diff options
Diffstat (limited to 'include')
-rw-r--r-- | include/configs/sc3.h | 549 |
1 files changed, 0 insertions, 549 deletions
diff --git a/include/configs/sc3.h b/include/configs/sc3.h deleted file mode 100644 index 14e033d..0000000 --- a/include/configs/sc3.h +++ /dev/null @@ -1,549 +0,0 @@ -/* - * (C) Copyright 2007 - * Heiko Schocher, DENX Software Engineering, <hs@denx.de>. - * - * From: - * (C) Copyright 2003 - * Juergen Beisert, EuroDesign embedded technologies, jbeisert@eurodsn.de - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -#undef USE_VGA_GRAPHICS - -/* Memory Map - * 0x00000000 .... 0x03FFFFFF -> RAM (up to 128MiB) - * 0x74000000 .... 0x740FFFFF -> CS#6 - * 0x74100000 .... 0x741FFFFF -> CS#7 - * 0x74200000 .... 0x742FFFFF -> CS4# if no internal USB - * 0x74300000 .... 0x743FFFFF -> CS5# if no boosted IDE - * 0x77C00000 .... 0x77CFFFFF -> CS4# USB HC (1 MiB) - * 0x77D00000 .... 0x77DFFFFF -> CS1# NAND-Flash (1 MiB) - * 0x78000000 .... 0x78FFFFFF -> CS2# ISA-Bus Speicherzugriff (16 MiB) - * 0x79000000 .... 0x7900FFFF -> CS2# ISA-Bus IO-Zugriff (16 MiB, mapped: 64kiB) - * 0x79010000 .... 0x79FFFFFF -> CS2# ISA-Bus IO-Zugriff (mirrored) - * 0x7A000000 .... 0x7A0FFFFF -> CS5# IDE emulation (1MiB) - * - * 0x80000000 .... 0x9FFFFFFF -> PCI-Bus Speicherzugriff (512MiB, mapped: 1:1) - * 0xA0000000 .... 0xBFFFFFFF -> PCI-Bus Speicherzugriff (512MiB, mapped: 0x00000000...0x1FFFFFFF) - * 0xE8000000 .... 0xE800FFFF -> PCI-Bus IO-Zugriff (64kiB, translated to PCI: 0x0000...0xFFFF) - * 0xE8800000 .... 0xEBFFFFFF -> PCI-Bus IO-Zugriff (56MiB, translated to PCI: 0x00800000...0x3FFFFFF) - * 0xEED00000 .... 0xEED00003 -> PCI-Bus - * 0xEF400000 .... 0xEF40003F -> PCI-Bus Local Configuration Registers - * 0xEF40003F .... 0xEF5FFFFF -> reserved - * 0xEF600000 .... 0xEFFFFFFF -> 405GP internal Devices (10 MiB) - * 0xF0000000 .... 0xF01FFFFF -> Flash-ROM (2 MiB) - * 0xF0200000 .... 0xF7FFFFFF -> free for flash devices - * 0xF8000000 .... 0xF8000FFF -> OnChipMemory (4kiB) - * 0xF8001000 .... 0xFFDFFFFF -> free for flash devices - * 0xFFE00000 .... 0xFFFFFFFF -> BOOT-ROM (2 MiB) - */ - -#define CONFIG_SC3 1 -#define CONFIG_405GP 1 - -#define CONFIG_SYS_TEXT_BASE 0xFFFA0000 - -#define CONFIG_BOARD_EARLY_INIT_F 1 -#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r() */ - -/* - * Define IDE_USES_ISA_EMULATION for slower IDE access in the ISA-IO address range - * If undefined, IDE access uses a seperat emulation with higher access speed. - * Consider to inform your Linux IDE driver about the different addresses! - * IDE_USES_ISA_EMULATION is only used if you define CONFIG_CMD_IDE! - */ -#define IDE_USES_ISA_EMULATION - -/*----------------------------------------------------------------------- - * Serial Port - *----------------------------------------------------------------------*/ -#define CONFIG_CONS_INDEX 1 /* Use UART0 */ -#define CONFIG_SYS_NS16550 -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE 1 -#define CONFIG_SYS_NS16550_CLK get_serial_clock() - -/* - * define CONFIG_SYS_CLK_FREQ to your base crystal clock in Hz - */ -#define CONFIG_SYS_CLK_FREQ 33333333 - -/* - * define CONFIG_BAUDRATE to the baudrate value you want to use as default - */ -#define CONFIG_BAUDRATE 115200 -#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */ - -#define CONFIG_PREBOOT "echo;" \ - "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ - "echo" - -#undef CONFIG_BOOTARGS - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "nand_args=setenv bootargs root=/dev/mtdblock5 rw" \ - "rootfstype=jffs2\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "addcons=setenv bootargs ${bootargs} " \ - "console=ttyS0,${baudrate}\0" \ - "flash_nfs=run nfsargs addip addcons;" \ - "bootm ${kernel_addr}\0" \ - "flash_nand=run nand_args addip addcons;bootm ${kernel_addr}\0" \ - "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addcons;" \ - "bootm\0" \ - "rootpath=/opt/eldk/ppc_4xx\0" \ - "bootfile=/tftpboot/sc3/uImage\0" \ - "u-boot=/tftpboot/sc3/u-boot.bin\0" \ - "setup=tftp 200000 /tftpboot/sc3/setup.img;source 200000\0" \ - "kernel_addr=FFE08000\0" \ - "" -#undef CONFIG_BOOTCOMMAND - -#define CONFIG_SILENT_CONSOLE 1 /* enable silent startup */ -#define CONFIG_SYS_DEVICE_NULLDEV 1 /* include nulldev device */ - -#if 1 /* feel free to disable for development */ -#define CONFIG_AUTOBOOT_KEYED /* Enable password protection */ -#define CONFIG_AUTOBOOT_PROMPT \ - "\nSC3 - booting... stop with ENTER\n" -#define CONFIG_AUTOBOOT_DELAY_STR "\r" /* 1st "password" */ -#define CONFIG_AUTOBOOT_DELAY_STR2 "\n" /* 1st "password" */ -#endif - -/* - * define CONFIG_BOOTCOMMAND to the autoboot commands. They will running after - * the CONFIG_BOOTDELAY delay to boot your machine - */ -#define CONFIG_BOOTCOMMAND "bootp;dcache on;bootm" - -/* - * define CONFIG_BOOTARGS to the default kernel parameters. They will used if you don't - * set different values at the u-boot prompt - */ -#ifdef USE_VGA_GRAPHICS - #define CONFIG_BOOTARGS "root=/dev/nfs rw ip=bootp nfsroot=/tftpboot/solidcard3re" -#else - #define CONFIG_BOOTARGS "console=ttyS0,115200 root=/dev/nfs rw ip=bootp" -#endif -/* - * Is the USB host controller assembled? If yes define CONFIG_ISP1161_PRESENT - * This reserves memory bank #4 for this purpose - */ -#undef CONFIG_ISP1161_PRESENT - -#undef CONFIG_LOADS_ECHO /* no echo on for serial download */ -#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ - -/* #define CONFIG_EEPRO100_SROM_WRITE */ -/* #define CONFIG_SHOW_MAC */ -#define CONFIG_EEPRO100 - -#define CONFIG_PPC4xx_EMAC -#define CONFIG_MII 1 /* add 405GP MII PHY management */ -#define CONFIG_PHY_ADDR 1 /* the connected Phy defaults to address 1 */ - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - - -#define CONFIG_CMD_CACHE -#define CONFIG_CMD_DATE -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_ELF -#define CONFIG_CMD_I2C -#define CONFIG_CMD_IDE -#define CONFIG_CMD_IRQ -#define CONFIG_CMD_JFFS2 -#define CONFIG_CMD_MII -#define CONFIG_CMD_NAND -#define CONFIG_CMD_NET -#define CONFIG_CMD_PCI -#define CONFIG_CMD_PING -#define CONFIG_CMD_SOURCE - - -#undef CONFIG_WATCHDOG /* watchdog disabled */ - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP 1 /* undef to save memory */ -#define CONFIG_SYS_PROMPT "SC3> " /* Monitor Command Prompt */ -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ - -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ - -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ - -/* - * If CONFIG_SYS_EXT_SERIAL_CLOCK, then the UART divisor is 1. - * If CONFIG_SYS_405_UART_ERRATA_59, then UART divisor is 31. - * Otherwise, UART divisor is determined by CPU Clock and CONFIG_SYS_BASE_BAUD value. - * The Linux BASE_BAUD define should match this configuration. - * baseBaud = cpuClock/(uartDivisor*16) - * If CONFIG_SYS_405_UART_ERRATA_59 and 200MHz CPU clock, - * set Linux BASE_BAUD to 403200. - * - * Consider the OPB clock! If it get lower the BASE_BAUD must be lower to - * (see 405GP datasheet for descritpion) - */ -#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* external serial clock */ -#undef CONFIG_SYS_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */ -#define CONFIG_SYS_BASE_BAUD 921600 /* internal clock */ - -/* The following table includes the supported baudrates */ -#define CONFIG_SYS_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400} - -#define CONFIG_SYS_LOAD_ADDR 0x1000000 /* default load address */ -#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */ - -/*----------------------------------------------------------------------- - * IIC stuff - *----------------------------------------------------------------------- - */ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_PPC4XX -#define CONFIG_SYS_I2C_PPC4XX_CH0 - -#define I2C_INIT -#define I2C_ACTIVE 0 -#define I2C_TRISTATE 0 - -#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 100000 -#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F /* mask valid bits */ - -#define CONFIG_RTC_DS1337 -#define CONFIG_SYS_I2C_RTC_ADDR 0x68 - -/*----------------------------------------------------------------------- - * PCI stuff - *----------------------------------------------------------------------- - */ -#define PCI_HOST_ADAPTER 0 /* configure ar pci adapter */ -#define PCI_HOST_FORCE 1 /* configure as pci host */ -#define PCI_HOST_AUTO 2 /* detected via arbiter enable */ - -#define CONFIG_PCI /* include pci support */ -#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */ -#define CONFIG_PCI_HOST PCI_HOST_FORCE /* select pci host function */ -#define CONFIG_PCI_PNP /* do pci plug-and-play */ - /* resource configuration */ - -/* If you want to see, whats connected to your PCI bus */ -/* #define CONFIG_PCI_SCAN_SHOW */ - -#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x0000 /* PCI Vendor ID: to-do!!! */ -#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0000 /* PCI Device ID: to-do!!! */ -#define CONFIG_SYS_PCI_PTM1LA 0x00000000 /* point to sdram */ -#define CONFIG_SYS_PCI_PTM1MS 0x80000001 /* 2GB, enable hard-wired to 1 */ -#define CONFIG_SYS_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */ -#define CONFIG_SYS_PCI_PTM2LA 0x00000000 /* disabled */ -#define CONFIG_SYS_PCI_PTM2MS 0x00000000 /* disabled */ -#define CONFIG_SYS_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */ - -/*----------------------------------------------------------------------- - * External peripheral base address - *----------------------------------------------------------------------- - */ -#if !defined(CONFIG_CMD_IDE) - -#undef CONFIG_IDE_LED /* no led for ide supported */ -#undef CONFIG_IDE_RESET /* no reset for ide supported */ - -/*----------------------------------------------------------------------- - * IDE/ATA stuff - *----------------------------------------------------------------------- - */ -#else -#define CONFIG_START_IDE 1 /* check, if use IDE */ - -#undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */ -#undef CONFIG_IDE_LED /* no led for ide supported */ -#undef CONFIG_IDE_RESET /* no reset for ide supported */ - -#define CONFIG_ATAPI -#define CONFIG_DOS_PARTITION -#define CONFIG_SYS_IDE_MAXDEVICE (CONFIG_SYS_IDE_MAXBUS*1) /* max. 1 drives per IDE bus */ - -#ifndef IDE_USES_ISA_EMULATION - -/* New and faster access */ -#define CONFIG_SYS_ATA_BASE_ADDR 0x7A000000 /* start of ISA IO emulation */ - -/* How many IDE busses are available */ -#define CONFIG_SYS_IDE_MAXBUS 1 - -/* What IDE ports are available */ -#define CONFIG_SYS_ATA_IDE0_OFFSET 0x000 /* first is available */ -#undef CONFIG_SYS_ATA_IDE1_OFFSET /* second not available */ - -/* access to the data port is calculated: - CONFIG_SYS_ATA_BASE_ADDR + CONFIG_SYS_ATA_IDE0_OFFSET + CONFIG_SYS_ATA_DATA_OFFSET + 0 */ -#define CONFIG_SYS_ATA_DATA_OFFSET 0x0000 /* Offset for data I/O */ - -/* access to the registers is calculated: - CONFIG_SYS_ATA_BASE_ADDR + CONFIG_SYS_ATA_IDE0_OFFSET + CONFIG_SYS_ATA_REG_OFFSET + [1..7] */ -#define CONFIG_SYS_ATA_REG_OFFSET 0x0000 /* Offset for normal register accesses */ - -/* access to the alternate register is calculated: - CONFIG_SYS_ATA_BASE_ADDR + CONFIG_SYS_ATA_IDE0_OFFSET + CONFIG_SYS_ATA_ALT_OFFSET + 6 */ -#define CONFIG_SYS_ATA_ALT_OFFSET 0x008 /* Offset for alternate registers */ - -#else /* IDE_USES_ISA_EMULATION */ - -#define CONFIG_SYS_ATA_BASE_ADDR 0x79000000 /* start of ISA IO emulation */ - -/* How many IDE busses are available */ -#define CONFIG_SYS_IDE_MAXBUS 1 - -/* What IDE ports are available */ -#define CONFIG_SYS_ATA_IDE0_OFFSET 0x01F0 /* first is available */ -#undef CONFIG_SYS_ATA_IDE1_OFFSET /* second not available */ - -/* access to the data port is calculated: - CONFIG_SYS_ATA_BASE_ADDR + CONFIG_SYS_ATA_IDE0_OFFSET + CONFIG_SYS_ATA_DATA_OFFSET + 0 */ -#define CONFIG_SYS_ATA_DATA_OFFSET 0x0000 /* Offset for data I/O */ - -/* access to the registers is calculated: - CONFIG_SYS_ATA_BASE_ADDR + CONFIG_SYS_ATA_IDE0_OFFSET + CONFIG_SYS_ATA_REG_OFFSET + [1..7] */ -#define CONFIG_SYS_ATA_REG_OFFSET 0x0000 /* Offset for normal register accesses */ - -/* access to the alternate register is calculated: - CONFIG_SYS_ATA_BASE_ADDR + CONFIG_SYS_ATA_IDE0_OFFSET + CONFIG_SYS_ATA_ALT_OFFSET + 6 */ -#define CONFIG_SYS_ATA_ALT_OFFSET 0x03F0 /* Offset for alternate registers */ - -#endif /* IDE_USES_ISA_EMULATION */ - -#endif - -/* -#define CONFIG_SYS_KEY_REG_BASE_ADDR 0xF0100000 -#define CONFIG_SYS_IR_REG_BASE_ADDR 0xF0200000 -#define CONFIG_SYS_FPGA_REG_BASE_ADDR 0xF0300000 -*/ - -/*----------------------------------------------------------------------- - * Start addresses for the final memory configuration - * (Set up by the startup code) - * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 - * - * CONFIG_SYS_FLASH_BASE -> start address of internal flash - * CONFIG_SYS_MONITOR_BASE -> start of u-boot - */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_FLASH_BASE 0xFFE00000 - -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* Start of U-Boot */ -#define CONFIG_SYS_MONITOR_LEN (0xFFFFFFFF - CONFIG_SYS_MONITOR_BASE + 1) -#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserve 128 KiB for malloc() */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MiB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ -/*----------------------------------------------------------------------- - * FLASH organization ## FIXME: lookup in datasheet - */ -#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sectors on one chip */ - -#define CONFIG_SYS_FLASH_CFI /* flash is CFI compat. */ -#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver*/ -#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector */ -#define CONFIG_SYS_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash*/ -#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ -#define CONFIG_SYS_WRITE_SWAPPED_DATA /* swap Databytes between reading/writing */ - -#define CONFIG_ENV_IS_IN_FLASH 1 -#ifdef CONFIG_ENV_IS_IN_FLASH -#define CONFIG_ENV_OFFSET 0x00000000 /* Offset of Environment Sector in bottom type */ -#define CONFIG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */ -#define CONFIG_ENV_SECT_SIZE 0x4000 /* see README - env sector total size */ - -/* Address and size of Redundant Environment Sector */ -#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET+CONFIG_ENV_SIZE) -#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) - -#endif -/* let us changing anything in our environment */ -#define CONFIG_ENV_OVERWRITE - -/* - * NAND-FLASH stuff - */ -#define CONFIG_SYS_MAX_NAND_DEVICE 1 -#define CONFIG_SYS_NAND_BASE 0x77D00000 - -#define CONFIG_JFFS2_NAND 1 /* jffs2 on nand support */ - -/* No command line, one static partition */ -#undef CONFIG_CMD_MTDPARTS -#define CONFIG_JFFS2_DEV "nand0" -#define CONFIG_JFFS2_PART_SIZE 0x01000000 -#define CONFIG_JFFS2_PART_OFFSET 0x00000000 - -/* - * Init Memory Controller: - * - */ - -#define FLASH_BASE0_PRELIM CONFIG_SYS_FLASH_BASE -#define FLASH_BASE1_PRELIM 0 - -/*----------------------------------------------------------------------- - * Some informations about the internal SRAM (OCM=On Chip Memory) - * - * CONFIG_SYS_OCM_DATA_ADDR -> location - * CONFIG_SYS_OCM_DATA_SIZE -> size -*/ - -#define CONFIG_SYS_TEMP_STACK_OCM 1 -#define CONFIG_SYS_OCM_DATA_ADDR 0xF8000000 -#define CONFIG_SYS_OCM_DATA_SIZE 0x1000 - -/*----------------------------------------------------------------------- - * Definitions for initial stack pointer and data area (in DPRAM): - * - we are using the internal 4k SRAM, so we don't need data cache mapping - * - internal SRAM (OCM=On Chip Memory) is placed to CONFIG_SYS_OCM_DATA_ADDR - * - Stackpointer will be located to - * (CONFIG_SYS_INIT_RAM_ADDR&0xFFFF0000) | (CONFIG_SYS_INIT_SP_OFFSET&0x0000FFFF) - * in arch/powerpc/cpu/ppc4xx/start.S - */ - -#undef CONFIG_SYS_INIT_DCACHE_CS -/* Where the internal SRAM starts */ -#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR -/* Where the internal SRAM ends (only offset) */ -#define CONFIG_SYS_INIT_RAM_SIZE 0x0F00 - -/* - - CONFIG_SYS_INIT_RAM_ADDR ------> ------------ lower address - | | - | ^ | - | | | - | | Stack | - CONFIG_SYS_GBL_DATA_OFFSET ----> ------------ - | | - | 64 Bytes | - | | - CONFIG_SYS_INIT_RAM_SIZE ------> ------------ higher address - (offset only) - -*/ -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -/* Initial value of the stack pointern in internal SRAM */ -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -/* ################################################################################### */ -/* These defines will be used in arch/powerpc/cpu/ppc4xx/cpu_init.c to setup external chip selects */ -/* They are currently undefined cause they are initiaized in board/solidcard3/init.S */ - -/* This chip select accesses the boot device */ -/* It depends on boot select switch if this device is 16 or 8 bit */ - -#undef CONFIG_SYS_EBC_PB0AP -#undef CONFIG_SYS_EBC_PB0CR - -#undef CONFIG_SYS_EBC_PB1AP -#undef CONFIG_SYS_EBC_PB1CR - -#undef CONFIG_SYS_EBC_PB2AP -#undef CONFIG_SYS_EBC_PB2CR - -#undef CONFIG_SYS_EBC_PB3AP -#undef CONFIG_SYS_EBC_PB3CR - -#undef CONFIG_SYS_EBC_PB4AP -#undef CONFIG_SYS_EBC_PB4CR - -#undef CONFIG_SYS_EBC_PB5AP -#undef CONFIG_SYS_EBC_PB5CR - -#undef CONFIG_SYS_EBC_PB6AP -#undef CONFIG_SYS_EBC_PB6CR - -#undef CONFIG_SYS_EBC_PB7AP -#undef CONFIG_SYS_EBC_PB7CR - -#define CONFIG_SYS_EBC_CFG 0xb84ef000 - -#undef CONFIG_SDRAM_BANK0 /* use private SDRAM initialization */ -#undef CONFIG_SPD_EEPROM - -/* - * Define this to get more information about system configuration - */ -/* #define SC3_DEBUGOUT */ -#undef SC3_DEBUGOUT - -/*********************************************************************** - * External peripheral base address - ***********************************************************************/ - -#define CONFIG_SYS_ISA_MEM_BASE_ADDRESS 0x78000000 -/* - Die Grafik-Treiber greifen über die Adresse in diesem Macro auf den Chip zu. - Das funktioniert bei deren Karten, weil sie eine PCI-Bridge benutzen, die - das gleiche Mapping durchführen kann, wie der SC520 (also Aufteilen von IO-Zugriffen - auf ISA- und PCI-Zyklen) - */ -#define CONFIG_SYS_ISA_IO_BASE_ADDRESS 0xE8000000 -/*#define CONFIG_SYS_ISA_IO_BASE_ADDRESS 0x79000000 */ - -/************************************************************ - * Video support - ************************************************************/ - -#ifdef USE_VGA_GRAPHICS -#define CONFIG_VIDEO /* To enable video controller support */ -#define CONFIG_VIDEO_CT69000 -#define CONFIG_CFB_CONSOLE -/* #define CONFIG_VIDEO_LOGO */ -#define CONFIG_VGA_AS_SINGLE_DEVICE -#define CONFIG_VIDEO_SW_CURSOR -/* #define CONFIG_VIDEO_HW_CURSOR */ -#define CONFIG_VIDEO_ONBOARD /* Video controller is on-board */ - -#define VIDEO_HW_RECTFILL -#define VIDEO_HW_BITBLT - -#endif - -/************************************************************ - * Ident - ************************************************************/ -#define CONFIG_SC3_VERSION "r1.4" - -#define POST_OUT(x) (*((volatile unsigned char*)(0x79000080))=x) - -#endif /* __CONFIG_H */ |