| Age | Commit message (Collapse) | Author |
|---|
|
Add LPC32xx GPIO interface macro for pin mapping.
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
|
|
Add support for optional soft reset (i.e. "RESOUT_N" not asserted during reset).
To be compatible with the original U-Boot code, when the "addr" parameter is 0, a hard is performed; for any other values, a soft reset is done.
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
|
|
Add missing registers in struct definition.
Update GPIO MUX base register to match GPIO base (refer to "LPC32x0 User manual" Rev. 3 - 22 July 2011).
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
|
|
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
|
|
|
|
Also update maintainer info.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
|
|
Also update maintainer info.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
|
|
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: York Sun <yorksun@freescale.com>
|
|
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
|
|
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
|
|
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
|
|
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
|
|
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
|
|
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
|
|
The default boot command searches for dofastboot varaiable
and does a fastboot if it is set to 1.
But the condition "if test ${dofastboot} -eq 1" always
returns true if dofastboot is not defined and breaking mmc boot.
So make dofastboot as 0 by default and let the runtime
environment set it if fastboot is required.
Reported-by: Yan Liu <yan-liu@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
This reverts commit 5b34436035fc862b5e8d0d2c3eab74ba36f1a7f4.
This function has a few problems. It calls fdt_parent_offset() which as
mentioned in code review is very slow.
https://patchwork.ozlabs.org/patch/499482/
https://patchwork.ozlabs.org/patch/452604/
It also happens to break SPI flash on Minnowboard max which is how I noticed
that this was applied. I can send a patch to tidy that up, but in any case
I think we should consider a revert until the function is better implemented.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
It is a bit tedious to figure out the interrupt configuration for a new
x86 platform. Add a script which can do this, based on the output of
'pci long'. This may be helpful in some cases.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Set up interrupts correctly so that Linux can use all devices. Use
savedefconfig to regenerate the defconfig file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
* Explicitly list the targets supported in each section of the
instructions from the x86 README.
* Drop references to 'raw mode', in favor of 'bare mode'.
Signed-off-by: Igor Stoppa <igor.stoppa@intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
This can fail for internal reasons, so return a sensible value rather than
a random one.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Now that we have an efi.h header we can use that for FSP error defines.
Drop the FSP ones.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Multiple APs are brought up simultaneously and they may get the same
seq num in the uclass_resolve_seq() during device_probe(). To avoid
this, set req_seq to the reg number in the device tree in advance.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
There is one typo in the VESA mode 105h string. Correct it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
When trying to figure out where an exception has occured, the relocated
address is not a lot of help. Its value depends on various factors. Show
the un-relocated IP as well. This can be looked up in System.map directly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Move to driver model for networking on minnowmax.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Move to driver model for USB on minnowmax.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
This reverts commit df189d9ba3f8fd1bc67e3c0c3c4ace16cd065ee1.
Unfortunately this commit breaks chromebook_link because it adds lots of PCI devices
before relocation and there is not enough pre-reloc malloc() memory.
Rathar then increase this memory, revert for now until we figure this out.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
There is quite a bit of assembler code that can be removed if we use the
generic global_data setup. Less arch-specific code makes it easier to add
new features and maintain the start-up code.
Drop the unneeded code and adjust the hooks in board_f.c to cope.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Rather than keeping track of the Global Descriptor Table in its own memory
we may as well put it in global_data with everything else. As a first step,
stop using the separately allocated GDT.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
At present we have a simple assignment to gd. With some archs this is
implemented as a register or through some other means; a simple assignment
does not suit in all cases.
Change this to a function and add documentation to describe how this all
works.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <yorksun@freescale.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Some archs like to have larger alignment for their global data. Use 16 bytes
which suits all current archs.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Remove FAT function prototypes from the cm5200 firmware update code, and
include the relevant headers instead.
This exposes the fact that the custom prototyoe for do_fat_read() in
this file was incorrect. Rather than simply fixing the call-site, replace
do_fat_read() with fat_exists(). This removes the only use of
do_fat_read() outside of the FAT code.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
|
|
This part of mentioned commit, was missed by my mistake during the rebase.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Original commit message:
power: pmic: pfuze100 support driver model
1. Support driver model for pfuze100.
2. Introduce a new Kconfig entry DM_PMIC_PFUZE100 for pfuze100
3. This driver intends to support PF100, PF200 and PF3000, so add
the device id into the udevice_id array.
4. Rename PMIC_NUM_OF_REGS macro to PFUZE100_NUM_OF_REGS.
Change-Id: I4fc88414f3c0285f9648e47ec7aed60addeccc4d
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
This is declared but no-longer exists. Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
We should not fiddle with interrupts or the FSP when running as an EFI
payload. Detect this and skip this code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
We should signal to the FSP that PCI enumeration is complete. Perform this
task in a suitable place.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
This function can fail. In this case we should return the error rather than
swallowing it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
This code may be useful for boards that use driver model for PCI.
Note: It would be better to have driver model automatically call this
function somehow. However for now it is probably safer to have it under
board control.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
This code could use a little tightening up. There is some repetition and
an odd use of fdtdec_get_int_array().
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Use savedefconfig to get this file into the correct order.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
These functions allow iteration through all PCI devices including bridges.
The children of each PCI bus are returned in turn. This can be useful for
configuring, checking or enumerating all the devices.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
At present there are no PCI functions which allow access to PCI
configuration using a struct udevice. This is a sad situation for driver
model as it makes use of PCI harder. Add these functions.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
When using different release version of Intel FSP, the VPD_IMAGE_REV
is different (ie: BayTrail Gold 3 is 0x0303 while Gold 4 is 0x0304).
Remove the asserting of this so that U-Boot does not hang in a debug
build.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Allow for configuration of FSP UPD from the device tree which will
override any settings which the FSP was built with itself.
Modify the MinnowMax and BayleyBay boards to transfer sensible UPD
settings from the Intel FSPv4 Gold release to the respective dts files,
with the condition that the memory-down parameters for MinnowMax are
also used.
Signed-off-by: Andrew Bradford <andrew.bradford@kodakalaris.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Removed fsp,mrc-debug-msg and fsp,enable-xhci for minnowmax, bayleybay
Fixed lines >80col
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
The BayTrail SoC has 4 different PCI devices IDs regarding to IDE
and AHCI. Add these IDs in pci_ids.h and also add the other SATA
ID in the Bayley Bay and MinnowMax board configuration header.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
|
|
bd->bi_dram[] has both start address and size defined as 32-bit,
which is not the case on some platforms where >=4GiB memory bank
is used. Change them to support such memory banks.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Add support for 4 1.62G lane eDP panels connected via an anx9804 bridge,
such as found on the Colombus devkit.
While at it also fix the wrong indentation of the SSD2828 Kconfig help text
in board/sunxi/Kconfig.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
Add support for the ANX9804 bridge chip, which can take pixel data coming
from a parallel LCD interface and translate it on the fly into a DP
interface for driving eDP TFT displays. It uses I2C for configuration.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Anatolij Gustschin <agust@denx.de>
|
|
Add support for using the mipi pll as lcd clock source, this is
necessary for getting higher dotclocks with lcd panels.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Anatolij Gustschin <agust@denx.de>
|
