diff options
Diffstat (limited to 'include')
| -rw-r--r-- | include/configs/stxssa.h | 418 |
1 files changed, 418 insertions, 0 deletions
diff --git a/include/configs/stxssa.h b/include/configs/stxssa.h new file mode 100644 index 0000000..f4ecb8f --- /dev/null +++ b/include/configs/stxssa.h @@ -0,0 +1,418 @@ +/* + * (C) Copyright 2005 Embedded Alley Solutions, Inc. + * Dan Malek <dan@embeddedalley.com> + * Copied from STx GP3. + * Updates for Silicon Tx GP3 SSA board. + * + * (C) Copyright 2002,2003 Motorola,Inc. + * Xianghua Xiao <X.Xiao@motorola.com> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* mpc8560ads board configuration file */ +/* please refer to doc/README.mpc85xx for more info */ +/* make sure you change the MAC address and other network params first, + * search for CONFIG_ETHADDR,CONFIG_SERVERIP,etc in this file + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* High Level Configuration Options */ +#define CONFIG_BOOKE 1 /* BOOKE */ +#define CONFIG_E500 1 /* BOOKE e500 family */ +#define CONFIG_MPC85xx 1 /* MPC8540/MPC8560 */ +#define CONFIG_CPM2 1 /* has CPM2 */ +#define CONFIG_STXSSA 1 /* Silicon Tx GPPP SSA board specific*/ + +#undef CONFIG_PCI /* pci ethernet support */ +#define CONFIG_TSEC_ENET /* tsec ethernet support*/ +#undef CONFIG_ETHER_ON_FCC /* cpm FCC ethernet support */ +#define CONFIG_ENV_OVERWRITE +#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */ +#undef CONFIG_DDR_ECC /* only for ECC DDR module */ +#undef CONFIG_DDR_DLL /* possible DLL fix needed */ +#define CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */ + + +/* sysclk for MPC85xx + */ + +#define CONFIG_SYS_CLK_FREQ 33000000 /* most pci cards are 33Mhz */ + +/* Blinkin' LEDs for Robert :-) +*/ +#define CONFIG_SHOW_ACTIVITY 1 + +/* + * These can be toggled for performance analysis, otherwise use default. + */ +#define CONFIG_L2_CACHE /* toggle L2 cache */ +#define CONFIG_BTB /* toggle branch predition */ +#define CONFIG_ADDR_STREAMING /* toggle addr streaming */ + +#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ + +#undef CFG_DRAM_TEST /* memory test, takes time */ +#define CFG_MEMTEST_START 0x00200000 /* memtest region */ +#define CFG_MEMTEST_END 0x00400000 + + +/* Localbus connector. There are many options that can be + * connected here, including sdram or lots of flash. + * This address, however, is used to configure a 256M local bus + * window that includes the Config latch below. + */ +#define CFG_LBC_OPTION_BASE 0xf0000000 /* Localbus Extension */ +#define CFG_LBC_OPTION_SIZE 256 /* 256MB */ + +/* There are various flash options used, we configure for the largest, + * which is 64Mbytes. The CFI works fine and will discover the proper + * sizes. + */ +#define CFG_FLASH_BASE 0xfc000000 /* start of FLASH 64M */ +#define CFG_BR0_PRELIM 0xfc001801 /* port size 32bit */ +#define CFG_OR0_PRELIM 0xfc000ff7 /* 64 MB Flash */ + +#define CFG_FLASH_CFI 1 +#define CFG_FLASH_CFI_DRIVER 1 +#undef CFG_FLASH_USE_BUFFER_WRITE /* use buffered writes (20x faster) */ +#define CFG_MAX_FLASH_SECT 256 /* max number of sectors on one chip */ +#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ + +#define CFG_FLASH_BANKS_LIST { CFG_FLASH_BASE } + +#define CFG_FLASH_PROTECTION + +/* The configuration latch is Chip Select 1. + * It's an 8-bit latch in the lower 8 bits of the word. + */ +#define CFG_LBC_CFGLATCH_BASE 0xfb000000 /* Base of config latch */ +#define CFG_BR1_PRELIM 0xfb001801 /* 32-bit port */ +#define CFG_OR1_PRELIM 0xffff0ff7 /* 64K is enough */ + +#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */ + +#if (CFG_MONITOR_BASE < CFG_FLASH_BASE) +#define CFG_RAMBOOT +#else +#undef CFG_RAMBOOT +#endif + +#ifdef CFG_RAMBOOT +#define CFG_CCSRBAR_DEFAULT 0x40000000 /* CCSRBAR by BDI cfg */ +#else +#define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ +#endif +#define CFG_CCSRBAR 0xe0000000 /* relocated CCSRBAR */ +#define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */ + + +/* + * DDR Setup + */ + +/* + * Base addresses -- Note these are effective addresses where the + * actual resources get mapped (not physical addresses) + */ +#define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory */ +#define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE + +#define SPD_EEPROM_ADDRESS 0x54 /* DDR DIMM */ + +#undef CONFIG_CLOCKS_IN_MHZ + +/* local bus definitions */ +#define CFG_BR2_PRELIM 0xf8001861 /* 64MB localbus SDRAM */ +#define CFG_OR2_PRELIM 0xfc006901 +#define CFG_LBC_LCRR 0x00030004 /* local bus freq */ +#define CFG_LBC_LBCR 0x00000000 +#define CFG_LBC_LSRT 0x20000000 +#define CFG_LBC_MRTPR 0x20000000 +#define CFG_LBC_LSDMR_1 0x2861b723 +#define CFG_LBC_LSDMR_2 0x0861b723 +#define CFG_LBC_LSDMR_3 0x0861b723 +#define CFG_LBC_LSDMR_4 0x1861b723 +#define CFG_LBC_LSDMR_5 0x4061b723 + +#define CONFIG_L1_INIT_RAM +#define CFG_INIT_RAM_LOCK 1 +#define CFG_INIT_RAM_ADDR 0x60000000 /* Initial RAM address */ +#define CFG_INIT_RAM_END 0x4000 /* End of used area in RAM */ + +#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + +#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ +#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ + +/* Serial Port */ +#define CONFIG_CONS_INDEX 2 +#undef CONFIG_SERIAL_SOFTWARE_FIFO +#define CFG_NS16550 +#define CFG_NS16550_SERIAL +#define CFG_NS16550_REG_SIZE 1 +#define CFG_NS16550_CLK get_bus_freq(0) + +#define CONFIG_BAUDRATE 38400 + +#define CFG_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} + +#define CFG_NS16550_COM1 (CFG_CCSRBAR+0x4500) +#define CFG_NS16550_COM2 (CFG_CCSRBAR+0x4600) + +/* Use the HUSH parser */ +#define CFG_HUSH_PARSER +#ifdef CFG_HUSH_PARSER +#define CFG_PROMPT_HUSH_PS2 "> " +#endif + +/* I2C */ +#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ +#define CONFIG_HARD_I2C /* I2C with hardware support*/ +#undef CONFIG_SOFT_I2C /* I2C bit-banged */ +#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CFG_I2C_SLAVE 0x7F +#if 0 +#define CFG_I2C_NOPROBES {0x00} /* Don't probe these addrs */ +#else +/* I did the 'if 0' so we could keep the syntax above if ever needed. */ +#undef CFG_I2C_NOPROBES +#endif +#define CFG_I2C_OFFSET 0x3000 + +/* I2C EEPROM. AT24C32, we keep our environment in here. +*/ +#define CFG_I2C_EEPROM_ADDR 0x51 /* 1010001x */ +#define CFG_I2C_EEPROM_ADDR_LEN 2 +#define CFG_EEPROM_PAGE_WRITE_BITS 5 /* =32 Bytes per write */ +#define CFG_EEPROM_PAGE_WRITE_ENABLE +#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 20 + +/* + * Standard 8555 PCI mapping. + * Addresses are mapped 1-1. + */ +#define CFG_PCI1_MEM_BASE 0x80000000 +#define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE +#define CFG_PCI1_MEM_SIZE 0x20000000 /* 512M */ +#define CFG_PCI1_IO_BASE 0x00000000 +#define CFG_PCI1_IO_PHYS 0xe2000000 +#define CFG_PCI1_IO_SIZE 0x01000000 /* 16M */ + +#define CFG_PCI2_MEM_BASE 0xa0000000 +#define CFG_PCI2_MEM_PHYS CFG_PCI2_MEM_BASE +#define CFG_PCI2_MEM_SIZE 0x20000000 /* 512M */ +#define CFG_PCI2_IO_BASE 0x00000000 +#define CFG_PCI2_IO_PHYS 0xe3000000 +#define CFG_PCI2_IO_SIZE 0x01000000 /* 16M */ + +#if defined(CONFIG_PCI) /* PCI Ethernet card */ + +#define CONFIG_NET_MULTI +#define CONFIG_PCI_PNP /* do pci plug-and-play */ + +#undef CONFIG_EEPRO100 +#undef CONFIG_TULIP + +#if !defined(CONFIG_PCI_PNP) + #define PCI_ENET0_IOADDR 0xe0000000 + #define PCI_ENET0_MEMADDR 0xe0000000 + #define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */ +#endif + +#undef CONFIG_PCI_SCAN_SHOW +#define CFG_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */ + +#endif /* CONFIG_PCI */ + +#if defined(CONFIG_TSEC_ENET) + +#ifndef CONFIG_NET_MULTI +#define CONFIG_NET_MULTI 1 +#endif + +#define CONFIG_MII 1 /* MII PHY management */ + +#define CONFIG_MPC85XX_TSEC1 1 +#define CONFIG_MPC85XX_TSEC1_NAME "TSEC0" +#define CONFIG_MPC85XX_TSEC2 1 +#define CONFIG_MPC85XX_TSEC2_NAME "TSEC1" +#undef CONFIG_MPS85XX_FEC + +#define TSEC1_PHY_ADDR 2 +#define TSEC2_PHY_ADDR 4 +#define TSEC1_PHYIDX 0 +#define TSEC2_PHYIDX 0 +#define CONFIG_ETHPRIME "TSEC0" + +#elif defined(CONFIG_ETHER_ON_FCC) /* CPM FCC Ethernet */ + +#define CONFIG_ETHER_ON_FCC2 /* define if ether on FCC */ +#undef CONFIG_ETHER_NONE /* define if ether on something else */ +#define CONFIG_ETHER_INDEX 2 /* which channel for ether */ + +#if (CONFIG_ETHER_INDEX == 2) + /* + * - Rx-CLK is CLK13 + * - Tx-CLK is CLK14 + * - Select bus for bd/buffers + * - Full duplex + */ + #define CFG_CMXFCR_MASK (CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK) + #define CFG_CMXFCR_VALUE (CMXFCR_RF2CS_CLK13 | CMXFCR_TF2CS_CLK14) + #define CFG_CPMFCR_RAMTYPE 0 +#if 0 + #define CFG_FCC_PSMR (FCC_PSMR_FDE) +#else + #define CFG_FCC_PSMR 0 +#endif + #define FETH2_RST 0x01 +#elif (CONFIG_ETHER_INDEX == 3) + /* need more definitions here for FE3 */ + #define FETH3_RST 0x80 +#endif /* CONFIG_ETHER_INDEX */ + +/* MDIO is done through the TSEC0 control. +*/ +#define CONFIG_MII /* MII PHY management */ +#undef CONFIG_BITBANGMII /* bit-bang MII PHY management */ + +#endif + +/* Environment */ +/* Config in EEPROM +*/ +#if 1 +#define CFG_ENV_IS_IN_EEPROM 1 +#define CFG_ENV_OFFSET 0 +#define CFG_ENV_SIZE 2048 +#else +#define CFG_ENV_IS_IN_FLASH 1 +#define CFG_ENV_SECT_SIZE 0x10000 + +#define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x00030000) +#define CFG_ENV_OFFSET 0 +#define CFG_ENV_SIZE 0x4000 +#endif + +#define CONFIG_BOOTARGS "root=/dev/nfs rw ip=any console=ttyS1,38400" +#define CONFIG_BOOTCOMMAND "bootm 0xffc00000 0xffd00000" +#define CONFIG_BOOTDELAY 3 /* -1 disable autoboot */ + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ + +#if defined(CFG_RAMBOOT) + #if defined(CONFIG_PCI) + #define CONFIG_COMMANDS ((CONFIG_CMD_DFL | CFG_CMD_PCI | \ + CFG_CMD_PING | CFG_CMD_I2C) & \ + ~(CFG_CMD_ENV | \ + CFG_CMD_LOADS )) + #elif defined(CONFIG_TSEC_ENET) + #define CONFIG_COMMANDS ((CONFIG_CMD_DFL | CFG_CMD_PING | \ + CFG_CMD_MII | CFG_CMD_I2C ) & \ + ~(CFG_CMD_ENV)) + #elif defined(CONFIG_ETHER_ON_FCC) + #define CONFIG_COMMANDS ((CONFIG_CMD_DFL | CFG_CMD_MII | \ + CFG_CMD_PING | CFG_CMD_I2C) & \ + ~(CFG_CMD_ENV)) + #endif +#else + #if defined(CONFIG_PCI) + #define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_PCI | \ + CFG_CMD_ELF | CFG_CMD_PING | CFG_CMD_I2C) + #elif defined(CONFIG_TSEC_ENET) + #define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_PING | \ + CFG_CMD_ELF | CFG_CMD_MII | CFG_CMD_I2C) + #elif defined(CONFIG_ETHER_ON_FCC) + #define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_MII | \ + CFG_CMD_ELF | CFG_CMD_PING | CFG_CMD_I2C) + #endif +#endif +#include <cmd_confdefs.h> + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +/* + * Miscellaneous configurable options + */ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "SSA=> " /* Monitor Command Prompt */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ +#define CFG_LOAD_ADDR 0x1000000 /* default load address */ +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +/* Cache Configuration */ +#define CFG_DCACHE_SIZE 32768 +#define CFG_CACHELINE_SIZE 32 +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ +#endif + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ +#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ +#endif + +/*Note: change below for your network setting!!! */ +#if defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC) +#define CONFIG_ETHADDR 00:e0:0c:07:9b:8a +#define CONFIG_HAS_ETH1 +#define CONFIG_ETH1ADDR 00:e0:0c:07:9b:8b +#define CONFIG_HAS_ETH2 +#define CONFIG_ETH2ADDR 00:e0:0c:07:9b:8c +#endif + +#define CONFIG_SERVERIP 192.168.85.1 +#define CONFIG_IPADDR 192.168.85.60 +#define CONFIG_GATEWAYIP 192.168.85.1 +#define CONFIG_NETMASK 255.255.255.0 +#define CONFIG_HOSTNAME STX_SSA +#define CONFIG_ROOTPATH /gppproot +#define CONFIG_BOOTFILE uImage +#define CONFIG_LOADADDR 0x1000000 + +#endif /* __CONFIG_H */ |