summaryrefslogtreecommitdiff
path: root/include
diff options
context:
space:
mode:
Diffstat (limited to 'include')
-rw-r--r--include/common.h4
-rw-r--r--include/configs/AP1000.h247
2 files changed, 2 insertions, 249 deletions
diff --git a/include/common.h b/include/common.h
index fb337791..b23e90b 100644
--- a/include/common.h
+++ b/include/common.h
@@ -42,7 +42,7 @@ typedef volatile unsigned char vu_char;
#include <linux/stringify.h>
#include <asm/ptrace.h>
#include <stdarg.h>
-#if defined(CONFIG_PCI) && (defined(CONFIG_4xx) && !defined(CONFIG_AP1000))
+#if defined(CONFIG_PCI) && defined(CONFIG_4xx)
#include <pci.h>
#endif
#if defined(CONFIG_8xx)
@@ -376,7 +376,7 @@ void pci_init (void);
void pci_init_board(void);
void pciinfo (int, int);
-#if defined(CONFIG_PCI) && (defined(CONFIG_4xx) && !defined(CONFIG_AP1000))
+#if defined(CONFIG_PCI) && defined(CONFIG_4xx)
int pci_pre_init (struct pci_controller *);
int is_pci_host (struct pci_controller *);
#endif
diff --git a/include/configs/AP1000.h b/include/configs/AP1000.h
deleted file mode 100644
index 09cfef6..0000000
--- a/include/configs/AP1000.h
+++ /dev/null
@@ -1,247 +0,0 @@
-/*
- * AMIRIX.h: AMIRIX specific config options
- *
- * Author : Frank Smith (smith at amirix dot com)
- *
- * Derived from : other configuration header files in this tree
- *
- * This software may be used and distributed according to the terms of
- * the GNU General Public License (GPL) version 2, incorporated herein by
- * reference. Drivers based on or derived from this code fall under the GPL
- * and must retain the authorship, copyright and this license notice. This
- * file is not a complete program and may only be used when the entire
- * program is licensed under the GPL.
- *
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_405 1 /* This is a PPC405 CPU */
-#define CONFIG_4xx 1 /* ...member of PPC4xx family */
-
-#define CONFIG_AP1000 1 /* ...on an AP1000 board */
-
-/*
- * Start at bottom of RAM, but at an aliased address so that it looks
- * like it's not in RAM. This is a bit of voodoo to allow it to be
- * run from RAM instead of Flash.
- */
-#define CONFIG_SYS_TEXT_BASE 0x08000000
-#define CONFIG_SYS_LDSCRIPT "board/amirix/ap1000/u-boot.lds"
-
-#define CONFIG_PCI 1
-
-#define CONFIG_SYS_HUSH_PARSER 1 /* use "hush" command parser */
-#define CONFIG_SYS_PROMPT "0> "
-
-#define CONFIG_COMMAND_EDIT 1
-#define CONFIG_COMPLETE_ADDRESSES 1
-
-#define CONFIG_ENV_IS_IN_FLASH 1
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
-
-#ifdef CONFIG_ENV_IS_IN_NVRAM
-#undef CONFIG_ENV_IS_IN_FLASH
-#else
-#ifdef CONFIG_ENV_IS_IN_FLASH
-#undef CONFIG_ENV_IS_IN_NVRAM
-#endif
-#endif
-
-#define CONFIG_BAUDRATE 57600
-#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */
-
-#define CONFIG_BOOTCOMMAND "" /* autoboot command */
-
-#define CONFIG_BOOTARGS "console=ttyS0,57600"
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_MVENV
-#define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
-
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-#define CONFIG_SYS_CLK_FREQ 30000000
-
-#define CONFIG_SPD_EEPROM 1 /* use SPD EEPROM for setup */
-
-/*
- * I2C
- */
-#define CONFIG_HARD_I2C /* I2C with hardware support */
-#define CONFIG_PPC4XX_I2C /* use PPC4xx driver */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-#define CONFIG_SYS_I2C_SPEED 400000
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-/* usually: (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+4+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_ALT_MEMTEST 1
-#define CONFIG_SYS_MEMTEST_START 0x00400000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x01000000 /* 4 ... 16 MB in DRAM */
-
-/*
- * If CONFIG_SYS_EXT_SERIAL_CLOCK, then the UART divisor is 1.
- * If CONFIG_SYS_405_UART_ERRATA_59, then UART divisor is 31.
- * Otherwise, UART divisor is determined by CPU Clock and CONFIG_SYS_BASE_BAUD value.
- * The Linux BASE_BAUD define should match this configuration.
- * baseBaud = cpuClock/(uartDivisor*16)
- * If CONFIG_SYS_405_UART_ERRATA_59 and 200MHz CPU clock,
- * set Linux BASE_BAUD to 403200.
- */
-#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* external serial clock */
-#undef CONFIG_SYS_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */
-
-#define CONFIG_SYS_NS16550_CLK 40000000
-#define CONFIG_SYS_DUART_CHAN 0
-#define CONFIG_SYS_NS16550_COM1 (0x4C000000 + 0x1000)
-#define CONFIG_SYS_NS16550_COM2 (0x4C800000 + 0x1000)
-#define CONFIG_SYS_NS16550_REG_SIZE 4
-#define CONFIG_SYS_NS16550 1
-#define CONFIG_SYS_INIT_CHAN1 1
-#define CONFIG_SYS_INIT_CHAN2 0
-
-/* The following table includes the supported baudrates */
-#define CONFIG_SYS_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400}
-
-#define CONFIG_SYS_LOAD_ADDR 0x00200000 /* default load address */
-#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-
-#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_FLASH_BASE 0x20000000
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_MONITOR_LEN (192 * 1024) /* Reserve 196 kB for Monitor */
-#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define CONFIG_SYS_FLASH_CFI 1
-#define CONFIG_SYS_PROGFLASH_BASE CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_CONFFLASH_BASE 0x24000000
-
-#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sectors on one chip */
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
-
-#define CONFIG_SYS_FLASH_PROTECTION 1 /* use hardware protection */
-
-/* BEG ENVIRONNEMENT FLASH */
-#ifdef CONFIG_ENV_IS_IN_FLASH
-#define CONFIG_ENV_OFFSET 0x00040000 /* Offset of Environment Sector */
-#define CONFIG_ENV_SIZE 0x1000 /* Total Size of Environment Sector */
-#define CONFIG_ENV_SECT_SIZE 0x20000 /* see README - env sector total size */
-#endif
-/* END ENVIRONNEMENT FLASH */
-/*-----------------------------------------------------------------------
- * NVRAM organization
- */
-#define CONFIG_SYS_NVRAM_BASE_ADDR 0xf0000000 /* NVRAM base address */
-#define CONFIG_SYS_NVRAM_SIZE 0x1ff8 /* NVRAM size */
-
-#ifdef CONFIG_ENV_IS_IN_NVRAM
-#define CONFIG_ENV_SIZE 0x1000 /* Size of Environment vars */
-#define CONFIG_ENV_ADDR \
- (CONFIG_SYS_NVRAM_BASE_ADDR+CONFIG_SYS_NVRAM_SIZE-CONFIG_ENV_SIZE) /* Env */
-#endif
-
-/*
- * Init Memory Controller:
- *
- * BR0/1 and OR0/1 (FLASH)
- */
-
-#define FLASH_BASE0_PRELIM CONFIG_SYS_FLASH_BASE /* FLASH bank #0 */
-#define FLASH_BASE1_PRELIM 0 /* FLASH bank #1 */
-
-/* Configuration Port location */
-#define CONFIG_PORT_ADDR 0xF0000500
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-
-#define CONFIG_SYS_INIT_RAM_ADDR 0x400000 /* inside of SDRAM */
-#define CONFIG_SYS_INIT_RAM_SIZE 0x2000 /* Size of used area in RAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Definitions for Serial Presence Detect EEPROM address
- * (to get SDRAM settings)
- */
-#define SPD_EEPROM_ADDRESS 0x50
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
-#endif
-
-/* JFFS2 stuff */
-
-#define CONFIG_SYS_JFFS2_FIRST_BANK 0
-#define CONFIG_SYS_JFFS2_NUM_BANKS 1
-#define CONFIG_SYS_JFFS2_FIRST_SECTOR 1
-
-#define CONFIG_E1000
-
-#define CONFIG_SYS_ETH_DEV_FN 0x0800
-#define CONFIG_SYS_ETH_IOBASE 0x31000000
-#define CONFIG_SYS_ETH_MEMBASE 0x32000000
-
-#endif /* __CONFIG_H */