summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2013-08-15Add TI816X evm board supportTENART Antoine
Signed-off-by: Antoine Tenart <atenart@adeneo-embedded.com> [trini: Change to SPDX, fix a few compiler warnings, adapt to CONFIG_OMAP_COMMON] Signed-off-by: Tom Rini <trini@ti.com>
2013-08-15Add TI816X supportTENART Antoine
Signed-off-by: Antoine Tenart <atenart@adeneo-embedded.com> [trini: Fix warnings about vtp things in emif4.c, adapt AM43XX] Signed-off-by: Tom Rini <trini@ti.com>
2013-08-15Prepare for TI816X : reuse existing code from TI814XTENART Antoine
Rename some CONFIG_TI814X to a more generic CONFIG_TI81XX Signed-off-by: Antoine Tenart <atenart@adeneo-embedded.com> [trini: Adapt for CONFIG_OMAP_COMMON changes, AM43XX] Signed-off-by: Tom Rini <trini@ti.com>
2013-08-15arm, da850: add ipam390 board supportHeiko Schocher
add the am1808 based ipam390 board from Barix. - 128MByte, DDR2, synchronous RAM 16bit databus to SDRAM interface - 128MByte, NAND Flash, 8bit databus to the NANDFlash Interface - Ethernet PHY Micrel KSZ8051R via RMII - Console on UART 0 - booting fron nand flash - spl falcon bootmode Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Tom Rini <trini@ti.com>
2013-08-15arm, da850: enable the correct uart in arch_cpu_init()Heiko Schocher
in arch_cpu_init() uart2 is fix enabled, without reference the setting from CONFIG_SYS_NS16550_COM1. Use the setting from CONFIG_SYS_NS16550_COM1 for enabling the console. Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Cc: Tom Rini <tom.rini@gmail.com> Cc: Christian Riesch <christian.riesch@omicron.at>
2013-08-15bootstage: get more BOOTSTAGE_ID* in show_boot_progress()Heiko Schocher
In case CONFIG_BOOTSTAGE is not defined, call from bootstage_mark_name() show_boot_progress(), so get more BOOTSTAGE_ID* ids in show_boot_progress() if CONFIG_BOOTSTAGE is not defined. Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Simon Glass <sjg@chromium.org> Cc: Tom Rini <trini@ti.com> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Acked-by: Simon Glass <sjg@chromium.org>
2013-08-15arm/davinci/da850: add uart0_pins_rtscts and RMII_MHz_50_CLK in ↵Heiko Schocher
emac_pins_rmii pinmux Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Tom Rini <trini@ti.com>
2013-08-15TI:armv7: Enable CONFIG_CMD_GPIOTom Rini
Add the generic "poke a GPIO" command, with the GPIO related defines. Acked-by: Dan Murphy <dmurphy@ti.com> Signed-off-by: Tom Rini <trini@ti.com>
2013-08-15TI:armv7: Enable CONFIG_CMD_SPITom Rini
Add the generic "poke the SPI bus" command, with the SPI related defines. Acked-by: Dan Murphy <dmurphy@ti.com> Signed-off-by: Tom Rini <trini@ti.com>
2013-08-15TI:omap5/dra7xx: Convert to ti_armv7_common.hTom Rini
Update omap5_common.h to use ti_armv7_common.h, and in turn update dra7xx_evm.h and omap5_uevm.h slightly. The biggest changes here are that IP blocks which exist on the platform, and had clocks enabled, now have the drivers being built as well. Signed-off-by: Tom Rini <trini@ti.com>
2013-08-15TI:am33xx: Create common config files for TI ARMv7 platforms, and AM33xxTom Rini
We create two new files, include/configs/ti_armv7_common.h for all of the common IP blocks and related features / commands we share in virtually all of our platforms. We then create include/configs/ti_am335x_common.h for everything common to the am335x SoC leaving just the board specific parts to include/configs/ti_am335x_common.h. Signed-off-by: Tom Rini <trini@ti.com>
2013-08-15am335x_evm: Bring in 'boot_fdt' logic from i.MXTom Rini
Bring in the 'boot_fdt' environment variable that i.MX boards use to try and load a device tree when booting. Signed-off-by: Tom Rini <trini@ti.com>
2013-08-15arm: spl: For Falcon Mode, set a default machid of ~0Tom Rini
With device trees, boards do not always set CONFIG_MACH_TYPE now, so we must not rely on this define being set. The kernel uses ~0 to see if we have a valid machine number or not, so set that as the default, invalid machine, id and only fix if CONFIG_MACH_TYPE is set. Acked-by: Dan Murphy <dmurphy@ti.com> Tested-by: Heiko Schocher <hs@denx.de> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Signed-off-by: Tom Rini <trini@ti.com>
2013-08-15am335x_evm: Use default baud rate tableTom Rini
Signed-off-by: Tom Rini <trini@ti.com>
2013-08-15am33xx: Stop using PHYS_DRAM_1 defineTom Rini
We defined PHYS_DRAM_1 to 0x80000000 (start of DRAM) and then used this for CONFIG_SYS_SDRAM_BASE. But then we kept on referencing PHYS_DRAM_1 in other places. Change to directly setting CONFIG_SYS_DRAM_BASE and then using that name in code. Signed-off-by: Tom Rini <trini@ti.com>
2013-08-15am33xx: CONFIG_DMA_COHERENT defines are unused, removeTom Rini
Acked-by: Dan Murphy <dmurphy@ti.com> Signed-off-by: Tom Rini <trini@ti.com>
2013-08-15OMAP3: igep00x0: allow booting with a FDT from MMCJavier Martinez Canillas
IGEP boards now have Device Tree support in the mainline kernel. To boot an IGEP board using a DT, a uEnv.txt plain text file could be used to define a custom uenvcmd that will be run by the default boot command. It is more convenient to change the default boot command to allow loading a FDT if it is stored in the boot dir of the rootfs uSD/MMC partition. If no FDT is found then the defaul command tries to boot a zImage without a DT using legacy boot. Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
2013-08-15ARM: igep00x0.h: Enable the use of CMD_EXT4, CMD_FS_GENERIC and zImage.Enric Balletbo i Serra
Able to load the kernel from some form of ext[234] or FAT. Also, with v3.9 and later of the Linux Kernel, uImage isn't builtable anymore by default, so we should switch to use the bootz command. Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
2013-08-15omap: emif: Set initial DDR PHY config firstTaras Kondratiuk
Commit "OMAP5: emif/ddr: Change emif settings as required for ES1.0 silicon" (f40107345cbcd6e0d1747eda45e76c4e2a6df0db) changed sequence to set final DDR PHY config register value at the beginning. Looks like it was made by mistake and should be reverted. Signed-off-by: Taras Kondratiuk <taras@ti.com>
2013-08-15ARM: omap24xx: remove remainders of dead boardMasahiro Yamada
Since Commit 7f5eef9 removed OMAP2420H4 support, arm1136/omap24xx has not been used at all. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-08-15ARM: omap3: Implement dpll5 (HSUSB clk) workaround for OMAP36xx/AM/DM37xx ↵Naumann Andreas
according to errata sprz318e. In chapter 'Advisory 2.1 USB Host Clock Drift Causes USB Spec Non-compliance in Certain Configurations' of the TI Errata it is recommended to use certain div/mult values for the DPLL5 clock setup. So far u-boot used the old 34xx values, so I added the errata recommended values specificly for 36xx init only. Also, the FSEL registers exist no longer, so removed them from init. Tested this on a AM3703 board with 19.2MHz oscillator, which previously couldnt lock the dpll5 (kernel complained). As a consequence the EHCI USB port wasnt usable in U-Boot and kernel. With this patch, kernel panics disappear and USB working fine in u-boot and kernel. Signed-off-by: Andreas Naumann <anaumann@ultratronik.de> [trini: Add extern to <asm/arch-omap3/clock.h> Signed-off-by: Tom Rini <trini@ti.com>
2013-08-15omap: overo: Use 200MHz SDRC timings for revision 1, 2 & 3 boardsAsh Charles
Gumstix uses 200Mhz RAM on revision 1, 2 & 3 COMs, so use 200MHz timings rather than 165MHz. Based on 6cf8bf44b1f8550e12f7f2a16e01890e5de8443d Signed-off-by: Ash Charles <ashcharles@gmail.com>
2013-08-15omap: overo: update support for Micron 1GB POPSteve Sakoman
Signed-off-by: Ash Charles <ashcharles@gmail.com>
2013-08-15ARM: IGEP0033: Remove duplicate / unused #defines.Enric Balletbo i Serra
As config was originally based on am335x_evm.h we have also some duplicate / unnused #defines. Commit 15191c91 removed these #defines on various AM335x boards but not for IGEP COM AQUILA. This patch simply removes them for this board. Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com> Reviewed-by: Javier Martinez Canillas <javier@dowhile0.org>
2013-08-15ARM: IGEP0033: Add support to boot from NAND.Enric Balletbo i Serra
Add to the default environment the possibily to boot from NAND using a ubi rootfs. Also the partition scheme is set as follows: Start Size SPL : 0x00000000 0x00080000 (512KiB) U-Boot : 0x00080000 0x00100000 (1MiB) U-Boot Env : 0x00180000 0x00020000 (128KiB) File System : 0x001C0000 - The ubiboot script gets the kernel and the dtb file from the boot directory of the File System. Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com> Reviewed-by: Javier Martinez Canillas <javier@dowhile0.org>
2013-08-15ARM: IGEP0033: Remove CYGNUS name from header.Enric Balletbo i Serra
We will not use CYGNUS names for any IGEP COM based on AM335x processor, so, to avoid confusion, remove from headers. Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com> Reviewed-by: Javier Martinez Canillas <javier@dowhile0.org>
2013-08-15ARM: IGEP0033: Add support for Flattened Device Tree.Enric Balletbò i Serra
Now, the default kernel to boot the IGEP COM AQUILA is device tree based. As old kernel is deprecated we should adapt the boot commands to use DTB files. Also, with v3.9 and later of the Linux Kernel, uImage isn't builtable anymore by default, so we should switch to use the bootz command. Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com> Reviewed-by: Javier Martinez Canillas <javier@dowhile0.org>
2013-08-15ARM: IGEP0033: Remove undef of CONFIG_CMD_MEMTESTEnric Balletbo i Serra
After commit: 79cd2f814b1c75efd47161ac27f4cbebf768240f config_cmd_default.h: Remove CONFIG_CMD_MEMTEST It's not necessary to undef the CONFIG_CMD_MEMTEST, so we can remove it from configuration file. Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com> Reviewed-by: Javier Martinez Canillas <javier@dowhile0.org>
2013-08-15ARM: AM43xx: Add config fileLokesh Vutla
Add config file Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-08-15ARM: AM43xx: Add build supportLokesh Vutla
Add AM43xx support in the required places Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-08-15ARM: OMAP: Add CONFIG_OMAP_COMMONLokesh Vutla
Adding a new CONFIG_OMAP_COMMON which is included by all boards that needs to build cpu/armv7/omap-common folder. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-08-15ARM: AM43xx: clocks: Add dpll and clock dataLokesh Vutla
Add dpll and clock data for AM43xx Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-08-15ARM: AM43xx: Add header filesLokesh Vutla
Adding the following data: -> Prcm structure -> Base addresses -> Pin mux structure. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-08-15ARM: AM43xx: Add Board filesLokesh Vutla
Add board specific information for AM43xx. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-08-15musb: Disable extra printsLokesh Vutla
There are many musb prints in SPL and U-Boot log. These prints are required only during musb debug. So replacing printk with pr_debug in musb_core. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Tested-by: Heiko Schocher <hs@denx.de> Acked-by: Heiko Schocher <hs@denx.de>
2013-08-15ARM: AM33xx: Move s_init to a common placeHeiko Schocher
s_init has the same outline for all the AM33xx based board. So making it generic. This also helps in addition of new Soc with minimal changes. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Heiko Schocher <hs@denx.de> Signed-off-by: Tom Rini <trini@ti.com> Tested-by: Heiko Schocher <hs@denx.de> Acked-by: Heiko Schocher <hs@denx.de>
2013-08-15ARM: AM33xx: Cleanup clocks layerLokesh Vutla
Cleaning up the clocks layer. This helps in addition of new Soc with minimal changes. This is derived from OMAP4 boards. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Tested-by: Heiko Schocher <hs@denx.de> Acked-by: Heiko Schocher <hs@denx.de>
2013-08-15ARM: AM33xx: Cleanup dplls dataLokesh Vutla
Locking sequence for all the dplls is same. In the current code same sequence is done repeatedly for each dpll. Instead have a generic function for locking dplls and pass dpll data to that function. This is derived from OMAP4 boards. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Tested-by: Heiko Schocher <hs@denx.de> Acked-by: Heiko Schocher <hs@denx.de>
2013-07-30gpio: omap5-uevm: Configure the tca6424 gpio expanderDan Murphy
Configure the tca6424 gpio expander This allows use of the debug and tri color LEDs. Signed-off-by: Dan Murphy <dmurphy@ti.com>
2013-07-30gpio: tca642x: Add the tca642x gpio expander driverDan Murphy
Add the tca642x gpio expander driver Datasheet: http://www.ti.com/product/tca6424a Signed-off-by: Dan Murphy <dmurphy@ti.com>
2013-07-30am335x_evm: Add am335x_boneblack variantJustin Waters
The BeagleBone Black differs from the other AM335x boards in a few significant ways, so it makes sense to create a custom configuration for it. In particular, it uses eMMC instead of NAND flash. Signed-off-by: Justin Waters <justin.waters@timesys.com>
2013-07-30am335x_evm: Add support for eMMC environmentJustin Waters
Some boards, such as the BeagleBone Black, have an eMMC chip intstead of NAND. We can use the eMMC boot partition to store the environment, since it isn't used for anything else. This allows us to have a configurable environment on those boards. Signed-off-by: Justin Waters <justin.waters@timesys.com>
2013-07-30Add additional MLO images to .gitignoreJustin Waters
This rule catches images such as MLO.byteswap Signed-off-by: Justin Waters <justin.waters@timesys.com>
2013-07-30am335x_evm: Rework bootcmd to handle two MMC devsJustin Waters
The BeagleBone Black can boot from either the MMC card or eMMC chip on board. We should try both interfaces. This modification also allows a graceful fallback if a device exists but boot images are not present on it. Changes for v2: * Fix boot partition - it should always show up as mmcblk0p2 * Fix missing FDT load Signed-off-by: Justin Waters <justin.waters@timesys.com>
2013-07-30am335x_evm: Add command line editingJustin Waters
Many modern U-Boot ports enable command line editing and a history buffer. The am335x_evm configuration is fairly comprehensive as it is, so a few extra kb should not be noticable, and it adds a very convenient feature. Signed-off-by: Justin Waters <justin.waters@timesys.com>
2013-07-30am335x_evm: Make NAND support modularJustin Waters
Give the user the ability to disable NAND support by defining CONFIG_NO_NAND. This will allow custom hardware to easily support this configuration. Signed-off-by: Justin Waters <justin.waters@timesys.com> [trini: Make apply on top of other series] Signed-off-by: Tom Rini <trini@ti.com>
2013-07-30net, phy, cpsw: fix gigabit register accessHeiko Schocher
accessing a lan9303 switch with the cpsw driver results in wrong speed detection, as the switch sets the BMSR_ERCAP in BMSR register, and follow read of the MII_STAT1000 register fails, as the switch does not support it. Current code did not check, if a phy_read() fails ... fix this. Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Joe Hershberger <joe.hershberger@gmail.com> Acked-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: Tom Rini <trini@ti.com>
2013-07-30board/ti/am335x/README: Document NOR programmingTom Rini
The Beaglebone White may be populated with a memory cape that has a NOR module. Document how to program it. Signed-off-by: Tom Rini <trini@ti.com>
2013-07-30am335x_evm: Add support to boot from NOR.Steve Kipisz
NOR requires that s_init be within the first 4KiB of the image so that we can perform the rest of the required pinmuxing to talk with the rest of NOR that we are found on. When NOR_BOOT is set we save our environment in NOR at 512KiB and a redundant copy at 768KiB. We avoid using SPL for this case and u-boot.bin is written directly to the start of NOR. We enclose the DMM-related parts of arch/arm/cpu/armv7/am33xx/emif4.c with TI81xx checks as at this time U-Boot does not discard unused sections in the main build and this code relies on functions specific to (and only provided in) ti81xx-related code. Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Signed-off-by: Steve Kipisz <s-kipisz2@ti.com> Signed-off-by: Tom Rini <trini@ti.com>
2013-07-30am335x_evm: Add support for the NOR module on the memory capeSteve Kipisz
This patch adds support for the NOR module that attaches to the memory cape for a Beaglebone board. This does not add booting support; only support so that you can boot from SD/MMC and see the NOR module so that it can be programmed. Signed-off-by: Steve Kipisz <s-kipisz2@ti.com> [trini: Clean up config changes slightly] Signed-off-by: Tom Rini <trini@ti.com>
generated by cgit v0.10.2 at 2024-08-11 17:15:07 (GMT)