diff options
Diffstat (limited to 'include')
-rw-r--r-- | include/configs/zeus.h | 350 |
1 files changed, 0 insertions, 350 deletions
diff --git a/include/configs/zeus.h b/include/configs/zeus.h deleted file mode 100644 index 2bc4e1a..0000000 --- a/include/configs/zeus.h +++ /dev/null @@ -1,350 +0,0 @@ -/* - * (C) Copyright 2007 - * Stefan Roese, DENX Software Engineering, sr@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/************************************************************************ - * zeus.h - configuration for Zeus board - ***********************************************************************/ -#ifndef __CONFIG_H -#define __CONFIG_H - -/*----------------------------------------------------------------------- - * High Level Configuration Options - *----------------------------------------------------------------------*/ -#define CONFIG_ZEUS 1 /* Board is Zeus */ -#define CONFIG_405EP 1 /* Specifc 405EP support*/ - -#define CONFIG_SYS_TEXT_BASE 0xFFFC0000 - -#define CONFIG_SYS_CLK_FREQ 33000000 /* external frequency to pll */ - -#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ -#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */ - -#define PLLMR0_DEFAULT PLLMR0_333_111_55_111 -#define PLLMR1_DEFAULT PLLMR1_333_111_55_111 - -#define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */ - -#define CONFIG_OVERWRITE_ETHADDR_ONCE 1 - -#define CONFIG_PPC4xx_EMAC -#define CONFIG_MII 1 /* MII PHY management */ -#define CONFIG_PHY_ADDR 0x01 /* PHY address */ -#define CONFIG_HAS_ETH1 1 -#define CONFIG_PHY1_ADDR 0x11 /* EMAC1 PHY address */ -#define CONFIG_SYS_RX_ETH_BUFFER 16 /* Number of ethernet rx buffers & descriptors */ -#define CONFIG_PHY_RESET 1 -#define CONFIG_PHY_RESET_DELAY 300 /* PHY RESET recovery delay */ - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - -/* - * Command line configuration. - */ -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_CACHE -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_DIAG -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_ELF -#define CONFIG_CMD_I2C -#define CONFIG_CMD_IRQ -#define CONFIG_CMD_MII -#define CONFIG_CMD_PING -#define CONFIG_CMD_REGINFO - -/* POST support */ -#define CONFIG_POST (CONFIG_SYS_POST_MEMORY | \ - CONFIG_SYS_POST_CPU | \ - CONFIG_SYS_POST_CACHE | \ - CONFIG_SYS_POST_UART | \ - CONFIG_SYS_POST_ETHER) - -#define CONFIG_SYS_POST_ETHER_EXT_LOOPBACK /* eth POST using ext loopack connector */ - -/* Define here the base-addresses of the UARTs to test in POST */ -#define CONFIG_SYS_POST_UART_TABLE { CONFIG_SYS_NS16550_COM1 } - -#define CONFIG_LOGBUFFER -#define CONFIG_SYS_POST_CACHE_ADDR 0x00800000 /* free virtual address */ - -#define CONFIG_SYS_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */ - -#undef CONFIG_WATCHDOG /* watchdog disabled */ - -/*----------------------------------------------------------------------- - * SDRAM - *----------------------------------------------------------------------*/ -/* - * SDRAM configuration (please see cpu/ppc/sdram.[ch]) - */ -#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */ -#define CONFIG_SDRAM_BANK1 1 /* init onboard SDRAM bank 1 */ - -/* SDRAM timings used in datasheet */ -#define CONFIG_SYS_SDRAM_CL 3 /* CAS latency */ -#define CONFIG_SYS_SDRAM_tRP 20 /* PRECHARGE command period */ -#define CONFIG_SYS_SDRAM_tRC 66 /* ACTIVE-to-ACTIVE command period */ -#define CONFIG_SYS_SDRAM_tRCD 20 /* ACTIVE-to-READ delay */ -#define CONFIG_SYS_SDRAM_tRFC 66 /* Auto refresh period */ - -/*----------------------------------------------------------------------- - * Serial Port - *----------------------------------------------------------------------*/ -#define CONFIG_CONS_INDEX 1 -#define CONFIG_SYS_NS16550 -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE 1 -#define CONFIG_SYS_NS16550_CLK get_serial_clock() -#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* external serial clock */ -#define CONFIG_SYS_BASE_BAUD 691200 -#define CONFIG_BAUDRATE 115200 - -#define CONFIG_SYS_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400} - -/*----------------------------------------------------------------------- - * Miscellaneous configurable options - *----------------------------------------------------------------------*/ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ - -#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ -#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */ - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ - -#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ -#define CONFIG_LOOPW 1 /* enable loopw command */ -#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ -#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ -#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ - -/*----------------------------------------------------------------------- - * I2C - *----------------------------------------------------------------------*/ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_PPC4XX -#define CONFIG_SYS_I2C_PPC4XX_CH0 -#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 -#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F - -/* these are for the ST M24C02 2kbit serial i2c eeprom */ -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* base address */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* bytes of address */ -/* mask of address bits that overflow into the "EEPROM chip address" */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x07 - -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 /* 8 byte write page size */ -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ - -/* - * The layout of the I2C EEPROM, used for bootstrap setup and for board- - * specific values, like ethaddr... that can be restored via the sw-reset - * button - */ -#define FACTORY_RESET_I2C_EEPROM 0x50 -#define FACTORY_RESET_ENV_OFFS 0x80 -#define FACTORY_RESET_ENV_SIZE 0x80 - -/*----------------------------------------------------------------------- - * Start addresses for the final memory configuration - * (Set up by the startup code) - * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 - */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_FLASH_BASE 0xFF000000 -#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Monitor */ -#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */ -#define CONFIG_SYS_MONITOR_BASE (-CONFIG_SYS_MONITOR_LEN) - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/*----------------------------------------------------------------------- - * FLASH organization - */ -#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */ -#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */ - -#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE } - -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max number of sectors on one chip */ - -#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ - -#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ -#define CONFIG_SYS_FLASH_PROTECTION 1 /* use hardware flash protection */ - -#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ -#define CONFIG_SYS_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash */ - -#ifdef CONFIG_ENV_IS_IN_FLASH -#define CONFIG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */ -#define CONFIG_ENV_ADDR ((-CONFIG_SYS_MONITOR_LEN)-CONFIG_ENV_SECT_SIZE) -#define CONFIG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */ - -/* Address and size of Redundant Environment Sector */ -#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE) -#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) -#endif - -/*----------------------------------------------------------------------- - * Definitions for initial stack pointer and data area (in data cache) - */ -/* use on chip memory (OCM) for temperary stack until sdram is tested */ -#define CONFIG_SYS_TEMP_STACK_OCM 1 - -/* On Chip Memory location */ -#define CONFIG_SYS_OCM_DATA_ADDR 0xF8000000 -#define CONFIG_SYS_OCM_DATA_SIZE 0x1000 -#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* inside of OCM */ -#define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SYS_OCM_DATA_SIZE /* Size of used area in RAM */ - -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -/* reserve some memory for POST and BOOT limit info */ -#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_GBL_DATA_OFFSET - 16) - -/* extra data in OCM */ -#define CONFIG_SYS_POST_MAGIC \ - (CONFIG_SYS_OCM_DATA_ADDR + CONFIG_SYS_GBL_DATA_OFFSET - 8) -#define CONFIG_SYS_POST_VAL \ - (CONFIG_SYS_OCM_DATA_ADDR + CONFIG_SYS_GBL_DATA_OFFSET - 12) - -/*----------------------------------------------------------------------- - * External Bus Controller (EBC) Setup - */ - -/* Memory Bank 0 (Flash 16M) initialization */ -#define CONFIG_SYS_EBC_PB0AP 0x05815600 -#define CONFIG_SYS_EBC_PB0CR 0xFF09A000 /* BAS=0xFF0,BS=16MB,BU=R/W,BW=16bit */ - -/*----------------------------------------------------------------------- - * Definitions for GPIO setup (PPC405EP specific) - * - * GPIO0[0] - External Bus Controller BLAST output - * GPIO0[1-9] - Instruction trace outputs - * GPIO0[10-13] - External Bus Controller CS_1 - CS_4 outputs - * GPIO0[14-16] - External Bus Controller ABUS3-ABUS5 outputs - * GPIO0[17-23] - External Interrupts IRQ0 - IRQ6 inputs - * GPIO0[24-27] - UART0 control signal inputs/outputs - * GPIO0[28-29] - UART1 data signal input/output - * GPIO0[30-31] - EMAC0 and EMAC1 reject packet inputs - */ -#define CONFIG_SYS_GPIO0_OSRL 0x15555550 /* Chip selects */ -#define CONFIG_SYS_GPIO0_OSRH 0x00000110 /* UART_DTR-pin 27 alt out */ -#define CONFIG_SYS_GPIO0_ISR1L 0x10000041 /* Pin 2, 12 is input */ -#define CONFIG_SYS_GPIO0_ISR1H 0x15505440 /* OUT: LEDs 22/23; IN: pin12,2, NVALID# */ -#define CONFIG_SYS_GPIO0_TSRL 0x00000000 -#define CONFIG_SYS_GPIO0_TSRH 0x00000000 -#define CONFIG_SYS_GPIO0_TCR 0xBFF68317 /* 3-state OUT: 22/23/29; 12,2 is not 3-state */ -#define CONFIG_SYS_GPIO0_ODR 0x00000000 - -#define CONFIG_SYS_GPIO_SW_RESET 1 -#define CONFIG_SYS_GPIO_ZEUS_PE 12 -#define CONFIG_SYS_GPIO_LED_RED 22 -#define CONFIG_SYS_GPIO_LED_GREEN 23 - -/* Time in milli-seconds */ -#define CONFIG_SYS_TIME_POST 5000 -#define CONFIG_SYS_TIME_FACTORY_RESET 10000 - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#endif - -/* - * Pass open firmware flat tree - */ -#define CONFIG_OF_LIBFDT -#define CONFIG_OF_BOARD_SETUP - -/* ENVIRONMENT VARS */ - -#define CONFIG_PREBOOT "echo;echo Welcome to Bulletendpoints board v1.1;echo" -#define CONFIG_IPADDR 192.168.1.10 -#define CONFIG_SERVERIP 192.168.1.100 -#define CONFIG_GATEWAYIP 192.168.1.100 -#if 0 -#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ -#else -#define CONFIG_BOOTDELAY 3 /* autoboot after 5 seconds */ -#endif - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "logversion=2\0" \ - "hostname=zeus\0" \ - "netdev=eth0\0" \ - "ethact=ppc_4xx_eth0\0" \ - "netmask=255.255.255.0\0" \ - "ramdisk_size=50000\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw" \ - " nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw" \ - " ramdisk_size=${ramdisk_size}\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "addtty=setenv bootargs ${bootargs} console=ttyS0," \ - "${baudrate}\0" \ - "net_nfs=tftp ${kernel_mem_addr} ${file_kernel};" \ - "run nfsargs addip addtty;bootm\0" \ - "net_ram=tftp ${kernel_mem_addr} ${file_kernel};" \ - "tftp ${ramdisk_mem_addr} ${file_fs};" \ - "run ramargs addip addtty;" \ - "bootm ${kernel_mem_addr} ${ramdisk_mem_addr}\0" \ - "rootpath=/target_fs/zeus\0" \ - "kernel_fl_addr=ff000000\0" \ - "kernel_mem_addr=200000\0" \ - "ramdisk_fl_addr=ff300000\0" \ - "ramdisk_mem_addr=4000000\0" \ - "uboot_fl_addr=fffc0000\0" \ - "uboot_mem_addr=100000\0" \ - "file_uboot=/zeus/u-boot.bin\0" \ - "tftp_uboot=tftp 100000 ${file_uboot}\0" \ - "update_uboot=protect off fffc0000 ffffffff;" \ - "era fffc0000 ffffffff;cp.b 100000 fffc0000 40000;" \ - "protect on fffc0000 ffffffff\0" \ - "upd_uboot=run tftp_uboot;run update_uboot\0" \ - "file_kernel=/zeus/uImage_ba\0" \ - "tftp_kernel=tftp 100000 ${file_kernel}\0" \ - "update_kernel=protect off ff000000 ff17ffff;" \ - "era ff000000 ff17ffff;cp.b 100000 ff000000 180000\0" \ - "upd_kernel=run tftp_kernel;run update_kernel\0" \ - "file_fs=/zeus/rootfs_ba.img\0" \ - "tftp_fs=tftp 100000 ${file_fs}\0" \ - "update_fs=protect off ff300000 ff87ffff;era ff300000 ff87ffff;"\ - "cp.b 100000 ff300000 580000\0" \ - "upd_fs=run tftp_fs;run update_fs\0" \ - "bootcmd=chkreset;run ramargs addip addtty addmisc;" \ - "bootm ${kernel_fl_addr} ${ramdisk_fl_addr}\0" \ - "" - -#endif /* __CONFIG_H */ |