summaryrefslogtreecommitdiff
path: root/include/configs/zeus.h
diff options
context:
space:
mode:
Diffstat (limited to 'include/configs/zeus.h')
-rw-r--r--include/configs/zeus.h169
1 files changed, 84 insertions, 85 deletions
diff --git a/include/configs/zeus.h b/include/configs/zeus.h
index d427095..b75e8a1 100644
--- a/include/configs/zeus.h
+++ b/include/configs/zeus.h
@@ -51,7 +51,7 @@
#define CONFIG_HAS_ETH1 1
#define CONFIG_PHY1_ADDR 0x11 /* EMAC1 PHY address */
#define CONFIG_NET_MULTI 1
-#define CFG_RX_ETH_BUFFER 16 /* Number of ethernet rx buffers & descriptors */
+#define CONFIG_SYS_RX_ETH_BUFFER 16 /* Number of ethernet rx buffers & descriptors */
#define CONFIG_PHY_RESET 1
#define CONFIG_PHY_RESET_DELAY 300 /* PHY RESET recovery delay */
@@ -84,21 +84,21 @@
#define CONFIG_CMD_REGINFO
/* POST support */
-#define CONFIG_POST (CFG_POST_MEMORY | \
- CFG_POST_CPU | \
- CFG_POST_CACHE | \
- CFG_POST_UART | \
- CFG_POST_ETHER)
+#define CONFIG_POST (CONFIG_SYS_POST_MEMORY | \
+ CONFIG_SYS_POST_CPU | \
+ CONFIG_SYS_POST_CACHE | \
+ CONFIG_SYS_POST_UART | \
+ CONFIG_SYS_POST_ETHER)
-#define CFG_POST_ETHER_EXT_LOOPBACK /* eth POST using ext loopack connector */
+#define CONFIG_SYS_POST_ETHER_EXT_LOOPBACK /* eth POST using ext loopack connector */
/* Define here the base-addresses of the UARTs to test in POST */
-#define CFG_POST_UART_TABLE {UART0_BASE}
+#define CONFIG_SYS_POST_UART_TABLE {UART0_BASE}
#define CONFIG_LOGBUFFER
-#define CFG_POST_CACHE_ADDR 0x00800000 /* free virtual address */
+#define CONFIG_SYS_POST_CACHE_ADDR 0x00800000 /* free virtual address */
-#define CFG_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */
#undef CONFIG_WATCHDOG /* watchdog disabled */
@@ -112,48 +112,48 @@
#define CONFIG_SDRAM_BANK1 1 /* init onboard SDRAM bank 1 */
/* SDRAM timings used in datasheet */
-#define CFG_SDRAM_CL 3 /* CAS latency */
-#define CFG_SDRAM_tRP 20 /* PRECHARGE command period */
-#define CFG_SDRAM_tRC 66 /* ACTIVE-to-ACTIVE command period */
-#define CFG_SDRAM_tRCD 20 /* ACTIVE-to-READ delay */
-#define CFG_SDRAM_tRFC 66 /* Auto refresh period */
+#define CONFIG_SYS_SDRAM_CL 3 /* CAS latency */
+#define CONFIG_SYS_SDRAM_tRP 20 /* PRECHARGE command period */
+#define CONFIG_SYS_SDRAM_tRC 66 /* ACTIVE-to-ACTIVE command period */
+#define CONFIG_SYS_SDRAM_tRCD 20 /* ACTIVE-to-READ delay */
+#define CONFIG_SYS_SDRAM_tRFC 66 /* Auto refresh period */
/*-----------------------------------------------------------------------
* Serial Port
*----------------------------------------------------------------------*/
-#undef CFG_EXT_SERIAL_CLOCK /* external serial clock */
-#define CFG_BASE_BAUD 691200
+#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* external serial clock */
+#define CONFIG_SYS_BASE_BAUD 691200
#define CONFIG_BAUDRATE 115200
#define CONFIG_SERIAL_MULTI
/* The following table includes the supported baudrates */
-#define CFG_BAUDRATE_TABLE \
+#define CONFIG_SYS_BAUDRATE_TABLE \
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400}
/*-----------------------------------------------------------------------
* Miscellaneous configurable options
*----------------------------------------------------------------------*/
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
-#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
+#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-#define CFG_LOAD_ADDR 0x100000 /* default load address */
-#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
+#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
+#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
#define CONFIG_LOOPW 1 /* enable loopw command */
@@ -166,18 +166,17 @@
*----------------------------------------------------------------------*/
#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
#undef CONFIG_SOFT_I2C /* I2C bit-banged */
-#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CFG_I2C_SLAVE 0x7F
+#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
+#define CONFIG_SYS_I2C_SLAVE 0x7F
/* these are for the ST M24C02 2kbit serial i2c eeprom */
-#define CFG_I2C_EEPROM_ADDR 0x50 /* base address */
-#define CFG_I2C_EEPROM_ADDR_LEN 1 /* bytes of address */
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* base address */
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* bytes of address */
/* mask of address bits that overflow into the "EEPROM chip address" */
-#define CFG_I2C_EEPROM_ADDR_OVERFLOW 0x07
+#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x07
-#define CFG_EEPROM_PAGE_WRITE_ENABLE 1 /* write eeprom in pages */
-#define CFG_EEPROM_PAGE_WRITE_BITS 3 /* 8 byte write page size */
-#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 /* 8 byte write page size */
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
/*
* The layout of the I2C EEPROM, used for bootstrap setup and for board-
@@ -191,44 +190,44 @@
/*-----------------------------------------------------------------------
* Start addresses for the final memory configuration
* (Set up by the startup code)
- * Please note that CFG_SDRAM_BASE _must_ start at 0
+ * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
*/
-#define CFG_SDRAM_BASE 0x00000000
-#define CFG_FLASH_BASE 0xFF000000
-#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Monitor */
-#define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */
-#define CFG_MONITOR_BASE (-CFG_MONITOR_LEN)
+#define CONFIG_SYS_SDRAM_BASE 0x00000000
+#define CONFIG_SYS_FLASH_BASE 0xFF000000
+#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Monitor */
+#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */
+#define CONFIG_SYS_MONITOR_BASE (-CONFIG_SYS_MONITOR_LEN)
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/*-----------------------------------------------------------------------
* FLASH organization
*/
-#define CFG_FLASH_CFI /* The flash is CFI compatible */
+#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */
#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */
-#define CFG_FLASH_BANKS_LIST { CFG_FLASH_BASE }
+#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
-#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define CFG_MAX_FLASH_SECT 512 /* max number of sectors on one chip */
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max number of sectors on one chip */
-#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
-#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
+#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
-#define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
-#define CFG_FLASH_PROTECTION 1 /* use hardware flash protection */
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
+#define CONFIG_SYS_FLASH_PROTECTION 1 /* use hardware flash protection */
-#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
-#define CFG_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash */
+#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
+#define CONFIG_SYS_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash */
#ifdef CONFIG_ENV_IS_IN_FLASH
#define CONFIG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */
-#define CONFIG_ENV_ADDR ((-CFG_MONITOR_LEN)-CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_ADDR ((-CONFIG_SYS_MONITOR_LEN)-CONFIG_ENV_SECT_SIZE)
#define CONFIG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */
/* Address and size of Redundant Environment Sector */
@@ -240,31 +239,31 @@
* Definitions for initial stack pointer and data area (in data cache)
*/
/* use on chip memory (OCM) for temperary stack until sdram is tested */
-#define CFG_TEMP_STACK_OCM 1
+#define CONFIG_SYS_TEMP_STACK_OCM 1
/* On Chip Memory location */
-#define CFG_OCM_DATA_ADDR 0xF8000000
-#define CFG_OCM_DATA_SIZE 0x1000
-#define CFG_INIT_RAM_ADDR CFG_OCM_DATA_ADDR /* inside of OCM */
-#define CFG_INIT_RAM_END CFG_OCM_DATA_SIZE /* End of used area in RAM */
+#define CONFIG_SYS_OCM_DATA_ADDR 0xF8000000
+#define CONFIG_SYS_OCM_DATA_SIZE 0x1000
+#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* inside of OCM */
+#define CONFIG_SYS_INIT_RAM_END CONFIG_SYS_OCM_DATA_SIZE /* End of used area in RAM */
-#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
-#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
/* reserve some memory for POST and BOOT limit info */
-#define CFG_INIT_SP_OFFSET (CFG_GBL_DATA_OFFSET - 16)
+#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_GBL_DATA_OFFSET - 16)
/* extra data in OCM */
-#define CFG_POST_WORD_ADDR (CFG_GBL_DATA_OFFSET - 4)
-#define CFG_POST_MAGIC (CFG_OCM_DATA_ADDR + CFG_GBL_DATA_OFFSET - 8)
-#define CFG_POST_VAL (CFG_OCM_DATA_ADDR + CFG_GBL_DATA_OFFSET - 12)
+#define CONFIG_SYS_POST_WORD_ADDR (CONFIG_SYS_GBL_DATA_OFFSET - 4)
+#define CONFIG_SYS_POST_MAGIC (CONFIG_SYS_OCM_DATA_ADDR + CONFIG_SYS_GBL_DATA_OFFSET - 8)
+#define CONFIG_SYS_POST_VAL (CONFIG_SYS_OCM_DATA_ADDR + CONFIG_SYS_GBL_DATA_OFFSET - 12)
/*-----------------------------------------------------------------------
* External Bus Controller (EBC) Setup
*/
/* Memory Bank 0 (Flash 16M) initialization */
-#define CFG_EBC_PB0AP 0x05815600
-#define CFG_EBC_PB0CR 0xFF09A000 /* BAS=0xFF0,BS=16MB,BU=R/W,BW=16bit */
+#define CONFIG_SYS_EBC_PB0AP 0x05815600
+#define CONFIG_SYS_EBC_PB0CR 0xFF09A000 /* BAS=0xFF0,BS=16MB,BU=R/W,BW=16bit */
/*-----------------------------------------------------------------------
* Definitions for GPIO setup (PPC405EP specific)
@@ -278,23 +277,23 @@
* GPIO0[28-29] - UART1 data signal input/output
* GPIO0[30-31] - EMAC0 and EMAC1 reject packet inputs
*/
-#define CFG_GPIO0_OSRH 0x15555550 /* Chip selects */
-#define CFG_GPIO0_OSRL 0x00000110 /* UART_DTR-pin 27 alt out */
-#define CFG_GPIO0_ISR1H 0x10000041 /* Pin 2, 12 is input */
-#define CFG_GPIO0_ISR1L 0x15505440 /* OUT: LEDs 22/23; IN: pin12,2, NVALID# */
-#define CFG_GPIO0_TSRH 0x00000000
-#define CFG_GPIO0_TSRL 0x00000000
-#define CFG_GPIO0_TCR 0xBFF68317 /* 3-state OUT: 22/23/29; 12,2 is not 3-state */
-#define CFG_GPIO0_ODR 0x00000000
-
-#define CFG_GPIO_SW_RESET 1
-#define CFG_GPIO_ZEUS_PE 12
-#define CFG_GPIO_LED_RED 22
-#define CFG_GPIO_LED_GREEN 23
+#define CONFIG_SYS_GPIO0_OSRH 0x15555550 /* Chip selects */
+#define CONFIG_SYS_GPIO0_OSRL 0x00000110 /* UART_DTR-pin 27 alt out */
+#define CONFIG_SYS_GPIO0_ISR1H 0x10000041 /* Pin 2, 12 is input */
+#define CONFIG_SYS_GPIO0_ISR1L 0x15505440 /* OUT: LEDs 22/23; IN: pin12,2, NVALID# */
+#define CONFIG_SYS_GPIO0_TSRH 0x00000000
+#define CONFIG_SYS_GPIO0_TSRL 0x00000000
+#define CONFIG_SYS_GPIO0_TCR 0xBFF68317 /* 3-state OUT: 22/23/29; 12,2 is not 3-state */
+#define CONFIG_SYS_GPIO0_ODR 0x00000000
+
+#define CONFIG_SYS_GPIO_SW_RESET 1
+#define CONFIG_SYS_GPIO_ZEUS_PE 12
+#define CONFIG_SYS_GPIO_LED_RED 22
+#define CONFIG_SYS_GPIO_LED_GREEN 23
/* Time in milli-seconds */
-#define CFG_TIME_POST 5000
-#define CFG_TIME_FACTORY_RESET 10000
+#define CONFIG_SYS_TIME_POST 5000
+#define CONFIG_SYS_TIME_FACTORY_RESET 10000
/*
* Internal Definitions