT3L (CFG_PCIE2_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT \
+#define CONFIG_SYS_DBAT3L (CONFIG_SYS_PCIE2_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT \
| BATL_GUARDEDSTORAGE)
-#define CFG_DBAT3U (CFG_PCIE2_IO_PHYS | BATU_BL_32M | BATU_VS | BATU_VP)
-#define CFG_IBAT3L (CFG_PCIE2_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT)
-#define CFG_IBAT3U CFG_DBAT3U
+#define CONFIG_SYS_DBAT3U (CONFIG_SYS_PCIE2_IO_PHYS | BATU_BL_32M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT3L (CONFIG_SYS_PCIE2_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT)
+#define CONFIG_SYS_IBAT3U CONFIG_SYS_DBAT3U
/*
* BAT4 4M Cache-inhibited, guarded
* 0xe000_0000 4M CCSR
*/
-#define CFG_DBAT4L (CFG_CCSRBAR | BATL_PP_RW | BATL_CACHEINHIBIT \
+#define CONFIG_SYS_DBAT4L (CONFIG_SYS_CCSRBAR | BATL_PP_RW | BATL_CACHEINHIBIT \
| BATL_GUARDEDSTORAGE)
-#define CFG_DBAT4U (CFG_CCSRBAR | BATU_BL_1M | BATU_VS | BATU_VP)
-#define CFG_IBAT4L (CFG_CCSRBAR | BATL_PP_RW | BATL_CACHEINHIBIT)
-#define CFG_IBAT4U CFG_DBAT4U
+#define CONFIG_SYS_DBAT4U (CONFIG_SYS_CCSRBAR | BATU_BL_1M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT4L (CONFIG_SYS_CCSRBAR | BATL_PP_RW | BATL_CACHEINHIBIT)
+#define CONFIG_SYS_IBAT4U CONFIG_SYS_DBAT4U
/*
* BAT5 128K Cacheable, non-guarded
* 0xe400_0000 128K Init RAM for stack in the CPU DCache (no backing memory)
*/
-#define CFG_DBAT5L (CFG_INIT_RAM_ADDR | BATL_PP_RW | BATL_MEMCOHERENCE)
-#define CFG_DBAT5U (CFG_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
-#define CFG_IBAT5L CFG_DBAT5L
-#define CFG_IBAT5U CFG_DBAT5U
+#define CONFIG_SYS_DBAT5L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW | BATL_MEMCOHERENCE)
+#define CONFIG_SYS_DBAT5U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT5L CONFIG_SYS_DBAT5L
+#define CONFIG_SYS_IBAT5U CONFIG_SYS_DBAT5U
/*
* BAT6 256M Cache-inhibited, guarded
* 0xf000_0000 256M FLASH
*/
-#define CFG_DBAT6L (CFG_FLASH_BASE | BATL_PP_RW | BATL_CACHEINHIBIT \
+#define CONFIG_SYS_DBAT6L (CONFIG_SYS_FLASH_BASE | BATL_PP_RW | BATL_CACHEINHIBIT \
| BATL_GUARDEDSTORAGE)
-#define CFG_DBAT6U (CFG_FLASH_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
-#define CFG_IBAT6L (CFG_FLASH_BASE | BATL_PP_RW | BATL_MEMCOHERENCE)
-#define CFG_IBAT6U CFG_DBAT6U
+#define CONFIG_SYS_DBAT6U (CONFIG_SYS_FLASH_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT6L (CONFIG_SYS_FLASH_BASE | BATL_PP_RW | BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT6U CONFIG_SYS_DBAT6U
/*
* BAT7 4M Cache-inhibited, guarded
* 0xe800_0000 4M PIXIS
*/
-#define CFG_DBAT7L (PIXIS_BASE | BATL_PP_RW | BATL_CACHEINHIBIT \
+#define CONFIG_SYS_DBAT7L (PIXIS_BASE | BATL_PP_RW | BATL_CACHEINHIBIT \
| BATL_GUARDEDSTORAGE)
-#define CFG_DBAT7U (PIXIS_BASE | BATU_BL_1M | BATU_VS | BATU_VP)
-#define CFG_IBAT7L (PIXIS_BASE | BATL_PP_RW | BATL_CACHEINHIBIT)
-#define CFG_IBAT7U CFG_DBAT7U
+#define CONFIG_SYS_DBAT7U (PIXIS_BASE | BATU_BL_1M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT7L (PIXIS_BASE | BATL_PP_RW | BATL_CACHEINHIBIT)
+#define CONFIG_SYS_IBAT7U CONFIG_SYS_DBAT7U
/*
* Environment
*/
-#ifndef CFG_RAMBOOT
+#ifndef CONFIG_SYS_RAMBOOT
#define CONFIG_ENV_IS_IN_FLASH 1
-#define CONFIG_ENV_ADDR (CFG_MONITOR_BASE + CFG_MONITOR_LEN)
+#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
#define CONFIG_ENV_SECT_SIZE 0x20000 /* 126k (one sector) for env */
#define CONFIG_ENV_SIZE 0x2000
#else
#define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
-#define CONFIG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000)
+#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
#define CONFIG_ENV_SIZE 0x2000
#endif
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
/*
@@ -470,7 +470,7 @@
#define CONFIG_CMD_I2C
#define CONFIG_CMD_MII
-#if defined(CFG_RAMBOOT)
+#if defined(CONFIG_SYS_RAMBOOT)
#undef CONFIG_CMD_ENV
#endif
@@ -483,7 +483,7 @@
#define CONFIG_WATCHDOG /* watchdog enabled */
-#define CFG_WATCHDOG_FREQ 5000 /* Feed interval, 5s */
+#define CONFIG_SYS_WATCHDOG_FREQ 5000 /* Feed interval, 5s */
/*DIU Configuration*/
#define DIU_CONNECT_TO_DVI /* DIU controller connects to DVI encoder*/
@@ -491,28 +491,28 @@
/*
* Miscellaneous configurable options
*/
-#define CFG_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
#define CONFIG_CMDLINE_EDITING /* Command-line editing */
-#define CFG_LOAD_ADDR 0x2000000 /* default load address */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
+#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_HZ 1000 /* decrementer freq: 1ms ticks */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
+#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/
+#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/
/*
* Internal Definitions