| Age | Commit message (Collapse) | Author |
|---|
|
The following changes are made to the clock API:
* The concept of "clocks" and "peripheral clocks" are unified; each clock
provider now implements a single set of clocks. This provides a simpler
conceptual interface to clients, and better aligns with device tree
clock bindings.
* Clocks are now identified with a single "struct clk", rather than
requiring clients to store the clock provider device and clock identity
values separately. For simple clock consumers, this isolates clients
from internal details of the clock API.
* clk.h is split so it only contains the client/consumer API, whereas
clk-uclass.h contains the provider API. This aligns with the recently
added reset and mailbox APIs.
* clk_ops .of_xlate(), .request(), and .free() are added so providers
can customize these operations if needed. This also aligns with the
recently added reset and mailbox APIs.
* clk_disable() is added.
* All users of the current clock APIs are updated.
* Sandbox clock tests are updated to exercise clock lookup via DT, and
clock enable/disable.
* rkclk_get_clk() is removed and replaced with standard APIs.
Buildman shows no clock-related errors for any board for which buildman
can download a toolchain.
test/py passes for sandbox (which invokes the dm clk test amongst
others).
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
This adds a sandbox reset implementation (provider), a test client
device, instantiates them both from Sandbox's DT, and adds a DM test
that excercises everything.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
A reset controller is a hardware module that controls reset signals that
affect other hardware modules or chips.
This patch defines a standard API that connects reset clients (i.e. the
drivers for devices affected by reset signals) to drivers for reset
controllers/providers. Initially, DT is the only supported method for
connecting the two.
The DT binding specification (reset.txt) was taken from Linux kernel
v4.5's Documentation/devicetree/bindings/reset/reset.txt.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Tegra186's HSP module implements doorbells, mailboxes, semaphores, and
shared interrupts. This patch provides a driver for HSP, and hooks it
into the mailbox API. Currently, only doorbells are supported.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Rename mailbox*.h to match the naming convention requested during review
of the new reset subsystem.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
The documentation of parameters in arch/sandbox/include/asm/gpio.h is
either missing or faulty.
This patch corrects the documentation.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
A number of style fixes across the files in this directory, including:
* Correct invalid kernel-doc content.
* Tidy up massive comment in fdt_region.c.
* Use correct spelling of "U-Boot".
* Replace tests of "! <var>" with "!<var>".
* Replace "libfdt_env.h" with <libfdt_env.h>.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
A bug in the pca953x driver prevents correct reading of GPIO input
values beyond the 8th GPIO; all values are reported as zero. Setting of
GPIO output values is not affected.
This patch fixes the reading behavior.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Peng Fan <van.freenix@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Some architectures as m68k still need to use CONFIG_NEEDS_MANUAL_RELOC,
and are not still using the device tree.
Signed-off-by: Angelo Dureghello <angelo@sysam.it>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Correct the error message in spl_load_image_ext() when image parsing
fails. Instead of "ext4fs_read failed" print "failed to parse image
header".
Signed-off-by: Petr Kulhavy <brain@jikos.cz>
CC: Guillaume GARDET <guillaume.gardet@free.fr>
CC: Tom Rini <trini@konsulko.com>
|
|
Fix the following build errors when building sandbox on x86 32-bit:
In file included from fs/cbfs/cbfs.c:8:0:
include/malloc.h:364:7: error: conflicting types for 'memset'
void* memset(void*, int, size_t);
^
In file included from include/compiler.h:123:0,
from include/cbfs.h:10,
from fs/cbfs/cbfs.c:7:
include/linux/string.h:78:15: note: previous declaration of 'memset' was here
extern void * memset(void *,int,__kernel_size_t);
^
In file included from fs/cbfs/cbfs.c:8:0:
include/malloc.h:365:7: error: conflicting types for 'memcpy'
void* memcpy(void*, const void*, size_t);
^
In file included from include/compiler.h:123:0,
from include/cbfs.h:10,
from fs/cbfs/cbfs.c:7:
include/linux/string.h:81:15: note: previous declaration of 'memcpy' was here
extern void * memcpy(void *,const void *,__kernel_size_t);
^
scripts/Makefile.build:280: recipe for target 'fs/cbfs/cbfs.o' failed
Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
CONFIG_VERSION_VARIABLE isn't always defined, so we can't simply look up
its value directly, or an exception will occur if it isn't defined.
Instead, we must use .get() to supply a default value if the variable
isn't defined.
Fixes: da37f006e7c5 ("tests: py: disable main_signon check for printenv cmd")
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
|
|
Signed-off-by: Tom Rini <trini@konsulko.com>
Conflicts:
arch/arm/include/asm/arch-fsl-layerscape/immap_lsch3.h
|
|
|
|
Currently DFU is not working.
Adjust CONFIG_SYS_MALLOC_LEN and dfu_alt_info so that we are
able to flash u-boot.imx into the eMMC via dfu using the
following method:
=> dfu 0 mmc 0
In the host PC:
dfu-util -D u-boot.imx -a boot
This is the same approach done in the mx6sl warp board.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
|
|
Add a README file for helping users to install U-Boot into the eMMC.
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Acked-by: Fabio Estevam <fabio.estevam@nxp.com>
|
|
The latest version of warp7 board provides the connection of the
WDOG1_B pin to the PMIC.
Program the watchdog to enable the WDOG1_B output which causes
a POR reset.
Based on the imx7dsabresd code.
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Acked-by: Fabio Estevam <fabio.estevam@nxp.com>
|
|
The current pad DSE for QSPI is 60ohm. This setting cause
too strong drive to clock and data signals. Need to change
the DSE to 120ohm for better signal quality.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
|
|
Q901 is PMOS, LCD_nPWREN should be at low voltage then output is 3V3.
If LCD_nPWREN is high, output is 2.4V which is not correct.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
|
|
Fix 74LV OE gpio index. gpio index is wrong,
so gpio output will not have effect, since we
use wrong GPIO5_IO18, but not correct GPIO5_IO8.
And at the end of the initialization of 74lv init, should
keep OE voltage level at LOW to make 74lv output the correct
voltage.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
|
|
LCD_PWR_EN controls the G pin of Q13 PMOS which needs low voltage to connect
D to S for outputting LCD 3.3V. If LCD_PWR_EN is high, we measured the LCD 3v3
is actually 1.2V.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
|
|
Currently the LVDS backlight does not work in U-Boot after a “reboot” comand
in the kernel.
This problem occurs because the kernel uses this pin in PWM mode and U-Boot
does not configure the backlight pin as GPIO functionality.
So fix the problem by explicitly configuring the backlight pin as GPIO in
U-Boot.
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
|
|
Signed-off-by: Stefano Babic <sbabic@denx.de>
|
|
If the usb controller is not running, no need to shutdown it,
otherwise `usb stop` complains about:
"EHCI failed to shut down host controller".
To i.MX7D SDB, there are two usb ports, one Host, one OTG.
If we only plug one udisk to the Host port and then `usb start`,
the OTG controller for OTG port does not run actually. Then,
if `usb stop`, the OTG controller for OTG port will also be
shutdown, but it is not running.
This patch adds a check to only shutdown the running controller.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: "Stefan Brüns" <stefan.bruens@rwth-aachen.de>
Cc: Stephen Warren <swarren@nvidia.com>
|
|
For legacy usb storage driver, USB_MAX_STOR_DEV is defined as 7.
If we only have one usb disk on board, `usb dev 0` is ok.
But if `usb dev 1`, still ok, then `usb read xxx` will trigger
system fault and reboot.
So check if_type before using this device.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stephen Warren <swarren@nvidia.com>
|
|
The setjmp/longjmp implementation did not work on thumb1 implementations
because it used instruction encodings that don't exist on thumb1 yet.
This patch limits itself to thumb1 instruction set for 32bit arm and
removes a superfluous printf along the way.
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
enable basic DM/DTS support for the siemens am335x based boards.
Signed-off-by: Heiko Schocher <hs@denx.de>
|
|
add missing USB_MUSB_* and CONFIG_G_DNL_*
board configuration.
Signed-off-by: Heiko Schocher <hs@denx.de>
|
|
Enable FIT support for AM57xx platforms using the high-security (HS)
device variant.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
twister board was not updated after changing
SPL defines, resulting in a broken board.
Signed-off-by: Stefano Babic <sbabic@denx.de>
|
|
I no longer have access to such a board
Signed-off-by: Thomas Lange <thomas@corelatus.se>
|
|
Remove redundant #if defined(CONFIG_SPL_OS_BOOT) statement around
getenv() calls in spl_load_image_ext_os().
The whole function is surrounded by #ifdef CONFIG_SPL_OS_BOOT.
No functional change.
Signed-off-by: Petr Kulhavy <brain@jikos.cz>
CC: Guillaume GARDET <guillaume.gardet@free.fr>
Acked-by: Guillaume GARDET <guillaume.gardet@free.fr>
|
|
The comments in the source file are riddled with spelling mistakes. Be
a good citizen and take a stab at cleaning up some of the more obvious
ones.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Adds FIT support to the SPL and u-boot for AM437x HS devices.
Signed-off-by: Madan Srinivas <madans@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
Adds missing NAND option to CONFIG_SYS_EXTRA_OPTIONS for
AM437x HS EVMs. This syncs up the config options between
GP and HS EVMs.
Signed-off-by: Madan Srinivas <madans@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
With updated moveconfig.py and an better default, re-generate
the migration of BOOTDELAY to the defconfig.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
The value of 0 is fairly uncommon while 2 is one of the more common ones
so switch.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
|
|
Add support for loading splash image from NAND Flash formatted with a (UBI) filesystem.
Signed-off-by: Eran Matityahu <eran.m@variscite.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Tom Rini <trini@konsulko.com>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Nikita Kiryanov <nikita@compulab.co.il>
|
|
This patch is doing the following:
1. Implementing the errata for LS2080.
2. Adding fixup for fdt for LS2080.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
|
|
This errata a008751 is applied on Soc specific file currently.This will be
moved to a file where all the errata implementation will take place for usb
for fsl. This patch removes the errata workaround from soc specific file
for LS2080.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
|
|
This patch does the following things:
1. Makes the errata checking code common for PPC and ARM
2. Moves all these static inline functions into a dedicated C file
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
|
|
Performs code cleanup for device tree fixup for fsl usb controllers by
making functions to handle these similar errata checking code.
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
|
|
Adds get_svr and IS_SVR_REV helpers for ARMv8 platforms,
similar to PPC and ARMv7.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
|
|
The Kona PHY supports an 8-bit wide UTMI interface,
therefore, choose this Kconfig setting.
Signed-off-by: Steve Rae <srae@broadcom.com>
|
|
Define CONFIG_USB_GADGET_DWC2_OTG_PHY_BUS_WIDTH_8 to allow the
physical interface to be 8-bit (rather than 16-bit).
Signed-off-by: Steve Rae <srae@broadcom.com>
|
|
Select a right dtb from FIT for am437x-hs platform.
Reported-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
Add proper dtb file name for AM572x-IDK in env.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
Add initial DTS support for AM572-IDK evm.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Schuyler Patton <spatton@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
