| Age | Commit message (Collapse) | Author |
|---|
|
Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
|
|
Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
|
|
Declared all functions that were not called outside the file as static
Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
|
|
|
|
|
|
Update CHANGELOG
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
The ml300 board has a number of issues, but nobody cares about this
long-orphaned board any more. Remove it.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Michal Simek <monstr@monstr.eu>
|
|
|
|
The restructuring of the mkimage command in commit 89a4d6b1 ("tools:
mkimage: split code into core, default and FIT image specific")
introduced a bug that caused mkimage to segfault when run without
"-n name" option. Initialize the imagename entry to prevent that.
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
|
|
|
|
This patch adds status polling method to offer an alternative to
data toggle method for amd flash chips.
This patch is needed for nios2 cfi flash interface, where the bus
controller performs 4 bytes read cycles for a single byte read
instruction. The data toggle method can not detect chip busy
status correctly. So we have to poll DQ7, which will be inverted
when the chip is busy.
This feature is enabled with the config def,
CONFIG_SYS_CFI_FLASH_STATUS_POLL
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
With old configuration it could happen tout=0 if CONFIG_SYS_HZ<1000.
Signed-off-by: Renato Andreola <renato.andreola@imagos.it>
Signed-off-by: Alessandro Rubini <rubini@gnudd.com>
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
The ATMEL flash does not have buffer write feature. Assgined
buffer_size = 1, so that when there is a write to the flash
will not use buffer write function.
Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
|
|
The flash location is at 0xff800000, not 0
Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
|
|
The CF will call cache functions in lib_m68/cache.c and the
cache settings are defined in platform configuration file.
Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
|
|
The proper SDRAM size is 32MB not 64MB
Signed-off-by: Jingchang Lu <b22599@freescale.com>
|
|
Reside Ethernet buffer descriptors in SRAM instead of DRAM. Add
CONFIG_SYS_TX_ETH_BUFFER in platform configuration file. Update
DRAM control and SRAM control register setting. Update cache
setting where size does not write to proper region.
Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
|
|
Add CPU compile flag -mcpu=53015 in cpu/config.mk
Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
|
|
Provide extra environment Data. Remove default network
address and MAC address.
Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
|
|
Fix proper portsize: The register for portsize is either 00b, 01b,
or 1xb. The value that previous assigned is 32d.
Fix DRAM bring up: insert asm("nop") for every DRAM register setup
Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
|
|
Fix incorrect default environment for flash erase or protect
range. Change offset from 0 to 0xff80nnnn. Remove default
ethernet setup and MAC address.
Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
|
|
Newer ColdFire processors family boot from address 0 instead of
0xFFnn_nnnn. When the boot flash base chip select is set at new
location instead of 0, an un-predictable error will occur if
there is an vector being trigger and refer it to an invalid
address or the vector table handler is not existed at address
0.
Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
|
|
Provide proper port passing from serial_init to uart_part_conf.
Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
|
|
Provide parameter passing to uart_port_config(). Update port
configuration - un-mask it before enable the bits.
Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
|
|
Use correct definition for _MASK and _UNMASK. It was combined in
the previous used and causes confusion.
Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
|
|
This fixes the following warnings when running MAKEALL for coldfire :
cmd_bdinfo.c:354: warning: 'print_eth' defined but not used
Signed-off-by: Philippe De Muyter <phdm at macqel.be>
|
|
Mercury-EP2500.patch
- added Mercury's EP2500 board uses the mcf5282 processor
CREDITS.patch
Signed-off-by: David Wu <davidwu@arcturusnetworks.com>
Signed-off-by: Michael Durrant <mdurrant@arcturusnetworks.com>
|
|
Using seperate function calls for each bit-bang of slave serial
load can be painfully slow. This patch adds the possibility to
supply a block write function that loads the complete block of
data in one call (like it can already be done with Altera FPGAs).
On an MCF5373L (240 MHz) loading an XC3S4000 this reduces the load
time from around 15 seconds to around 3 seconds
Signed-off-by: Wolfgang Wegner <w.wegner at astro-kom.de>
|
|
This patch adds support for ASTRO board(s) based on MCF5373L.
Signed-off-by: Wolfgang Wegner <w.wegner@astro-kom.de>
|
|
440EPx fixed bootstrap options A, B, D, and E sets PLL FWDVA to a value = 1.
This results in the PLLOUTB being greater than the CPU clock frequency
resulting unstable 440EPx operation resulting in various software hang
conditions.
This patch reprograms the FWDVA satisfying the requirement of setting FWDVB
to a value greater than 1 while using one of the four deafult bootstrap options.
Signed-off-by: Rupjyoti Sarmah <rsarmah@amcc.com>
Acked-by : Victor Gallardo <vgallardo@appliedmicro.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
|
|
The soft-i2c code for AT91 defines I2C_SOFT_DECLARATIONS
for direct access by dereferencing a pio pointer.
The OTC570 platform uses the AT91 gpio API so it does not
need the pio variable.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
|
|
Support for 16bpp was supposed to be in the code but was not working.
This makes it work and has been tested in the nhk8815 board.
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
|
|
When issuing a nand scrub command, the entered character is not displayed
this may be confusing. This patch makes the input character being
displayed if it is a 'y' so that an user knows he is about to scrub his
nand.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
This is a patch to use the hardware ECC controller of
the AT91SAM9260 for the AT91 nand. Taken from the kernel 2.6.33.
Signed-off-by: Nikolay Petukhov <Nikolay.Petukhov@gmail.com>
|
|
Modified to use IO accessor routines consistently. Eliminated volatile usage
to keep checkpatch.pl happy.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
|
|
|
|
Update CHANGELOG
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
ep93xx timer: Make get_ticks() return a value in CONFIG_SYS_HZ resolution,
as announced by get_tbclk()
Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
|
|
ep93xx timer: Use 64-bit values in usecs_to_ticks() in order to avoid
overflows in intermediate values
Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
|
|
|
|
Allow overwriting defined partitions in the device tree blob
using partition info defined in the 'mtdparts' environment
variable.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Gerald Van Baren <vanbaren@cideas.com>
|
|
Match history buffer size to console buffer size. History buffer size
was hard coded to 256, artificially limiting the command buffer size.
The history buffer now tracks CONFIG_SYS_CBSIZE.
Signed-off-by: John Schmoller <jschmoller@xes-inc.com>
|
|
When CONFIG_SYS_CBSIZE equals MAX_CMDBUF_SIZE, a command string of
maximum length will overwrite part of the history buffer, causing the
board to die. Expand the console_buffer and hist_lines buffer by one
character each to hold the missing NULL char.
Signed-off-by: John Schmoller <jschmoller@xes-inc.com>
|
|
Add POST progress API implemented as weak calls before and after
each call to the POST test callback in the post_run_single routine
of the post.c file.
Signed-off-by: Michael Zaidman <michael.zaidman@gmail.com>
Acked-by: Detlev Zundel <dzu@denx.de>
|
|
This patch add functionality to use memory addresses in expressions.
This increases the power of expressions substantially
It adheres to the standard convemtions: memory addresses can be given
in the format *address (e.g. *1000)
Rationale for this change is that it allows masking off bits from a
byte that is obtained by reading data from e.g. i2c.
Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
Fix warning: control reaches end of non-void function
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
|
|
Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
|
