| Age | Commit message (Collapse) | Author |
|---|
|
This option should not really be user selectable. Note that on PowerPC
we currently only need BOARD_LATE_INIT when CHAIN_OF_TRUST is enabled so be
conditional on that.
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com> (for UniPhier)
|
|
Introduce board/freescale/common/Kconfig so that we have a single place
for CONFIG options that are shared between ARM and PowerPC NXP platforms.
Cc: York Sun <york.sun@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
Rename CONFIG_IMX31_PHYCORE_EET to CONFIG_TARGET_IMX31_PHYCORE_EET and
make this a distinct config target.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
The directory structure of device tree files produced by the kernel's
'make dtbs_install' is different on ARM64, the RPi3 device tree file is
in a 'broadcom' subdirectory there.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
|
|
Print the error code for non-zero (failure case) instead
of making debug statement without any condition, this
usually gives proper clue in failure condition.
Log:
|
|
The sdhci controller assumes that the base clock frequency is fully supported by
the peripheral and doesn't support hardware limitations. The Linux kernel
distinguishes between base clock (max_clk) of the host controller and maximum
frequency (f_max) of the card interface. Use the same differentiation and allow
the platform to constrain the peripheral interface.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
|
|
- Allow to disable SPL (mainly for ATF)
- Refactor SoC init code
- Update DRAM settings
- Add PXs3 SoC support (DT, pinctrl driver, SoC code)
|
|
Initial support for PXs3 SoC.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Initial commit for the PXs3 SoC DT.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Add pin configuration and pinmux support for UniPhier PXs3 SoC.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
All the UniPhier DT files are compiled if CONFIG_ARCH_UNIPHIER
is enabled, but not all of them actually work. For example, when
U-Boot is compiled for ARM 32 bit, 64 bit DT files are also built,
and vice versa. Compile only the combination that makes sense.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
There are similar functions that look up SoC data by the SoC ID.
The new macro UNIPHIER_DEFINE_SOCDATA_FUNC will be helpful to
avoid the code duplication.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Currently, uniphier_get_soc_type() converts the SoC ID (this is
read from the revision register) to an enum symbol to use it for SoC
identification. Come to think of it, there is no need for the
conversion in the first place. Using the SoC ID from the register
as-is a straightforward way.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
The <common.h> includes too many headers. Actually, these files
needed to include it for udelay() declaration. Now we can replace
it with <linux/delay.h> thanks to commit 5bc516ed661a ("delay:
collect {m, n, u}delay declarations to include/linux/delay.h").
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
These files only need error number macros. Actually, IS_ERR(),
PTR_ERR(), ERR_PTR(), etc. are not useful for U-Boot. Avoid
unnecessary header includes.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
This defconfig does not support SPL. If you use this, the basic
SoC initialization must be done in firmware that runs before U-Boot.
(Generally, ARM Trusted Firmware is expected to do this job).
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
We may want to run different firmware before running U-Boot. For
example, ARM Trusted Firmware runs before U-Boot, making U-Boot
a non-secure world boot loader. In this case, the SoC might be
initialized there, which enables us to skip SPL entirely.
This commit removes "select SPL" to make it configurable. This
also enables the Multi SoC support for the UniPhier ARMv8 SoCs.
(CONFIG_ARCH_UNIPHIER_V8_MULTI) Thanks to the driver model and
Device Tree, the U-Boot proper part is now written in a generic way.
The board/SoC parameters reside in DT. The Multi SoC support
increases the memory footprint a bit, but the U-Boot proper does
not have strict memory constraint. This will mitigate the per-SoC
(sometimes per-board) defconfig burden.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
These are file-internal and constant.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
The ddrphy_shift_rof_hws() never writes back the shifted delay value
to the register, which makes this function non-effective.
Signed-off-by: Kotaro Hayashi <hayashi.kotaro@socionext.com>
[masahiro: add git log]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Change bnk_typ's value from 8 to 0 (for G1's performance).
Signed-off-by: Wataru Okoshi <okoshi.wataru@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
On occasion the job that does these two build types will hit the time
limit so split this in two.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Move all of the status LED feature to drivers/led/Kconfig.
The LED status definitions were moved from the board configuration
files to the defconfig files.
TBD: Move all of the definitions in the include/status_led.h to the
relevant board's defconfig files.
Tested boards: CL-SOM-AM57x, CM-T335
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
|
|
Move all of the status LED feature to drivers/led/Kconfig.
doc/README.LED updated to reflect the Kconfig implementation.
Tested boards: CL-SOM-AM57x, CM-T335
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
|
|
Cc: Tom Rini <trini@konsulko.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
|
|
This patch add Kconfig entry for CONFIG_BOARD_LATE_INIT
Cc: Tom Rini <trini@konsulko.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
|
|
When falcon mode support was added, it was right around when SPL_OS_BOOT
was migrated to Kconfig. So first we must move the enablement to the
defconfig file. Next, it turned off EXT support rather than add the
information to allow for falcon mode from EXT. Add this information so
that the board compiles after 5d28b930f237.
Fixes: d96796ca23b2 ("mx6sabresd: Add Falcon mode support")
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Instead of disabling the data cache in the bootelf command, disabling
it in the do_bootm_qnxelf function.
Some ELF binary might want the cache enabled.
Signed-off-by: Emmanuel Vadot <manu@bidouilliste.com>
|
|
Reported-by: Coverity (CID: 155214)
Signed-off-by: Sven Ebenfeld <sven.ebenfeld@gmail.com>
|
|
Latest gcc compile strted complaining about defined structure definition
that are not used. Remove the unused sturctures.
Reported-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
Latest gcc 6.2 compiler is throwing the below warning for omap4_panda_defconfig
arch/arm/mach-omap2/omap4/hw_data.c:136:3: warning: 'abe_dpll_params_sysclk_196608khz' defined but not used [-Wunused-const-variable=]
abe_dpll_params_sysclk_196608khz[NUM_SYS_CLKS] = {
Fix this by guarding it with CONFIG_SYS_OMAP_ABE_SYSCK
Reported-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
The built _libfdt.so is placed in the /tools dir and need to say here
as it contains relative paths.
Add the directory to the python path so binman can use this module.
Signed-off-by: Emmanuel Vadot <manu@bidouilliste.com>
|
|
Do not rely on CONFIG_SPL_OF_PLATDATA to build the libfdt python module.
If swig is present, this will be build
Signed-off-by: Emmanuel Vadot <manu@bidouilliste.com>
|
|
Signed-off-by: Lukasz Majewski <lukma@denx.de>
|
|
Use the generic "distro" boot framework to enable automatic DHCP boot.
MMC and USB are not yet implemented, so this is the only boot option.
The fdt and kernel addresses are adopted from downstream; ramdisk and
scriptaddr addresses were chosen arbitrarily.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Alexander Graf <agraf@suse.de>
|
|
Move it from meson-gxbb-common.h to odroid-c2.h to allow new boards not
to implement it.
Signed-off-by: Andreas Färber <afaerber@suse.de>
|
|
We can make the code read more easily here by simply using memset()
always as when we don't have an optimized version of the function we
will still have a version of this function around anyhow.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
We have long had available optimized versions of the memset and memcpy
functions that are borrowed from the Linux kernel. We should use these
in normal conditions as the speed wins in many workflows outweigh the
relatively minor size increase. However, we have a number of places
where we're simply too close to size limits in SPL and must be able to
make the size vs performance trade-off in those cases.
Cc: Philippe Reynes <tremyfr@yahoo.fr>
Cc: Eric Jarrige <eric.jarrige@armadeus.org>
Cc: Heiko Schocher <hs@denx.de>
Cc: Magnus Lilja <lilja.magnus@gmail.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Chander Kashyap <k.chander@samsung.com>
Cc: Akshay Saraswat <akshay.s@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
While moving OMAP related files to mach-omap2 the functionality
relating to generating secure boot files was modified. This change
prevents secure platforms other than AM33xx and OMAP54XX from
correctly building files for all needed media types.
Fixes: 983e37007da5 ("arm: Introduce arch/arm/mach-omap2 for OMAP2 derivative platforms")
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
|
|
These files are only included for build by the make system
when CONFIG_SPL_{EXT,FAT}_SUPPORT is enabled, remove the unneed
checks for these in the source files.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
IEC 80000-13:2008 Quantities and units
Part 13: Information science and technology
defines the prefixes to use for binary multiples.
So instead of writing
Data Size: 6726132 Bytes = 6568.49 kB = 6.41 MB
in dumpimage we should write
Data Size: 6726132 Bytes = 6568.49 KiB = 6.41 MiB.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
|
|
In a config with one MMC at device id '1' and no MMC at device id '0'
(a BeagleBone Black with no sd inserted for example), the current code
will first test to access the MMC 0 (sd port), seeing that no device is
present it will simply return that no more device are present for this
class.
This patch fixes this by testing all devices for each class.
Signed-off-by: Emmanuel Vadot <manu@bidouilliste.com>
|
|
The current code can loop undefinitly as it doesn't parse
correctly the env data.
Since the env is an hashtable, use the hashtable function for
the API_ENV_ENUM api call.
Signed-off-by: Emmanuel Vadot <manu@bidouilliste.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
|
|
Some scripts are calling the same functions, so these changes consolidate
common scripts together to reduce redundancy and shrink size a bit. This
also keeps the 'bootargs' variable from growing if manually called more
than one time. This also adds NAND booting scripts based on newly consolidated
scripts.
Signed-off-by: Adam Ford <aford173@gmail.com>
|
|
In 35fc84f, bootm was refactored so plain 'bootm' and
'bootm <subcommand>' shared a common implementation.
The 'bootm ramdisk' command implementation is now part of the common
implementation but not invoke by plain 'bootm' since the original
implementation never did ramdisk relocation. Instead, ramdisk
relocation happened in image_setup_linux() which is typically called
during the OS portion of 'bootm'.
On ARM, parameters to the Linux kernel can either be passed by FDT or
ATAGS. When using FDT, image_setup_linux() is called which also triggers
ramdisk relocation. When using ATAGS, image_setup_linux() is _not_
called because it mostly does FDT setup.
Instead of calling image_setup_linux() in both FDT and ATAGS cases,
include BOOTM_STATE_RAMDISK in the requested states during a plain
'bootm' if CONFIG_SYS_BOOT_RAMDISK_HIGH is set and remove the ramdisk
relocation from image_setup_linux(). This causes ramdisk relocation to
happen on any system where CONFIG_SYS_BOOT_RAMDISK_HIGH regardless of
the OS being booted. Also remove IMAGE_ENABLE_RAMDISK_HIGH as it was
only used by the now-removed code from image_setup_linux().
Signed-off-by: Rick Altherr <raltherr@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
|
|
commit: 65f83802b7a5b "serial: 16550: Add getfcr accessor"
breaks u-boot commandline working with long commands
sending to the board.
Since the above patch, you have to setup the fcr register.
For board/archs which enable OF_PLATDATA, the new field
fcr in struct ns16550_platdata is not filled with a
default value ...
This leads in not setting up the uarts fifo, which ends
in problems, when you send long commands to u-boots
commandline.
Detected this issue with automated tbot tests on am335x
based shc board.
The error does not popup, if you type commands. You need
to copy&paste a long command to u-boots commandshell
(or send a long command with tbot)
Possible boards/plattforms with problems:
./arch/arm/cpu/arm926ejs/lpc32xx/devices.c
./arch/arm/mach-tegra/board.c
./board/overo/overo.c
./board/quipos/cairo/cairo.c
./board/logicpd/omap3som/omap3logic.c
./board/logicpd/zoom1/zoom1.c
./board/timll/devkit8000/devkit8000.c
./board/lg/sniper/sniper.c
./board/ti/beagle/beagle.c
./drivers/serial/serial_rockchip.c
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Tested-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
|
|
On LS1012ARDB board, three dual 1:4 mux/demux devices drive the SDHC2
signals to eMMC, SDIO wifi, SPI and Ardiuno shield. Only when we select
eMMC and SDIO wifi, the SDHC2 could be used. Otherwise, the command
inhibit bits of eSDHC2_PRSSTAT register will never release. This would
cause below continious error messages in linux since it uses polling
mode to detect card.
"mmc1: Controller never released inhibit bit(s)."
"mmc1: Controller never released inhibit bit(s)."
"mmc1: Controller never released inhibit bit(s)."
This patch is to define esdhc_status_fixup function for RDB to disable
SDHC2 status if no SDIO wifi or eMMC is selected.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
The LS1012AQDS board has a hardware issue. When there is no eMMC
adapter card inserted in SDHC2 adapter slot, the command inhibit
bits of eSDHC2_PRSSTAT register will never release. This would cause
below continious error messages in linux since it uses polling mode
to detect card.
"mmc1: Controller never released inhibit bit(s)."
"mmc1: Controller never released inhibit bit(s)."
"mmc1: Controller never released inhibit bit(s)."
This patch is to define esdhc_status_fixup function for QDS to
disable SDHC2 status if no eMMC adapter card is detected.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
