summaryrefslogtreecommitdiff
path: root/include/configs/sbc8548.h
diff options
context:
space:
mode:
Diffstat (limited to 'include/configs/sbc8548.h')
-rw-r--r--include/configs/sbc8548.h260
1 files changed, 130 insertions, 130 deletions
diff --git a/include/configs/sbc8548.h b/include/configs/sbc8548.h
index 9d436c6..54f3e66 100644
--- a/include/configs/sbc8548.h
+++ b/include/configs/sbc8548.h
@@ -69,22 +69,22 @@
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */
-#undef CFG_DRAM_TEST /* memory test, takes time */
-#define CFG_MEMTEST_START 0x00200000 /* memtest works on */
-#define CFG_MEMTEST_END 0x00400000
+#undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */
+#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0x00400000
/*
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*/
-#define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
-#define CFG_CCSRBAR 0xe0000000 /* relocated CCSRBAR */
-#define CFG_CCSRBAR_PHYS CFG_CCSRBAR /* physical addr of CCSRBAR */
-#define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */
+#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
+#define CONFIG_SYS_CCSRBAR 0xe0000000 /* relocated CCSRBAR */
+#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of CCSRBAR */
+#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */
-#define CFG_PCI1_ADDR (CFG_CCSRBAR+0x8000)
-#define CFG_PCI2_ADDR (CFG_CCSRBAR+0x9000)
-#define CFG_PCIE1_ADDR (CFG_CCSRBAR+0xa000)
+#define CONFIG_SYS_PCI1_ADDR (CONFIG_SYS_CCSRBAR+0x8000)
+#define CONFIG_SYS_PCI2_ADDR (CONFIG_SYS_CCSRBAR+0x9000)
+#define CONFIG_SYS_PCIE1_ADDR (CONFIG_SYS_CCSRBAR+0xa000)
/* DDR Setup */
#define CONFIG_FSL_DDR2
@@ -96,8 +96,8 @@
#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */
#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
-#define CFG_DDR_SDRAM_BASE 0x00000000
-#define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE
+#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
+#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
#define CONFIG_VERY_BIG_RAM
#define CONFIG_NUM_DDR_CONTROLLERS 1
@@ -111,7 +111,7 @@
* Make sure required options are set
*/
#ifndef CONFIG_SPD_EEPROM
- #define CFG_SDRAM_SIZE 256 /* DDR is 256MB */
+ #define CONFIG_SYS_SDRAM_SIZE 256 /* DDR is 256MB */
#endif
#undef CONFIG_CLOCKS_IN_MHZ
@@ -165,47 +165,47 @@
* 1111 1000 0000 0000 0110 1110 0110 0101 = f8006e65 OR6
*/
-#define CFG_BOOT_BLOCK 0xff800000 /* start of 8MB Flash */
-#define CFG_FLASH_BASE CFG_BOOT_BLOCK /* start of FLASH 16M */
+#define CONFIG_SYS_BOOT_BLOCK 0xff800000 /* start of 8MB Flash */
+#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_BOOT_BLOCK /* start of FLASH 16M */
-#define CFG_BR0_PRELIM 0xff800801
-#define CFG_BR6_PRELIM 0xfb801801
+#define CONFIG_SYS_BR0_PRELIM 0xff800801
+#define CONFIG_SYS_BR6_PRELIM 0xfb801801
-#define CFG_OR0_PRELIM 0xff806e65
-#define CFG_OR6_PRELIM 0xf8006e65
+#define CONFIG_SYS_OR0_PRELIM 0xff806e65
+#define CONFIG_SYS_OR6_PRELIM 0xf8006e65
-#define CFG_FLASH_BANKS_LIST {CFG_FLASH_BASE}
-#define CFG_MAX_FLASH_BANKS 1 /* number of banks */
-#define CFG_MAX_FLASH_SECT 128 /* sectors per device */
-#undef CFG_FLASH_CHECKSUM
-#define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
-#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
+#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE}
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 128 /* sectors per device */
+#undef CONFIG_SYS_FLASH_CHECKSUM
+#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
-#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */
+#define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */
#define CONFIG_FLASH_CFI_DRIVER
-#define CFG_FLASH_CFI
-#define CFG_FLASH_EMPTY_INFO
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_SYS_FLASH_EMPTY_INFO
/* CS5 = Local bus peripherals controlled by the EPLD */
-#define CFG_BR5_PRELIM 0xf8000801
-#define CFG_OR5_PRELIM 0xff006e65
-#define CFG_EPLD_BASE 0xf8000000
-#define CFG_LED_DISP_BASE 0xf8000000
-#define CFG_USER_SWITCHES_BASE 0xf8100000
-#define CFG_BD_REV 0xf8300000
-#define CFG_EEPROM_BASE 0xf8b00000
+#define CONFIG_SYS_BR5_PRELIM 0xf8000801
+#define CONFIG_SYS_OR5_PRELIM 0xff006e65
+#define CONFIG_SYS_EPLD_BASE 0xf8000000
+#define CONFIG_SYS_LED_DISP_BASE 0xf8000000
+#define CONFIG_SYS_USER_SWITCHES_BASE 0xf8100000
+#define CONFIG_SYS_BD_REV 0xf8300000
+#define CONFIG_SYS_EEPROM_BASE 0xf8b00000
/*
* SDRAM on the Local Bus
*/
-#define CFG_LBC_SDRAM_BASE 0xf0000000 /* Localbus SDRAM */
-#define CFG_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */
+#define CONFIG_SYS_LBC_SDRAM_BASE 0xf0000000 /* Localbus SDRAM */
+#define CONFIG_SYS_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */
/*
* Base Register 3 and Option Register 3 configure SDRAM.
- * The SDRAM base address, CFG_LBC_SDRAM_BASE, is 0xf0000000.
+ * The SDRAM base address, CONFIG_SYS_LBC_SDRAM_BASE, is 0xf0000000.
*
* For BR3, need:
* Base address of 0xf0000000 = BR[0:16] = 1111 0000 0000 0000 0
@@ -219,10 +219,10 @@
*
*/
-#define CFG_BR3_PRELIM 0xf0001861
+#define CONFIG_SYS_BR3_PRELIM 0xf0001861
/*
- * The SDRAM size in MB, CFG_LBC_SDRAM_SIZE, is 64.
+ * The SDRAM size in MB, CONFIG_SYS_LBC_SDRAM_SIZE, is 64.
*
* For OR3, need:
* 64MB mask for AM, OR3[0:7] = 1111 1100
@@ -235,35 +235,35 @@
* 1111 1100 0000 0000 0110 1100 1100 0000 = fc006cc0
*/
-#define CFG_OR3_PRELIM 0xfc006cc0
+#define CONFIG_SYS_OR3_PRELIM 0xfc006cc0
-#define CFG_LBC_LCRR 0x00000002 /* LB clock ratio reg */
-#define CFG_LBC_LBCR 0x00000000 /* LB config reg */
-#define CFG_LBC_LSRT 0x20000000 /* LB sdram refresh timer */
-#define CFG_LBC_MRTPR 0x00000000 /* LB refresh timer prescal*/
+#define CONFIG_SYS_LBC_LCRR 0x00000002 /* LB clock ratio reg */
+#define CONFIG_SYS_LBC_LBCR 0x00000000 /* LB config reg */
+#define CONFIG_SYS_LBC_LSRT 0x20000000 /* LB sdram refresh timer */
+#define CONFIG_SYS_LBC_MRTPR 0x00000000 /* LB refresh timer prescal*/
/*
* LSDMR masks
*/
-#define CFG_LBC_LSDMR_RFEN (1 << (31 - 1))
-#define CFG_LBC_LSDMR_BSMA1516 (3 << (31 - 10))
-#define CFG_LBC_LSDMR_BSMA1617 (4 << (31 - 10))
-#define CFG_LBC_LSDMR_RFCR16 (7 << (31 - 16))
-#define CFG_LBC_LSDMR_PRETOACT7 (7 << (31 - 19))
-#define CFG_LBC_LSDMR_ACTTORW7 (7 << (31 - 22))
-#define CFG_LBC_LSDMR_ACTTORW6 (6 << (31 - 22))
-#define CFG_LBC_LSDMR_BL8 (1 << (31 - 23))
-#define CFG_LBC_LSDMR_WRC4 (0 << (31 - 27))
-#define CFG_LBC_LSDMR_CL3 (3 << (31 - 31))
-
-#define CFG_LBC_LSDMR_OP_NORMAL (0 << (31 - 4))
-#define CFG_LBC_LSDMR_OP_ARFRSH (1 << (31 - 4))
-#define CFG_LBC_LSDMR_OP_SRFRSH (2 << (31 - 4))
-#define CFG_LBC_LSDMR_OP_MRW (3 << (31 - 4))
-#define CFG_LBC_LSDMR_OP_PRECH (4 << (31 - 4))
-#define CFG_LBC_LSDMR_OP_PCHALL (5 << (31 - 4))
-#define CFG_LBC_LSDMR_OP_ACTBNK (6 << (31 - 4))
-#define CFG_LBC_LSDMR_OP_RWINV (7 << (31 - 4))
+#define CONFIG_SYS_LBC_LSDMR_RFEN (1 << (31 - 1))
+#define CONFIG_SYS_LBC_LSDMR_BSMA1516 (3 << (31 - 10))
+#define CONFIG_SYS_LBC_LSDMR_BSMA1617 (4 << (31 - 10))
+#define CONFIG_SYS_LBC_LSDMR_RFCR16 (7 << (31 - 16))
+#define CONFIG_SYS_LBC_LSDMR_PRETOACT7 (7 << (31 - 19))
+#define CONFIG_SYS_LBC_LSDMR_ACTTORW7 (7 << (31 - 22))
+#define CONFIG_SYS_LBC_LSDMR_ACTTORW6 (6 << (31 - 22))
+#define CONFIG_SYS_LBC_LSDMR_BL8 (1 << (31 - 23))
+#define CONFIG_SYS_LBC_LSDMR_WRC4 (0 << (31 - 27))
+#define CONFIG_SYS_LBC_LSDMR_CL3 (3 << (31 - 31))
+
+#define CONFIG_SYS_LBC_LSDMR_OP_NORMAL (0 << (31 - 4))
+#define CONFIG_SYS_LBC_LSDMR_OP_ARFRSH (1 << (31 - 4))
+#define CONFIG_SYS_LBC_LSDMR_OP_SRFRSH (2 << (31 - 4))
+#define CONFIG_SYS_LBC_LSDMR_OP_MRW (3 << (31 - 4))
+#define CONFIG_SYS_LBC_LSDMR_OP_PRECH (4 << (31 - 4))
+#define CONFIG_SYS_LBC_LSDMR_OP_PCHALL (5 << (31 - 4))
+#define CONFIG_SYS_LBC_LSDMR_OP_ACTBNK (6 << (31 - 4))
+#define CONFIG_SYS_LBC_LSDMR_OP_RWINV (7 << (31 - 4))
/*
* Common settings for all Local Bus SDRAM commands.
@@ -271,47 +271,47 @@
* or BSMA1617 (for CPU 1.0) (old)
* is OR'ed in too.
*/
-#define CFG_LBC_LSDMR_COMMON ( CFG_LBC_LSDMR_RFCR16 \
- | CFG_LBC_LSDMR_PRETOACT7 \
- | CFG_LBC_LSDMR_ACTTORW7 \
- | CFG_LBC_LSDMR_BL8 \
- | CFG_LBC_LSDMR_WRC4 \
- | CFG_LBC_LSDMR_CL3 \
- | CFG_LBC_LSDMR_RFEN \
+#define CONFIG_SYS_LBC_LSDMR_COMMON ( CONFIG_SYS_LBC_LSDMR_RFCR16 \
+ | CONFIG_SYS_LBC_LSDMR_PRETOACT7 \
+ | CONFIG_SYS_LBC_LSDMR_ACTTORW7 \
+ | CONFIG_SYS_LBC_LSDMR_BL8 \
+ | CONFIG_SYS_LBC_LSDMR_WRC4 \
+ | CONFIG_SYS_LBC_LSDMR_CL3 \
+ | CONFIG_SYS_LBC_LSDMR_RFEN \
)
#define CONFIG_L1_INIT_RAM
-#define CFG_INIT_RAM_LOCK 1
-#define CFG_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */
-#define CFG_INIT_RAM_END 0x4000 /* End of used area in RAM */
+#define CONFIG_SYS_INIT_RAM_LOCK 1
+#define CONFIG_SYS_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */
+#define CONFIG_SYS_INIT_RAM_END 0x4000 /* End of used area in RAM */
-#define CFG_INIT_L2_ADDR 0xf8f80000 /* relocate boot L2SRAM */
+#define CONFIG_SYS_INIT_L2_ADDR 0xf8f80000 /* relocate boot L2SRAM */
-#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */
-#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+#define CONFIG_SYS_GBL_DATA_SIZE 128 /* num bytes initial data */
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
-#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
+#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
+#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
/* Serial Port */
#define CONFIG_CONS_INDEX 1
#undef CONFIG_SERIAL_SOFTWARE_FIFO
-#define CFG_NS16550
-#define CFG_NS16550_SERIAL
-#define CFG_NS16550_REG_SIZE 1
-#define CFG_NS16550_CLK 400000000 /* get_bus_freq(0) */
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE 1
+#define CONFIG_SYS_NS16550_CLK 400000000 /* get_bus_freq(0) */
-#define CFG_BAUDRATE_TABLE \
+#define CONFIG_SYS_BAUDRATE_TABLE \
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
-#define CFG_NS16550_COM1 (CFG_CCSRBAR+0x4500)
-#define CFG_NS16550_COM2 (CFG_CCSRBAR+0x4600)
+#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500)
+#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600)
/* Use the HUSH parser */
-#define CFG_HUSH_PARSER
-#ifdef CFG_HUSH_PARSER
-#define CFG_PROMPT_HUSH_PS2 "> "
+#define CONFIG_SYS_HUSH_PARSER
+#ifdef CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
#endif
/* pass open firmware flat tree */
@@ -325,48 +325,48 @@
#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
#define CONFIG_HARD_I2C /* I2C with hardware support*/
#undef CONFIG_SOFT_I2C /* I2C bit-banged */
-#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CFG_I2C_EEPROM_ADDR 0x50
-#define CFG_I2C_SLAVE 0x7F
-#define CFG_I2C_OFFSET 0x3000
+#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
+#define CONFIG_SYS_I2C_SLAVE 0x7F
+#define CONFIG_SYS_I2C_OFFSET 0x3000
/*
* General PCI
* Memory space is mapped 1-1, but I/O space must start from 0.
*/
-#define CFG_PCI_PHYS 0x80000000 /* 1G PCI TLB */
+#define CONFIG_SYS_PCI_PHYS 0x80000000 /* 1G PCI TLB */
-#define CFG_PCI1_MEM_BASE 0x80000000
-#define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE
-#define CFG_PCI1_MEM_SIZE 0x20000000 /* 512M */
-#define CFG_PCI1_IO_BASE 0x00000000
-#define CFG_PCI1_IO_PHYS 0xe2000000
-#define CFG_PCI1_IO_SIZE 0x00100000 /* 1M */
+#define CONFIG_SYS_PCI1_MEM_BASE 0x80000000
+#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE
+#define CONFIG_SYS_PCI1_MEM_SIZE 0x20000000 /* 512M */
+#define CONFIG_SYS_PCI1_IO_BASE 0x00000000
+#define CONFIG_SYS_PCI1_IO_PHYS 0xe2000000
+#define CONFIG_SYS_PCI1_IO_SIZE 0x00100000 /* 1M */
#ifdef CONFIG_PCI2
-#define CFG_PCI2_MEM_BASE 0xa0000000
-#define CFG_PCI2_MEM_PHYS CFG_PCI2_MEM_BASE
-#define CFG_PCI2_MEM_SIZE 0x20000000 /* 512M */
-#define CFG_PCI2_IO_BASE 0x00000000
-#define CFG_PCI2_IO_PHYS 0xe2800000
-#define CFG_PCI2_IO_SIZE 0x00100000 /* 1M */
+#define CONFIG_SYS_PCI2_MEM_BASE 0xa0000000
+#define CONFIG_SYS_PCI2_MEM_PHYS CONFIG_SYS_PCI2_MEM_BASE
+#define CONFIG_SYS_PCI2_MEM_SIZE 0x20000000 /* 512M */
+#define CONFIG_SYS_PCI2_IO_BASE 0x00000000
+#define CONFIG_SYS_PCI2_IO_PHYS 0xe2800000
+#define CONFIG_SYS_PCI2_IO_SIZE 0x00100000 /* 1M */
#endif
#ifdef CONFIG_PCIE1
-#define CFG_PCIE1_MEM_BASE 0xa0000000
-#define CFG_PCIE1_MEM_PHYS CFG_PCIE1_MEM_BASE
-#define CFG_PCIE1_MEM_SIZE 0x20000000 /* 512M */
-#define CFG_PCIE1_IO_BASE 0x00000000
-#define CFG_PCIE1_IO_PHYS 0xe3000000
-#define CFG_PCIE1_IO_SIZE 0x00100000 /* 1M */
+#define CONFIG_SYS_PCIE1_MEM_BASE 0xa0000000
+#define CONFIG_SYS_PCIE1_MEM_PHYS CONFIG_SYS_PCIE1_MEM_BASE
+#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */
+#define CONFIG_SYS_PCIE1_IO_BASE 0x00000000
+#define CONFIG_SYS_PCIE1_IO_PHYS 0xe3000000
+#define CONFIG_SYS_PCIE1_IO_SIZE 0x00100000 /* 1M */
#endif
#ifdef CONFIG_RIO
/*
* RapidIO MMU
*/
-#define CFG_RIO_MEM_BASE 0xC0000000
-#define CFG_RIO_MEM_SIZE 0x20000000 /* 512M */
+#define CONFIG_SYS_RIO_MEM_BASE 0xC0000000
+#define CONFIG_SYS_RIO_MEM_SIZE 0x20000000 /* 512M */
#endif
#ifdef CONFIG_LEGACY
@@ -388,9 +388,9 @@
#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
/* PCI view of System Memory */
-#define CFG_PCI_MEMORY_BUS 0x00000000
-#define CFG_PCI_MEMORY_PHYS 0x00000000
-#define CFG_PCI_MEMORY_SIZE 0x80000000
+#define CONFIG_SYS_PCI_MEMORY_BUS 0x00000000
+#define CONFIG_SYS_PCI_MEMORY_PHYS 0x00000000
+#define CONFIG_SYS_PCI_MEMORY_SIZE 0x80000000
#endif /* CONFIG_PCI */
@@ -435,12 +435,12 @@
* Environment
*/
#define CONFIG_ENV_IS_IN_FLASH 1
-#define CONFIG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000)
+#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + 0x40000)
#define CONFIG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */
#define CONFIG_ENV_SIZE 0x2000
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
/*
* BOOTP options
@@ -471,25 +471,25 @@
/*
* Miscellaneous configurable options
*/
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_LOAD_ADDR 0x2000000 /* default load address */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
+#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_HZ 1000 /* decrementer freq: 1ms ticks */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
+#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/
+#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/
/*
* Internal Definitions