| Age | Commit message (Collapse) | Author |
|---|
|
We should have a size value for these. Add one in each case. This will
be needed for PCI.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Support running U-Boot as a coreboot payload. Tested peripherals include:
- Video (HDMI and DisplayPort)
- SATA disk
- Gigabit Ethernet
- SPI flash
USB3 does not work. This may be a problem with the USB3 PCI driver or
something in the USB3 stack and has not been investigated So far this is
disabled. The SD card slot also does not work.
For video, coreboot will need to run the OPROM to set this up.
With this board, bare support (running without coreboot) is not available
as yet.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Since Chromebooks mostly have similar configuration, put it in a common
file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Add Lynxpoint to the driver so that the Asus Chromebox can be supported.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
|
|
Add some new device IDs used by this haswell-based chipset.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
At present a VGA console assumes a keyboard unless a CONFIG option is set.
This difference can be dealt with by a device tree option, allowing boards
that are otherwise the same to use the same configuration.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Some systems have more than 4GB of RAM. U-Boot can only place things below
4GB so any memory above that should not be used. Ignore any such memory so
that the memory size will not exceed the maximum.
This prevents gd->ram_size exceeding 4GB which causes problems for PCI
devices which use DMA.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
|
|
Commit d3cfcb3 (ARM: DRA7: Enable clocks for USB OTGSS and USB PHY)
changed the member names of prcm_regs from cm_l3init_usb_otg_ss_clkctrl
to cm_l3init_usb_otg_ss1_clkctrl and from cm_coreaon_usb_phy_core_clkctrl
to cm_coreaon_usb_phy1_core_clkctrl in order to differentiate between
the two dwc3 controllers present in dra7xx/am43xx and enabled these
clocks in enable_basic_clocks() in hw_data.c. However these clocks
continued to be enabled in board files/driver files for dwc3 host
mode functionality causing compilation break with few configs.
Fixed it here by making all the clocks enabled in enable_basic_clocks()
and removing it from board files/driver files here.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
|
|
Sunxi platforms come with at least 3 TWI (I2C) controllers and some platforms
even have up to 5. This adds support for every controller on each supported
platform, which is especially useful when using expansion ports on single-board-
computers.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Orion5x, Kirkwood and Armada XP platforms come with a single TWSI (I2C) MVTWSI
controller. However, other platforms using MVTWSI may come with more: this is
the case on Allwinner (sunxi) platforms, where up to 4 controllers can be found
on the same chip.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Heiko Schocher <hs@denx.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
The iNet 3F is an A10 tablet with 1GiB RAM and a 1024x768 screen.
Also see: http://linux-sunxi.org/INet_3F
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
The iNet 3W is an A10 tablet with 1GiB RAM and a 1024x768 screen.
Also see: http://linux-sunxi.org/INet_3W
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
The official name for the iNet manufacturer is iNet with a lowercase i and an
uppercase N.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Michal Suchanek <hramrach@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
A few dram files were still listed as maintained even though they were removed
some time ago
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
This allows enabling MUSB (on the OTG port).
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
vbus-usable may not get set if power is provided through both the power barrel
connector and external 5v is also present on the otg connector, at least on
boards where vbus is also controlled through the axp221-pmic.
One way to reproduce this is to bootup an Ippo-q8h board with a usb-host
cable plugged into the otg (so that it will get powered), then unplug the
usb-host cable and plug in a charger, and then do "reset" on the u-boot
console, vbus-usable will then report 0, leading to uboot trying to provide
power to the otg port even though external 5v is present, this commit fixes
this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
When u-boot boots the board may be powering vbus, we turn off vbus in
sunxi_usbc_request_resources, if we are too quick with reading vusb-detect
after this we may see a residual charge and assume we've an external vusb
connected even though we do not. So when we see an external vusb wait a bit
and try again.
Without this when dealing with a pmic controller vbus and doing "reset" on
the u-boot console the musb host will only init once every other boot, because
the other boot it thinks an external vbus is present, this commit fixes this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
On boards which use the pmic to enable/disable vbus on the otg port, the
vbus value is not reset to 0 on reset, as reset only resets the SoC and not
the pmic, so explicitly set vbus to 0 on init (request_resources) by moving
the gpio_direction_output call into request_resources.
For consistency also move the gpio_direction_input call for vbus-detect into
request_resources.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
The Yones Toptech BD1078 is an A20 based 10" tablet with a 1024x600 lcd screen,
volume up/down and back buttons, headphones jack, mini hdmi, micro usb (otg),
micro usb (host), external micro-sd slot and a separate internal micro-sd slot.
Also see: http://linux-sunxi.org/Yones_Toptech_BD1078
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Sunxi platforms have different possible mmc pin mux setups (except for mmc0),
which are different across platforms.
This lets users configure which is used through the CONFIG_MMC*_PINS Kconfig
options. This is especially relevant when a second (in addition to mmc0) port
is used and CONFIG_MMC_SUNXI_SLOT_EXTRA is enabled.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Each hardware feature exposed through the GPIO pin mux is usually using the same
function index (for a given port), so there is no need to define one value per
pin: one value per hardware feature per port is sufficient, avoids duplication
and makes everything easier to understand.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
The Ainol AW1 is an A20 based tablet with a 800x480 lcd screen, sdio wifi,
volume up/down and home buttons, micro-sd slot, micro usb (otg), headphones
connector and a SPCI modem connector.
Also see: http://linux-sunxi.org/Ainol_AW1
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
VBUS detection could be needed not only by the musb code (to prevent host mode),
but also by e.g. gadget drivers to start only when a cable is connected.
In addition, this allows more flexibility in vbus detection, as it could easily
be extended to other USBC indexes. Eventually, this would help making musb
support independent from a hardcoded USB controller index (0).
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
VBUS detection and enable is now be used with virtual AXP GPIOs, so all the USB
code has to use GPIO in every case and let sunxi_gpio do the heavy lifting.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
This converts the VBUS detection and enable logic to GPIO instead of separate
axp functions and checks that have to be used aside usual GPIO functions.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
The Mixtile LOFT-Q is an A31 based board with 2G RAM, 8G EMMC, sdio wifi,
1Gbit ethernet, HDMI display, toslink audio plug, 4 USB2.0 port, external
USB2SATA connector, sd card plug, 3x60 external fpic expansion connector,
NXP JN5168 zigbee gw, remote support.
Also see http://focalcrest.com/en/pc.html#pro02
Signed-off-by: Han Pengfei <pengphei@sina.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
|
|
The "fastboot reboot-bootloader" command is defined to
re-enter into fastboot mode after rebooting into
bootloader. This command is usually used after updating
bootloader via fastboot.
This commit implements only a generic side of the
command - setting of the reset flag and then resetting.
Setting of the reset flag is implemented using __weak
fb_set_reboot_flag() function. The actual setting and
checking of the reset flag should be implemented by
a boot script and/or board/SoC specific code.
Signed-off-by: Alexey Firago <alexey_firago@mentor.com>
Tested-by: Steve Rae <srae@broadcom.com>
[Test HW: bcm28155_ap board]
|
|
Implement an alias name check for devices where GPT limitations prevent
user-friendly partition names such as "boot", "system" and "cache". Or,
where the actual partition name doesn't match a standard partition name
used commonly with fastboot.
To set an alias, add an environment setting as follows:
fastboot_partition_alias_<alias partition name>=<actual partition name>
Example: fastboot_partition_alias_boot=LNX
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Acked-by: Steve Rae <srae@broadcom.com>
Cc: Steve Rae <srae@broadcom.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
|
|
trigger watchdog before calling usb_gadget_handle_interrupts()
This prevents board resets when calling dfu command on boards
which have a watchdog.
Signed-off-by: Heiko Schocher <hs@denx.de>
[ Reedition by Lukasz Majewski <l.majewski@samsung.com> to apply to
v2014.04 release ]
|
|
USB Mass Storage is the standard name, so let's use it here.
Suggested-by: Soeren Moch <smoch@web.de>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
|
|
Storing thor device struct as an EP private data. It is necessary for
DWC3 operation.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
|
|
For u-boot dwc3 driver the scatter gather list support has been removed
from original linux code. It is correct, since we try to send one request
at a time.
However, the cleanup left spurious break, which caused early exit from
loop at dwc3_cleanup_done_reqs() function. As a result the dwc3_gadget_giveback()
wasn't called and caused USB Mass Storage to hang.
This commit removes this problem and refactor the code to remove superfluous
do { } while(1) loop.
Test HW: Odroid XU3 (with ./test/ums/ums_gadget_test.sh)
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
|
|
Commit "drivers/dwc3: add a workaround for too small OUT requests"
sets max packet for OUT requests when transfer is smaller.
Until this change the default maxpacket for non EP0 EPs was 1024. This is
too much, since UMS LBA size is 512B
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
|
|
be LST
It turned out that current dwc3 gadget code is preparing multiple TRBs
for a transfer. Unfortunately, when multiple requests are in the same
queue, only for the last one the LST (last) ctrl bit is set.
Due to that dwc3 HW executes all TRBs up till the one marked as last.
Unfortunately, UMS requires call of ->complete callback after any send TRB.
This is the reason for "hangs" in executing UMS.
This code simplifies this situation and set each TRB's ctrl field bit to be
last (LST bit).
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
|
|
There is no point in calling dwc3_thread_interrupt() if no event is
pending. There is also no point in flushing event cache in EVERY loop
iteration.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
|
|
This patch adds code to select standard, commonly used usb endpoint
configuration (ep1in-bulk, ep2out-bulk, ep3in-int) to dwc3 driver. This
ensures compatibility with old userspace and windows drivers, which
expects hardcoded endpoint numbers.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
|
