| Age | Commit message (Collapse) | Author |
|---|
|
xHCI spec says: the values of the 'route string' field shall be
initialized by the first 'Address Device' command issued to a
device slot, and shall not be modified by any other command.
So far U-Boot does not program this field, and it does not prevent
SS device directly attached to root port, or HS device behind an HS
hub, from working, due to the fact that 'route string' is used by
the xHC to target SS packets. But in order to enumerate devices
behind an SS hub, this field must be programmed.
With this commit and along with previous commits, now SS & HS devices
attached to a USB 3.0 hub can be enumerated by U-Boot.
As usual, this new feature is only available when DM is on.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
For future extension, change xhci_setup_addressable_virt_dev()
signature to accept a pointer to 'struct usb_device', instead
of its members slot_id & speed, as the struct already contains
these two plus some other useful information of the device.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
USB 3.0 hub uses a hub depth value multiplied by four as an offset
into the 'route string' to locate the bits it uses to determine the
downstream port number. We shall set the hub depth value of a USB
3.0 hub after it is configured.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
USB 3.0 hub port status field has different bit positions from 2.0
hubs. Since U-Boot only understands the old version, translate the
new one into the old one.
Since we are going to add USB 3.0 hub support, this feature is only
available with driver model USB.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Sometimes we need know if a given hub device is root hub or not.
Add a new API to test this. This removes the xHCI driver's own
version is_root_hub() and change to use the new API.
While we are here, remove the unused/commented out get_usb_device()
in the xHCI driver too.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
|
|
At present hub_port_reset() is defined in DM USB, but it is never
called hence remove it (removing another ifdefs).
While we are here, change legacy_hub_port_reset() name to
usb_hub_port_reset() to better match other function names in the
same hub module.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Use USB hub device's dev->uclass_priv to point to 'usb_hub_device'
so that with driver model usb_hub_reset() and usb_hub_allocate()
are no longer needed.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
This cleans up the driver a little bit.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
As there is no board that currently uses xhci-pci driver without DM
USB, drop its support and leave only DM support.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Add CONFIG_USB_XHCI_PCI as a Kconfig option.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
|
|
USB 3.0 defines bMaxPacketSize0 field in the device descriptor as
the exponent of 2, so let's print the calculated actual size.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
|
|
Now that EHCD does not use CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS,
remove it in all boards' config files.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
|
|
EHC reports supported maximum number of ports in the HCSPARAMS
register, so it's unnecessary to use a hardcoded config option
CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
|
|
Now that xHCD does not use CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS,
remove it in all boards' config files.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
|
|
xHC reports supported maximum number of ports in the HCSPARAMS1
register, so it's unnecessary to use a hardcoded config option
CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
|
|
HCSPARAMS1:MaxPorts field specifies the maximum port number value,
and its valid values are in the range of 1 to 255.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
|
|
USB 3.0 hub port status has different bit position regarding to
port power, port speed, etc. But others are the same as 2.0 hubs.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
|
|
USB 3.0 hubs have a slightly different hub descriptor than USB 2.0
hubs, with a fixed (rather than variable length) size. Change the
host controller drivers that access those last two fields
(DeviceRemovable and PortPowerCtrlMask) to use the union.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
|
|
For accuracy, we should use 'sizeof(struct usb_port_status)' as the
wLength for 'get port status' request, although it happens to be
equal to 'sizeof(struct usb_hub_status)'.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
|
|
Testing a USB 3.0 hub by connecting it to the xHCI port on Intel
MinnowMax, when issuing 'get hub descriptor' to the hub, xHCI
reports a transfer event TRB with a completion code 6 which means
'Stall Error'.
In fact super speed USB hub descriptor type is 0x2a, not 0x29.
Sending correct SETUP packet to the hub makes it not stall anymore.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
|
|
It was observed that on Intel MinnowMax board, when xHCI is enabled
in the BayTrail SoC, with a USB 3.0 device connected to the bottom
USB 3.0 port (mapped to xHCI root port #7), its PORTSC register is
always 0x201203 (CCS = 1, CSC = 0). The root cause of such behavior
is unknown yet. Connect status change bit is set on the same port
with a USB 2.0 device (mapped to xHCI port #1, which is a different
port on the root hub).
With current logic in usb_scan_port(), the enumeration process will
abort if it does not detect a connect status change on a hub port.
However since a device connection status is correctly reported, the
enumeration process can still continue.
With this change, USB device connected to the bottom blue port on
MinnowMax board can be enumerated under either SS or HS mode.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Dinh Nguyen <dinguyen@kernel.org>
|
|
A valid input slot context for a 'configure endpoint' command requires
the 'Context Entries' field to be initialized to the index of the last
valid endpoint context that is defined by the target configuration. We
set up the 'Context Entries' field, but we forget to include the input
slot context in the input control context 'Add Context flags' bitmap.
So xHC will simply ignore input slot context and continue using its own
which contains old information of the device.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
|
|
The scratchpad buffer array is used to define the locations of
statically allocated memory pages that are available for the
private use of the xHC. The xHCI spec explicitly mentions that
system software shall allocate the scratchpad buffers before
placing the xHC in to Run mode (Run/Stop (R/S) = ‘1’), however
U-Boot is missing this part.
This causes xHC on Intel platform does not respond the very first
'enable slot' command that is given to xHC and the 'enable slot'
command completion event TRB is never generated and xHC seems to
hang forever.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
|
|
In xhci_queue_command(), when the command is not 'reset endpoint',
'stop endpoint' or 'set TR dequeue pointer', endpoint ID should not
be encoded in the TRB.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
|
|
There is no member called 'dma' in struct xhci_container_ctx. Remove
the comments that mentions it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
|
|
Build of ls1043ardb_sdcard & ls2088ardb_qspi secure targets showing
compilation error so removing them for the time being till propper
support has been applied.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
|
|
Update MC address caluclation as per MC design requirement
of address as least significant 512MB address
of MC private allocated memory.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Ashish Kumar <ashish.kumar@nxp.com>
|
|
config_board_mux() is dependent on 'hwconfig' env read value.
For some bootloaders like QSPI, env is ready only after
relocation. So delay execution of config_board_mux()
to misc_init_r().
Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
|
|
Update the default core frequency to 1800MHZ for best performance under
SD boot and eMMC boot.
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
|
|
Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
|
|
LS2080ARDB/LS2088ARDB updated RevF boards do not have
smart voltage translator, so no need to program GPIO
for LS2088ARDB boards
The GPIO programming is required only for LS2081ARDB.
Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
Enable validation of boot.scr script prior to its execution dependent
on "secureboot" flag in environment. Disable fall back option to
qspi boot in case of secure boot. Also enable "secureboot=y" flag
in environment for ARM based platforms instead of bootcmd.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Tested-by: Vinitha Pillai <vinitha.pillai@nxp.com>
|
|
Tested on ls1046ardb with automatically boot Ubuntu from SD card or
USB disk, if it fails to detect external storage disk, fall back to
qspi boot.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
|
|
Include common config_distro_defaults.h and config_distro_bootcmd.h
for u-boot enviroments to support distro boot which automatically
scan boot.scr from storage devices(e.g. SD/USB/SATA/SCSI disk) and
execute autoboot script.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Signed-off-by: Alison Wang <alison.wang@nxp.com>
|
|
Move the macro to defconfig to take effect globally.
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
|
|
Adds a new field in fsg_common namely controller_index to support
multiple controllers usb gadget support.
Signed-off-by: Rajat Srivastava <rajat.srivastava@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
|
|
Adds helper functions to enable snooping and outstanding burst beat
settings.
Signed-off-by: Rajat Srivastava <rajat.srivastava@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
|
|
USB3PHY Observing Intermittent Failure in Rx
This patch is adding the erratum for LS1021.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: yinbo.zhu <yinbo.zhu@nxp.com>
|
|
USB3 LFPS Peak-Peak Differential Output Voltage Adjustment
This patch is adding the erratum for LS1021.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: yinbo.zhu <yinbo.zhu@nxp.com>
|
|
USB High Speed Squelch Threshold Adjustment
This patch is adding the erratum for LS1021.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: yinbo.zhu <yinbo.zhu@nxp.com>
|
|
USB High Speed (HS) EYE Height Adjustment
This patch is adding the erratum for LS1021.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: yinbo.zhu <yinbo.zhu@nxp.com>
|
|
Add the secure boot defconfig for QSPI boot on LS2088ARDB
platform.
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
|
|
The QSPI support the direct 4bytes address command for flash
read/write/erase.
And the address can cover the whole QSPI memory space.
signed-off-by: Yuan Yao <yao.yuan@nxp.com>
|
|
Some new flash don't support bar register but use 4bytes address to
support exceed 16MB flash size.
So add flash flag: ADDR_4B
for some flash which support 4bytes address.
Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
|
|
As per data sheet, S25FS512S support Uniform sector option
or erase size of 256 kbytes and Page Programming buffer of
256 or 512 Bytes. So, flag SECT_4K have no significance
for this flash.
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
|
|
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Cc: Wolfgang Denk <wd@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
|
|
If the value of either "nand options" or "bbt options" has a zero in
the most significant nibble, the '0x' prefix will be isolated from the
value like shown below:
|Device 0: nand0, sector size 128 KiB
| Page size 2048 b
| OOB size 64 b
| Erase size 131072 b
| subpagesize 2048 b
| options 0x40000200
| bbt options 0x 60000
Change the format string to produce leading zeroes filling the gap.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
|
|
This error code has not been upstreamed and is not really needed since it
is unlikely to be triggered. Drop it to maintain compatability with
upstream.
Reported-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
|
|
Signed-off-by: Tom Rini <trini@konsulko.com>
|
