summaryrefslogtreecommitdiff
path: root/include/configs
diff options
context:
space:
mode:
Diffstat (limited to 'include/configs')
-rw-r--r--include/configs/ADS860.h360
-rw-r--r--include/configs/DK1C20.h11
-rw-r--r--include/configs/DUET_ADS.h53
-rw-r--r--include/configs/FADS823.h12
-rw-r--r--include/configs/FADS850SAR.h12
-rw-r--r--include/configs/FADS860T.h419
-rw-r--r--include/configs/MPC86xADS.h388
-rw-r--r--include/configs/PPChameleonEVB.h51
8 files changed, 130 insertions, 1176 deletions
diff --git a/include/configs/ADS860.h b/include/configs/ADS860.h
index 1b037c9..916272d 100644
--- a/include/configs/ADS860.h
+++ b/include/configs/ADS860.h
@@ -5,17 +5,14 @@
* Helmut Buchsbaum added bitvalues for BCSRx
*
* Copyright (c) 1998 Dan Malek (dmalek@jlc.net)
+ *
+ * Modified by, Yuli Barcohen, Arabella Software Ltd., yuli@arabellasw.com
+ *
+ * Values common to all FADS family boards are in board/fads/fads.h
*/
-/* ------------------------------------------------------------------------- */
-
-#ifndef _CONFIG_ADS860_H
-#define _CONFIG_ADS860_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
+#ifndef __CONFIG_H
+#define __CONFIG_H
/* Board type */
#define CONFIG_ADS 1 /* Old Motorola MPC821/860ADS */
@@ -38,351 +35,20 @@
#define CFG_8XX_FACT 12 /* Multiply by 12 */
#endif
-#define CONFIG_8xx_GCLK_FREQ ((CFG_8XX_XIN) * (CFG_8XX_FACT))
-
-#define CONFIG_DRAM_50MHZ 1
-
-#if 0
-#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
-#else
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-#endif
-
-#undef CONFIG_BOOTARGS
-#define CONFIG_BOOTCOMMAND \
- "dhcp;" \
- "setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) " \
- "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off;" \
- "bootm"
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#undef CFG_LOADS_BAUD_CHANGE /* don't allow baudrate change */
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | CONFIG_BOOTP_BOOTFILESIZE)
-
-#define CONFIG_COMMANDS (CONFIG_CMD_DFL \
- | CFG_CMD_DHCP \
- | CFG_CMD_IMMAP \
+#define CONFIG_COMMANDS (CONFIG_CMD_DFL \
+ | CFG_CMD_DHCP \
+ | CFG_CMD_IMMAP \
| CFG_CMD_PCMCIA \
- | CFG_CMD_PING \
+ | CFG_CMD_PING \
)
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
-
-/*
- * Miscellaneous configurable options
- */
-#undef CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=>" /* Monitor Command Prompt */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-
-#define CFG_MEMTEST_START 0x00100000 /* memtest works on */
-#define CFG_MEMTEST_END 0x00F00000 /* 1 ... 15 MB in DRAM */
+#define CONFIG_DRAM_50MHZ 1
-#define CFG_LOAD_ADDR 0x00100000
+#include "fads.h"
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
-
-#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-/*-----------------------------------------------------------------------
- * Internal Memory Mapped Register
- */
-#define CFG_IMMR 0xFF000000
-#define CFG_IMMR_SIZE ((uint)(64 * 1024))
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CFG_INIT_RAM_ADDR CFG_IMMR
-#define CFG_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */
-#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */
-#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CFG_SDRAM_BASE _must_ start at 0
- */
-#define CFG_SDRAM_BASE 0x00000000
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define CFG_FLASH_BASE TEXT_BASE
-#define CFG_FLASH_SIZE ((uint)(8 * 1024 * 1024)) /* max 8Mbyte */
-
-#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define CFG_MAX_FLASH_SECT 16 /* max number of sectors on one chip */
-
-#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
-#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
-
-#undef CFG_ENV_IS_IN_NVRAM
-#undef CFG_ENV_IS_IN_EEPROM
-#define CFG_ENV_IS_IN_FLASH 1
-
-#define CFG_ENV_SECT_SIZE 0x40000 /* see README - env sector total size */
-#define CFG_ENV_OFFSET CFG_ENV_SECT_SIZE
-#define CFG_ENV_SIZE 0x4000 /* Total Size of Environment */
-
-#define CFG_MONITOR_BASE CFG_FLASH_BASE
-#define CFG_MONITOR_LEN (256 << 10) /* Reserve one flash sector
- (256 KB) for monitor */
-#define CFG_MALLOC_LEN (384 << 10) /* Reserve 384 kB for malloc() */
-
-/* the other CS:s are determined by looking at parameters in BCSRx */
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */
-#endif
-
-/*-----------------------------------------------------------------------
- * I2C configuration
- */
-#if (CONFIG_COMMANDS & CFG_CMD_I2C)
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#define CFG_I2C_SPEED 400000 /* I2C speed and slave address defaults */
-#define CFG_I2C_SLAVE 0x7F
-#endif
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control 11-9
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
- */
-#if defined(CONFIG_WATCHDOG)
-#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
- SYPCR_SWE | SYPCR_SWRI | SYPCR_SWP)
-#else
-#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
-#endif
-
-/*-----------------------------------------------------------------------
- * SUMCR - SIU Module Configuration 11-6
- *-----------------------------------------------------------------------
- * PCMCIA config., multi-function pin tri-state
- */
-#define CFG_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
-
-/*-----------------------------------------------------------------------
- * TBSCR - Time Base Status and Control 11-26
- *-----------------------------------------------------------------------
- * Clear Reference Interrupt Status, Timebase freezing enabled
- */
-#define CFG_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBE)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control 11-31
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
- */
-#define CFG_PISCR (PISCR_PS | PISCR_PITF)
-
-/*-----------------------------------------------------------------------
- * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30
- *-----------------------------------------------------------------------
- * set the PLL, the low-power modes and the reset control (15-29)
- */
#define CFG_PLPRCR (((CFG_8XX_FACT-1) << PLPRCR_MF_SHIFT) | \
PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
-/*-----------------------------------------------------------------------
- * SCCR - System Clock and reset Control Register 15-27
- *-----------------------------------------------------------------------
- * Set clock output, timebase and RTC source and divider,
- * power management and some other internal clocks
- */
-#define SCCR_MASK SCCR_EBDF11
-#define CFG_SCCR (SCCR_TBS | SCCR_COM00 | SCCR_DFSYNC00 | \
- SCCR_DFBRG00 | SCCR_DFNL000 | SCCR_DFNH000 | \
- SCCR_DFLCD000 | SCCR_DFALCD00)
-
-
- /*-----------------------------------------------------------------------
- *
- *-----------------------------------------------------------------------
- *
- */
-#define CFG_DER 0
-
-/* Because of the way the 860 starts up and assigns CS0 the
-* entire address space, we have to set the memory controller
-* differently. Normally, you write the option register
-* first, and then enable the chip select by writing the
-* base register. For CS0, you must write the base register
-* first, followed by the option register.
-*/
-
-/*
- * Init Memory Controller:
- *
- * BR0 and OR0 (FLASH)
- * BR1 and OR1 (BCSR)
- */
-/* the other CS:s are determined by looking at parameters in BCSRx */
-
-#define BCSR_ADDR ((uint) 0xff010000)
-
-#define CFG_PRELIM_OR_AM 0xff800000 /* OR addr mask */
-
-/* FLASH timing: ACS = 10, TRLX = 1, CSNT = 1, SCY = 3, EHTR = 0 */
-#define CFG_OR_TIMING_FLASH (OR_CSNT_SAM | OR_ACS_DIV4 | OR_BI | OR_SCY_3_CLK | OR_TRLX)
-
-#define CFG_OR0_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH) /* 8 Mbyte until detected */
-#define CFG_BR0_PRELIM (CFG_FLASH_BASE | BR_V)
-
-/* BCSRx - Board Control and Status Registers */
-#define CFG_OR1_PRELIM 0xffff8110 /* 64Kbyte address space */
-#define CFG_BR1_PRELIM ((BCSR_ADDR) | BR_V )
-
-/*
- * Memory Periodic Timer Prescaler
- */
-
-/* refresh rate 15.6 us (= 64 ms / 4K = 62.4 / quad bursts) for <= 128 MBit */
-#define CFG_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */
-#define CFG_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */
-
-/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */
-#define CFG_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */
-#define CFG_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */
-
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
-
-
-/* values according to the manual */
-#define BCSR0 (BCSR_ADDR + 0x00)
-#define BCSR1 (BCSR_ADDR + 0x04)
-#define BCSR2 (BCSR_ADDR + 0x08)
-#define BCSR3 (BCSR_ADDR + 0x0c)
-
-
-/*-----------------------------------------------------------------------
- * PCMCIA stuff
- *-----------------------------------------------------------------------
- *
- */
-#ifdef CONFIG_MPC860
-#define PCMCIA_SLOT_A 1
-#endif
-
-#define CFG_PCMCIA_MEM_ADDR (0xE0000000)
-#define CFG_PCMCIA_MEM_SIZE ( 64 << 20 )
-#define CFG_PCMCIA_DMA_ADDR (0xE4000000)
-#define CFG_PCMCIA_DMA_SIZE ( 64 << 20 )
-#define CFG_PCMCIA_ATTRB_ADDR (0xE8000000)
-#define CFG_PCMCIA_ATTRB_SIZE ( 64 << 20 )
-#define CFG_PCMCIA_IO_ADDR (0xEC000000)
-#define CFG_PCMCIA_IO_SIZE ( 64 << 20 )
-
-/*-----------------------------------------------------------------------
- * IDE/ATA stuff
- *-----------------------------------------------------------------------
- */
-#define CONFIG_IDE_8xx_DIRECT 1 /* PCMCIA interface required */
-#undef CONFIG_IDE_LED /* LED for ide supported */
-#define CONFIG_IDE_RESET 1 /* reset for ide supported */
-
-#define CFG_IDE_MAXBUS 1 /* max. 2 IDE busses */
-#define CFG_IDE_MAXDEVICE (CFG_IDE_MAXBUS*2) /* max. 2 drives per IDE bus */
-
-#define CFG_PIO_MODE 0 /* IDE interface in PIO Mode 0 */
#define CFG_PC_IDE_RESET ((ushort)0x0008) /* PC 12 */
-#define CFG_ATA_BASE_ADDR CFG_PCMCIA_MEM_ADDR
-#define CFG_ATA_IDE0_OFFSET 0x0000
-
-#define CFG_ATA_DATA_OFFSET 0x0000 /* Offset for data I/O */
-#define CFG_ATA_REG_OFFSET 0x0080 /* Offset for normal register accesses */
-#define CFG_ATA_ALT_OFFSET 0x0100 /* Offset for alternate registers */
-
-#define CONFIG_DISK_SPINUP_TIME 1000000
-#undef CONFIG_DISK_SPINUP_TIME /* usinī Compact Flash */
-
-/* (F)ADS bitvalues by Helmut Buchsbaum
- * see MPC8xxADS User's Manual for a proper description
- * of the following structures
- */
-
-#define BCSR0_ERB ((uint)0x80000000)
-#define BCSR0_IP ((uint)0x40000000)
-#define BCSR0_BDIS ((uint)0x10000000)
-#define BCSR0_BPS_MASK ((uint)0x0C000000)
-#define BCSR0_ISB_MASK ((uint)0x01800000)
-#define BCSR0_DBGC_MASK ((uint)0x00600000)
-#define BCSR0_DBPC_MASK ((uint)0x00180000)
-#define BCSR0_EBDF_MASK ((uint)0x00060000)
-
-#define BCSR1_FLASH_EN ((uint)0x80000000)
-#define BCSR1_DRAM_EN ((uint)0x40000000)
-#define BCSR1_ETHEN ((uint)0x20000000)
-#define BCSR1_IRDEN ((uint)0x10000000)
-#define BCSR1_FLASH_CFG_EN ((uint)0x08000000)
-#define BCSR1_CNT_REG_EN_PROTECT ((uint)0x04000000)
-#define BCSR1_BCSR_EN ((uint)0x02000000)
-#define BCSR1_RS232EN_1 ((uint)0x01000000)
-#define BCSR1_PCCEN ((uint)0x00800000)
-#define BCSR1_PCCVCC0 ((uint)0x00400000)
-#define BCSR1_PCCVCCON BCSR1_PCCVCC0
-#define BCSR1_PCCVPP_MASK ((uint)0x00300000)
-#define BCSR1_DRAM_HALF_WORD ((uint)0x00080000)
-#define BCSR1_RS232EN_2 ((uint)0x00040000)
-#define BCSR1_SDRAM_EN ((uint)0x00020000)
-#define BCSR1_PCCVCC1 ((uint)0x00010000)
-
-#define BCSR2_FLASH_PD_MASK ((uint)0xF0000000)
-#define BCSR2_DRAM_PD_MASK ((uint)0x07800000)
-#define BCSR2_DRAM_PD_SHIFT (23)
-#define BCSR2_EXTTOLI_MASK ((uint)0x00780000)
-#define BCSR2_DBREVNR_MASK ((uint)0x00030000)
-
-#define BCSR3_DBID_MASK ((ushort)0x3800)
-#define BCSR3_CNT_REG_EN_PROTECT ((ushort)0x0400)
-#define BCSR3_BREVNR0 ((ushort)0x0080)
-#define BCSR3_FLASH_PD_MASK ((ushort)0x0070)
-#define BCSR3_BREVN1 ((ushort)0x0008)
-#define BCSR3_BREVN2_MASK ((ushort)0x0003)
-
-/* We don't use the 8259.
- */
-#define NR_8259_INTS 0
-
-/* Machine type
- */
-#define _MACH_8xx (_MACH_ads)
-
-#endif /* _CONFIG_ADS860_H */
+#endif /* __CONFIG_H */
diff --git a/include/configs/DK1C20.h b/include/configs/DK1C20.h
index 2b0b176..0d8e463 100644
--- a/include/configs/DK1C20.h
+++ b/include/configs/DK1C20.h
@@ -413,7 +413,7 @@
#endif
/*------------------------------------------------------------------------
- * Ethernet -- needs work!
+ * Ethernet
*----------------------------------------------------------------------*/
#if (CFG_NIOS_CPU_LAN_NUMS == 1)
@@ -642,6 +642,15 @@
#endif /* CFG_NIOS_CPU_PIO_NUMS */
/*------------------------------------------------------------------------
+ * ASMI - Active Serial Memory Interface.
+ *
+ * ASMI is for Cyclone devices only and only works when the configuration
+ * is loaded via JTAG or ASMI. Please see doc/README.dk1c20 for details.
+ *----------------------------------------------------------------------*/
+#define CONFIG_NIOS_ASMI /* Enable ASMI */
+#define CFG_NIOS_ASMIBASE 0x00920b00 /* ASMI base address */
+
+/*------------------------------------------------------------------------
* COMMANDS
*----------------------------------------------------------------------*/
#define CONFIG_COMMANDS (CFG_CMD_ALL & ~( \
diff --git a/include/configs/DUET_ADS.h b/include/configs/DUET_ADS.h
new file mode 100644
index 0000000..8a40257
--- /dev/null
+++ b/include/configs/DUET_ADS.h
@@ -0,0 +1,53 @@
+/*
+ * A collection of structures, addresses, and values associated with
+ * the Motorola DUET ADS board. Values common to all FADS family boards
+ * are in board/fads/fads.h
+ *
+ * Copyright (C) 2003 Arabella Software Ltd.
+ * Yuli Barcohen <yuli@arabellasw.com>
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/* Board type */
+#define CONFIG_DUET_ADS 1 /* Duet (MPC87x/88x) ADS */
+#define CONFIG_FADS 1 /* We are FADS compatible (more or less) */
+
+#define CONFIG_MPC885 1 /* MPC885 CPU (Duet family) */
+
+#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */
+#undef CONFIG_8xx_CONS_SMC2
+#undef CONFIG_8xx_CONS_NONE
+#define CONFIG_BAUDRATE 38400
+
+#define CFG_8XX_FACT 5 /* Multiply by 5 */
+#define CFG_8XX_XIN 10000000 /* 10 MHz in */
+
+#define CONFIG_SDRAM_50MHZ 1
+
+/*-----------------------------------------------------------------------
+ * PLPRCR - PLL, Low-Power, and Reset Control Register 14-22
+ *-----------------------------------------------------------------------
+ * set the PLL, the low-power modes and the reset control
+ */
+#define CFG_PLPRCR ((CFG_8XX_FACT << PLPRCR_MFI_SHIFT) | PLPRCR_TEXPS)
+
+#include "fads.h"
+
+#define CFG_PHYDEV_ADDR (BCSR_ADDR + 0x20000)
+
+#define CFG_OR5_PRELIM 0xFFFF8110 /* 64Kbyte address space */
+#define CFG_BR5_PRELIM (CFG_PHYDEV_ADDR | BR_PS_8 | BR_V)
+
+#define BCSR5 (CFG_PHYDEV_ADDR + 0x300)
+
+#define BCSR5_MII2_EN 0x40
+#define BCSR5_MII2_RST 0x20
+#define BCSR5_T1_RST 0x10
+#define BCSR5_ATM155_RST 0x08
+#define BCSR5_ATM25_RST 0x04
+#define BCSR5_MII1_EN 0x02
+#define BCSR5_MII1_RST 0x01
+
+#endif /* __CONFIG_H */
diff --git a/include/configs/FADS823.h b/include/configs/FADS823.h
index 3b201a7..4f3d397 100644
--- a/include/configs/FADS823.h
+++ b/include/configs/FADS823.h
@@ -66,8 +66,6 @@
* High Level Configuration Options
* (easy to change)
*/
-#include <mpc8xx_irq.h>
-
#define CONFIG_MPC823 1
#define CONFIG_MPC823FADS 1
#define CONFIG_FADS 1
@@ -433,14 +431,6 @@
#define CONFIG_DRAM_50MHZ 1
#define CONFIG_SDRAM_50MHZ
-#ifdef CONFIG_MPC860T
-
-/* Interrupt level assignments.
-*/
-#define FEC_INTERRUPT SIU_LEVEL1 /* FEC interrupt */
-
-#endif /* CONFIG_MPC860T */
-
/* We don't use the 8259.
*/
#define NR_8259_INTS 0
@@ -468,4 +458,6 @@
#define PCMCIA_SLOT_A 1
#endif
+#define CFG_DAUGHTERBOARD
+
#endif /* __CONFIG_H */
diff --git a/include/configs/FADS850SAR.h b/include/configs/FADS850SAR.h
index 3d04ef0..9e292ae 100644
--- a/include/configs/FADS850SAR.h
+++ b/include/configs/FADS850SAR.h
@@ -30,8 +30,6 @@
* High Level Configuration Options
* (easy to change)
*/
-#include <mpc8xx_irq.h>
-
#define CONFIG_MPC850 1
#define CONFIG_MPC850SAR 1
#define CONFIG_FADS 1
@@ -393,14 +391,6 @@
#define CONFIG_DRAM_50MHZ 1
#define CONFIG_SDRAM_50MHZ
-#ifdef CONFIG_MPC860T
-
-/* Interrupt level assignments.
-*/
-#define FEC_INTERRUPT SIU_LEVEL1 /* FEC interrupt */
-
-#endif /* CONFIG_MPC860T */
-
/* We don't use the 8259.
*/
#define NR_8259_INTS 0
@@ -420,4 +410,6 @@
#define PCMCIA_SLOT_A 1
#endif
+#define CFG_DAUGHTERBOARD
+
#endif /* __CONFIG_H */
diff --git a/include/configs/FADS860T.h b/include/configs/FADS860T.h
index 114603c..e57571b 100644
--- a/include/configs/FADS860T.h
+++ b/include/configs/FADS860T.h
@@ -5,32 +5,15 @@
* Helmut Buchsbaum added bitvalues for BCSRx
*
* Copyright (c) 1998 Dan Malek (dmalek@jlc.net)
+ *
+ * Modified by, Yuli Barcohen, Arabella Software Ltd., yuli@arabellasw.com
+ *
+ * Values common to all FADS family boards are in board/fads/fads.h
*/
-/*
- * 1999-nov-26: The FADS is using the following physical memorymap:
- *
- * ff020000 -> ff02ffff : pcmcia
- * ff010000 -> ff01ffff : BCSR connected to CS1, setup by 8xxrom
- * ff000000 -> ff00ffff : IMAP internal in the cpu
- * fe000000 -> ffnnnnnn : flash connected to CS0, setup by 8xxrom
- * 00000000 -> nnnnnnnn : sdram/dram setup by 8xxrom
- */
-
-/* ------------------------------------------------------------------------- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
#ifndef __CONFIG_H
#define __CONFIG_H
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
/* board type */
#define CONFIG_FADS 1 /* old/new FADS + new ADS */
@@ -51,403 +34,25 @@
# define CFG_8XX_XIN 5000000 /* 5 MHz in */
#endif
-#define MPC8XX_HZ ((CFG_8XX_XIN) * (CFG_8XX_FACT))
-
-/* should ALWAYS define this, measure_gclk in speed.c is unreliable */
-/* in general, we always know this for FADS+new ADS anyway */
-#define CONFIG_8xx_GCLK_FREQ MPC8XX_HZ
-
-#if 1
-#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
-#else
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-#endif
-
-#undef CONFIG_BOOTARGS
-#define CONFIG_BOOTCOMMAND \
- "bootp; " \
- "setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) " \
- "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off; " \
- "bootm"
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-/* ATA / IDE and partition support */
-#define CONFIG_MAC_PARTITION 1
-#define CONFIG_DOS_PARTITION 1
-#define CONFIG_ISO_PARTITION 1
-#undef CONFIG_ATAPI
-#define CONFIG_IDE_8xx_PCCARD 1 /* Use IDE with PC Card Adapter */
-#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
-#undef CONFIG_IDE_LED /* LED for ide not supported */
-#undef CONFIG_IDE_RESET /* reset for ide not supported */
-
-/* choose SCC1 ethernet (10BASET on motherboard)
- * or FEC ethernet (10/100 on daughterboard)
- */
-#if 0
-#define CONFIG_SCC1_ENET 1 /* use SCC1 ethernet */
-#undef CONFIG_FEC_ENET /* disable FEC ethernet */
-#else /* all 86x cores have FECs, if in doubt, use it */
-#undef CONFIG_SCC1_ENET /* disable SCC1 ethernet */
-#define CONFIG_FEC_ENET 1 /* use FEC ethernet */
-#define CFG_DISCOVER_PHY
-#endif
-#if defined(CONFIG_SCC1_ENET) && defined(CONFIG_FEC_ENET)
-#error Both CONFIG_SCC1_ENET and CONFIG_FEC_ENET configured
-#endif
-
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
-
-/*
- * Miscellaneous configurable options
- */
-#undef CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=>" /* Monitor Command Prompt */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-
-#define CFG_MEMTEST_START 0x0100000 /* memtest works on */
-#if (CFG_SDRAM_SIZE)
-#define CFG_MEMTEST_END CFG_SDRAM_SIZE /* 1 ... SDRAM_SIZE */
-#else
-#define CFG_MEMTEST_END 0x0400000 /* 1 ... 4 MB in DRAM */
-#endif
-
-#define CFG_LOAD_ADDR 0x00100000
-
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
-
-#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-/*----------------------------------------------------------------------
- * Internal Memory Mapped Register
- */
-#define CFG_IMMR 0xFF000000
-#define CFG_IMMR_SIZE ((uint)(64 * 1024))
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CFG_INIT_RAM_ADDR CFG_IMMR
-#define CFG_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */
-#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */
-#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CFG_SDRAM_BASE _must_ start at 0
- */
-#define CFG_SDRAM_BASE 0x00000000
-#ifdef CONFIG_FADS
-# define CFG_SDRAM_SIZE 0x00400000 /* 4 meg */
-#else /* !CONFIG_FADS */ /* old ADS */
-# define CFG_SDRAM_SIZE 0x00000000 /* NO SDRAM */
-#endif
-
-#define CFG_FLASH_BASE TEXT_BASE
-
-#define CFG_FLASH_SIZE ((uint)(8 * 1024 * 1024)) /* max 8Mbyte */
-
-#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
-#define CFG_MONITOR_BASE CFG_FLASH_BASE
-#define CFG_MALLOC_LEN (384 << 10) /* Reserve 384 kB for malloc() */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define CFG_MAX_FLASH_SECT 16 /* max number of sectors on one chip */
-
-#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
-#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
-
-#define CFG_ENV_IS_IN_FLASH 1
-#define CFG_ENV_OFFSET 0x00040000
-#define CFG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */
-
-#define CFG_ENV_SECT_SIZE 0x40000 /* see README - env sector total size */
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */
-#endif
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control 11-9
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
- */
-#if defined(CONFIG_WATCHDOG)
-#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
- SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP)
-#else
-#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
-#endif
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration 11-6
- *-----------------------------------------------------------------------
- * PCMCIA config., multi-function pin tri-state
- */
-#define CFG_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
-
-/*-----------------------------------------------------------------------
- * TBSCR - Time Base Status and Control 11-26
- *-----------------------------------------------------------------------
- * Clear Reference Interrupt Status, Timebase freezing enabled
- */
-#define CFG_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBE)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control 11-31
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
- */
-#define CFG_PISCR (PISCR_PS | PISCR_PITF)
-
-/*-----------------------------------------------------------------------
- * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30
- *-----------------------------------------------------------------------
- * set the PLL, the low-power modes and the reset control (15-29)
- */
-#define CFG_PLPRCR (((CFG_8XX_FACT-1) << PLPRCR_MF_SHIFT) | \
- PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
-
-/*-----------------------------------------------------------------------
- * SCCR - System Clock and reset Control Register 15-27
- *-----------------------------------------------------------------------
- * Set clock output, timebase and RTC source and divider,
- * power management and some other internal clocks
- */
-#define SCCR_MASK SCCR_EBDF11
-#define CFG_SCCR (SCCR_TBS|SCCR_COM00|SCCR_DFSYNC00|SCCR_DFBRG00|SCCR_DFNL000|SCCR_DFNH000|SCCR_DFLCD000|SCCR_DFALCD00)
-
- /*-----------------------------------------------------------------------
- *
- *-----------------------------------------------------------------------
- *
- */
-#define CFG_DER 0
-
-/* Because of the way the 860 starts up and assigns CS0 the
-* entire address space, we have to set the memory controller
-* differently. Normally, you write the option register
-* first, and then enable the chip select by writing the
-* base register. For CS0, you must write the base register
-* first, followed by the option register.
-*/
-
-/*
- * Init Memory Controller:
- *
- * BR0/1 and OR0/1 (FLASH)
- */
-/* the other CS:s are determined by looking at parameters in BCSRx */
-
-#define BCSR_ADDR ((uint) 0xFF010000)
-#define BCSR_SIZE ((uint)(64 * 1024))
+#define CONFIG_DRAM_50MHZ 1
+#define CONFIG_SDRAM_50MHZ 1
-#define CFG_PRELIM_OR_AM 0xFF800000 /* OR addr mask */
+#include "fads.h"
-/* FLASH timing: ACS = 10, TRLX = 1, CSNT = 1, SCY = 3, EHTR = 0 */
-#define CFG_OR_TIMING_FLASH (OR_CSNT_SAM | OR_ACS_DIV4 | OR_BI | OR_SCY_3_CLK | OR_TRLX)
+#define CFG_PLPRCR (((CFG_8XX_FACT-1) << PLPRCR_MF_SHIFT) | \
+ PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
#ifdef USE_REAL_FLASH_VALUES
/*
* These values fit our FADS860T ...
* The "default" behaviour with 1Mbyte initial doesn't work for us!
*/
+#undef CFG_OR0_PRELIM
+#undef CFG_BR0_PRELIM
#define CFG_OR0_PRELIM 0x0FFC00D34 /* Real values for the board */
#define CFG_BR0_PRELIM 0x02800001 /* Real values for the board */
-#else
-#define CFG_OR0_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH) /* 8 Mbyte until detected */
-#define CFG_BR0_PRELIM ((CFG_FLASH_BASE & BR_BA_MSK) | BR_V )
-#endif
-
-/* BCSRx - Board Control and Status Registers */
-#define CFG_OR1_PRELIM 0xffff8110 /* 64Kbyte address space */
-#define CFG_BR1_PRELIM ((BCSR_ADDR) | BR_V )
-
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
-
-
-/* values according to the manual */
-
-
-#define PCMCIA_MEM_ADDR ((uint)0xff020000)
-#define PCMCIA_MEM_SIZE ((uint)(64 * 1024))
-
-#define BCSR0 ((uint) (BCSR_ADDR + 0x00))
-#define BCSR1 ((uint) (BCSR_ADDR + 0x04))
-#define BCSR2 ((uint) (BCSR_ADDR + 0x08))
-#define BCSR3 ((uint) (BCSR_ADDR + 0x0c))
-#define BCSR4 ((uint) (BCSR_ADDR + 0x10))
-
-/* FADS bitvalues by Helmut Buchsbaum
- * see MPC8xxADS User's Manual for a proper description
- * of the following structures
- */
-
-#define BCSR0_ERB ((uint)0x80000000)
-#define BCSR0_IP ((uint)0x40000000)
-#define BCSR0_BDIS ((uint)0x10000000)
-#define BCSR0_BPS_MASK ((uint)0x0C000000)
-#define BCSR0_ISB_MASK ((uint)0x01800000)
-#define BCSR0_DBGC_MASK ((uint)0x00600000)
-#define BCSR0_DBPC_MASK ((uint)0x00180000)
-#define BCSR0_EBDF_MASK ((uint)0x00060000)
-
-#define BCSR1_FLASH_EN ((uint)0x80000000)
-#define BCSR1_DRAM_EN ((uint)0x40000000)
-#define BCSR1_ETHEN ((uint)0x20000000)
-#define BCSR1_IRDEN ((uint)0x10000000)
-#define BCSR1_FLASH_CFG_EN ((uint)0x08000000)
-#define BCSR1_CNT_REG_EN_PROTECT ((uint)0x04000000)
-#define BCSR1_BCSR_EN ((uint)0x02000000)
-#define BCSR1_RS232EN_1 ((uint)0x01000000)
-#define BCSR1_PCCEN ((uint)0x00800000)
-#define BCSR1_PCCVCC0 ((uint)0x00400000)
-#define BCSR1_PCCVPP_MASK ((uint)0x00300000)
-#define BCSR1_DRAM_HALF_WORD ((uint)0x00080000)
-#define BCSR1_RS232EN_2 ((uint)0x00040000)
-#define BCSR1_SDRAM_EN ((uint)0x00020000)
-#define BCSR1_PCCVCC1 ((uint)0x00010000)
-
-#define BCSR2_FLASH_PD_MASK ((uint)0xF0000000)
-#define BCSR2_DRAM_PD_MASK ((uint)0x07800000)
-#define BCSR2_DRAM_PD_SHIFT (23)
-#define BCSR2_EXTTOLI_MASK ((uint)0x00780000)
-#define BCSR2_DBREVNR_MASK ((uint)0x00030000)
-
-#define BCSR3_DBID_MASK ((ushort)0x3800)
-#define BCSR3_CNT_REG_EN_PROTECT ((ushort)0x0400)
-#define BCSR3_BREVNR0 ((ushort)0x0080)
-#define BCSR3_FLASH_PD_MASK ((ushort)0x0070)
-#define BCSR3_BREVN1 ((ushort)0x0008)
-#define BCSR3_BREVN2_MASK ((ushort)0x0003)
-
-#define BCSR4_ETHLOOP ((uint)0x80000000)
-#define BCSR4_TFPLDL ((uint)0x40000000)
-#define BCSR4_TPSQEL ((uint)0x20000000)
-#define BCSR4_SIGNAL_LAMP ((uint)0x10000000)
-#ifdef CONFIG_MPC823
-#define BCSR4_USB_EN ((uint)0x08000000)
-#endif /* CONFIG_MPC823 */
-#ifdef CONFIG_MPC860SAR
-#define BCSR4_UTOPIA_EN ((uint)0x08000000)
-#endif /* CONFIG_MPC860SAR */
-#ifdef CONFIG_MPC860T
-#define BCSR4_FETH_EN ((uint)0x08000000)
-#endif /* CONFIG_MPC860T */
-#ifdef CONFIG_MPC823
-#define BCSR4_USB_SPEED ((uint)0x04000000)
-#endif /* CONFIG_MPC823 */
-#ifdef CONFIG_MPC860T
-#define BCSR4_FETHCFG0 ((uint)0x04000000)
-#endif /* CONFIG_MPC860T */
-#ifdef CONFIG_MPC823
-#define BCSR4_VCCO ((uint)0x02000000)
-#endif /* CONFIG_MPC823 */
-#ifdef CONFIG_MPC860T
-#define BCSR4_FETHFDE ((uint)0x02000000)
-#endif /* CONFIG_MPC860T */
-#ifdef CONFIG_MPC823
-#define BCSR4_VIDEO_ON ((uint)0x00800000)
-#endif /* CONFIG_MPC823 */
-#ifdef CONFIG_MPC823
-#define BCSR4_VDO_EKT_CLK_EN ((uint)0x00400000)
-#endif /* CONFIG_MPC823 */
-#ifdef CONFIG_MPC860T
-#define BCSR4_FETHCFG1 ((uint)0x00400000)
-#endif /* CONFIG_MPC860T */
-#ifdef CONFIG_MPC823
-#define BCSR4_VIDEO_RST ((uint)0x00200000)
-#endif /* CONFIG_MPC823 */
-#ifdef CONFIG_MPC860T
-#define BCSR4_FETHRST ((uint)0x00200000)
-#endif /* CONFIG_MPC860T */
-#ifdef CONFIG_MPC823
-#define BCSR4_MODEM_EN ((uint)0x00100000)
-#endif /* CONFIG_MPC823 */
-#ifdef CONFIG_MPC823
-#define BCSR4_DATA_VOICE ((uint)0x00080000)
-#endif /* CONFIG_MPC823 */
-#ifdef CONFIG_MPC850
-#define BCSR4_DATA_VOICE ((uint)0x00080000)
-#endif /* CONFIG_MPC850 */
-
-#define CONFIG_DRAM_50MHZ 1
-#define CONFIG_SDRAM_50MHZ 1
-
-/* We don't use the 8259.
-*/
-#define NR_8259_INTS 0
-
-/* Machine type
-*/
-#define _MACH_8xx (_MACH_fads)
-
-#define CONFIG_DISK_SPINUP_TIME 1000000
-
-
-/* PCMCIA configuration */
-
-#ifdef CONFIG_MPC860
-#define PCMCIA_SLOT_A 1
#endif
-/*#define CFG_PCMCIA_MEM_SIZE ( 64 << 20) */
-#define CFG_PCMCIA_MEM_ADDR (0x50000000)
-#define CFG_PCMCIA_MEM_SIZE ( 64 << 20 )
-#define CFG_PCMCIA_DMA_ADDR (0x54000000)
-#define CFG_PCMCIA_DMA_SIZE ( 64 << 20 )
-#define CFG_PCMCIA_ATTRB_ADDR (0x58000000)
-#define CFG_PCMCIA_ATTRB_SIZE ( 64 << 20 )
-#define CFG_PCMCIA_IO_ADDR (0x5C000000)
-#define CFG_PCMCIA_IO_SIZE ( 64 << 20 )
-/* we have 8 windows, we take everything up to 60000000 */
-
-#define CFG_ATA_IDE0_OFFSET 0x0000
-
-#define CFG_ATA_BASE_ADDR CFG_PCMCIA_MEM_ADDR
-
-/* Offset for data I/O */
-#define CFG_ATA_DATA_OFFSET (CFG_PCMCIA_MEM_SIZE + 0x320)
-/* Offset for normal register accesses */
-#define CFG_ATA_REG_OFFSET (2 * CFG_PCMCIA_MEM_SIZE + 0x320)
-/* Offset for alternate registers */
-#define CFG_ATA_ALT_OFFSET 0x0000
-/*#define CFG_ATA_ALT_OFFSET 0x0100 */
+#define CFG_DAUGHTERBOARD /* FADS has processor-specfic daughterboard */
#endif /* __CONFIG_H */
diff --git a/include/configs/MPC86xADS.h b/include/configs/MPC86xADS.h
index 1eac6ef..a6e2606 100644
--- a/include/configs/MPC86xADS.h
+++ b/include/configs/MPC86xADS.h
@@ -3,24 +3,12 @@
* the Motorola MPC8xxADS board. Copied from the FADS config.
*
* Copyright (c) 1998 Dan Malek (dmalek@jlc.net)
+ *
+ * Modified by, Yuli Barcohen, Arabella Software Ltd., yuli@arabellasw.com
+ *
+ * Values common to all FADS family boards are in board/fads/fads.h
*/
-/*
- * 1999-nov-26: The FADS is using the following physical memorymap:
- *
- * ff020000 -> ff02ffff : pcmcia
- * ff010000 -> ff01ffff : BCSR connected to CS1
- * ff000000 -> ff00ffff : IMAP internal in the cpu
- * fe000000 -> fennnnnn : flash connected to CS0
- * 00000000 -> nnnnnnnn : sdram connected to CS4
- */
-
-/* ------------------------------------------------------------------------- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
#ifndef __CONFIG_H
#define __CONFIG_H
@@ -33,7 +21,7 @@
#define CONFIG_MPC86xADS 1 /* new ADS */
#define CONFIG_FADS 1 /* We are FADS compatible (more or less) */
-/* new 86xADS only - pick one of these */
+/* New MPC86xADS - pick one of these */
#define CONFIG_MPC866T 1
#undef CONFIG_MPC866P
#undef CONFIG_MPC859T
@@ -44,374 +32,20 @@
#undef CONFIG_8xx_CONS_SMC2
#undef CONFIG_8xx_CONS_NONE
#define CONFIG_BAUDRATE 38400
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#ifdef CONFIG_MPC86xADS
# define CFG_8XX_FACT 5 /* Multiply by 5 */
# define CFG_8XX_XIN 10000000 /* 10 MHz in */
-#else /* ! CONFIG_MPC86xADS */
-# if 0 /* old FADS */
-# define CFG_8XX_FACT 12 /* Multiply by 12 */
-# define CFG_8XX_XIN 4000000 /* 4 MHz in */
-# else /* new FADS */
-# define CFG_8XX_FACT 10 /* Multiply by 10 */
-# define CFG_8XX_XIN 5000000 /* 5 MHz in */
-# endif
-#endif /* ! CONFIG_MPC86xADS */
-
-#define MPC8XX_HZ ((CFG_8XX_XIN) * (CFG_8XX_FACT))
-
-/* should ALWAYS define this, measure_gclk in speed.c is unreliable */
-/* in general, we always know this for FADS+new ADS anyway */
-#define CONFIG_8xx_GCLK_FREQ MPC8XX_HZ
-
-#if 1
-#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
-#else
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-#endif
-
-#undef CONFIG_BOOTARGS
-#define CONFIG_BOOTCOMMAND \
- "dhcp;" \
- "setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) " \
- "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off;" \
- "bootm"
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-/* ATA / IDE and partition support */
-#define CONFIG_MAC_PARTITION 1
-#define CONFIG_DOS_PARTITION 1
-#define CONFIG_ISO_PARTITION 1
-#undef CONFIG_ATAPI
-#define CONFIG_IDE_8xx_PCCARD 1 /* Use IDE with PC Card Adapter */
-#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
-#undef CONFIG_IDE_LED /* LED for ide not supported */
-#undef CONFIG_IDE_RESET /* reset for ide not supported */
-
-/*
- * New MPC86xADS provides two Ethernet connectivity options:
- * 10Mbit/s on SCC1 and 100Mbit/s on FEC. All new PQ1 chips
- * has got FEC so FEC is the default.
- */
-#undef CONFIG_SCC1_ENET /* disable SCC1 ethernet */
-#define CONFIG_FEC_ENET 1 /* use FEC ethernet */
-#ifdef CONFIG_FEC_ENET
-#define CFG_DISCOVER_PHY
-#endif
-#if defined(CONFIG_SCC1_ENET) && defined(CONFIG_FEC_ENET)
-#error Both CONFIG_SCC1_ENET and CONFIG_FEC_ENET configured
-#endif
-
-#define CONFIG_COMMANDS (CONFIG_CMD_DFL \
- | CFG_CMD_DHCP \
- | CFG_CMD_IMMAP \
- | CFG_CMD_MII \
- | CFG_CMD_PING \
- )
-
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
-
-/*
- * Miscellaneous configurable options
- */
-#undef CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=>" /* Monitor Command Prompt */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-
-#define CFG_LOAD_ADDR 0x00100000
-
-#define CFG_HZ 1000 /* decr freq: 1 ms ticks */
-
-#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-/*-----------------------------------------------------------------------
- * Internal Memory Mapped Register
- */
-#define CFG_IMMR 0xFF000000
-#define CFG_IMMR_SIZE ((uint)(64 * 1024))
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CFG_INIT_RAM_ADDR CFG_IMMR
-#define CFG_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */
-#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */
-#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CFG_SDRAM_BASE _must_ start at 0
- */
-#define CFG_SDRAM_BASE 0x00000000
-#if defined(CONFIG_MPC86xADS) /* new ADS */
-#define CFG_SDRAM_SIZE 0x00800000 /* 8 meg */
-#elif defined(CONFIG_FADS) /* old/new FADS */
-#define CFG_SDRAM_SIZE 0x00400000 /* 4 meg */
-#else /* old ADS */
-#define CFG_SDRAM_SIZE 0x00000000 /* No SDRAM */
-#endif
-
-#define CFG_MEMTEST_START 0x0100000 /* memtest works on */
-#if (CFG_SDRAM_SIZE)
-#define CFG_MEMTEST_END CFG_SDRAM_SIZE /* 1 ... SDRAM_SIZE */
-#else
-#define CFG_MEMTEST_END 0x0400000 /* 1 ... 4 MB in DRAM */
-#endif /* CFG_SDRAM_SIZE */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define CFG_FLASH_BASE TEXT_BASE
-#define CFG_FLASH_SIZE ((uint)(8 * 1024 * 1024)) /* max 8Mbyte */
-
-#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define CFG_MAX_FLASH_SECT 16 /* max number of sectors on one chip */
-
-#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
-#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
-
-#define CFG_ENV_IS_IN_FLASH 1
-#define CFG_ENV_SECT_SIZE 0x40000 /* see README - env sector total size */
-#define CFG_ENV_OFFSET CFG_ENV_SECT_SIZE
-#define CFG_ENV_SIZE 0x4000 /* Total Size of Environment */
-
-#define CFG_MONITOR_BASE CFG_FLASH_BASE
-#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 KB for monitor */
-#define CFG_MALLOC_LEN (384 << 10) /* Reserve 384 kB for malloc() */
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */
-#endif
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control 11-9
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
- */
-#if defined(CONFIG_WATCHDOG)
-#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
- SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP)
-#else
-#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
-#endif
+#define CONFIG_DRAM_50MHZ 1
+#define CONFIG_SDRAM_50MHZ 1
/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration 11-6
+ * PLPRCR - PLL, Low-Power, and Reset Control Register 14-22
*-----------------------------------------------------------------------
- * PCMCIA config., multi-function pin tri-state
+ * set the PLL, the low-power modes and the reset control
*/
-#define CFG_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
-
-/*-----------------------------------------------------------------------
- * TBSCR - Time Base Status and Control 11-26
- *-----------------------------------------------------------------------
- * Clear Reference Interrupt Status, Timebase freezing enabled
- */
-#define CFG_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBE)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control 11-31
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
- */
-#define CFG_PISCR (PISCR_PS | PISCR_PITF)
-
-/*-----------------------------------------------------------------------
- * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30
- *-----------------------------------------------------------------------
- * set the PLL, the low-power modes and the reset control (15-29)
- */
-#define CFG_PLPRCR ((CFG_8XX_FACT << PLPRCR_MFI_SHIFT) | \
- PLPRCR_SPLSS | PLPRCR_TEXPS)
-
-/*-----------------------------------------------------------------------
- * SCCR - System Clock and reset Control Register 15-27
- *-----------------------------------------------------------------------
- * Set clock output, timebase and RTC source and divider,
- * power management and some other internal clocks
- */
-#define SCCR_MASK SCCR_EBDF11
-#define CFG_SCCR (SCCR_TBS|SCCR_COM00|SCCR_DFSYNC00|SCCR_DFBRG00|SCCR_DFNL000|SCCR_DFNH000|SCCR_DFLCD000|SCCR_DFALCD00)
-
- /*-----------------------------------------------------------------------
- *
- *-----------------------------------------------------------------------
- *
- */
-#define CFG_DER 0
-
-/* Because of the way the 860 starts up and assigns CS0 the
-* entire address space, we have to set the memory controller
-* differently. Normally, you write the option register
-* first, and then enable the chip select by writing the
-* base register. For CS0, you must write the base register
-* first, followed by the option register.
-*/
-
-/*
- * Init Memory Controller:
- *
- * BR0/OR0 (Flash)
- * BR1/OR1 (BCSR)
- */
-/* the other CS:s are determined by looking at parameters in BCSRx */
-
-#define BCSR_ADDR ((uint) 0xFF010000)
-#define BCSR_SIZE ((uint)(64 * 1024))
-
-#define CFG_PRELIM_OR_AM 0xFF800000 /* OR addr mask */
-
-/* FLASH timing: ACS = 10, TRLX = 1, CSNT = 1, SCY = 3, EHTR = 0 */
-#define CFG_OR_TIMING_FLASH (OR_CSNT_SAM | OR_ACS_DIV4 | OR_BI | OR_SCY_3_CLK | OR_TRLX)
-
-#define CFG_OR0_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH) /* 8 Mbyte until detected */
-#define CFG_BR0_PRELIM ((CFG_FLASH_BASE & BR_BA_MSK) | BR_V )
-
-/* BCSRx - Board Control and Status Registers */
-#define CFG_OR1_PRELIM 0xffff8110 /* 64Kbyte address space */
-#define CFG_BR1_PRELIM ((BCSR_ADDR) | BR_V )
-
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
-
-/* values according to the manual */
-
-#define PCMCIA_MEM_ADDR ((uint)0xff020000)
-#define PCMCIA_MEM_SIZE ((uint)(64 * 1024))
-
-#define BCSR0 ((uint) (BCSR_ADDR + 0x00))
-#define BCSR1 ((uint) (BCSR_ADDR + 0x04))
-#define BCSR2 ((uint) (BCSR_ADDR + 0x08))
-#define BCSR3 ((uint) (BCSR_ADDR + 0x0c))
-#define BCSR4 ((uint) (BCSR_ADDR + 0x10))
-
-/* FADS bitvalues by Helmut Buchsbaum
- * see MPC8xxADS User's Manual for a proper description
- * of the following structures
- */
-
-#define BCSR0_ERB ((uint)0x80000000)
-#define BCSR0_IP ((uint)0x40000000)
-#define BCSR0_BDIS ((uint)0x10000000)
-#define BCSR0_BPS_MASK ((uint)0x0C000000)
-#define BCSR0_ISB_MASK ((uint)0x01800000)
-#define BCSR0_DBGC_MASK ((uint)0x00600000)
-#define BCSR0_DBPC_MASK ((uint)0x00180000)
-#define BCSR0_EBDF_MASK ((uint)0x00060000)
-
-#define BCSR1_FLASH_EN ((uint)0x80000000)
-#define BCSR1_DRAM_EN ((uint)0x40000000)
-#define BCSR1_ETHEN ((uint)0x20000000)
-#define BCSR1_IRDEN ((uint)0x10000000)
-#define BCSR1_FLASH_CFG_EN ((uint)0x08000000)
-#define BCSR1_CNT_REG_EN_PROTECT ((uint)0x04000000)
-#define BCSR1_BCSR_EN ((uint)0x02000000)
-#define BCSR1_RS232EN_1 ((uint)0x01000000)
-#define BCSR1_PCCEN ((uint)0x00800000)
-#define BCSR1_PCCVCC0 ((uint)0x00400000)
-#define BCSR1_PCCVPP_MASK ((uint)0x00300000)
-#define BCSR1_DRAM_HALF_WORD ((uint)0x00080000)
-#define BCSR1_RS232EN_2 ((uint)0x00040000)
-#define BCSR1_SDRAM_EN ((uint)0x00020000)
-#define BCSR1_PCCVCC1 ((uint)0x00010000)
-
-#define BCSR2_FLASH_PD_MASK ((uint)0xF0000000)
-#define BCSR2_DRAM_PD_MASK ((uint)0x07800000)
-#define BCSR2_DRAM_PD_SHIFT (23)
-#define BCSR2_EXTTOLI_MASK ((uint)0x00780000)
-#define BCSR2_DBREVNR_MASK ((uint)0x00030000)
-
-#define BCSR3_DBID_MASK ((ushort)0x3800)
-#define BCSR3_CNT_REG_EN_PROTECT ((ushort)0x0400)
-#define BCSR3_BREVNR0 ((ushort)0x0080)
-#define BCSR3_FLASH_PD_MASK ((ushort)0x0070)
-#define BCSR3_BREVN1 ((ushort)0x0008)
-#define BCSR3_BREVN2_MASK ((ushort)0x0003)
-
-#define BCSR4_ETHLOOP ((uint)0x80000000)
-#define BCSR4_TFPLDL ((uint)0x40000000)
-#define BCSR4_TPSQEL ((uint)0x20000000)
-#define BCSR4_SIGNAL_LAMP ((uint)0x10000000)
-#define BCSR4_FETH_EN ((uint)0x08000000)
-#define BCSR4_FETHCFG0 ((uint)0x04000000)
-#define BCSR4_FETHFDE ((uint)0x02000000)
-#define BCSR4_FETHCFG1 ((uint)0x00400000)
-#define BCSR4_FETHRST ((uint)0x00200000)
-
-#define CONFIG_DRAM_50MHZ 1
-#define CONFIG_SDRAM_50MHZ 1
-
-/* We don't use the 8259.
-*/
-#define NR_8259_INTS 0
-
-/* Machine type
-*/
-#define _MACH_8xx (_MACH_fads)
-
-#define CONFIG_DISK_SPINUP_TIME 1000000
-
-
-/* PCMCIA configuration */
-
-#ifdef CONFIG_MPC860
-#define PCMCIA_SLOT_A 1
-#endif
-
-#define CFG_PCMCIA_MEM_ADDR (0x50000000)
-#define CFG_PCMCIA_MEM_SIZE ( 64 << 20 )
-#define CFG_PCMCIA_DMA_ADDR (0x54000000)
-#define CFG_PCMCIA_DMA_SIZE ( 64 << 20 )
-#define CFG_PCMCIA_ATTRB_ADDR (0x58000000)
-#define CFG_PCMCIA_ATTRB_SIZE ( 64 << 20 )
-#define CFG_PCMCIA_IO_ADDR (0x5C000000)
-#define CFG_PCMCIA_IO_SIZE ( 64 << 20 )
-/* we have 8 windows, we take everything up to 60000000 */
-
-#define CFG_ATA_IDE0_OFFSET 0x0000
-
-#define CFG_ATA_BASE_ADDR CFG_PCMCIA_MEM_ADDR
-
-/* Offset for data I/O */
-#define CFG_ATA_DATA_OFFSET (CFG_PCMCIA_MEM_SIZE + 0x320)
-/* Offset for normal register accesses */
-#define CFG_ATA_REG_OFFSET (2 * CFG_PCMCIA_MEM_SIZE + 0x320)
-/* Offset for alternate registers */
-#define CFG_ATA_ALT_OFFSET 0x0000
-/*#define CFG_ATA_ALT_OFFSET 0x0100 */
+#define CFG_PLPRCR ((CFG_8XX_FACT << PLPRCR_MFI_SHIFT) | PLPRCR_TEXPS)
+#include "fads.h"
#endif /* __CONFIG_H */
diff --git a/include/configs/PPChameleonEVB.h b/include/configs/PPChameleonEVB.h
index 78ae6ba..50e8a15 100644
--- a/include/configs/PPChameleonEVB.h
+++ b/include/configs/PPChameleonEVB.h
@@ -521,7 +521,7 @@
#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
#define BOOTFLAG_WARM 0x02 /* Software reboot */
-#if 1 /* test-only */
+
#define CONFIG_NO_SERIAL_EEPROM
/*#undef CONFIG_NO_SERIAL_EEPROM*/
/*--------------------------------------------------------------------*/
@@ -651,16 +651,11 @@
#define PLL_PCIDIV_3 0x00000002
#define PLL_PCIDIV_4 0x00000003
-/*
-!-----------------------------------------------------------------------
-! PLL settings for 266MHz CPU, 133MHz PLB/SDRAM, 66MHz EBC, 33MHz PCI,
-! assuming a 33.3MHz input clock to the 405EP.
-!-----------------------------------------------------------------------
-*/
-#define PLLMR0_133_66_66_33 (PLL_CPUDIV_1 | PLL_PLBDIV_1 | \
+/* CPU - PLB/SDRAM - EBC - OPB - PCI (assuming a 33.3MHz input clock to the 405EP) */
+#define PLLMR0_133_133_33_66_33 (PLL_CPUDIV_1 | PLL_PLBDIV_1 | \
PLL_OPBDIV_2 | PLL_EXTBUSDIV_4 | \
PLL_MALDIV_1 | PLL_PCIDIV_4)
-#define PLLMR1_133_66_66_33 (PLL_FBKDIV_4 | \
+#define PLLMR1_133_133_33_66_33 (PLL_FBKDIV_4 | \
PLL_FWDDIVA_6 | PLL_FWDDIVB_6 | \
PLL_TUNE_15_M_40 | PLL_TUNE_VCO_LOW)
#define PLLMR0_200_100_50_33 (PLL_CPUDIV_1 | PLL_PLBDIV_2 | \
@@ -669,27 +664,35 @@
#define PLLMR1_200_100_50_33 (PLL_FBKDIV_6 | \
PLL_FWDDIVA_4 | PLL_FWDDIVB_4 | \
PLL_TUNE_15_M_40 | PLL_TUNE_VCO_LOW)
-#define PLLMR0_266_133_66_33 (PLL_CPUDIV_1 | PLL_PLBDIV_2 | \
+#define PLLMR0_266_133_33_66_33 (PLL_CPUDIV_1 | PLL_PLBDIV_2 | \
PLL_OPBDIV_2 | PLL_EXTBUSDIV_4 | \
PLL_MALDIV_1 | PLL_PCIDIV_4)
-#define PLLMR1_266_133_66_33 (PLL_FBKDIV_8 | \
+#define PLLMR1_266_133_33_66_33 (PLL_FBKDIV_8 | \
PLL_FWDDIVA_3 | PLL_FWDDIVB_3 | \
PLL_TUNE_15_M_40 | PLL_TUNE_VCO_LOW)
-#if 0 /* test-only */
-#define PLLMR0_DEFAULT PLLMR0_266_133_66_33
-#define PLLMR1_DEFAULT PLLMR1_266_133_66_33
-#endif
-#if 0 /* test-only */
-#define PLLMR0_DEFAULT PLLMR0_200_100_50_33
-#define PLLMR1_DEFAULT PLLMR1_200_100_50_33
-#endif
-#if 1 /* test-only */
-#define PLLMR0_DEFAULT PLLMR0_133_66_66_33
-#define PLLMR1_DEFAULT PLLMR1_133_66_66_33
-#endif
+#define PLLMR0_333_111_37_55_55 (PLL_CPUDIV_1 | PLL_PLBDIV_3 | \
+ PLL_OPBDIV_2 | PLL_EXTBUSDIV_3 | \
+ PLL_MALDIV_1 | PLL_PCIDIV_2)
+#define PLLMR1_333_111_37_55_55 (PLL_FBKDIV_10 | \
+ PLL_FWDDIVA_3 | PLL_FWDDIVB_3 | \
+ PLL_TUNE_15_M_40 | PLL_TUNE_VCO_HI)
+
+#if (CONFIG_PPCHAMELEON_MODULE_MODEL == CONFIG_PPCHAMELEON_MODULE_HI)
+/* Model HI */
+#define PLLMR0_DEFAULT PLLMR0_333_111_37_55_55
+#define PLLMR1_DEFAULT PLLMR1_333_111_37_55_55
+/* Model ME */
+#elif (CONFIG_PPCHAMELEON_MODULE_MODEL == CONFIG_PPCHAMELEON_MODULE_ME)
+#define PLLMR0_DEFAULT PLLMR0_266_133_33_66_33
+#define PLLMR1_DEFAULT PLLMR1_266_133_33_66_33
+#else
+/* Model BA (default) */
+#define PLLMR0_DEFAULT PLLMR0_133_133_33_66_33
+#define PLLMR1_DEFAULT PLLMR1_133_133_33_66_33
#endif
-#endif
+
+#endif /* CONFIG_NO_SERIAL_EEPROM */
#define CFG_OPB_FREQ 50000000