Age | Commit message (Collapse) | Author |
|
This patch adds the support for VID on LS1088AQDS and LS1088ARDB systems.
It reads the fusesr register and changes the VDD accordingly by adjusting the
voltage via LTC3882 regulator.
This patch also takes care of the special case of 0.9V VDD is present in
fusesr register. In that case,it also changes the SERDES voltage by disabling
the SERDES, changing the SVDD and then re-enabling SERDES.
Signed-off-by: Raghav Dogra <raghav.dogra@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Amrita Kumari <amrita.kumari@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
|
|
Restructures common driver to support LTC3882 voltage regulator
chip.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
|
|
Adds below LTC3882 voltage regulator config:
CONFIG_VOL_MONITOR_LTC3882_READ
CONFIG_VOL_MONITOR_LTC3882_SET
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
|
|
Moves IR chip (IR36021) specific code in flag to resolve
compilation issue where it is not present. For example,
LS1088A is having a new LTC3882 voltage chip.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
|
|
Adds a board specific API namely board_adjust_vdd which
is required to define the board VDD adjust settings.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
|
|
Adds below voltage values supported by LS1088A Soc:
1.025 V(default), 0.9875V, 0.9750 V, 0.9V, 1.0 V, 1.0125 V, 1.0250 V
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
|
|
Adds SERDES voltage and reset SERDES lanes API and makes
enable/disable DDR controller support 0.9V API common.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
|
|
According current code base, CONFIG_LS1012A should be
CONFIG_ARCH_LS1012A, or function fsl_fdt_disable(blob) will be
wrongly called to disable all dwc3 USB nodes on LS1012A, which
cause Linux USB function stop working at all.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
|
|
Enable validation of boot.scr script prior to its execution dependent
on "secureboot" flag in environment. Enable fall back option to
qspi boot in case of secure boot. Also enable "secureboot=y" flag
in environment for ARM based platforms instead of bootcmd.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Tested-by: Vinitha Pillai <vinitha.pillai@nxp.com>
|
|
Enable validation of boot.scr script prior to its execution dependent
on "secureboot" flag in environment. Enable fall back option to
nor/qspi boot in case of secure boot. Also enable "secureboot=y"
flag in environment for ARM based platforms instead of bootcmd.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Tested-by: Vinitha Pillai <vinitha.pillai@nxp.com>
|
|
The SP805-WDT module on LS1088A requires configuration of PMU's
PCTBENR register to enable watchdog counter decrement and reset
signal generation. The watchdog clock needs to be enabled first.
Signed-off-by: Zhang Ying-22455 <ying.zhang22455@nxp.com>
|
|
SEC must be initialised before PPA is validated, so
call sec_init() ahead of ppa_init().
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
|
|
Adds config CONFIG_FSL_LS_PPA and CONFIG_FSL_CAAM in
LS2080AQDS and LS2080ARDB secure boot defconfig.
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
|
|
Add the secure boot defconfigs for QSPI boot on LS1088ARDB
and LS1088AQDS platforms.
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
|
|
Validates PPA, MC, DPC, Bootscript, DPL and Kernel images in ESBC phase
using esbc_validate command. Add images validation in default environment
under mcinitcmd prior to MC initialization.
Add header address for PPA to be validated during ESBC phase for LS1088A
platform based on LAyerscape Chasis 3.
Moves sec_init prior to ppa_init as for validation of PPA sec must
be initialised before the PPA is initialised.
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
|
|
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
|
|
Using changes in this patch we were able to reduce approx 8k
size of u-boot-spl.bin image. Following is breif description of
changes to reduce SPL size:
1. Changes in board/freescale/ls1088a/Makefile to remove
compilation of eth.c and cpld.c in case of SPL build.
2. Changes in board/freescale/ls1088a/ls1088a.c to keep
board_early_init_f funcations in case of SPL build.
3. Changes in ls1088a_common.h & ls1088ardb.h to remove driver
specific macros due to which static data was being compiled in
case of SPL build.
4. Enable CONFIG_SYS_DCACHE_OFF in case of SPL build as DCACHE is
not being enabled in case of SPL image but was compiled in to
add redundant code.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com
|
|
Using changes in this patch we were able to reduce approx 4k
size of u-boot-spl.bin image. Following is breif description of
changes to reduce SPL size:
1. Compile-off mp.c and libfdt.c in case of SPL build.
2. Keep MMU and DCACHE specific variable and functions under
CONFIG_SYS_DCACHE_OFF macro.
3. Compile-off IFC specific funtion call "init_early_memctl_regs"
in case of SPL build.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
|
|
Tested on ls1088ardb with automatically boot Ubuntu from SD
card or USB disk, if it fails to detect external storage disk,
fall back to qspi/sd boot.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Zhang Ying <zhangying@nxp.com>
|
|
As part of chain of trust with confidentiality along with distro
boot, linux kernel image needs to be stored in encrypted form on
ext4 boot partition. So enable CONFIG_CMD_EXT4_WRITE in case of
Secure boot.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
|
|
Signed-off-by: Amrita Kumari <amrita.kumari@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
|
|
Signed-off-by: Amrita Kumari <amrita.kumari@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
|
|
Signed-off-by: Amrita Kumari <amrita.kumari@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
|
|
Signed-off-by: Amrita Kumari <amrita.kumari@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
|
|
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Amrita Kumari <amrita.kumari@nxp.com>
|
|
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Amrita Kumari <amrita.kumari@nxp.com>
|
|
As per current implemenetation, default value of board env is
based on board filename i.e ls2080ardb.
With distro support changes, this env is used to decide upon
kernel dtb which is different for other SoCs (ls2088a, ls2081a)
combination supported with this board.
Add support to modify board env based on SoC type
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
It is recommended to check either controller is free to take
new spi action. The IP_ACC and AHB_ACC bits indicates that
the controller is busy in IP or AHB mode respectively.
And the BUSY bit indicates that controller is currently
busy handling a transaction to an external flash device
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
|
|
For some special reset times for longer pcie devices, in this case, the
pcie device may on polling compliance state, the RC considers the pcie
device is link up, but the pcie device is not link up, only the L0 state
is link up state. So add the link up status judgement mechanisms.
Signed-off-by: Bao Xiaowei <xiaowei.bao@nxp.com>
|
|
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
|
|
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
|
|
Concatenation of u-boot-spl.bin and u-boot.img for NXP layerscape
platform SoC: LS1088A/LS2080A and their variants
This patch also depricates UBOOT_BINLOAD in favour of SPL_PAYLOAD
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
|
|
EC1 and EC2 are RGMII interface on ls1088aqds platform.
This patch add support of RGMII with PHY and MDIO
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Amrita Kumari <amrita.kumari@nxp.com>
|
|
This patch adds support RGMII protocol
NXP's LDPAA2 support RGMII protocol. LS1088A is the
first Soc supporting both RGMII and SGMII.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Amrita Kumari <amrita.kumari@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
|
|
Even after memory free of phydev, priv is still pointing to the
obsolete address.
So update priv->phydev as NULL after memory free.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
|
|
This patch add support of LS1088AQDS platform.
The LS1088A QorIQTM Development System (QDS) is a
high-performance computing, evaluation, and
development platform that supports the LS1088A QorIQ Architecture
processor.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
|
|
LS1088A is an ARMv8 implementation. The LS1088ARDB is an evaluatoin
platform that supports the LS1088A family SoCs. This patch add basic
support of the platform.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Raghav Dogra <raghav.dogra@nxp.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
|
|
The QorIQ LS1088A processor is built on the Layerscape
architecture combining eight ARM A53 processor cores
with advanced, high-performance datapath acceleration
and networks, peripheral interfaces required for
networking, wireless infrastructure, and general-purpose
embedded applications.
LS1088A is compliant with the Layerscape Chassis Generation 3.
Features summary:
- Eight 32-bit / 64-bit ARM v8 Cortex-A53 CPUs
- Cores are in 2 cluster of 4-cores each
- Cache coherent interconnect (CCI-400)
- One 64-bit DDR4 SDRAM memory controller with ECC
- Data path acceleration architecture 2.0 (DPAA2)
- Ethernet interfaces: SGMIIs, RGMIIs, QSGMIIs, XFIs
- QSPI, IFC, 3 PCIe, 1 SATA, 2 USB, 1 SDXC, 2 DUARTs etc
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Raghav Dogra <raghav.dogra@nxp.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
|
|
It is not necessary for every SoC to have 2 SATA controller.
So put SATA1, SATA2 code under respective defines.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
|
|
LS2080 family has CCN-504 cache coherent interconnet.
Other SoCs from LSCH3 may have differnt interconnect like
LS1088.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
|
|
This config is depricated and new config SYS_CCI400_OFFSET
is introduced in Kconfig
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
|
|
CoreLink Cache Coherent Interconnect (CCI) is ARM BUS which
provides full cache coherency between two clusters of multi-core
CPUs and I/O coherency for devices and I/O masters.
This patch add new CONFIG defination "FSL_SYS_HAS_CCI400" and
removes register space definaton of CCI-400 bus from
immap_ls102xa to fsl_immap, since same is defined there already
"CONFIG_SYS_CCI400_ADDR" is depricated and new SYS_CCI400_OFFSET
is introduced in Kconfig
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
|
|
CoreLink Cache Coherent Interconnect (CCI) is ARM BUS which
provides full cache coherency between two clusters of multi-core
CPUs and I/O coherency for devices and I/O masters.
This patch add new CONFIG defination "SYS_FSL_HAS_CCI400" and
moves existing register space definaton of CCI-400 bus
from immap_lsch2 to fsl_immap, so that it can be used
for both chasis 2 and chasis 3.
"CONFIG_SYS_CCI400_ADDR" is depricated and new SYS_CCI400_OFFSET
is introduced in Kconfig
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
|
|
The old logic always enabled the TX-delay when the phy-mode was set to
PHY_INTERFACE_MODE_RGMII. With this patch we enable the TX delay for
PHY_INTERFACE_MODE_RGMII_ID and PHY_INTERFACE_MODE_RGMII_TXID and
disable it for PHY_INTERFACE_MODE_RGMII.
Based on a similar change made in the Linux Realtek PHY driver
by Martin Blumenstingl <martin.blumenstingl@googlemail.com>.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: York Sun <york.sun@nxp.com>
|
|
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: York Sun <york.sun@nxp.com>
|
|
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
|
|
Include common config_distro_defaults.h and config_distro_bootcmd.h
for u-boot enviroments to support automatical distro boot which
scan boot.scr from external storage devices(e.g. SD/USB/SATA/SCSI disk)
and execute autoboot script. Tested on ls1043ardb with automatically
boot Ubuntu from SD card or USB disk, if it fails to detect external
storage disk, fall back to nor/qspi boot.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Signed-off-by: Zhang Ying <ying.zhang22455@nxp.com>
|
|
In fsl_mc_ldpaa_exit(), in case of mc is booted and
dpl is applied, it should return earlier without executing
dpbp_exit()
Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
Acked-by: Priyanka Jain <priyanka.jain@nxp.com>
Acked-by: Yogesh Narayan Gaur <yogeshnarayan.gaur@nxp.com>
|
|
Increase env sector size from 64kb to 256kb for qspi boot
Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
|