summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2016-01-27net: phy: ti: Enable automatic crossover modeMichal Simek
Enable automatic crossover cable detection. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-27serial: zynq: Fix address reading from DMMichal Simek
Use dev_get_addr() instead of reading reg base directly in the driver. Core function is also more robust. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27serial: zynq: Extend compatible string listMichal Simek
ZynqMP is using updated core with cdns,uart-r1p12 compatible string. Signed-off-by: Michal Simek <monstr@monstr.eu> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27fpga: Fix compilation warningsMichal Simek
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27fpga: Add bitstream type BIT_NONESiva Durga Prasad Paladugu
Add bitstream type BIT_NONE to the bitstream type enum. This might be useful while loading bitstreams in respective drivers. Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27fpga: xilinx: Check for substring in device ID validationSiva Durga Prasad Paladugu
Check for substrings in deviceID validation check so that it can support xa bitstreams also. Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27microblaze: Fix board_init calling sequenceMichal Simek
board_init() is in final elf file but it is not called at all. Use board_init_late() instead and call gpio_init() from it. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27microblaze: Enable HUSH via KconfigMichal Simek
Cleanup board file. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27microblaze: Read information about RAM from DTMichal Simek
Do not setup ram start/size in board file. Read it from DT instead. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27microblaze: Remove empty file - cpu.cMichal Simek
No need to have empty unused file in architecture code. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27microblaze: Move CONFIG_NETCONSOLE to KconfigMichal Simek
Cleanup board file. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27microblaze: Remove CONFIG_FIT from board fileMichal Simek
And enable it via defconfig by default. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27microblaze: Remove systemace from board fileMichal Simek
Systemace is ancient IP which is not tested. Remove it from default configuration. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27microblaze: Move eth configuration to KconfigMichal Simek
Cleanup board specific file. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27microblaze: Enable axi emac via KconfigMichal Simek
Enable driver by default for all platforms. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27net: emaclite: Move emaclite to KconfigMichal Simek
Add PHYLIB and MII dependencies and enable it by default for Microblaze. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-27net: emaclite: Let core to handle received packetMichal Simek
Pass pointer to core to handle packet. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27net: emaclite: Rename start and stop functionsMichal Simek
Rename start and stop functions to align with DM functions names. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27net: emaclite: Move driver to DMMichal Simek
Move driver to DM. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-27net: emaclite: Use indirect access in emaclite_recvMichal Simek
When IP is configured with pong buffers, IP is receiving packets to ping and then to pong buffer and than ping again. The original logic in the driver remains there that when ping buffer is free, pong buffer is checked too and return if both are free. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27net: emaclite: Use indirect reg access in sendMichal Simek
The original logic in the driver was exchanging buffers which are used for sending packet and tx_ping and tx_pong buffers were exchanged all the time to ensure that IP has enough time to send the packet out. Based on this "feature" send function was using nextbuffertouse variable to save which buffer should be used. Before this algorithm was called driver checked that there is free buffer available. This checking remains in the driver but driver tries to use tx_ping first if available. If not, tx_pong buffer is used instead. To reach this code the original condition is met that at least one of the buffer should be available. Testing doesn't show any performance drop when this patch is applied. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-27net: emaclite: Remove XEL_TSR_XMIT_ACTIVE_MASK flagMichal Simek
This flag is not documented anywhere in the latest documentation that's why this patch removes it. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-27net: emaclite: Fix logic around available TX buffersMichal Simek
Simplify logic how to find out if there is free TX buffer. Both buffers are checked all the time that's why logic around order can be removed. Also add check when only one buffer is available. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-27net: emaclite: Use indirect register access for TX resetMichal Simek
Move to use indirect register access when timeout expires for resetting TX buffers. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-27net: emaclite: Use indirect register access for rx_ping/pongMichal Simek
Do initialization via indirect register access. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27net: emaclite: Use indirect register access for tx_ping/pongMichal Simek
Do initialization via indirect register access. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-27net: emaclite: Convert MDIO to use register offsetMichal Simek
Use u-boot coding style how to setup and access MDIO bus. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-27net: emaclite: Add MDIO support to driverMichal Simek
Add MDIO support before move to DM. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-27net: emaclite: Remove ancient OF probe functionMichal Simek
Prepare for DM move. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-27net: Add axi emac to KconfigMichal Simek
Also add dependency on PHYLIB and MII which is required. Clean PHYLIB dependency from the driver too. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-27net: axi_emac: Rename start, stop, write_hwaddr functionsMichal Simek
Rename few functions to fit to the new name convention used by DM. Suggested-by: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27net: axi_emac: Split recv from free_pktMichal Simek
Call net_process_received_packet() by core. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-27net: axi_emac: Enable access to MDIO in probeMichal Simek
Detect phy when driver probes. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-27net: axi_emac: Move driver to DMMichal Simek
Move driver to DM. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-27net: axi_emac: Pass private structure where possibleMichal Simek
Use axidma_priv instead of ethdevice in preparation of the DM move. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27net: axi_emac: Pass private structure to phyread/phywriteMichal Simek
Prepare for move to DM. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-27net: axi_emac: Put iobase to private structureMichal Simek
Saving iobase directly to private structure helps with moving to DM. There is an option to load iobase from pdata but it is additional load. Pointer to private structure is available all the time. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-27net: axi_emac: Pass directly pointer to register spaceMichal Simek
Simplify mdio_wait function by passing regs directly. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-27net: axi_emac: Show phy address instead of register contentMichal Simek
Fix debug message. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-27net: axi_emac: Fix parentheses around operand !Michal Simek
Fix these compilation warning by proper grouping: In function 'axi_dma_init': drivers/net/xilinx_axi_emac.c:391:7: warning: suggest parentheses around operand of '!' or change '&' to '&&' or '!' to '~' [-Wparentheses] if (!(in_be32(&priv->dmatx->control) | ^ In function 'axiemac_send': drivers/net/xilinx_axi_emac.c:501:21: warning: suggest parentheses around operand of '!' or change '&' to '&&' or '!' to '~' [-Wparentheses] while (timeout && (!in_be32(&priv->dmatx->status) & Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-27microblaze: Enable MICREL_KSZ9021Michal Simek
To solve enabling ETH_DM where ksz90x1_reg_field is defined only when additional Micrel type is defined. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27microblaze: Wire-up debug_uart in asmMichal Simek
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27microblaze: Remove unused I2C macrosMichal Simek
There is no i2c driver in the current u-boot. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27microblaze: Enable PHYLIB via KconfigMichal Simek
Cleanup board configuration. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27microblaze: Do not print eth device when DM_ETH is enabledMichal Simek
Doing the same fix as is done for ARM by: "Avoid calling print_eths() with driver model" (sha1: ff97380015b6b5d7d6267417a1cd6fc0e67b81bc) Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-27microblaze: Enable uart16550 DM by defaultMichal Simek
Microblaze is uses uartlite or uart16550 as console drivers. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27serial: uartlite: Add uartlite to KconfigMichal Simek
- Move config option out of board file. - Remove uartlite address from config file Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Thomas Chou <thomas@wytron.com.tw>
2016-01-27serial: uartlite: Add support for debug consoleMichal Simek
Add support for debug console. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Thomas Chou <thomas@wytron.com.tw>
2016-01-27serial: uartlite: Move driver to DMMichal Simek
Enable SPL DM too. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Thomas Chou <thomas@wytron.com.tw>
2016-01-27microblaze: Move baudrate setting out driver selectionMichal Simek
Preparation of moving to DM. Uartlite ignores baudrate setting. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
generated by cgit v0.10.2 at 2024-11-09 02:53:52 (GMT)