summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2012-02-12mmc: access mxcmmc from mx31 boardsHelmut Raiger
This patch modifies mxcmmc.c to be used not only by i.MX27 but also by i.MX31 boards. Both use the same SD controller, but have different clock set-ups. The i.MX27 imx_get_XXXclock functions are made static to generic.c and a public mxc_get_clock() function is provided. Pins, base address and prototypes for an i.MX31 specific board_init_mmc() are provided. Some of the i.MX27 clock getters are unused and marked as such to avoid warnings (./MAKEALL -s mx27), but the code was left in for future use. Signed-off-by: Helmut Raiger <helmut.raiger@hale.at> Acked-by: Stefano Babic <sbabic@denx.de>
2012-02-12i.mx6q: mx6qsabrelite: Add the ethernet function supportJason Liu
Signed-off-by: Jason Liu <jason.hui@linaro.org> Signed-off-by: Eric Miao <eric.miao@linaro.org> CC: Jason Liu <jason.hui@linaro.org> CC: Stefano Babic <sbabic@denx.de>
2012-02-12i.mx6q: configs: Add fdt_high and initrd_high variablesDirk Behme
To be able to load the device tree and initrd correctly, set the fdt_high and initrd_high environment variables. Using 0xffffffff implies that the device tree and the initrd are initially copied to working addresses. This will avoid an additional copy. Loading the device tree to 0x30000000 and the initrd to 0x3c000000 should work for both boards, the ARM2 and SabreLite. Example (SabreLite): fatload mmc 0:2 0x10000000 uImage fatload mmc 0:2 0x3c000000 uInitrd fatload mmc 0:2 0x30000000 board.dtb bootm 0x10000000 0x3c000000 0x30000000 Note: This requires that the kernel has CONFIG_HIGHMEM enabled. Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com> CC: Jason Liu <jason.hui@linaro.org> CC: Stefano Babic <sbabic@denx.de> Acked-by: Jason Liu <jason.hui@linaro.org>
2012-02-12i.mx6q: mx6qsabrelite: Setup uart1 pinmuxTroy Kisky
This allows the Linux kernel to use UART1 before pinmux support is added for UART1 Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com> CC: Troy Kisky <troy.kisky@boundarydevices.com> CC: Jason Liu <jason.hui@linaro.org> CC: Stefano Babic <sbabic@denx.de> Acked-by: Jason Liu <jason.hui@linaro.org>
2012-02-12i.mx6: mx6x_pins: Fix uart txd definitionsTroy Kisky
The uart txd pad can also provide the rxd function. But it does not stop its tx role. This could be used for a half duplex serial port. Change names to reduce confusion. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com> CC: Troy Kisky <troy.kisky@boundarydevices.com> CC: Jason Liu <jason.hui@linaro.org> CC: Stefano Babic <sbabic@denx.de> Acked-by: Jason Liu <jason.hui@linaro.org>
2012-02-12imximage: Sort bootops alphabeticallyDirk Behme
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com> CC: Fabio Estevam <festevam@gmail.com> CC: Stefano Babic <sbabic@denx.de> CC: Jason Liu <jason.hui@linaro.org> Acked-by: Jason Liu <jason.hui@linaro.org>
2012-02-12imximage: Add support for i.MX6Dirk Behme
The i.MX6 processor can boot from NOR flash and SATA disks, additionally. Add the flash offsets for these additional boot modes. Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com> Signed-off-by: Fabio Estevam <festevam@gmail.com> CC: Stefano Babic <sbabic@denx.de> CC: Jason Liu <jason.hui@linaro.org> Acked-by: Jason Liu <jason.hui@linaro.org>
2012-02-12imximage: Add MX53 to the documentationDirk Behme
i.MX53 is supported, too. Add this to the introduction of the documentation. Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com> CC: Fabio Estevam <festevam@gmail.com> CC: Stefano Babic <sbabic@denx.de> CC: Jason Liu <jason.hui@linaro.org>
2012-02-12sdhc_boot: Introduce CONFIG_FSL_FIXED_MMC_LOCATION optionFabio Estevam
Since commit 97039ab98 (env_mmc: Allow board code to override the environment address) mmc_get_env_addr is a weak-aliased function in common/env_mmc.c The mmc_get_env_addr implementation that exists at board/freescale/common/sdhc_boot.c is meant to be used only for PowerPC boards, but currently it is being used for all platforms that have CONFIG_ENV_IS_IN_MMC defined. Introduce CONFIG_FSL_FIXED_MMC_LOCATION so that the boards that need to use the mmc_get_env_addr version from board/freescale/common/sdhc_boot.c could activate this config option on their board file. This fixes the retrieval of CONFIG_ENV_OFFSET on non-PowerPC boards. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Kumar Gala <galak@kernel.crashing.org> Acked-by: Stefano Babic <sbabic@denx.de>
2012-02-12arm, davinci: cam_enc_4xx board updatesHeiko Schocher
- CONFIG_SYS_MMC_ENV_DEV, needed if environment on mmc - wait for 1 second timer in board_late_init() only, if timer is running. - add UBI/UBIFS support - add FIT images support - menu support - U-Boot max size now 0xa0000 - SPL now Block 0 page 0 - new MTD partitioning 0x00000000 SPL 0x00020000 UBL-Header 0x00040000 UBL-Header 0x00060000 UBL-Header 0x00080000 UBoot (0xa0000(U-Boot length) + 0x60000(3 spare blocks)) 0x00180000 ENV- Variablen (1) 0x001a0000 ENV- Variablen (2) 0x001c0000 ENV- Variablen (reserved for Bad Block) 0x001e0000 ENV- Variablen (reserved for Bad Block) 0x00200000 UBI-Device UBI Volumes: „default“: contain environment-default values „rootfs1“: UBIFS root-fs (1); contain linux kernel image „rootfs2“: UBIFS root-fs (2); contain linux kernel image „data-ro“: UBIFS data (read only) „data-rw“: UBIFS data (read/write) - new environment variables: - app_reset (this is only passed per cmdline to linux) - dvn_app_vers string from ramdisk description contained in the FIT image - dvn_boot_vers string from ubootimage description contained in the FIT image - saveparms, restoreparms, restoretmpparms, savetmpparms helper for saving network parameter. - ubiargs set ubi kernel cmdlinargs for booting with a ubifs rootfs - ubi_ubi boot with reading kernel image from ubifs, and use a ubifs as rootfs Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Sandeep Paulraj <s-paulraj@ti.com> Cc: Tom Rini <tom.rini@gmail.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Cc: Mike Frysinger <vapier@gentoo.org> Cc: Wolfgang Denk <wd@denx.de>
2012-02-12common, menu: do not trigger timeout again, if a line is readHeiko Schocher
Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Jason Hobbs <jason.hobbs@calxeda.com> Acked-by: Jason Hobbs <jason.hobbs@calxeda.com>
2012-02-12common, menu: show menu on startup if CONFIG_MENU_SHOW is definedHeiko Schocher
show a menu on startup instead running the shell. Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Jason Hobbs <jason.hobbs@calxeda.com> Cc: Mike Frysinger <vapier@gentoo.org> Acked-by: Jason Hobbs <jason.hobbs@calxeda.com>
2012-02-12common, menu: add statusline supportHeiko Schocher
add the possibility to show a statusline when printing a menu Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Jason Hobbs <jason.hobbs@calxeda.com> Cc: Mike Frysinger <vapier@gentoo.org> Acked-by: Mike Frysinger <vapier@gentoo.org>
2012-02-12common: add possibility for readline_into_buffer timeoutHeiko Schocher
add possibility to add a timeout when reading a line into a buffer. Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Mike Frysinger <vapier@gentoo.org> Acked-by: Mike Frysinger <vapier@gentoo.org>
2012-02-12arm, davinci: add timer defines for tcr fieldHeiko Schocher
Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Sandeep Paulraj <s-paulraj@ti.com> Cc: Tom Rini <tom.rini@gmail.com>
2012-02-12arm, davinci: add workaround for not resetting DMA bus and VPSS modulesHeiko Schocher
The Buffer Logic of VPSS is Not Reset by System Reset Pin, see http://www.ti.com/lit/er/sprz316b/sprz316b.pdf chapter Advisory 1.2.1 on page 9. Add workaroundcode proposed in the errata. Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Sandeep Paulraj <s-paulraj@ti.com> Cc: Tom Rini <tom.rini@gmail.com>
2012-02-12OMAP SPL: Fix missing timer_init() call in OMAP4 s_init()Dechesne, Nicolas
In 8775471bb, the call to timer_init() was removed from common code and put in OMAP3 s_init() function. As a result the boot was broken on OMAP4. This patch adds timer_init() in OMAP4 s_init(), that fix boot on all OMAP4 boards. Signed-off-by: Nicolas Dechesne <n-dechesne@ti.com> Tested-by: Robert P. J. Day <rpjday@crashcourse.ca> Cc: Sandeep Paulraj <s-paulraj@ti.com> Cc: Tom Rini <trini@ti.com>
2012-02-12OMAP3: Add Corscience Tricorder boardThomas Weber
Tricorder is a board which is very similar to the Devkit8000. It is designed as a base platform for further medical devices. www.corscience.de/en/medical-engineering/products/multiparameter/mp10-board.html Signed-off-by: Thomas Weber <weber@corscience.de>
2012-02-12OMAP3: Correct get_sdr_cs_offset maskTom Rini
The function get_sdr_cs_offset reads the CS_CFG register in the SDRC to determine where CS1 is mapped to. make_cs1_contiguous() will set CS1 to follow after CS0. The CS_CFG register has values in bits 9:8 and 3:0 but we had erroneously been testing 5:4 and 3:0 resulting in incorrect offsets on platforms with less than 128MB as 3:0 describe 128MB hunks and 9:8 describe 32MB offsets after the 128MB hunk. Tested-by: Grant Erickson <marathon96@gmail.com> Signed-off-by: Tom Rini <trini@ti.com>
2012-02-12Beagleboard: Correct memory size on rev C4robertcnelson@gmail.com
The logic for the rev C4 boards was missing one of the cases (variant with Micron NAND and 2x128MB). Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
2012-02-12am3517evm: remove rootfstype kernel parameter for MMC boot deviceYegor Yefremov
it is not necessary to define rootfstype for mass storage devices. Kernel detects it automatically. Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
2012-02-12arm: omap3: Define save_boot_params in lowlevel_init.S for SPL onlyPali Rohár
Wrap the function save_boot_params with CONFIG_SPL_BUILD. This will allow non-SPL boards to define their own save_boot_params functions in U-Boot itself. Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
2012-02-12arm, davinci: add PLL0 prediv to da850 lowlevel setupBen Gardiner
The OMAP-L138 has a pre-divider available on PLL0. Add support to da850_lowlevel.c for configuring PLL0's pre-divider. This is to achieve certain OPP's -- e.g. the 372MHz OPP used also by Linux. Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca> Cc: Christian Riesch <christian.riesch@omicron.at> CC: Heiko Schocher <hs@denx.de> Cc: Sandeep Paulraj <s-paulraj@ti.com> Cc: Tom Rini <tom.rini@gmail.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Acked-by: Heiko Schocher <hs@denx.de> Acked-by: Christian Riesch <christian.riesch@omicron.at>
2012-02-12tegra2: Enable data cacheSimon Glass
This enables the data cache on Tegra2 boards. As discussed on the list, this is better off in the Tegra2 cpu code than in a particular vendor directory. We should be safe turning on the cache for all Tegra2 boards. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-02-12tegra: mmc: Support operation with dcache enabledSimon Glass
When the data cache is enabled we must flush on write and invalidate on read. We also check that buffers are aligned to data cache lines boundaries. With recent work in U-Boot this should generally be the case but the warnings will catch problems. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-02-12tegra: Use funcmux for MMC on seaboardSimon Glass
Use the new funcmux_select() feature to set up the MMC pin mux. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-02-12tegra: Use funcmux for MMC on harmonySimon Glass
Use the new funcmux_select() feature to set up the MMC pin mux. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-02-12tegra: Use funcmux for MMC on tamontenSimon Glass
Use the new funcmux_select() feature to set up the MMC pin mux. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-02-12tegra: Add SDMMC support to funcmuxSimon Glass
This adds support for SDMMC ports to the funcmux. Only one option is supported: FUNCMUXO_SDMMC_8BIT which selects an 8-bit wide SDIO interface where available. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-02-12tegra: Add I2C support to funcmuxSimon Glass
Add support to funcmux for selecting I2C functions and programming the pinmux appropriately. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-02-12tegra: Add enum to select from available funcmux configsSimon Glass
We want to give a name to each available funcmux config. For now we just use the pin group names (even through it is verbose) since there seems to be nothing better. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-02-12tegra: Adjust funcmux config test to permit expansionSimon Glass
We want to support config options other than zero, so move the test to the end to allow intermediate code to OK such a config. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-02-12tegra2: Add support for Compal Paz00 (Toshiba AC100)Stephen Warren
The Toshiba AC100 (Compal code-name Paz00, aka Dynabook AZ) is a netbook derived from the NVIDIA Tegra Harmony reference board. It ships with Android, but is often repurposed to run Linux. This patch adds just enough support to get a U-Boot serial console, and the ability access built-in eMMC and the external SD slot. v2: * Rebased on latest HEAD, incorporated changes made to other board files. * Moved board files from board/nvidia to board/compal. * Switched to correct odmdata value. This required add the previous patch to fix U-Boot's interpretation of the odmdata RAM size field. * Removed nvmem= from default Linux kernel command-line; no drivers use the reserved memory yet, so there's no point reserving it. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-02-12tegra2: Fix default RAM size selection in odmdataStephen Warren
A value of 0 in the odmdata RAM size field means default, which is 512MB not 1GB. Fix this. For reference, see: http://nv-tegra.nvidia.com/gitweb/?p=linux-2.6.git;a=blob;\ f=arch/arm/mach-tegra/odm_kit/query/harmony/tegra_devkit_custopt.h;\ h=1ec7010911454f19a5018952fd245785a62c59ad;\ hb=0e52d7fe25b11a656c376a37890be219470661fb v2: New patch Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-02-12tegra2: Fix conflicting pinmux for UARTAStephen Warren
Tegra appears to boot with function UARTA pre-selected on mux group SDB. If two mux groups are both set to the same function, it's unclear which group's pins drive the RX signals into the HW module. For UARTA, SDB certainly overrides group IRTX in practice. To solve this, configure some alternative function on SDB to avoid the conflict. Also, tri-state the group to avoid driving any signal onto it until we know what's connected. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-02-11fw_env.h: fix commentFrans Meulenbroeks
made description according to implementation (where the config file is the default). Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
2012-02-11Merge branch 'master' of /home/wd/git/u-boot/custodiansWolfgang Denk
* 'master' of /home/wd/git/u-boot/custodians: add STM29F400BB to table of supported legacy flashs * Fix: watchdog timed out, if flash blank (0xFF) blocks
2012-02-11Merge branch 'master' of git://git.denx.de/u-boot-cfi-flashWolfgang Denk
* 'master' of git://git.denx.de/u-boot-cfi-flash: add STM29F400BB to table of supported legacy flashs * Fix: watchdog timed out, if flash blank (0xFF) blocks
2012-02-11Merge branch 'master' of /home/wd/git/u-boot/custodiansWolfgang Denk
* 'master' of /home/wd/git/u-boot/custodians: nand/fsl_elbc: Convert to self-init nand: Introduce CONFIG_SYS_NAND_SELF_INIT nand_spl: store ecc data on the stack mtd/nand: Add ONFI support for FSL NAND controller nand: make 1-bit software ECC configurable nand: Sanitize ONFI strings. nand: Merge changes to BBT from Linux nand driver nand: Merge changes from Linux nand driver nand: cleanup whitespace nand: Add more NAND types from Linux nand driver nand: Merge BCH code from Linux nand driver NAND: Remove additional (CONFIG_SYS)_NAND_MAX_CHIPS NAND: remove NAND_MAX_CHIPS definitions nand_spl_simple: store ecc data on the stack
2012-02-11Merge branch 'master' of git://git.denx.de/u-boot-nand-flashWolfgang Denk
* 'master' of git://git.denx.de/u-boot-nand-flash: nand/fsl_elbc: Convert to self-init nand: Introduce CONFIG_SYS_NAND_SELF_INIT nand_spl: store ecc data on the stack mtd/nand: Add ONFI support for FSL NAND controller nand: make 1-bit software ECC configurable nand: Sanitize ONFI strings. nand: Merge changes to BBT from Linux nand driver nand: Merge changes from Linux nand driver nand: cleanup whitespace nand: Add more NAND types from Linux nand driver nand: Merge BCH code from Linux nand driver NAND: Remove additional (CONFIG_SYS)_NAND_MAX_CHIPS NAND: remove NAND_MAX_CHIPS definitions nand_spl_simple: store ecc data on the stack
2012-02-11Merge branch 'master' of /home/wd/git/u-boot/custodiansWolfgang Denk
* 'master' of /home/wd/git/u-boot/custodians: ARM: AM33XX: Add i2c support ARM: AM33XX: Add AM33XX I2C driver support ARM: I2C: I2C Multi byte address support
2012-02-09add STM29F400BB to table of supported legacy flashsDavid Müller (ELSOFT AG)
Signed-off-by: David Mueller <d.mueller@elsoft.ch> Signed-off-by: Stefan Roese <sr@denx.de>
2012-02-09* Fix: watchdog timed out, if flash blank (0xFF) blocksJens Scharsig (BuS Elektronik)
The current implementation of cfi_flash uses udelay to reset watchdog. If several blocks are blank (0xff filled) the watchdog timed out. The reason is, udelay is never called, if flash device is ready to fast. e.g. mw.w $(copy_addr) FFFF 10000;cp.b $(copy_addr) 10880000 20000 -> watchdog timed out mw.w $(copy_addr) 0000 10000;cp.b $(copy_addr) 10880000 20000 -> watchdog not timed out This patch adds an extra watchdog reset in front of flash ready check. Signed-off-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de> Signed-off-by: Stefan Roese <sr@denx.de>
2012-01-26nand/fsl_elbc: Convert to self-initScott Wood
This driver doesn't yet make use of the added flexibility (not that that should stop anyone from converting...), but it will with the in-progress hack to support 4k-page NAND. Signed-off-by: Scott Wood <scottwood@freescale.com>
2012-01-26nand: Introduce CONFIG_SYS_NAND_SELF_INITScott Wood
This allows a driver to run code between nand_scan_ident() and nand_scan_tail(), among other things. See the additions to doc/README.nand for details. To allow a gradual transition, Boards that don't set CONFIG_SYS_NAND_SELF_INIT will still be initialized the old way, but new drivers should not require this, and existing drivers should be converted when convenient. Signed-off-by: Scott Wood <scottwood@freescale.com>
2012-01-26nand_spl: store ecc data on the stackScott Wood
Adapt the following patch from spl to nand_spl: Author: Stefano Babic <sbabic@denx.de> Date: Thu Dec 15 10:55:37 2011 +0100 nand_spl_simple: store ecc data on the stack Currently nand_spl_simple puts it's temp data at 0x10000 offset in SDRAM which is likely to contain already loaded data. The patch saves the oob data and the ecc on the stack replacing the fixed address in RAM. Signed-off-by: Stefano Babic <sbabic@denx.de> CC: Ilya Yanok <yanok@emcraft.com> CC: Scott Wood <scottwood@freescale.com> CC: Tom Rini <tom.rini@gmail.com> CC: Simon Schwarz <simonschwarzcor@googlemail.com> CC: Wolfgang Denk <wd@denx.de> Signed-off-by: Scott Wood <scottwood@freescale.com> While nand_spl is on its way out, in favor of spl, there are still many boards using it, and conversions are gradual. This allows us to get rid of CONFIG_SYS_NAND_ECCSTEPS and CONFIG_SYS_NAND_ECCTOTAL now, which would otherwise be likely to linger unreferenced after a conversion. It also eliminates a temporary error in the hawkboard_nand build, since the spl version of the patch removed ECCSTEPS/TOTAL from hawkboard.h, but the spl conversion is pending (and may be merged via a different tree). Signed-off-by: Scott Wood <scottwood@freescale.com>
2012-01-26mtd/nand: Add ONFI support for FSL NAND controllerShengzhou Liu
- fix NAND_CMD_READID command for ONFI detect. - add NAND_CMD_PARAM command to read the ONFI parameter page. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
2012-01-26nand: make 1-bit software ECC configurableChristian Hitz
The software ECC algorithm is not necessary when hardware ECC is available and can be left out for a smaller image size. Enable with CONFIG_MTD_ECC_SOFT. Signed-off-by: Christian Hitz <christian.hitz@aizo.com> Cc: Scott Wood <scottwood@freescale.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
2012-01-26nand: Sanitize ONFI strings.Christian Hitz
[backport from linux commit 02f8c6aee8df3cdc935e9bdd4f2d020306035dbe] This is part of the synchronization with the nand driver to the Linux 3.0 state. Signed-off-by: Christian Hitz <christian.hitz@aizo.com> Cc: Scott Wood <scottwood@freescale.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
2012-01-26nand: Merge changes to BBT from Linux nand driverChristian Hitz
[backport from linux commit 02f8c6aee8df3cdc935e9bdd4f2d020306035dbe] This patch synchronizes the nand driver with the Linux 3.0 state. Signed-off-by: Christian Hitz <christian.hitz@aizo.com> Cc: Scott Wood <scottwood@freescale.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
generated by cgit v0.10.2 at 2024-07-14 02:45:29 (GMT)