summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2010-09-03ppc4xx: Invalidate d-cache when used as init-ramStefan Roese
We need to invalidate the data cache after it has been used as init-ram. This problem was detected on the lwmon5 update. Signed-off-by: Stefan Roese <sr@denx.de>
2010-09-03ppc4xx: Fix 440EPx bug in reconfigure_pll()Stefan Roese
This patch fixes a bug in reconfigure_pll(), where the detection of the current bootstrap option is wrong. The ICS bits where incorrectly shifted. This bug was found on the lwmon5 board, which uses bootstrap option H (I2C bootstrap EEPROM). Additionally a bit of code was moved into the if statement, since its only used after later on. No need to run this code all the time. Also, a few empty lines are added to make the code better readable. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Rupjyoti Sarmah <rsarmah@amcc.com> Cc: Victor Gallardo <vgallardo@appliedmicro.com>
2010-09-03ppc4xx: Fix APC405 board supportMatthias Fuchs
Opps, after a long time I tested recent u-boot on our APC405 board. This simple fix makes networking work again. Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu> Signed-off-by: Stefan Roese <sr@denx.de>
2010-08-18Merge branch 'master' of ssh://gemini/home/wd/git/u-boot/masterWolfgang Denk
2010-08-18ARM: Update ARM mach-typesSandeep Paulraj
This patch updates the mach-types.h based on the latest linux kernel Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-08-18Work around bug in Numonyx P33/P30 256-Mbit 65nm flash chips.Philippe De Muyter
I have "ported" U-boot to a in house made board with Numonyx Axcell P33/P30 256-Mbit 65nm flash chips. After some time :( searching for bugs in our board or soft, we have discovered that those chips have a small but annoying bug, documented in "Numonyx Axcell P33/P30 256-Mbit Specification Update" It states : When customer uses [...] block unlock, the block lock status might be altered inadvertently. Lock status might be set to either 01h or 03h unexpectedly (00h as expected data), which leads to program/erase failure on certain blocks. A working workaround is given, which I have applied and tested with success : Workaround: If the interval between 60h and its subsequent command can be guaranteed within 20us, Option I is recommended, otherwise Option II (involves hardware) should be selected. Option I: The table below lists the detail command sequences: Command Data bus Address bus Remarks Sequence 1 90h Block Address Read Lock Status 2 Read Block Address + 02h (2)(3) (1) 3 60h Block Address (2)(3) (1) Lock/Unlock/RCR Configuration 4 D0h/01h/03h Block Address Notes: (1) Block Address refers to RCR configuration data only when the 60h command sequence is used to set RCR register combined with 03h subsequent command. (2) For the third and fourth command sequences, the Block Address must be the same. (3) The interval between 60h command and its subsequent D0h/01h/2Fh/03h commands should be less than 20us. And here is a log comparison of a simple (destructive) flash test without and with the workaround. diff without-numonyx-workaround.log with-numonyx-workaround.log -U-Boot 2010.06-00696-g22b002c-dirty (Aug 16 2010 - 15:07:47) +U-Boot 2010.06-00696-g22b002c-dirty (Aug 16 2010 - 15:25:19) CPU: Freescale MCF5484 CPU CLK 200 MHz BUS CLK 100 MHz Board: Macq Electronique ME2060 I2C: ready DRAM: 64 MiB FLASH: 32 MiB In: serial Out: serial Err: serial Net: FEC0, FEC1 -> flinfo Bank # 1: CFI conformant FLASH (16 x 16) Size: 32 MB in 259 Sectors Intel Extended command set, Manufacturer ID: 0x89, Device ID: 0x8922 Erase timeout: 4096 ms, write timeout: 1 ms Buffer write timeout: 5 ms, buffer size: 1024 bytes Sector Start Addresses: FE000000 RO FE008000 RO FE010000 RO FE018000 RO FE020000 RO FE040000 RO FE060000 RO FE080000 RO FE0A0000 RO FE0C0000 RO ... FFF80000 RO FFFA0000 RO FFFC0000 RO FFFE0000 RO -> protect off all Un-Protect Flash Bank # 1 ................... done -> erase all Erase Flash Bank # 1 ................... done -> cp.b 1000000 fe000000 2000000 -Copy to Flash... Flash not Erased +Copy to Flash... done -> Signed-off-by: Philippe De Muyter <phdm@macqel.be> Signed-off-by: Stefan Roese <sr@denx.de>
2010-08-18cfi_flash: Cleanup flash_print_info()Stefan Roese
This patch does the following: - Extract code to detect if sector is erased into function sector_erased(). - Because of this, we don't have variable declarations inside the sector loop in flash_print_info() - Change "return" to "break" in the "if (ctrlc()) statement: This fixes a problem with the resulting output. Before this patch the output was: Sector Start Addresses: FC000000 FC020000 FC040000 => With this patch it is now: Sector Start Addresses: FC000000 FC020000 FC040000 => Signed-off-by: Stefan Roese <sr@denx.de> Cc: Kim Phillips <kim.phillips@freescale.com> Cc: Wolfgang Denk <wd@denx.de>
2010-08-18Fix printing & reading of 16-bit CFI device identifiersPhilippe De Muyter
Fix reading and printing of CFI flashes 16-bit devices identifiers Nowadays CFI flashes have a 16-bit device identifier. U-boot still print them and read them as if they were only 8-bit wide. Fix that. Before: Intel Extended command set, Manufacturer ID: 0x89, Device ID: 0x1B After: Intel Extended command set, Manufacturer ID: 0x89, Device ID: 0x881B Signed-off-by: Philippe De Muyter <phdm@macqel.be> Signed-off-by: Stefan Roese <sr@denx.de>
2010-08-18cfi_flash: flinfo: allow user interrupt in flash print info fnKim Phillips
flashes getting larger, users more impatient. Signed-off-by: Kim Phillips <kim.phillips@freescale.com> Signed-off-by: Stefan Roese <sr@denx.de>
2010-08-13env_nand: return error when no device is foundMike Frysinger
Currently, if there is an error probing the NAND chip and the env is based in NAND, the readenv() function will use a NULL function pointer and thus jump to address 0. Here I just check for a non-zero value of blocksize as that shouldn't be zero when a valid device is found, but perhaps there is a better way for someone familiar with the NAND internals to suggest. Signed-off-by: Mike Frysinger <vapier@gentoo.org> Tested-by: Ben Gardiner <bengardiner@nanometrics.ca>
2010-08-12Merge branch 'master' of git://git.denx.de/u-boot-usbWolfgang Denk
2010-08-12Fixed clobbered output of the "help usb" commandSergei Poselenov
The "usb help" doesn't format the output correctly: => help usb usb - USB sub-system Usage: usb reset - reset (rescan) USB controller usb stop [f] - stop USB [f]=force stop usb tree - show USB device tree usb info [dev] - show available USB devices usb storage - show details of USB storage devices usb dev [dev] - show or set current USB storage device usb part [dev] - print partition table of one or all USB storage devices usb read addr blk# cnt - read `cnt' blocks starting at block `blk#' to memory address `addr'usb write addr blk# cnt - write `cnt' blocks starting at block `blk#' from memory address `addr' => With fix below applied, the output is correct: => help usb usb - USB sub-system Usage: usb reset - reset (rescan) USB controller usb stop [f] - stop USB [f]=force stop usb tree - show USB device tree usb info [dev] - show available USB devices usb storage - show details of USB storage devices usb dev [dev] - show or set current USB storage device usb part [dev] - print partition table of one or all USB storage devices usb read addr blk# cnt - read `cnt' blocks starting at block `blk#' to memory address `addr' usb write addr blk# cnt - write `cnt' blocks starting at block `blk#' from memory address `addr' => Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com>
2010-08-12AM3517EVM: musb: add usb configAjay Kumar Gupta
Enabling USB HOST in defconfig. Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
2010-08-12musb: am35x: Workaround for fifo read issueAjay Kumar Gupta
AM35x supports only 32bit read operations so we need to have workaround for 8bit and 16bit read operations. Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
2010-08-12musb: MSC host support for AM35xAjay Kumar Gupta
Tested MSC Host on AM3517EVM. Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
2010-08-12AM35x: Adding SCM general register definitionsAjay Kumar Gupta
Adding general register structure of system control module (SCM) of AM35x. This would be required to access devconf2 and ip_sw_reset register in musb module. Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
2010-08-11Blackfin: re-use board data in cpu bannerMike Frysinger
The bi_cpu field of the board data is already set to the relevant cpu string, so there is no need for us to use the define directly. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-08-11Blackfin: cm-bf548: increase monitor lenMike Frysinger
Recent features enabled by default require a larger monitor size for the cm-bf548 port, so bump it up a bit. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-08-11Blackfin: shutdown video DMA when booting LinuxMichael Hennerich
In case there is no frame buffer driver present in Linux to hand over the PPI LCD DMA upon boot, the DMA initiated by u-boot to display the splash screen runs unattended. Therefore always stop the video driver in u-boot before starting Linux. If people don't want this behavior, then they can simply stub out the video_stop() function in their board video driver. Signed-off-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-08-10disk/part.c: 'usb storage' avoiding overflow when output capacitySergei Trofimovich
Before: Marvell>> usb storage Device 0: Vendor: StoreJet Rev: Prod: Transcend Type: Hard Disk Capacity: 28759.9 MB = 28.0 GB (488397168 x 512) After: Marvell>> usb storage Device 0: Vendor: StoreJet Rev: Prod: Transcend Type: Hard Disk Capacity: 238475.1 MB = 232.8 GB (488397168 x 512) Signed-off-by: Sergei Trofimovich <slyfox@gentoo.org>
2010-08-10Merge branch 'master' of git://git.denx.de/u-boot-armWolfgang Denk
2010-08-10Merge branch 'master' of git://git.denx.de/u-boot-netWolfgang Denk
2010-08-10Merge branch 'master' of git://git.denx.de/u-boot-imxWolfgang Denk
2010-08-10orion5x: allow overriding default mappings windowsAlbert Aribaud
Turn all ORION5X_DEF{ADR,SZ}_xxx macros into ORION5X_{ADR,SZ}_xxx and allow defining them from board code to override defaults. This is particularly useful for defining board-specific FLASH address and size in board header file rather than having to tweak orion5x code. Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
2010-08-10Merge branch 'master' of git://git.denx.de/u-boot-marvellWolfgang Denk
2010-08-10Merge branch 'master' of git://git.denx.de/u-boot-tiWolfgang Denk
2010-08-10Merge branch 'master' of ../masterWolfgang Denk
2010-08-10MX51EVK: fix return value of get_timer_maskedLi Haibo
get_timer_masked() should return current timestamp, not current ticks from hardware register. Tested on one custom board with NAND flash. Without this patch, NAND write always TIMEOUT because get_timer(0) return a big value. This patch applies for u-boot-2010.06 Signed-off-by: Li Haibo <hbli@sinocastel.com>
2010-08-10fix cmd_mmc.c, line 136 missing "Reinhard Meyer
Remove warning for missing " at the end of line 136 Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
2010-08-09Fix compile warnings for const correctnessBen Warren
Commit 6e37b1a3a25004d3df5867de49fff6b3fc9c4f04 modifies several net calls to take a (const char *) parameter instead of (char *), but in some cases the modified functions call other functions taking (char *). The end result is warnings about discarding the const qualifier. This patch fixes these other function signatures. Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-08-09miiphy: leverage current_mii cache moreMike Frysinger
For code that uses miiphy_{read,write}, every call invokes a full look up of the mii list. There is already a "current_mii" cache that is used by some code, but have the miiphy_{read,write} function use it as well. This does increase the code size slightly, but I think it's worth it. Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-08-09miiphy: unify device list lookupMike Frysinger
Rather than have every func re-implement the list walking code, do it one local function. This shrinks the resulting object code a little while making the source much more manageable. Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-08-09miiphy: constify device nameMike Frysinger
The driver name does not need to be writable, so constify it. Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-08-09net: rename "FSL UECx" net interfaces "UECx"Kim Phillips
continuation of commit 2ecc2262d66a286e3aac79005bcb5f461312dea8 "net ppc: fix ethernet device names with spaces" (currently in u-boot-net.git) for QE based parts. Signed-off-by: Kim Phillips <kim.phillips@freescale.com> Acked-by: Dave Liu <daveliu@freescale.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-08-09net ppc: fix ethernet device names with spacesHeiko Schocher
since commit 1384f3bb8a4f9066805b70c1418eda78ecb73fdd ethernet names with spaces drop a Warning: eth device name has a space! message. This patch fix it for: - "FEC ETHERNET" devices found on mpc512x, mpc5xxx, mpc8xx and mpc8220 boards. renamed to "FEC". - "SCC ETHERNET" devices found on mpc8xx, mpc82xx based boards. Renamed to "SCC". - "HDLC ETHERNET" devices found on mpc8xx boards Renamed to "HDLC" - "FCC ETHERNET" devices found on mpc8260 and mpc85xx based boards. Renamed to "FCC" Tested on the kup4k board. Signed-off-by: Heiko Schocher <hs@denx.de> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-08-09net,fec: Shorten device name as done for other driversStefano Babic
After discussion on the ML it is suggested to drop unrequired and not useful characters from the device name. This patch changes the name for the fec_mxc driver from "FEC_MXC" to "FEC". Signed-off-by: Stefano Babic <sbabic@denx.de> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-08-09ppc4xx: Fix/Update katmai board headerStefan Roese
This patch has the following fixes/changes: - Set 'kernel_addr' and 'ramdisk_addr' to correct values and add 'fdt_addr' environment variable - Remove 'kozio' environment variable - Remove environmant variables to boot ancient arch/ppc Linux kernels - Remove CONFIG_SYS_BOOTMAPSZ definition. It's already defined to the same value in amcc-common.h Signed-off-by: Stefan Roese <sr@denx.de>
2010-08-09ppc4xx: Fix building of sc3 boardHeiko Schocher
Update image size after addition of new environment handling. Signed-off-by: Heiko Schocher <hs@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
2010-08-09ppc4xx: Fix building of PMC440 boardMatthias Fuchs
Update image size and default environment after addition of new environment handling. Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu> Signed-off-by: Stefan Roese <sr@denx.de>
2010-08-09ppc4xx: Fix building of CANBT boardMatthias Fuchs
Update image size after addition of new environment handling. Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu> Signed-off-by: Stefan Roese <sr@denx.de>
2010-08-09ppc4xx: Fix building of AR405 boardMatthias Fuchs
Update image size after addition of new environment handling. Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu> Signed-off-by: Stefan Roese <sr@denx.de>
2010-08-09ppc4xx: cleanup default environment for AMCC boardsWolfgang Denk
None of the AMCC boards uses an embedded environment, so there is no need to run "saveenv" after updating U-Boot. Drop the redundant commands from the default environment. Signed-off-by: Wolfgang Denk <wd@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
2010-08-08PXA: Declare __io for vpac270 IDEMarek Vasut
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
2010-08-08PXA: Fix missing includesMarek Vasut
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
2010-08-08PXA: Fix off-the-tree build problemsMarek Vasut
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
2010-08-08config.mk: avoid -traditional-cpp on OS X 10.5Mike Frysinger
Simply trying to include a basic header file like stdlib.h on OS X 10.5 and then building with -traditional-cpp fails with lots of errors like: In file included from /usr/include/stdlib.h:63, from test.c:3: /usr/include/available.h:85: error: stray '#' in program /usr/include/available.h:85: error: syntax error before numeric constant /usr/include/available.h:86: error: stray '#' in program In the past, I hadn't noticed because the old logic for these flags were restricted to Darwin running on PowerPC systems while I'm running on an Intel system. But after some recent clean ups and changes, the flag was being applied to all Darwin systems and my host tools broke. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-08-08fdt: Fix bug in size calculation in fdt_resize() with initrd useFeng Wang
Original bug description from Feng (fdt_resize() bug caused "WARNING: could not set linux, initrd-start FDT_ERR_NOSPACE."): What I got is an error: "WARNING: could not set linux,initrd-start FDT_ERR_NOSPACE." after loading Device Tree blob. This in turn caused linux to miss init part. After some digging, I found out the reason for this error, it is caused by fdt_resize(). FDT blob got resized after filling in all board specific information of PowerPC. (in boot_body_linux()). It reduced blob size with only extra space for two fdt_reserve_entry, one for fdt itself, and one for initrd. Then it's aligned to a 0x1000 page boundary. However, later in fdt_initrd(), it could add two more properties, initrd-start AND initrd-end, each one needs at least two fdt_reserve_entry sizes done by _fdt_add_property() (name and value). Thus, the two fdt_reserve_entry extra space is not sufficient. So for some specific fdt size which is just under the page boundary after resizing, this will cause an error of FDT_ERR_NOSPACE in fdt_initrd() when setting those two properties, and failed to pass initrd information to linux. My fix is in fdt_resize(), leave at least 4 fdt_reserve_entry for initrd. So instead of 2*sizeof(struct fdt_reserve_entry) for actual_totalsize, use 5*sizeof(struc fdt_reserve_entry). Stefan: I got this same error on katmai, when trying to boot with initrd (run flash_self). This patch fixes this issue. Signed-off-by: Feng Wang <fwang02@harris.com> Tested-by: Stefan Roese <sr@denx.de> Cc: Jerry Van Baren <gvb.uboot@gmail.com> Acked-by: Gerald Van Baren <vanbaren@cideas.com>
2010-08-08board/purple/flash.c: removed unneded variableFrans Meulenbroeks
removed a variable that was not used Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
2010-08-08various cmd_* files: fixed layout a little bitFrans Meulenbroeks
Most of the files have U_BOOT_CMD on a separate line, but a few didn't and had the first line on the same line as U_BOOT_CMD. This changes these files by adding a line break and a tab Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
2010-08-08various cmd_* files: remove the command name from the help messageFrans Meulenbroeks
removed the command name from the help message as it is already printed. for cmd_mmc also rewrote the message a little bit Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>