summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2013-05-24powerpc/t4240qds: fix PHY reset timeout issueShengzhou Liu
QSGMII card has different PHY address against previous SGMII card. We check the type of card in slots and set correct PHY address to avoid complainning "PHY reset timed out" during u-boot booting up. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-24powerpc/t4qds: Add SW7[4] in the DIP switch displayYork Sun
SW7[4] is the new bit which controls the mapping of eMMC vs SDHC. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-24Enable XAUI interface for B4860QDSSuresh Gupta
- Added SERDES2 PRTCLs = 0x98, 0x9E - Default Phy Addresses for Teranetics PHY on XAUI card The PHY addresses of Teranetics PHY on XAUI riser card are assigned based on the slot it is in. Switches SW4[2:4] and SW6[2:4] on AMC2PEX-2S On B4860QDS, AMC2PEX card decide the PHY addresses on slot1 and slot2 - Configure MDIO for 10Gig Mac Signed-off-by: Suresh Gupta <suresh.gupta@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-24board/t4240qds, b4860qds: LAW/TLB for DCSR set to size 32MStephen George
Debug trace buffers are memory mapped in DCSR space beyond 4M. Signed-off-by: Stephen George <stephen.george@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-24powerpc/p5040: enable PBL tool supportShaohui Xie
Provided a default RCW for P5040, then it can use PBL to build ramboot image. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-24powerpc/t4qds: use clock measurement for sysclk and ddr clockEd Swarthout
Use QIXIS measurement registers to obtain sysclk and ddr clock. This allows using non-standard clock speeds, set by directly writing to clock chip or store the values in qixis clock data eeprom. Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com> Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-24powerpc/qixis: add clock measurement registersEd Swarthout
QIXIS includes frequency measurement functions for each major processor clock input. After reset (and after clocks are stable), QIXIS measures the clocks against a reference frequency and stores the results in CLK_FREQ registers. A base register supplies a multiplier which allows directly obtaining the measured value, without requiring knowledge of the target system or QIXIS core frequency. Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com> Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-24powerpc/mpc8xxx: Allow DDR overclockYork Sun
Allow DDR clock runs faster than SPD specifes. This may cause memory failure, but the user should know what is going to happen when using higher than expected DDR clock. Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com> Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-24powerpc/chassis2: Change core numbering schemeYork Sun
To align with chassis generation 2 spec, all cores are numbered in sequence. The cores may reside across multiple clusters. Each cluster has zero to four cores. The first available core is numbered as core 0. The second available core is numbered as core 1 and so on. Core clocks are generated by each clusters. To identify the cluster of each core, topology registers are examined. Cluster clock registers are reorganized to be easily indexed. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-24powerpc/mpc8xxx: Add T1040 and variant SoCsYork Sun
T1040 and variants have e5500 cores and are compliant to QorIQ Chassis Generation 2. The major difference between T1040 and its variants is the number of cores and the number of L2 switch ports. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-24powerpc/T4160: Merge T4160 and T4240 in config_mpc85xx.hYork Sun
T4160 is a subset of T4240. Merge them in config_mpc85xx.h to simplify the defines. Also move CONFIG_E6500 out of t4qds.h into config_mpc85xx.h. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-24powerpc/p5040: enable NAND, SD, SPI boot supportShaohui Xie
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-24Add e6500 L2 replacement policy selectionJames Yang
This is compile-time config. Signed-off-by: James Yang <James.Yang@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-24T4240/ramboot: enable PBL tool for T4240Shaohui Xie
Added a default RCW(1_28_6_12) and PBI configure file for T4240, so it can use PBL tool to produce the ramboot image. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-24powerpc/t4240qds: Add VDD overrideYork Sun
Allow VDD voltage overriding with a command. This is an add-on feasture of VID. To override VDD, use command vdd_override with the value of voltage in mV, for example vdd_override <voltage in mV, eg. 1050> The above example will set the VDD to 1.050 volt. Any wrong value out of range of 0.8188 to 1.2125 volt or invalid string is ignored. In addition to the command, if overriding VDD is needed earlier in booting process, save an variable and reboot: setenv t4240qds_vdd_mv <voltage in mV> saveenv Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-24powerpc/mpc85xx: check if core is disabled for showing statusYork Sun
"cpu <num> status" should check if core is disabled before printing the spin table location. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-24net/phy: fix select line for TN80xxShaohui Xie
TN80xx has same PHY ID as TN2020, but it needs different setting to register 30.93 which used to select line, so we read register 30.32 which has bit 15:12 to indicate PHY hardware version, for TN20xx we will get 3 or 2, for TN80xx we will get 5 or 4. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-24Enable L2 cache parity/ECC error checkingJames Yang
Signed-off-by: James Yang <James.Yang@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-24powerpc/t4240qds: Add board detail for bdinfo commandYork Sun
Print more detail information including core voltage, RCW source, switch settings, etc. with bdinfo command. Signed-off-by: York Sun <yorksun@freescale.com> CC: Wolfgang Denk <wd@denx.de> CC: Tom Rini <trini@ti.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-24common: Update cmd_bdinfo for PPCYork Sun
Add board detail function to print more individual board information. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-24cmd_mem: fix cp commandMasahiro Yamada
The "cp" command has not worked since commit 0628ab8ec59834f98ede267edd21ddb8ba0bb57b, because of the following lines, which set the destination and the source to the same address. buf = map_sysmem(addr, bytes); src = map_sysmem(addr, bytes); Tested-by: Tom Rini <trini@ti.com> Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-05-24ext4: assign get_fs()->dev_desc before using itStephen Warren
Commit 50ce4c0 "fs/ext4: Support device block sizes != 512 bytes" modified ext4fs_set_blk_dev() to calculate total_sect based on get_fs()->dev_desc->log2blksz rather than SECTOR_SIZE. However, this value wasn't yet assigned. Move the assignment earlier so the code doesn't crash or hang. Cc: Egbert Eich <eich@suse.com> Tested-by: Tom Rini <trini@ti.com> Signed-off-by: Stephen Warren <swarren@nvidia.com>
2013-05-23cfi_flash: return NULL for invalid base address inputMasahiro Yamada
When base address given was out of valid flash address ranges, flash_get_info() function returned the pointer to the last element of flash_info[i] array. This patch changes this function to return NULL pointer in such a case, which is more correct behaviour. The function flash_protect_default() calls flash_protect() immediately after flash_get_info() invocation. With this correction, flash_protect() function would be able to return soon, for NULL flash_info. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Signed-off-by: Stefan Roese <sr@denx.de>
2013-05-23cosmetic: cfi_flash: delete a space after an unary operatorMasahiro Yamada
Linux Kernel Documentation/CodingStyle says: Do not add a space after unary operators such as &, *, ... Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Signed-off-by: Stefan Roese <sr@denx.de>
2013-05-23cfi_flash: Fix unaligned accesses to cfi_qry structureAndrew Gabbasov
Packed structure cfi_qry contains unaligned 16- and 32-bits members, accessing which causes problems when cfi_flash driver is compiled with -munaligned-access option: flash initialization hangs, probably due to data error. Since the structure is supposed to replicate the actual data layout in CFI Flash chips, the alignment issue can't be fixed in the structure. So, unaligned fields need using of explicit unaligned access macros. Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com> Reviewed-By: Albert ARIBAUD <albert.u.boot@aribaud.net> Signed-off-by: Stefan Roese <sr@denx.de>
2013-05-17Update MAINTAINERS file for sandboxSimon Glass
This currently has no maintainer listed. Signed-off-by: Simon Glass <sjg@chromium.org>
2013-05-17Update MAINTAINERS file for x86Simon Glass
This still shows the previous maintainer. Signed-off-by: Simon Glass <sjg@chromium.org>
2013-05-17.gitignore: add GNU GLOBAL filesMasahiro Yamada
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-05-17fdt_support: Use CONFIG_NR_DRAM_BANKS if definedDoug Anderson
It appears that there are some cases where we have more than 4 banks of memory. Use CONFIG_NR_DRAM_BANKS if it's defined to handle this. This will take up a little extra stack space (64 bytes extra if we go up to 8 banks), but that seems OK. Signed-off-by: Doug Anderson <dianders@chromium.org>
2013-05-17bootm: Avoid 256-byte overflow in fixup_silent_linux()Doug Anderson
This makes fixup_silent_linux() use malloc() to allocate its working space, meaning that our maximum kernel command line should only be limited by malloc(). Previously it was silently overflowing the stack. Note that nothing about this change increases the kernel's maximum command line length. If you have a command line that is >256 bytes it's up to you to make sure that kernel can handle it. Signed-off-by: Doug Anderson <dianders@chromium.org> Acked-by: Mike Frysinger <vapier@gentoo.org>
2013-05-16README: Correct reference for CONFIG_SUPPORT_RAW_INITRDTom Rini
Signed-off-by: Tom Rini <trini@ti.com>
2013-05-15powerpc/esdhc: Correct judgement for DATA PIO modeHaijun.Zhang
The logic for the whether to configure for polling or DMA was mistakenly reversed in this patch: Commit 7b43db92110ec2f15c5f7187a165f2928464966b drivers/mmc/fsl_esdhc.c: fix compiler warnings Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com> CC: Sun Yusong-R58495 <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-15mmc: update Faraday FTSDC010 for rw performanceKuo-Jung Su
Faraday FTSDC010 is a MMC/SD host controller. Although there is already a driver in current u-boot release, which is modified from eSHDC and contributed by Andes Tech. Its performance is too terrible on Faraday A36x SoC platforms, so I turn to implement this new version of driver which is 10+ times faster than the old one. It's carefully designed to be compatible with Andes chips, so it should be safe to replace it. Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com> CC: Andy Fleming <afleming@gmail.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-15Merge branch 'master' of git://www.denx.de/git/u-boot-mpc85xxTom Rini
2013-05-15Power: remove support for Freescale MPC8220Wolfgang Denk
The Freescale MPC8220 Power Architecture processors have long reached EOL; Freescale does not even list these any more on their web site. Remove the code to avoid wasting maitaining efforts on dead stuff. Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Andy Fleming <afleming@gmail.com>
2013-05-15doc/README.scrapyard: add missing commit IDsWolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2013-05-15drivers/mmc: move spl_mmc.c to common/splYing Zhang
The mpc85xx repuires a special layout on the memory device that is connected to the eSDHC controller interface. But the file spl_mmc.c didn't handle this specfic case, there needs a special treatmen, in the powerpc drictory. So, there is no longer to keep spl_mmc.c on mpc85xx, CONFIG_SPL_FRAMEWORK is not set. When CONFIG_SPL_MMC_SUPPORT is set and CONFIG_SPL_FRAMEWORK is not set, there was an error in drivers/mmc/spl_mmc.c: drivers/mmc/libmmc.o:(.got2+0x8): undefined reference to `spl_image'. Now, the solution is to move the file "spl_mmc.c" to directory "common/spl". Signed-off-by: Ying Zhang <b40530@freescale.com>
2013-05-15smc911x: fix the timeout detectionMasahiro Yamada
If timeout is occurred at the while loop above, the value of 'timeout' is -1, not 0. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-05-15doc/README.ubi: Add description of accessing ubi filesystemsPaul B. Henson
Signed-off-by: "Paul B. Henson" <henson@acm.org>
2013-05-14T4240/eth: fix SGMII card PHY addressShaohui Xie
QSGMII card assumed to be used by default, but if SGMII card is used, it will use different PHY address, but we don't know which card is used until we access PHY on the card. So we check the card type slot by slot, if we can read a PHY ID by reading a SGMII PHY address on a slot, then the slot must have a SGMII card pluged, we mark all ports on that slot, and fix dts to use the SGMII card PHY address when doing dts fixup for the marked ports. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-14powerpc/t4qds: Fix disabling remote I2C connectionEd Swarthout
Only clear IRE bit in qixis brdcfg5 register and keep other bits unchanged. Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com> Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-14powerpc/b4860qds: Assign DDR address in board fileYork Sun
B4860QDS requires DDRC2 has 0 as base address and DDRC1 has higher address. This is the requirement for DSP cores to run in 32-bit address space. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-14powerpc/mpc8xxx: Allow board file to override DDR address assignmentYork Sun
This gives boards flexibility to assign other than default addresses to each DDR controller. For example, DDR controler 2 can have 0 as the base and DDR controller 1 has higher memory. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-14powerpc/mpc85xx: Update workaround for DDR erratum A-004934York Sun
The workaround has been updated to use a slightly different magic number. Change from 0x00003000 to 0x30003000. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-14T4/usb: move usb 2.0 utmi dual phy init code to cpu_init.cRoy Zang
This is what we have done for the UTMI PHY on P3041/P5020. Then the PHY initialization can be reused in kernel without “usb start” command. Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-14T4240/net: use QSGMII card PHY address by defaultShaohui Xie
Use QSGMII card PHY address as default SGMII card PHY address, QSGMII card PHY address is variable depends on different slot. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-14net/phy: add VSC8574 supportShaohui Xie
The VSC8574 is a quad-port Gigabit Ethernet transceiver with four SerDes interfaces for quad-port dual media capability. This driver supports SGMII and QSGMII MAC mode. For now SGMII mode is tested. Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-14powerpc/85xx: fix build error introduced by serdes_get_prtclShengzhou Liu
Removed unused declare serdes_get_prtcl() which was no longer needed. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-14net/fm: fixup ethernet for mEMACShengzhou Liu
- set proper compatible property name for mEMAC. - fixed ft_fixup_port for dual-role mEMAC, which will lead to MAC node disabled incorrectly. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-14t4240qds/eth: fixup ethernet for t4240qdsShengzhou Liu
1, Implemented board_ft_fman_fixup_port() to fix port for kernel. 2, Implemented fdt_fixup_board_enet() to fix node status of different slots and interfaces. 3, Adding detection of slot present for XGMII interface. 4, There is no PHY for XFI, so removed related phy address settings. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
generated by cgit v0.10.2 at 2024-09-02 10:44:48 (GMT)