summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2016-01-13spi: Remove SPI_OPM_RX_DIO|QIOFJagan Teki
SPI_OPM_RX_DIO and SPI_OPM_RX_QIOF are rx IO commands/opmodes for dual and quad. Usually IO operation's are referred to flash protocol rather with spi controller protocol, these are still present in flash side for the usage of spi-nor controllers. Cc: Simon Glass <sjg@chromium.org> Cc: Michal Simek <michal.simek@xilinx.com> Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Tested-by: Mugunthan V N <mugunthanvnm@ti.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Jagan Teki <jteki@openedev.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Signed-off-by: Jagan Teki <jteki@openedev.com>
2016-01-13spi: Remove SPI_OPM_RX_EXTNJagan Teki
SPI_OPM_RX_EXTN is a combination of all rx opmode's and spi driver shall use any one of the rx mode at a time not the combination and it is true in case of flash where spi_flash_table mention combination of supported read opmodes so-that the required one will pick based on the rx mode from spi driver. Cc: Simon Glass <sjg@chromium.org> Cc: Michal Simek <michal.simek@xilinx.com> Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Tested-by: Mugunthan V N <mugunthanvnm@ti.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Jagan Teki <jteki@openedev.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Signed-off-by: Jagan Teki <jteki@openedev.com>
2016-01-13sf: Write quad bit along with read statusJagan Teki
While setting quad bit on spansion, macronix code is writing only particular quad bit this may give wrong functionality with other register bits, So this patch fix the issue where it with write previous read reg status along particular quad bit. Cc: Vignesh R <vigneshr@ti.com> Cc: Mugunthan V N <mugunthanvnm@ti.com> Cc: Simon Glass <sjg@chromium.org> Cc: Bin Meng <bmeng.cn@gmail.com> Cc: Michal Simek <michal.simek@xilinx.com> Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Jagan Teki <jteki@openedev.com>
2016-01-13sf: Read back and check once macronix quad bit setJagan Teki
One macronix quad bit set using SR, it's good to read back and check the written bit and also if it's already been set check for the bit and return. Cc: Vignesh R <vigneshr@ti.com> Cc: Simon Glass <sjg@chromium.org> Cc: Bin Meng <bmeng.cn@gmail.com> Tested-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: Jagan Teki <jteki@openedev.com>
2016-01-13sf: Read back and check once spansion quad bit setJagan Teki
One spansion quad bit set using CR, it's good to read back and check the written bit and also if it's already been set check for the bit and return. Cc: Vignesh R <vigneshr@ti.com> Cc: Simon Glass <sjg@chromium.org> Cc: Bin Meng <bmeng.cn@gmail.com> Cc: Michal Simek <michal.simek@xilinx.com> Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Tested-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: Jagan Teki <jteki@openedev.com>
2016-01-13sf: Fix quad bit set for micron devicesJagan Teki
Setting up quad bit for micron devices need to do the same way as other flash devices like spansion, winbond etc does using enhanced volatile config register so this patch adds this support instead of printing "QEB is volatile" Cc: Simon Glass <sjg@chromium.org> Cc: Bin Meng <bmeng.cn@gmail.com> Cc: Peter Pan <peterpandong@micron.com> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Michal Simek <michal.simek@xilinx.com> Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Jagan Teki <jteki@openedev.com>
2016-01-13sf: Use BIT macroJagan Teki
Used BIT macro like 1 << nr as BIT(nr) where nr is 0...n Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Signed-off-by: Jagan Teki <jteki@openedev.com>
2016-01-13sf: Minor cleanupJagan Teki
- Tab space - Place all read commands at one place. - Re-arrange write commands. Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Signed-off-by: Jagan Teki <jteki@openedev.com>
2016-01-13sf: Remove spi_flash_removeJagan Teki
Use direct call to device_remove instead of exctra spi_flash_remove defination. Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Jagan Teki <jteki@openedev.com>
2016-01-13sf: Rename bank_end to bar_end in read_barJagan Teki
bar_end gives more meaningfull compared to bank_end and spi_flash_write_bar uses bar_end so replaced bank_end with bar_end in spi_flash_read_bar Signed-off-by: Jagan Teki <jteki@openedev.com>
2016-01-13sf: Rename spi_flash_set_* functionsJagan Teki
Since quad_mode functions are local to spi flash core, rename them to a meaningful and readable names. Signed-off-by: Jagan Teki <jteki@openedev.com>
2016-01-13sf: Move spi_read_cmds_array locallyJagan Teki
Since spi_read_cmds_array is used locally in spi_flash_scan, so move array to locally used function instead of defining global array. Tested-by: Jagan Teki <jteki@openedev.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Signed-off-by: Jagan Teki <jteki@openedev.com>
2016-01-13spi: Rename SPI_TX_BP|QPP to SPI_TX_BYTE|QUADJagan Teki
Since SPI_TX_* are spi_slave{} members so use spi protocol notation instead spi flash programming, like SPI_TX_BP => SPI_TX_BYTE SPI_TX_QPP => SPI_TX_QUAD Cc: Simon Glass <sjg@chromium.org> Tested-by: Jagan Teki <jteki@openedev.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Signed-off-by: Jagan Teki <jteki@openedev.com>
2016-01-13spi: Use mode instead of op_mode_txJagan Teki
Used mode member from spi_slave{} instead of op_mode_tx. Cc: Simon Glass <sjg@chromium.org> Tested-by: Jagan Teki <jteki@openedev.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Signed-off-by: Jagan Teki <jteki@openedev.com>
2016-01-13spi: make mode visible to both dm and non-dmJagan Teki
Couldn't find the exact reason to define 'mode' for dm, probably it is not using in non-dm drivers but it need to visible both dm and non-dm as mode data is getting dereferred in spi flash core ie common to both. Cc: Simon Glass <sjg@chromium.org> Tested-by: Jagan Teki <jteki@openedev.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Signed-off-by: Jagan Teki <jteki@openedev.com>
2016-01-13sf: Get spi locally from spi_flashJagan Teki
For better code readabilty, get the spi pointer from spi_flash{} locally and use it instead of direct dereferring spi pinter as flash->spi->* Tested-by: Jagan Teki <jteki@openedev.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Signed-off-by: Jagan Teki <jteki@openedev.com>
2016-01-12Merge git://git.denx.de/u-boot-dmTom Rini
2016-01-12sandbox: eth-raw-os.c: Ensure that our interface name is not too longTom Rini
Coverity notes that we do not ensure when we copy ifname we still have space left to ensure NULL termination. As cannot control the size of ifr_name we must make sure that our argument will not overflow the buffer. Reported-by: Coverity (CID 131094) Cc: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2016-01-12dm: core: Add option to configure an offset for the address translationStefan Roese
Some platforms need to ability to configure an offset to the standard addresses extracted from the device-tree. This patch allows this by adding a function to DM to configure this offset (if needed). Signed-off-by: Stefan Roese <sr@denx.de> Acked-by: Simon Glass <sjg@chromium.org> Cc: Simon Glass <sjg@chromium.org> Fixed space before tab: Signed-off-by: Simon Glass <sjg@chromium.org>
2016-01-12rockchip: Use the debug UART on rk3036Simon Glass
Rather than using a new debug UART implementation, use the standard one provided by U-Boot. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Thomas Chou <thomas@wytron.com.tw>
2016-01-12dm: ns16550: Allow the driver to be omitted if requestedSimon Glass
Allow the ns16550 debug UART to be used without the full driver. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Thomas Chou <thomas@wytron.com.tw>
2016-01-12dm: serial: Allow the UART driver to be dropped from the imageSimon Glass
In very very space-constrained devices even the full UART driver is too large. In this case the debug UART can still be used in some cases. Add options to enable the UART driver in SPL and U-Boot proper. Enable both options by default. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Thomas Chou <thomas@wytron.com.tw>
2016-01-12dm: net: usb: Convert mcs7830 driver to support driver modelSimon Glass
Adjust this driver to support driver model for Ethernet. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-12dm: net: usb: Refactor mcs7830 driver ready for DM conversionSimon Glass
Remove stamp data and create common functions for the main Ethernet operations. This will make it easier to convert this driver to support driver model. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-12pci: Tidy up comments in pci_bind_bus_devices()Simon Glass
The current comments are confusing. We don't actually bind a generic device when the device tree has no information. We try to scan available PCI drivers. Update the comments to reflect this. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-01-12dm: Convert PCI MMC over to use DM PCI APISimon Glass
At present pci_mmc_init() does not correctly use the PCI function since the list it passes is not terminated. The array size passed to pci_mmc_init() is actually not used correctly. Fix this and adjust the pci_mmc_init() to scan all available MMC devices. Adjust this code to use the new driver model PCI API. This should move over to the new MMC uclass at some point. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-01-12dm: usb: Convert echi-pci to use new DM PCI APISimon Glass
Convert this driver to use the new driver model PCI API. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Marek Vasut <marex@denx.de>
2016-01-12dm: ahci: Convert to use new DM PCI APISimon Glass
Convert this driver to use the new driver model PCI API. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-01-12dm: pci: Switch to DM API for PCI address mappingSimon Glass
We should use the new address mapping functions unless we are in compatibility mode. Disable the old functions by default. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-01-12dm: net: Convert rtl8169 to use DM PCI APISimon Glass
Update this driver to use the proper driver-model PCI API functions. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-12dm: pci: Add driver model API functions for address mappingSimon Glass
At present the PCI address map functions use the old API. Add new functions for this so that drivers can be converted. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-01-12dm: test: Convert PCI tests to use the DM PCI APISimon Glass
Update these tests to use driver model API functions. Signed-off-by: Simon Glass <sjg@chromium.org>
2016-01-12dm: tegra: net: Convert tegra boards to driver model for EthernetSimon Glass
Adjust all Tegra boards to use driver model for Ethernet, now that the required drivers are converted. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-12dm: pci: Drop the old version of pci_find_class()Simon Glass
Move this function into the compatibility file so that it is not available by default. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-01-12dm: pci: Drop the old version of pci_find_device/s()Simon Glass
Move these functions into the compatibility file so that they are not available by default. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-01-12dm: x86: pci: Adjust bios_run_on_x86() to use the DM PCI APISimon Glass
This function should take a struct udevice rather than pci_dev_t. Update it. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com>
2016-01-12dm: pci: video: Convert video and pci_rom to use DM PCI APISimon Glass
Adjust these files to use the driver-model PCI API instead of the legacy functions. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Anatolij Gustschin <agust@denx.de> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com>
2016-01-12dm: Convert bios_interrupts to use DM PCI APISimon Glass
Adjust this code to use driver model for devices where possible. Since existing users have not been converted the old code must remain. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com>
2016-01-12dm: x86: ivybridge: Convert graphics init to use DM PCI APISimon Glass
Use the driver-model PCI functions here where possible. For now we have to search for the device with pci_bus_find_bdf() but at some point we can put this in a proper driver and avoid this. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-01-12dm: serial: Convert ns16550 driver to use driver model PCI APISimon Glass
Use the driver model version of the function to find the BAR. This updates the fdtdec function, of which ns16550 is the only user. The fdtdec_get_pci_bdf() function is dropped for several reasons: - with driver model we should use 'struct udevice *' rather than passing the device tree offset explicitly - there are no other users in the tree - the function parses for information which is already available in the PCI device structure (specifically struct pci_child_platdata which is available at dev_get_parent_platdata(dev) Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com>
2016-01-12dm: pci: Add a function to read a PCI BARSimon Glass
Add a driver-model function for reading the PCI BAR from a device. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-01-12dm: pci: Add a driver-model version of pci_find_class()Simon Glass
Add a function which scans the driver model device information rather than scanning the PCI bus again. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com>
2016-01-12dm: pci: scsi: Use driver-model PCI APISimon Glass
Adjust the SCSI command to use driver model for its PCI interface. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com>
2016-01-12dm: pci: Add a driver-model version of pci_find_device()Simon Glass
Add a function which scans the driver model device information rather than scanning the PCI bus again. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com>
2016-01-12dm: pci: Use driver model PCI API in auto-configSimon Glass
At present we are using legacy functions even in the auto-configuration code used by driver model. Add a new pci_auto.c version which uses the correct API. Create a new pci_internal.h header to hold functions that are used within the PCI subsystem, but are not exported to other drivers. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com>
2016-01-12dm: pci: Add a dm_ prefix to pci_bus_find_bdf()Simon Glass
Most driver model PCI functions have a dm_ prefix. At some point, when the old code is converted to driver model and the old functions are removed, we will drop that prefix. For consistency, we should use the dm_ prefix for all driver model functions. Update pci_bus_find_bdf() accordingly. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-01-12dm: pci: Add a dm_ prefix to pci_get_bdf()Simon Glass
Most driver model PCI functions have a dm_ prefix. At some point, when the old code is converted to driver model and the old functions are removed, we will drop that prefix. For consistency, we should use the dm_ prefix for all driver model functions. Update pci_get_bdf() accordingly. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-01-12dm: pci: Mark legacy files as suchSimon Glass
We don't want people changing the legacy PCI files while migration is in progress. Update the file headers to indicate that. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-01-12ARM: uniphier: fix recommended board setting in documentMasahiro Yamada
The mem_is_flash() in arch/arm/mach-uniphier/micro-support_card.c writes/reads the tail of each NOR flash bank to check if the device really resides there. If CS1_SPLIT were enabled, the support card would always require two NOR flash devices to be inserted for the correct NOR detection. This is not probably what we want. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-01-12ARM: uniphier: add dump command for DDR Multi PHY registersMasahiro Yamada
The ProXstream2/PH1-LD6b is integrated with a new IP for DDR PHY which is not register-compatible with the former SoCs. Add a new command to support the register dump of this IP. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
generated by cgit v0.10.2 at 2024-11-16 18:16:01 (GMT)