summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2012-05-15mx6qsabrelite: Allow booting a zImage kernelFabio Estevam
Allow booting a zImage kernel. Cc: Jason Liu <r64343@freescale.com> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-05-15mx28evk: Allow booting a zImage kernelFabio Estevam
Allow booting a zImage kernel. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-05-15m28evk: Allow to booting a dt kernelFabio Estevam
Allow to booting a dt kernel. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-05-15mx28evk: Allow to booting a dt kernelFabio Estevam
Allow to booting a dt kernel. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-05-15mx6qsabrelite: No need to set the direction for GPIO3_23 againFabio Estevam
There is a 'gpio_direction_output(87, 0);' call previously, so the GPIO direction is already established. Use gpio_set_value() for changing the GPIO output then. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Dirk Behme <dirk.behme@googlemail.com>
2012-05-15pmic: Add support for the Dialog DA9053 PMICFabio Estevam
Add support for the Dialog DA9053 PMIC. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-05-15MX53: mx53loco: Add SATA supportStefano Babic
Signed-off-by: Stefano Babic <sbabic@denx.de> CC: Jason Liu <jason.hui@linaro.org> Acked-by: Jason Liu <jason.hui@linaro.org>
2012-05-15MX53: Add support to ESG ima3 boardStefano Babic
The ESG ima3-mx53 board is based on the Freescale i.MX53 SOC. It boots from NOR (128 MB) and supports Ethernet (FEC), SATA. Signed-off-by: Stefano Babic <sbabic@denx.de>
2012-05-15SATA: add driver for MX5 / MX6 SOCsStefano Babic
This driver is part of Freescale's LTIB for MX5 / MX6. Signed-off-by: Stefano Babic <sbabic@denx.de> Signed-off-by: Terry Lv <r65388@freescale.com> CC: Fabio Estevam <fabio.estevam@freescale.com> CC: Dirk Behme <dirk.behme@de.bosch.com>
2012-05-15MX53: add function to set SATA clock to internalStefano Babic
The MX53 SATA interface can use an internal clock (USB PHY1) instead of an external clock. This is an undocumented feature, but used on most Freescale's evaluation boards, such as MX53-loco. As stated by Freescale's support: Fuses (but not pins) may be used to configure SATA clocks. Particularly the i.MX53 Fuse_Map contains the next information about configuring SATA clocks : SATA_ALT_REF_CLK[1:0] (offset 0x180C) '00' - 100MHz (External) '01' - 50MHz (External) '10' - 120MHz, internal (USB PHY) '11' - Reserved Signed-off-by: Stefano Babic <sbabic@denx.de> CC: Fabio Estevam <fabio.estevam@freescale.com>
2012-05-15SATA: check for return value from sata functionsStefano Babic
sata functions are called even if previous functions failed because return value is not checked. Signed-off-by: Stefano Babic <sbabic@denx.de> CC: Dirk Behme <dirk.behme@de.bosch.com> CC: Fabio Estevam <fabio.estevam@freescale.com>
2012-05-15MX5: Add definitions for SATA controllerStefano Babic
Add base address and MXC_SATA_CLK to return the clock used for the SATA controller. Signed-off-by: Stefano Babic <sbabic@denx.de> CC: Fabio Estevam <fabio.estevam@freescale.com> CC: Dirk Behme <dirk.behme@de.bosch.com>
2012-05-15NET: fec_mxc.c: Add a way to disable auto negotiationStefano Babic
Signed-off-by: Stefano Babic <sbabic@denx.de> CC: Fabio Estevam <fabio.estevam@freescale.com>
2012-05-15Define UART4 and UART5 base addressesStefano Babic
Signed-off-by: Stefano Babic <sbabic@denx.de>
2012-05-15EXYNOS: Change bits per pixel value proper for u-boot.Donghwa Lee
vl_bpix of vidinfo_t was changed proper value for u-boot. It is used to multiple of 2 by using NBITS() macro. Signed-off-by: Donghwa Lee <dh09.lee@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Anatolij Gustschin <agust@denx.de> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2012-05-15EXYNOS: support TRATS board display functionDonghwa Lee
This patch support TRATS board configuration and display function. Signed-off-by: Donghwa Lee <dh09.lee@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Inki Dae <inki.dae@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2012-05-15LCD: support S6E8AX0 amoled driver based on EXYNOS MIPI DSIDonghwa Lee
This patch support S6E8AX0 amoled driver based on EXYNOS MIPI DSI interface. Signed-off-by: Donghwa Lee <dh09.lee@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Inki Dae <inki.dae@samsung.com> Acked-by: Anatolij Gustschin <agust@denx.de>
2012-05-15EXYNOS: support EXYNOS MIPI DSI interface driver.Donghwa Lee
EXYNOS SoC platform has MIPI-DSI controller and MIPI-DSI based LCD Panel could be used with it. This patch supports MIPI-DSI driver based Samsung SoC chip. LCD panel driver based MIPI-DSI should be registered to MIPI-DSI driver at board file and LCD panel driver specific function registered to mipi_dsim_ddi structure at lcd panel init function called system init. In the MIPI-DSI driver, find lcd panel driver by using registered lcd panel name, and then initialize lcd panel driver. Signed-off-by: Donghwa Lee <dh09.lee@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Inki Dae <inki.dae@samsung.com> Acked-by: Anatolij Gustschin <agust@denx.de>
2012-05-15EXYNOS: support EXYNOS framebuffer and FIMD display drivers.Donghwa Lee
This patch support EXYNOS FB and FIMD display drivers. Signed-off-by: Donghwa Lee <dh09.lee@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Inki Dae <inki.dae@samsung.com> Acked-by: Anatolij Gustschin <agust@denx.de>
2012-05-15LCD: add data structure for EXYNOS display driverDonghwa Lee
Add vidinfo data structure for EXYNOS display driver Signed-off-by: Donghwa Lee <dh09.lee@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Inki Dae <inki.dae@samsung.com> Acked-by: Anatolij Gustschin <agust@denx.de>
2012-05-15EXYNOS: add LCD and MIPI DSI clock interface.Donghwa Lee
To sets up lcd and mipi clock in EXYNOS display driver, added clock interface. Signed-off-by: Donghwa Lee <dh09.lee@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Inki Dae <inki.dae@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2012-05-15EXYNOS: definitions of system resgister and power management registers.Donghwa Lee
This is definitions of system registers and power mananagement registers for EXYNOS SoC. Signed-off-by: Donghwa Lee <dh09.lee@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Inki Dae <inki.dae@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2012-05-15SMDK5250: fix compiler warningMinkyu Kang
this patch fixed following warning. tzpc_init.c: In function 'tzpc_init': tzpc_init.c:35: warning: assignment from incompatible pointer type Signed-off-by: Minkyu Kang <mk7.kang@samsung.com> Cc: Chander Kashyap <chander.kashyap@linaro.org>
2012-05-15misc:pmic:samsung Convert TRATS target to use MAX8997 instead of MAX8998Łukasz Majewski
TRATS target uses MAX8997 PMIC device instead of MAX8998. Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Minkyu Kang <mk7.kang@samsung.com>
2012-05-15misc:pmic:max8997 MAX8997 support for PMIC driverŁukasz Majewski
This commit adds support for MAX8997 PMIC driver. Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Stefano Babic <sbabic@denx.de>
2012-05-15TRATS: modify the trats's configurationJaehoon Chung
Trats is supported 1GiB memory size. (Each bank size is 512MB.) And INITRD is unnecessary. So removed them. Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2012-05-15ARM: Exynos4: ADC: Universal_C210: Enable LDO4 power line for ADC measurementŁukasz Majewski
This patch enables LDO4 power line for preparing proper voltages to be measured by ADC converter. This measurement is used for determination of target board HW revision. Test HW: Universal_C210 (Exynos4210) rev. 0.0 Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Cc: Minkyu Kang <mk7.kang@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2012-05-15EXYNOS: Rename exynos5_tzpc structure to exynos_tzpcChander Kashyap
TZPC IP is common across Exynos based SoC'c. Renaming exynos5_tzpc in arch/arm/include/asm/arch-exynos/tzpc.h to exynos_tzpc will allow generic usase of tzpc. Also modify board/samsung/smdk5250/tzpc_init.c to use exynos_tzpc. Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2012-05-15arm: ea20: Change macro from BOARD_LATE_INIT to CONFIG_BOARD_LATE_INITNobuhiro Iwamatsu
With almost all the architecture and board BOARD_LATE_INIT does not use. CONFIG_BOARD_LATE_INIT is used instead. This changed CONFIG_BOARD_LATE_INIT from BOARD_LATE_INIT. Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> CC: Stefano Babic <sbabic@denx.de> Acked-by: Stefano Babic <sbabic@denx.de>
2012-05-15arm: cam_enc_4xx: Change macro from BOARD_LATE_INIT to CONFIG_BOARD_LATE_INITNobuhiro Iwamatsu
With almost all the architecture and board BOARD_LATE_INIT does not use. CONFIG_BOARD_LATE_INIT is used instead. This changed CONFIG_BOARD_LATE_INIT from BOARD_LATE_INIT. Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> CC: Heiko Schocher <hs@denx.de> Acked-by: Heiko Schocher <hs@denx.de>
2012-05-15cm-t35: add I2C multi-bus supportNikita Kiryanov
Enable I2C multi-bus support and config I2C muxes for I2C2 and I2C3. Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
2012-05-15include/configs: Remove CONFIG_SYS_64BIT_STRTOULTom Rini
This define does not control anything, remove it. Signed-off-by: Tom Rini <trini@ti.com>
2012-05-15include/configs: Remove CONFIG_SYS_64BIT_VSPRINTFTom Rini
This define does not control anything, remove it. Signed-off-by: Tom Rini <trini@ti.com>
2012-05-15omap3: Introduce weak misc_init_rTom Rini
Introduce a __weak misc_init_r function that just runs dieid_num_r(). Remove misc_init_r from cm_t35, mcx, omap3_logic and mt_ventoux as this was all they did for misc_init_r. Cc: Igor Grinberg <grinberg@compulab.co.il> Cc: Ilya Yanok <yanok@emcraft.com> Cc: Peter Barada <peter.barada@logicpd.com> Cc: Stefano Babic <sbabic@denx.de> Signed-off-by: Tom Rini <trini@ti.com> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
2012-05-15omap730p2: Remove empty misc_init_rTom Rini
We had a do-nothing misc_init_r, remove along with CONFIG_MISC_INIT_R Signed-off-by: Tom Rini <trini@ti.com>
2012-05-15omap5912osk: Remove empty misc_init_rTom Rini
We had a do-nothing misc_init_r, remove along with CONFIG_MISC_INIT_R Signed-off-by: Tom Rini <trini@ti.com>
2012-05-15omap4+: Remove CONFIG_ARCH_CPU_INITTom Rini
OMAP4/5 had an empty arch_cpu_init() so drop that along with CONFIG_ARCH_CPU_INIT Signed-off-by: Tom Rini <trini@ti.com>
2012-05-15omap4: Remove CONFIG_SYS_MMC_SET_DEVTom Rini
This is only used on !CONFIG_GENERIC_MMC which is false here. Signed-off-by: Tom Rini <trini@ti.com>
2012-05-15OMAP3: pandora: drop console kernel argumentGrazvydas Ignotas
As ttyS0 is no longer valid for newer OMAP kernels, and pandora serial cables are not widespread, simply drop console argument. This should allow booting old and new kernels with default arguments, and those who need serial can use a boot script on SD card. Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
2012-05-15OMAP3: pandora: revise GPIO configurationGrazvydas Ignotas
Update pandora's GPIO setup code with these changes: - convert to gpiolib - set up dual voltage GPIOs to match supply of 1.8V by clearing VMODE1 - add GPIO_IO_PWRDNZ configuration for DM3730 variation of pandora (required to enable GPIO 126, 127, and 129 I/O cells in DM3730) - add wifi reset pulse as recommended by wifi chip's manufacturer - drop configuration of GPIOs that u-boot doesn't need Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
2012-05-15OMAP3: pandora: pin mux updates for DM3730 board variantGrazvydas Ignotas
DM3730 needs some additional pin mux configuration for GPIOs 126-129 to work, add it. Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
2012-05-15Makefile: Add a 'checkthumb' ruleTom Rini
This rule confirms that if we're on ARM and we have enabled THUMB builds that we have a new enough toolchain to produce a working binary. Changes in v2: - Switch to ALL-$(CONFIG_SYS_THUMB_BUILD) in arch/arm/config.mk (Mike F) - Simplfy checkthumb test after doing the above Signed-off-by: Tom Rini <trini@ti.com> Acked-by: Mike Frysinger <vapier@gentoo.org>
2012-05-15tools, config.mk: Add gcc-version.sh, cc-version test from LinuxTom Rini
Added from Linux - commit fde7d9049e55ab85a390be7f415d74c9f62dd0f9 Signed-off-by: Tom Rini <trini@ti.com>
2012-05-15OMAP4: enable Thumb buildAneesh V
Signed-off-by: Aneesh V <aneesh@ti.com>
2012-05-15omap4+: Avoid using __attribute__ ((__packed__))Aneesh V
Avoid using __attribute__ ((__packed__)) unless it's absolutely necessary. "packed" will remove alignment requirements for the respective objects and may cause alignment issues unless alignment is also enforced using a pragma. Here, these packed attributes were causing alignment faults in Thumb build. Signed-off-by: Aneesh V <aneesh@ti.com>
2012-05-15armv7: Use -march=armv7-a and thereby enable Thumb-2Aneesh V
Enable -march=armv7-a for armv7 platforms if the tool-chain supports it. This in turn results in Thumb-2 code generated for these platforms if CONFIG_SYS_THUMB_BUILD is enabled. Signed-off-by: Aneesh V <aneesh@ti.com>
2012-05-15ARM: enable Thumb buildAneesh V
Enable Thumb build and ARM-Thumb interworking based on the new config flag CONFIG_SYS_THUMB_BUILD Signed-off-by: Aneesh V <aneesh@ti.com> Acked-by: Mike Frysinger <vapier@gentoo.org>
2012-05-15armv7: add appropriate headers for assembly functionsAneesh V
Use ENTRY and ENDPROC with assembly functions to ensure necessary assembler directives for all functions. Signed-off-by: Aneesh V <aneesh@ti.com> Acked-by: Mike Frysinger <vapier@gentoo.org>
2012-05-15arm: adapt asm/linkage.h from LinuxAneesh V
This will add ARM specific over-rides for the defines from linux/linkage.h Signed-off-by: Aneesh V <aneesh@ti.com> Tested-by: Mike Frysinger <vapier@gentoo.org>
2012-05-15OMAP5: reset: Use cold reset in case of 5430ES1.0SRICHARAN R
Warm reset is not functional in case of omap5430ES1.0. So override the weak reset_cpu function to use cold reset instead. Signed-off-by: R Sricharan <r.sricharan@ti.com>
generated by cgit v0.10.2 at 2024-08-12 16:22:04 (GMT)